Document Center List of Standards on Thermoplastic Materials
ICS Code 83.080.20
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1147 - Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics
- ASTM-D1238 - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
- ASTM-D1243 - Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers
- ASTM-D1430 - Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
- ASTM-D1431 - Specification for Styrene-Acrylonitrile Copolymer Molding and Extrusion Materials (Withdrawn 1984) Replaced by ASTM-D4203
- ASTM-D1457 - Specification for Polytetrafluorethylene (PTFE) Molding and Extrusion Materials (Withdrawn 1996)
- ASTM-D1531 - Standard Test Methods for Relative Permittivity (Dielectric Constant) and Dissipation Factor by Fluid Displacement Procedures
- ASTM-D1601 - Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers
- ASTM-D1693 - Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
- ASTM-D1784 - Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
- ASTM-D1786 - Standard Specification for Toluene Diisocyanate
- ASTM-D1788 - Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Plastics (Withdrawn 1988)
- ASTM-D1897 - Recommended Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials (Withdrawn 1992)
- ASTM-D1927 - Specification for Rigid Poly (Vinyl Chloride) Plastic Sheet (Withdrawn 1994)
- ASTM-D1986 - Standard Test Method for Determining the Apparent Viscosity of Polyethylene Wax
- ASTM-D1996 - Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Low Density Polyethylene Using Liquid Chromatography (LC) (Withdrawn 2009)
- ASTM-D2115 - Standard Practice for Oven Heat Stability of Poly(Vinyl Chloride) Compositions
- ASTM-D2116 - Standard Specification for FEP Resin Molding and Extrusion Materials
- ASTM-D2123 - Specification for Rigid Poly (Vinyl Chloride-Vinyl Acetate) Plastic Sheet (Withdrawn 1987)
- ASTM-D2146 - Specification for Propylene Plastic Molding and Extrusion Materials (Withdrawn 1985)
- ASTM-D2151 - Standard Practice for Staining of Poly(Vinyl Chloride) Compositions by Rubber Compounding Ingredients (Withdrawn 2003)
- ASTM-D2238 - Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm−1
- ASTM-D2287 - Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds
- ASTM-D2292 - Recommended Practice for Compression Molding Test Specimens of Styrene-Butadiene Molding and Extrusion Materials (Withdrawn 1992)
- ASTM-D2463 - Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic Containers
- ASTM-D2464 - Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
- ASTM-D2473 - Specification for Polycarbonate Molding, Extrusion, and Casting Materials (Withdrawn 1982)
- ASTM-D2538 - Standard Practice for Fusion of Poly(Vinyl Chloride) (PVC) Compounds Using a Torque Rheometer
- ASTM-D2561 - Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
- ASTM-D2647 - Standard Specification for Crosslinkable Ethylene Plastics
- ASTM-D2740 - Specification for Polyvinyl Chloride (PVC) Plastic Tubing (Withdrawn 1989)
- ASTM-D2765 - Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
- ASTM-D2839 - Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
- ASTM-D2848 - Specification for Reinforced Polycarbonate Injection Molding and Extrusion Materials (Withdrawn 1982)
- ASTM-D2853 - Specification for Reinforced Olefin Polymers for Injection Molding and Extrusion (Withdrawn 1987)
- ASTM-D2897 - Specification for Reinforced and Filled Nylon Injection Molding and Extrusion Materials (Withdrawn 1983)
- ASTM-D2951 - Standard Test Method for Resistance of Types III and IV Polyethylene Plastics to Thermal Stress-Cracking (Withdrawn 2006)
- ASTM-D2952 - Specification for Ethylene Plastics (Withdrawn 1999)
- ASTM-D3011 - Specification for Reinforced and Filled Polystyrene, Styrene-Acrylonitrile, and ABS for Molding and Extrusion (Withdrawn 1987)
- ASTM-D3012 - Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven
- ASTM-D3027 - Practice for Compression Molding Specimens of Allyl Molding Compounds (Withdrawn 1992)
- ASTM-D3030 - Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins
- ASTM-D3124 - Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry
- ASTM-D3159 - Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials
- ASTM-D3222 - Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
- ASTM-D3275 - Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
- ASTM-D3287 - Specification for Biaxially Oriented Polyethylene (PEO) Plastic Pipe (SDR-PR) Based on Controlled Outside Diameter (Withdrawn 1989)
- ASTM-D3349 - Standard Test Method for Absorption Coefficient of Ethylene Polymer Material Pigmented with Carbon Black
- ASTM-D3364 - Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications
- ASTM-D3367 - Standard Test Method for Plasticizer Sorption of Poly(Vinyl Chloride) Resins Under Applied Centrifugal Force
- ASTM-D3536 - Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by Liquir Exclusion Chromatography (Gel Permeation Chromatography - GPC) (Withdrawn 1996)
- ASTM-D3548 - Standard Specification for Ethyl Acrylate
- ASTM-D3591 - Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds
- ASTM-D3594 - Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers (Withdrawn 2019)
- ASTM-D3641 - Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
- ASTM-D3678 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions
- ASTM-D3679 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
- ASTM-D3748 - Standard Practice for Evaluating High-Density Rigid Cellular Plastics
- ASTM-D3749 - Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique
- ASTM-D3826 - Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
- ASTM-D3835 - Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
- ASTM-D3895 - Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
- ASTM-D3935 - Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- ASTM-D4066 - Standard Classification System for Nylon Injection and Extrusion Materials (PA)
- ASTM-D4094 - Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers (Withdrawn 2015)
- ASTM-D4101 - Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
- ASTM-D4181 - Standard Classification for Acetal (Pom) Molding and Extrusion Materials (Withdrawn 2005)
- ASTM-D4203 - Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
- ASTM-D4216 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds
- ASTM-D4218 - Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
- ASTM-D4226 - Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
- ASTM-D4273 - Standard Test Method for Polyurethane Raw Materials: Determination of Primary Hydroxyl Content of Polyether Polyols
- ASTM-D4274 - Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols
- ASTM-D4275 - Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in Polymers of Ethylene and Ethylene–Vinyl Acetate (EVA) Copolymers by Gas Chromatography
- ASTM-D4349 - Classification System and Basis for Specification for Polyphenylene Ether (PPE) Materials
- ASTM-D4440 - Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology
- ASTM-D4441 - Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene
- ASTM-D4443 - Standard Test Method for Determining Residual Vinyl Chloride Monomer Content in PPB Range in Vinyl Chloride Homo- and Co-Polymers by Headspace Gas Chromatography
- ASTM-D4477 - Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
- ASTM-D4507 - Specification for Thermoplastic Polyester (TPES) Materials (Withdrawn 1999)
- ASTM-D4591 - Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
- ASTM-D4603 - Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
- ASTM-D4634 - Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
- ASTM-D4659 - Standard Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates
- ASTM-D4662 - Standard Test Methods for Polyurethane Raw Materials: Determination of Acid and Alkalinity Numbers of Polyols
- ASTM-D4665 - Test Method For Polyurethane Raw Materials: Determination Of Assay Of Isocyanate S (Withdrawn 1992)
- ASTM-D4669 - Standard Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols
- ASTM-D4670 - Standard Test Method for Polyurethane Raw Materials: Determination of Suspended Matter in Polyols
- ASTM-D4671 - Standard Test Method for Polyurethane Raw Materials: Determination of Unsaturation of Polyols
- ASTM-D4672 - Standard Test Method for Polyurethane Raw Materials: Determination of Water Content of Polyols
- ASTM-D4673 - Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
- ASTM-D4703 - Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
- ASTM-D4875 - Standard Test Methods of Polyurethane Raw Materials: Determination of the Polymerized Ethylene Oxide Content of Polyether Polyols
- ASTM-D4876 - Standard Test Method for Polyurethane Raw Materials Determination of Acidity of Crude or Modified Isocyanates (Withdrawn 2004)
- ASTM-D4878 - Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols
- ASTM-D4883 - Standard Test Method for Density of Polyethylene by the Ultrasound Technique
- ASTM-D4889 - Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates
- ASTM-D4890 - Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA (Platinum-Cobalt) Color of Polyols
- ASTM-D4894 - Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
- ASTM-D4976 - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
- ASTM-D5017 - Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance
- ASTM-D5155 - Standard Test Methods for Polyurethane Raw Materials: Determination of the Isocyanate Content of Aromatic Isocyanates
- ASTM-D5203 - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources (Withdrawn 2016)
- ASTM-D5204 - Standard Classification System and Basis for Specification for Polyamide-Imide (PAI) Molding and Extrusion Materials
- ASTM-D5205 - Standard Classification System and Basis for Specification for Polyetherimide (PEI) Molding and Extrusion Materials
- ASTM-D5227 - Standard Test Method for Measurement of Hexane Extractable Content of Polyolefins
- ASTM-D5260 - Standard Classification for Chemical Resistance of Poly(Vinyl Chloride) (PVC) Homopolymer and Copolymer Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
- ASTM-D5296 - Standard Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography
- ASTM-D5419 - Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures
- ASTM-D5422 - Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer
- ASTM-D5476 - Standard Classification System for Thermoplastic Polyurethane Materials (TPU) (Withdrawn 2005)
- ASTM-D5492 - Standard Test Method for Determination of Xylene Solubles in Propylene Plastics
- ASTM-D5499 - Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems
- ASTM-D5507 - Standard Test Method for Determination of Trace Organic Impurities in Monomer Grade Vinyl Chloride by Capillary Column/Multidimensional Gas Chromatography
- ASTM-D5523 - Standard Test Method for Polyurethane Raw Materials: Acidity by Argentometric Determination of Hydrolyzable Chlorine in Monomeric, Aromatic Isocyanates
- ASTM-D5524 - Standard Test Method for Determination of Phenolic Antioxidants in High Density Polyethylene Using Liquid Chromatography (Withdrawn 2009)
- ASTM-D5538 - Standard Practice for Thermoplastic Elastomers—Terminology and Abbreviations
- ASTM-D5575 - Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
- ASTM-D5576 - Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)
- ASTM-D5593 - Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005)
- ASTM-D5594 - Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR)
- ASTM-D5630 - Standard Test Method for Ash Content in Plastics
- ASTM-D5676 - Standard Specification for Recycled Polystyrene Molding and Extrusion Materials (Withdrawn 2004)
- ASTM-D569 - Method for Measuring the Flow Properties of Thermoplastic Molding Materials (Withdrawn 1995)
- ASTM-D5721 - Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
- ASTM-D5726 - Standard Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing
- ASTM-D5870 - Standard Practice for Calculating Property Retention Index of Plastics
- ASTM-D5897 - Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric Titration—Alternative Method
- ASTM-D5927 - Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods
- ASTM-D5930 - Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique
- ASTM-D5936 - Specification for Multipurpose Test Specimens (Withdrawn 1998)
- ASTM-D5937 - Standard Test Method for Determination of Tensile Properties and Test Conditions for Moulding and Extrusion Plastics (Withdrawn 1998)
- ASTM-D5939 - Standard Test Method for Injection Moulding of Test Specimens of Thermoplatic Materials (Withdrawn 1998)
- ASTM-D5940 - Standard Test Method for Injection Moulding of Test Specimens of Thermoplatic Materials-Plates (Withdrawn 1998)
- ASTM-D5998 - Standard Specification for Molded Polyethylene Shipping and Storage Drums
- ASTM-D6040 - Standard Guide to Standard Test Methods for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape
- ASTM-D6042 - Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Polypropylene Homopolymer Formulations Using Liquid Chromatography (LC)
- ASTM-D6070 - Standard Test Methods for Physical Properties of Smooth-Wall, Coilable, Polyethylene (PE) Conduit (Duct) for Preassembled Wire and Cable (Withdrawn 2016)
- ASTM-D6090 - Standard Test Method for Softening Point Resins (Mettler Cup and Ball Method)
- ASTM-D6150 - Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility
- ASTM-D6248 - Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry
- ASTM-D6261 - Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
- ASTM-D6263 - Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)
- ASTM-D6267 - Standard Test Method for Apparent Viscosity of Hydrocarbon Resins at Elevated Temperatures
- ASTM-D6314 - Standard Specification for Fluorocarbon Perfluoromethoxy (MFA) Resin Molding and Extrusion Materials (Withdrawn 2002)
- ASTM-D6338 - Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods
- ASTM-D6394 - Standard Classification System for and Basis for Specification for Sulfone Plastics (SP)
- ASTM-D6436 - Standard Guide for Reporting Properties for Plastics and Thermoplastic Elastomers
- ASTM-D6440 - Standard Terminology Relating to Hydrocarbon Resins
- ASTM-D6474 - Standard Test Method for Determining Molecular Weight Distribution and Molecular Weight Averages of Polyolefins by High Temperature Gel Permeation Chromatography
- ASTM-D6493 - Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus
- ASTM-D6579 - Standard Practice for Molecular Weight Averages and Molecular Weight Distribution of Hydrocarbon, Rosin and Terpene Resins by Size-Exclusion Chromatography
- ASTM-D6604 - Standard Practice for Glass Transition Temperatures of Hydrocarbon Resins by Differential Scanning Calorimetry
- ASTM-D6605 - Standard Practice for Determining the Color Stability of Hydrocarbon Resins After Heating
- ASTM-D6645 - Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry
- ASTM-D6713 - Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)
- ASTM-D6777 - Standard Test Method for Relative Rigidity of Poly(Vinyl Chloride)(PVC) Siding (Withdrawn 2021)
- ASTM-D6835 - Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)
- ASTM-D6865 - Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials
- ASTM-D6878 - Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing
- ASTM-D706 - Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
- ASTM-D707 - Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
- ASTM-D7083 - Standard Practice for Determination of Monomeric Plasticizers in Poly (Vinyl Chloride) (PVC) by Gas Chromatography
- ASTM-D7133 - Standard Test Method for Polyurethane Raw Materials: Instrumental Measurement of Tristimulus CIELAB Color and Yellowness Index of Liquids
- ASTM-D7253 - Standard Test Method for Polyurethane Raw Materials: Determination of Acidity as Acid Number for Polyether Polyols
- ASTM-D7293 - Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)
- ASTM-D7399 - Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR) (Withdrawn 2017)
- ASTM-D7436 - Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology
- ASTM-D7471 - Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials
- ASTM-D7472 - Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials
- ASTM-D7567 - Standard Test Method for Determining Gel Content in Crosslinked Ethylene Plastics Using Pressurized Liquid Extraction (Withdrawn 2015)
- ASTM-D7793 - Standard Specification for Insulated Vinyl Siding
- ASTM-D789 - Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
- ASTM-D8033 - Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
- ASTM-D8133 - Standard Test Method for Determination of Low Level Phthalates in Poly(Vinyl Chloride) Plastics by Solvent Extraction—Gas Chromatography/Mass Spectrometry
- ASTM-D8156 - Standard Classification System for and Basis of Specifications for Thermoplastic Elastomer Copolyester Molding and Extrusion Materials (TPC)
- ASTM-E2203 - Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
- ASTM-F1504 - Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation
- ASTM-F1515 - Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change
- ASTM-F1697 - Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit
- ASTM-F1698 - Standard Practice for Installation of Poly(Vinyl Chloride)(PVC) Profile Strip Liner and Cementitious Grout for Rehabilitation of Existing Man-Entry Sewers and Conduits
- ASTM-F1700 - Standard Specification for Solid Vinyl Floor Tile
- ASTM-F1701 - Standard Specification for Unused Rope with Special Electrical Properties
- ASTM-F1732 - Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material
- ASTM-F1735 - Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
- ASTM-F1741 - Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits
- ASTM-F1742 - Standard Specification for PVC Insulating Sheeting
- ASTM-F1759 - Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
- ASTM-F1803 - Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter
- ASTM-F1855 - Standard Specification for Polyoxymethylene (Acetal) for Medical Applications
- ASTM-F1867 - Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation
- ASTM-F1871 - Standard Specification for Folded/Formed Poly-(Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation
- ASTM-F1925 - Standard Specification for Semi-Crystalline Poly(lactide) Polymer and Copolymer Resins for Surgical Implants
- ASTM-F1947 - Standard Practice for Installation of Folded Poly (Vinyl Chloride) (PVC) Pipe into Existing Sewers and Conduits
- ASTM-F2778 - Standard Test Method for Measurement of Percent Crystallinity of Polyetheretherketone (PEEK) Polymers by Means of Specular Reflectance Fourier Transform Infrared Spectroscopy (R-FTIR)
- ASTM-F2848 - Standard Specification for Medical-Grade Ultra-High-Molecular-Weight Polyethylene Yarns
- ASTM-F2985 - Standard Practice for Installation of a PVC Segmental Panel Liner System in Man-Entry Size Sewers and Conduits (Withdrawn 2024)
- ASTM-F3034 - Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
- ASTM-F3181 - Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE
- ASTM-F443 - Specification for Bell-End Chlorinated Poly(Vinyl Chloride) (CPVC) Pipe Schedule 40 (Withdrawn 1987)
- ASTM-F500 - Specification for Self-Curing Acrylic Resins Used in Neurosurgery (Withdrawn 1993)
- ASTM-F624 - Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications
- ASTM-F639 - Standard Specification for Polyethylene Plastics for Medical Applications
- ASTM-F648 - Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants
- ASTM-F702 - Standard Specification for Polysulfone Resin for Medical Applications
- ASTM-F997 - Standard Specification for Polycarbonate Resin for Medical Applications
- ASTM-PS2 - Specification for Molding Plastics, Electrical, Thermoplastic (Withdrawn 1997)
BSI:
- BS-1493 - Method of specifying general purpose polystyrene (PS) moulding and extrusion materials
- BS-1524 - Specification for cellulose acetate moulding materials
- BS-2571 - Specification for general-purpose flexible PVC compounds for moulding and extrusion
- BS-2782-1 - Methods of Testing Plastics, Thermal Properties, Determination of the Burning Behaviou
- BS-2782-1-M-115A - Methods of testing plastics. Thermal properties
- BS-2782-1-M-130A - Methods of testing plastics. Thermal properties
- BS-2782-1-M-131B - Methods of testing plastics. Thermal properties
- BS-2782-1-M-132A - Methods of testing plastics. Thermal properties. Determination of resistance of decorative laminated sheet to dry heat
- BS-2782-1-M-134A & B - Methods of testing plastics. Thermal properties. Determination of the oxidation induction time of thermoplastics
- BS-2782-1-M-140D - Methods of testing plastics. Thermal properties
- BS-2782-1-M-150B - Method-150B: Determination of Cold Flex Temperature of Flexible Polyvinyl Compound
- BS-2782-1-M-150C - Methods of testing plastics. Thermal properties
- BS-2782-1-M-151A - Methods of testing plastics. Thermal properties. Determination of cold bend temperature of flexible polyvinyl chloride extrusion compound
- BS-2782-2-M-241A - Methods of testing plastics. Electrical properties. Determination of effect of polyvinyl chloride compound on the loss tangent of polyethylene
- BS-2782-3-M-327A - Methods of testing plastics. Mechanical properties
- BS-2782-4-M-434B - Methods of testing plastics. Chemical properties. Determination of antioxidants in polyolefin compounds by ultra-violet absorption of the chloroform extract
- BS-2782-4-M-434D - Methods of testing plastics. Chemical properties
- BS-2782-4-M-452B - Methods of testing plastics. Chemical properties
- BS-2782-4-M-452C - Methods of testing plastics. Chemical properties. Determination of butyl rubber content of low density polyethylene compounds
- BS-2782-4-M-452 D-F - Methods of testing plastics. Chemical properties
- BS-2782-4-M-453A - Methods of testing plastics. Chemical properties
- BS-2782-4-M-453C - Methods of testing plastics. Chemical properties
- BS-2782-4-M-454D - Method-454D: Determination of Volatile Matter (Including Water) of Pvc Resins
- BS-2782-4-M-470B - Methods of testing plastics. Chemical properties
- BS-2782-6-M-621D - Methods of testing plastics. Dimensional properties
- BS-2782-7-M-732D - Methods of testing plastics. Rheological properties
- BS-2782-8-M-823A & B - Methods of testing plastics. Other properties
- BS-2782-9-M-901A - Method-901a: Compression Moulding Test Specimens of Thermoplastic Materials
- BS-3126 - Method of specifying toughened polystyrene (SB) moulding and extrusion materials
- BS-3241 - Specification for toughened polystyrene for sheet extrusion
- BS-3412 - Methods of specifying general purpose polyethylene materials for moulding and extrusion
- BS-4840-2 - Rigid polyurethane (PUR) foam in slab form
- BS-4936 - Method of specifying styrene-acrylonitrile (SAN) moulding and extrusion materials
- BS-5139 - Method of specifying general purpose polypropylene and propylene copolymer materials for moulding and extrusion
- BS-5734-1 - Polyester moulding compounds for electrical and other purposes
- BS-5734-3 - Polyester Moulding Compounds for Electrical & Other Purposes, Specification for Dough
- BS-6564-3 - Polytetrafluoroethylene (PTFE) materials and products
- BS-7029-1 - Method of specifying thermoplastics injection mouldings
- BS-7029-2 - Method of specifying thermoplastics injection mouldings
- BS-89250 - Plastics - Joining of thermoplastic moulded components - Specification for quality levels for imperfections
- BS-EN-12099 - Plastics piping systems. Polyethylene piping materials and components. Determination of volatile content
- BS-EN-12814-4 - Testing of welded joints of thermoplastics semi-finished products
- BS-EN-13677-1 - Reinforced thermoplastic moulding compounds. Specification for GMT
- BS-EN-13677-2 - Reinforced thermoplastic moulding compounds. Specification for GMT
- BS-EN-13677-3 - Reinforced thermoplastic moulding compounds. Specification for GMT
- BS-EN-15342 - Plastics. Recycled plastics. Characterization of polystyrene (PS) recyclates
- BS-EN-15343 - Plastics. Recycled plastics. Plastics recycling traceability and assessment of conformity and recycled content
- BS-EN-15344 - Plastics. Recycled plastics. Characterization of Polyethylene (PE) recyclates
- BS-EN-15344-TC - Tracked Changes. Plastics. Recycled plastics. Characterization of Polyethylene (PE) recyclates
- BS-EN-15345 - Plastics. Recycled plastics. Characterization of polypropylene (PP) recyclates
- BS-EN-15346 - Plastics. Recycled plastics. Characterization of poly(vinyl chloride) (PVC) recyclates
- BS-EN-15346-TC - Tracked Changes. Plastics. Recycled plastics. Characterization of poly(vinyl chloride) (PVC) recyclates
- BS-EN-15348 - Plastics. Recycled plastics. Characterization of poly(ethylene terephthalate) (PET) recyclates
- BS-EN-15348-TC - Tracked Changes. Plastics. Recycled plastics. Characterization of poly(ethylene terephthalate) (PET) recyclates
- BS-EN-15860 - Plastics. Thermoplastic semi-finished products for machining. Requirements and test methods
- BS-EN-15860-TC - Tracked Changes. Plastics. Thermoplastic semi-finished products for machining. Requirements and test methods
- BS-EN-16980-1 - Photocatalysis. Continuous flow test methods
- BS-EN-17271 - Plastics. Poly(vinyl chloride) (PVC) based profiles. Determination of the peel strength of profiles laminated with foils
- BS-EN-1778 - Characteristic values for welded thermoplastics constructions. Determination of allowable stresses and moduli for design of thermoplastics equipment
- BS-EN-478-TC - Tracked Changes. Plastics. Poly(vinyl chloride) (PVC) based profiles. Determination of the appearance after exposure at 150°C
- BS-EN-479-TC - Tracked Changes. Plastics. Poly(vinyl chloride) (PVC) based profiles. Determination of heat reversion
- BS-EN-513-TC - Tracked Changes. Plastics. Poly(vinyl chloride) (PVC) based profiles. Determination of the resistance to artificial weathering
- BS-EN-ISO-10350-1 - Plastics. Acquisition and presentation of comparable single-point data
- BS-EN-ISO-10366-1 - Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-10366-2 - Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials
- BS-EN-ISO-1061 - Plastics. Unplasticized cellulose acetate. Determination of free acidity
- BS-EN-ISO-1133 - Plastics. Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
- BS-EN-ISO-1133-1 - Plastics. Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics
- BS-EN-ISO-1133-2 - Plastics. Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics
- BS-EN-ISO-11337 - Plastics. Polyamides. Determination of -caprolactam and -laurolactam by gas chromatography
- BS-EN-ISO-11337-TC - Tracked Changes. Plastics. Polyamides. Determination of -caprolactam and -laurolactam by gas chromatography
- BS-EN-ISO-11468 - Plastics. Preparation of PVC pastes for test purposes. Dissolver method
- BS-EN-ISO-11542-1 - Plastics. Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials
- BS-EN-ISO-11542-2 - Plastics. Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials
- BS-EN-ISO-1157 - Plastics. Cellulose acetate in dilute solution. Determination of viscosity number and viscosity ratio
- BS-EN-ISO-1163-1 - Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials
- BS-EN-ISO-1163-2 - Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials
- BS-EN-ISO-12086-1 - Plastics. Fluoropolymer dispersions and moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-12086-2 - Plastics. Fluoropolymer dispersions and moulding and extrusion materials. Preparation of test specimens and determination of properties
- BS-EN-ISO-1264 - Plastics. Homopolymer and copolymer resins of vinyl chloride. Determination of pH of aqueous extract
- BS-EN-ISO-1265 - Plastics. Poly(vinyl chloride) resins. Determination of number of impurities and foreign particles
- BS-EN-ISO-1269 - Plastics. Homopolymer and copolymer resins of vinyl chloride. Determination of volatile matter (including water)
- BS-EN-ISO-14632-TC - Tracked Changes. Extruded sheets of polyethylene (PE-HD). Requirements and test methods
- BS-EN-ISO-14663-1 - Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials
- BS-EN-ISO-14663-2 - Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials
- BS-EN-ISO-14896 - Plastics. Polyurethane raw materials. Determination of isocyanate content
- BS-EN-ISO-14910-1 - Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion
- BS-EN-ISO-14910-2 - Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion. Preparation of test specimens and determination of properties
- BS-EN-ISO-15023-1 - Plastics. Poly(vinyl alcohol) (PVAL) materials
- BS-EN-ISO-15023-2 - Plastics. Poly(vinyl alcohol) (PVAL) materials
- BS-EN-ISO-15103-1 - Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-15103-2 - Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials
- BS-EN-ISO-15526-1 - Plastics. Polyketone (PK) moulding and extrusion materials
- BS-EN-ISO-15526-2 - Plastics. Polyketone (PK) moulding and extrusion materials. Preparation of test specimens and determination of properties
- BS-EN-ISO-1597 - Plastics - Unplasticized Cellulose Acetate - Determination of Acetic Acid Yield
- BS-EN-ISO-1598 - Plastics. Cellulose acetate. Determination of insoluble particles
- BS-EN-ISO-1622-1 - Plastics. Polystyrene (PS) moulding and extrusion materials
- BS-EN-ISO-1622-2 - Plastics. Polystrene (PS) moulding and extrusion materials
- BS-EN-ISO-1624 - Plastics. Vinyl chloride homopolymer and copolymer resins. Sieve analysis in water
- BS-EN-ISO-1628-2 - Plastics. Determination of the viscosity of polymers in dilute solution using capillary viscometers
- BS-EN-ISO-1628-3 - Plastics. Determination of the viscosity of polymers in dilute solution using capillary viscometers
- BS-EN-ISO-1628-5 - Plastics. Determination of the viscosity of polymers in dilute solution using capillary viscometers. Thermoplastic polyester (TP) homopolymers and copolymers
- BS-EN-ISO-16396-1 - Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-16396-1-TC - Tracked Changes. Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-16396-2 - Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-16396-2-TC - Tracked Changes. Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-17855-1 - Plastics. Polyethylene (PE) moulding and extrusion materials
- BS-EN-ISO-17855-2 - Plastics. Polyethylene (PE) moulding and extrusion materials
- BS-EN-ISO-17855-2-TC - Tracked Changes. Plastics. Polyethylene (PE) moulding and extrusion materials
- BS-EN-ISO-18064 - Thermoplastic elastomers. Nomenclature and abbreviated terms
- BS-EN-ISO-182-2 - Plastics. Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
- BS-EN-ISO-182-3 - Plastics. Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
- BS-EN-ISO-182-3-TC - Tracked Changes. Plastics. Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
- BS-EN-ISO-182-4 - Plastics. Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
- BS-EN-ISO-1872-1 - Polyethylene (PE) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-1872-2 - Plastics. Polyethylene (PE) moulding and extrusion materials
- BS-EN-ISO-1873-1 - Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-1873-2 - Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-1874-1 - Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-1874-2 - Plastics. Polyamide (PA) moulding and extrusion materials
- BS-EN-ISO-19062-1 - Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials
- BS-EN-ISO-19062-2 - Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials
- BS-EN-ISO-19063-1 - Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials
- BS-EN-ISO-19063-1-TC - Tracked Changes. Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials
- BS-EN-ISO-19063-2 - Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials
- BS-EN-ISO-19064-2 - Plastics. Styrene-acrylonitrile (SAN) moulding and extrusion materials
- BS-EN-ISO-19065-1 - Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials
- BS-EN-ISO-19065-2 - Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials
- BS-EN-ISO-19066-1 - Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials
- BS-EN-ISO-19066-2 - Plastics. Methyl methacrylate-acrylonitrile-butadienestyrene (MABS) moulding and extrusion materials
- BS-EN-ISO-19069-1 - Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-19069-1-TC - Tracked Changes. Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-19069-2 - Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-19069-2-TC - Tracked Changes. Plastics. Polypropylene (PP) moulding and extrusion materials
- BS-EN-ISO-19892 - Plastics piping systems. Thermoplastics pipes and fittings for hot and cold water. Test method for the resistance of joints to pressure cycling
- BS-EN-ISO-20028-1 - Plastics. Thermoplastic polyester (TP) moulding and extrusion materials
- BS-EN-ISO-20029-1 - Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion
- BS-EN-ISO-20029-2 - Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion
- BS-EN-ISO-20557-1 - Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials
- BS-EN-ISO-20557-2 - Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials
- BS-EN-ISO-20568-1 - Plastics. Fluoropolymer dispersions and moulding and extrusion materials
- BS-EN-ISO-20568-2 - Plastics. Fluoropolymer dispersions and moulding and extrusion materials
- BS-EN-ISO-20568-2-TC - Tracked Changes. Plastics. Fluoropolymer dispersions and moulding and extrusion materials
- BS-EN-ISO-21301-1 - Plastics. Ethylene-vinyl acetate (EVAC) moulding and extrusion materials
- BS-EN-ISO-21301-2 - Plastics. Polybutene-1 (PB-1) moulding and extrusion materials
- BS-EN-ISO-21302-1 - Plastics. Polybutene-1 (PB-1) moulding and extrusion materials
- BS-EN-ISO-21302-2 - Plastics. Polybutene-1 (PB-1) moulding and extrusion materials
- BS-EN-ISO-21304-1 - Plastics. Ultra-high-molecular-weight polyethylene (PE- UHMW) moulding and extrusion materials
- BS-EN-ISO-21304-2 - Plastics. Ultra-high-molecular-weight polyethylene (PE- UHMW) moulding and extrusion materials
- BS-EN-ISO-21305-1 - Plastics. Polycarbonate (PC) moulding and extrusion materials
- BS-EN-ISO-21305-2 - Plastics. Polycarbonate (PC) moulding and extrusion materials
- BS-EN-ISO-21306-2 - Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials
- BS-EN-ISO-21309-1 - Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials
- BS-EN-ISO-21309-2 - Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials
- BS-EN-ISO-21970-1 - Plastics. Polyketone (PK) moulding and extrusion materials
- BS-EN-ISO-21970-2 - Plastics. Polyketone (PK) moulding and extrusion materials
- BS-EN-ISO-23153-1 - Plastics. Polyetheretherketone (PEEK) moulding and extrusion materials
- BS-EN-ISO-23153-2 - Plastics. Polyetheretherketone (PEEK) moulding and extrusion materials
- BS-EN-ISO-24022-1 - Plastics. Polystyrene (PS) moulding and extrusion materials
- BS-EN-ISO-24022-2 - Plastics. Polystyrene (PS) moulding and extrusion materials
- BS-EN-ISO-24023-1 - Plastics. Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials
- BS-EN-ISO-24023-2 - Plastics. Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials
- BS-EN-ISO-24024-1 - Plastics. Homopolymer and copolymer resins of vinyl chloride
- BS-EN-ISO-24024-1-TC - Tracked Changes. Plastics. Homopolymer and copolymer resins of vinyl chloride
- BS-EN-ISO-24024-2 - Plastics. Homopolymer and copolymer resins of vinyl chloride
- BS-EN-ISO-24024-2-TC - Tracked Changes. Plastics. Homopolymer and copolymer resins of vinyl chloride
- BS-EN-ISO-24025-1 - Plastics. Sulfone polymer moulding and extrusion materials
- BS-EN-ISO-24025-2 - Plastics. Sulfone polymer moulding and extrusion materials
- BS-EN-ISO-24026-1 - Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials
- BS-EN-ISO-24026-2 - Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials
- BS-EN-ISO-25137-1 - Plastics. Sulfone polymer moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-25137-2 - Plastics. Sulfone polymer moulding and extrusion materials. Preparation of test specimens and determination of properties
- BS-EN-ISO-2580-1 - Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-2580-2 - Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials
- BS-EN-ISO-28941-1 - Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-2897-1 - Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials
- BS-EN-ISO-2898-1 - Plastics. Plasticized poly (vinyl chloride) (PVC-P) moulding and extrusion materials
- BS-EN-ISO-2898-2 - Plastics. Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials
- BS-EN-ISO-293 - Plastics. Compression moulding of test specimens of thermoplastic materials
- BS-EN-ISO-293-TC - Tracked Changes. Plastics. Compression moulding of test specimens of thermoplastic materials
- BS-EN-ISO-294-1 - Plastics. Injection moulding of test specimens of thermoplastic materials
- BS-EN-ISO-294-1-TC - Tracked Changes. Plastics. Injection moulding of test specimens of thermoplastic materials
- BS-EN-ISO-294-2 - Plastics. Injection moulding of test specimens of thermoplastic materials
- BS-EN-ISO-294-4 - Plastics. Injection moulding of test specimens of thermoplastic materials
- BS-EN-ISO-294-5 - Plastics. Injection moulding of test specimens of thermoplastic materials
- BS-EN-ISO-29988-1 - Plastics. Polyoxymethylene (POM) moulding and extrusion materials
- BS-EN-ISO-29988-2 - Plastics. Polyoxymethylene (POM) moulding and extrusion materials
- BS-EN-ISO-29988-2-TC - Tracked Changes. Plastics. Polyoxymethylene (POM) moulding and extrusion materials
- BS-EN-ISO-305 - Plastics. Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds. Discoloration method
- BS-EN-ISO-306 - Plastics. Thermoplastic materials. Determination of Vicat softening temperature (VST)
- BS-EN-ISO-306-TC - Tracked Changes. Plastics. Thermoplastic materials. Determination of Vicat softening temperature (VST)
- BS-EN-ISO-307 - Plastics. Polyamides. Determination of viscosity number
- BS-EN-ISO-3451-4 - Plastics. Determination of ash
- BS-EN-ISO-3451-4-TC - Tracked Changes. Plastics. Determination of ash
- BS-EN-ISO-3451-5 - Plastics. Determination of ash
- BS-EN-ISO-4577 - Plastics. Polypropylene and propylene-copolymers. Determination of thermal oxidative stability in air. Oven method
- BS-EN-ISO-4610 - Plastics. Vinyl chloride homopolymer and copolymer resins. Sieve analysis using air-jet sieve apparatus
- BS-EN-ISO-4612 - Plastics. Preparation of PVC pastes for test purposes. Planetary-mixer method
- BS-EN-ISO-4613-1 - Plastics. Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials
- BS-EN-ISO-4894-1 - Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials
- BS-EN-ISO-4894-2 - Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials
- BS-EN-ISO-6401 - Plastics. Poly(vinyl chloride). Determination of residual vinyl chloride monomer using gas-chromatographic method
- BS-EN-ISO-6401-TC - Tracked Changes. Plastics. Poly(vinyl chloride). Determination of residual vinyl chloride monomer using gas-chromatographic method
- BS-EN-ISO-6402-1 - Plastics. Impact resistant acrylonitrile/styrene moulding and extrusion materials (ASA, AES, ACS), excluding butadiene-modified materials. Designation system and basis for specifications
- BS-EN-ISO-7391-1 - Plastics. Polycarbonate (PC) moulding and extrusion materials
- BS-EN-ISO-7391-2 - Plastics. Polycarbonate (PC) moulding and extrusion materials
- BS-EN-ISO-7792-1 - Plastics. Thermoplastic polyester (TP) moulding and extrusion materials
- BS-EN-ISO-7792-2 - Plastics. Thermoplastic polyester (TP) moulding and extrusion materials
- BS-EN-ISO-8257-1 - Plastics. Poly(methyl methacrylate)(PMMA) moulding and extrusion materials
- BS-EN-ISO-8257-2 - Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials
- BS-EN-ISO-8985-TC - Tracked Changes. Plastics. Ethylene/vinyl acetate copolymer (EVAC) thermoplastics. Determination of vinyl acetate content
- BS-EN-ISO-8986-1 - Plastics. Polybutene-1 (PB-1) moulding and extrusion materials
- BS-EN-ISO-8986-2 - Plastics. Polybutene-1 (PB-1) moulding and extrusion materials
- BS-EN-ISO-960 - Plastics. Polyamides (PA). Determination of water content
- BS-EN-ISO-9988-1 - Plastics. Polyoxymethylene (POM) moulding and extrusion materials. Designation system and basis for specifications
- BS-EN-ISO-9988-2 - Plastics. Polyoxymethylene (POM) moulding and extrusion materials. Preparation of test specimens and determination of properties
- BS-ISO-12418-1 - Plastics. Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates
- BS-ISO-12418-2 - Plastics. Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates
- BS-ISO-14898 - Plastics. Aromatic isocyanates for use in the production of polyurethane. Determination of acidity
- BS-ISO-15023-1 - Designation System and Basis for Specifications
- BS-ISO-15373 - Plastics. Polymer dispersions. Determination of free formaldehyde
- BS-ISO-16365-1 - Plastics. Thermoplastic polyurethanes for moulding and extrusion
- BS-ISO-16365-2 - Plastics. Thermoplastic polyurethanes for moulding and extrusion
- BS-ISO-16365-3 - Plastics. Thermoplastic polyurethanes for moulding and extrusion
- BS-ISO-16770 - Plastics. Determination of environmental stress cracking (ESC) of polyethylene. Full-notch creep test (FNCT)
- BS-ISO-16790 - Plastics. Determination of drawing characteristics of thermoplastics in the molten state
- BS-ISO-16790-TC - Tracked Changes. Plastics. Determination of drawing characteristics of thermoplastics in the molten state
- BS-ISO-18263-1 - Plastics. Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging
- BS-ISO-20558-1 - Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials
- BS-ISO-20558-2 - Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials
- BS-ISO-22498 - Plastics. Vinyl chloride homopolymer and copolymer resins. Particle size determination by mechanical sieving
- BS-ISO-23512 - Plastics. Joining of thermoplastic moulded components. Specification of variables for thermal joining processes
- BS-ISO-24076 - Plastics. Polypropylene (PP). Determination of isotactic index by low-resolution nuclear magnetic resonance spectrometry
- BS-ISO-24538 - Plastics. Homopolymer and copolymer resins of vinyl chloride. Determination of residual vinyl chloride monomer by gas-chromatographic analysis of dry powder
- BS-ISO-2561 - Plastics. Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
- BS-ISO-2561-TC - Tracked Changes. Plastics. Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography.
- BS-ISO-28078-1 - Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials
- BS-ISO-28078-2 - Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials
- BS-ISO-2897-1 - Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials
- BS-ISO-294-5 - Plastics. Injection moulding of test specimens of thermoplastic materials. Preparation of standard specimens for investigating anisotropy
- BS-ISO-4504 - Plastics. Polyethylene (PE). Determination of co-monomer content by solution state 13C-NMR spectrometry
- BS-ISO-4574 - Plastics. PVC resins for general use. Determination of hot plasticizer absorption
- BS-ISO-4575 - Plastics. Poly(vinyl chloride) pastes. Determination of apparent viscosity using the Severs rheometer
- BS-ISO-4894-1 - Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials
- BS-ISO-5623 - Plastics. Joining of thermoplastic moulded components. Specification for quality levels for imperfections
- BS-ISO-5623-TC - Tracked Changes. Plastics. Joining of thermoplastic moulded components. Specification for quality levels for imperfections
- BS-ISO-6402-1 - Plastics. Impact resistant acrylonitrile/styrene moulding and extrusion materials (ASA, AES, ACS), excluding butadiene-modified materials. Designation
- BS-ISO-6691 - Thermoplastic polymers for plain bearings. Classification and designation
- BS-ISO-8257-2 - Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials
- BS-ISO-9113 - Plastics. Polypropylene (PP) and propylene-copolymer thermoplastics. Determination of isotactic index
- BS-ISO-9988-1 - Plastics, Polyoxymethylene (Pom) Moulding & Extrusion Materials, Designation System &
- BS-ISO-9988-2 - Plastics. Polyoxymethylene (POM) moulding and extrusion materials. Preparation of test specimens and determination of properties
- PD-CEN-16861 - Plastics. Recycled plastics. Determination of selected marker compounds in food grade recycled polyethylene terephthalate (PET)
ISO:
- ISO-10350-1 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
- ISO-10350-1-AM1 - - Amendment 1
- ISO-10366-1 - Plastics -- Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials -- Part 1: Designation system and basis for specifications (available in English only
- ISO-10366-2 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1060-1 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications
- ISO-1060-2 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties
- ISO-1061 - Plastics - Unplasticized cellulose acetate - Determination of free acidity
- ISO-1068 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of compacted apparent bulk density
- ISO-1110 - Plastics - Polyamides - Accelerated conditioning of test specimens
- ISO-1133 - Plastics -- Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
- ISO-1133-1 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method
- ISO-1133-2 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture
- ISO-11337 - Plastics - Polyamides - Determination of -caprolactam and -laurolactam by gas chromatography
- ISO-11468 - Plastics - Preparation of PVC pastes for test purposes - Dissolver method
- ISO-11542-1 - Plastics -- Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials -- Part 1: Designation system and basis for specifications
- ISO-11542-2 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1157 - Plastics -- Cellulose acetate in dilute solution -- Determination of viscosity number and viscosity ratio
- ISO-1158 - Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content
- ISO-1159 - Plastics -- Vinyl chloride-vinyl acetate copolymers -- Determination of vinyl acetate
- ISO-1163-1 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-1163-2 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-12000 - Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Definitions and review of test methods
- ISO-12086-1 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-12086-2 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-12418-1 - Plastics - Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates - Part 1: Designation system and basis for specifications
- ISO-12418-2 - Plastics - Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates - Part 2: Preparation of test specimens and determination of properties
- ISO-1264 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract
- ISO-1265 - Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles
- ISO-1269 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water)
- ISO-14446 - Binders for paints and varnishes -- Determination of the viscosity of industrial cellulose nitrate solutions and classification of such solutions
- ISO-14663-1 - Plastics -- Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials -- Part 1: Designation system and basis for specifications
- ISO-14663-2 - Plastics -- Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
- ISO-14910-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification
- ISO-14910-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties
- ISO-15023-1 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 1: Designation system and basis for specifications
- ISO-15023-2 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 2: Determination of properties
- ISO-15103-1 - Plastics -- Poly(phenylene ether) (PPE) moulding and extrusion materials -- Part 1: Designation system and basis for specifications
- ISO-15103-2 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-15373 - Plastics - Polymer dispersions - Determination of free formaldehyde
- ISO-15526-1 - Plastics -- Polyketone (PK) moulding and extrusion materials -- Part 1: Designation system and basis for specifications
- ISO-15526-2 - Plastics -- Polyketone (PK) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
- ISO-15853 - Thermoplastics materials -- Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding
- ISO-1598 - Plastics - Cellulose acetate - Determination of insoluble particles
- ISO-1599 - Plastics - Cellulose acetate - Determination of viscosity loss on moulding
- ISO-1600 - Plastics - Cellulose acetate - Determination of light absorption on moulded specimens produced using different periods of heating
- ISO-1622-1 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-1622-2 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1624 - Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water
- ISO-1628-2 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride) resins
- ISO-1628-3 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes
- ISO-1628-4 - Plastics -- Determination of the viscosity of polymers in dilute solution using capillary viscometers -- Part 4: Polycarbonate (PC) moulding and extrusion materials
- ISO-1628-6 - Plastics - Determination of viscosity number and limiting viscosity number - Part 6: Methyl methacrylate polymers
- ISO-16365-1 - Plastics - Thermoplastic polyurethanes for moulding and extrusion - Part 1: Designation system and basis for specifications
- ISO-16365-2 - Plastics - Thermoplastic polyurethanes for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties
- ISO-16365-3 - Plastics - Thermoplastic polyurethanes for moulding and extrusion - Part 3: Distinction between ether and ester polyurethanes by determination of the ester group content
- ISO-16396-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-16396-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-16770 - Plastics - Determination of environmental stress cracking (ESC) of polyethylene - Full-notch creep test (FNCT)
- ISO-16790 - Plastics - Determination of drawing characteristics of thermoplastics in the molten state
- ISO-17855-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-17855-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms
- ISO-182-1 - Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 1: Congo red method
- ISO-182-2 - Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 2: pH method
- ISO-182-3 - Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 3: Conductometric method
- ISO-182-4 - Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 4: Potentiometric method
- ISO-18263-1 - Plastics - Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging - Part 1: Designation system and basis for specification
- ISO-18263-2 - Plastics - Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging - Part 2: Preparation of test specimens and determination of properties
- ISO-1872-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-1872-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1872-2-1 - AMENDMENT 1
- ISO-1873-1 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-1873-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1873-2-1 - AMENDMENT 1
- ISO-1874-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specification
- ISO-1874-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-1874-2-AM1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of propertiesAmendment 1: Laser sintering of specimens
- ISO-1875 - Plastics - Plasticized cellulose acetate - Determination of matter extractable by diethyl ether
- ISO-19062-1 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19062-2 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19063-1 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19063-2 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19064-1 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19064-2 - Plastics - Styrene-acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19065-1 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19065-2 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19066-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19066-2 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19069-1 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-19069-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-19892 - Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling
- ISO-20028-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specification
- ISO-20028-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-20029-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification
- ISO-20029-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties
- ISO-20557-1 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-20557-2 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties
- ISO-20558-1 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-20558-2 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties
- ISO-20568-1 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-20568-2 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21301-1 - Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21301-2 - Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21302-1 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21302-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21304-1 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21304-2 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21305-1 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specification
- ISO-21305-2 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21306-1 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21306-2 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21309-1 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21309-2 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-21970-1 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-21970-2 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-22498 - Plastics - Vinyl chloride homopolymer and copolymer resins - Particle size determination by mechanical sieving
- ISO-23153-1 - Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-23153-2 - Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-23512 - Plastics - Joining of thermoplastic moulded components - Specification of variables for thermal joining processes
- ISO-24022-1 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-24022-2 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-24023-1 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-24023-2 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-24024-1 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications
- ISO-24024-2 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties
- ISO-24025-1 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-24025-2 - Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-24026-1 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-24026-2 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-24047 - Plastics - Polyethylene (PE) and polypropylene (PP) thermoplastics - Determination of metal content by ICP-OES
- ISO-24048 - Plastics - Determination of bound acrylonitrile content in the continuous phase of acrylonitrile-butadiene-styrene (ABS) by Dumas combustion method
- ISO-24076 - Plastics - Polypropylene (PP) - Determination of isotactic index by low-resolution nuclear magnetic resonance spectrometry
- ISO-24538 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of residual vinyl chloride monomer by gas-chromatographic analysis of dry powder
- ISO-25137-1 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-25137-2 - Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-2561 - Plastics - Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
- ISO-2580-1 - Plastics -- Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials -- Part 1: Designation system and basis for specifications (available in English only)
- ISO-2580-2 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-27547-1 - Plastics - Preparation of test specimens of thermoplastic materials using mouldless technologies - Part 1: General principles, and laser sintering of test specimens
- ISO-28078-1 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-28078-2 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-28941-1 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-2897-1 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-2897-2 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-2898-1 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-2898-2 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-293 - Plastics - Compression moulding of test specimens of thermoplastic materials
- ISO-294-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
- ISO-294-1-1 - Amendment 1
- ISO-294-1-2 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens - Amendment 2: Methods of determining the hold pressure and hold time
- ISO-294-2 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars
- ISO-294-2-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars - Amendment 1
- ISO-294-3 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates
- ISO-294-3-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates - Amendment 1
- ISO-294-4 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage
- ISO-294-5 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy
- ISO-294-5-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropyAmendment 1
- ISO-29988-1 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-29988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-305 - Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds - Discoloration method
- ISO-306 - Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)
- ISO-307 - Plastics - Polyamides - Determination of viscosity number
- ISO-307-AM1 - - Amendment 1: Corrections, and update to reference to JIS K 6920-2
- ISO-3451-2 - Plastics - Determination of ash - Part 2: Poly(alkylene terephthalate) materials
- ISO-3451-3 - Plastics - Determination of ash - Part 3 : Unplasticized cellulose acetate
- ISO-3451-4 - Plastics - Determination of ash - Part 4: Polyamides
- ISO-3451-5 - Plastics - Determination of ash - Part 5: Poly(vinyl chloride)
- ISO-4504 - Plastics - Polyethylene (PE) - Determination of co-monomer content by solution state 13C-NMR spectrometry
- ISO-4574 - Plastics - PVC resins for general use - Determination of hot plasticizer absorption
- ISO-4575 - Plastics - Poly(vinyl chloride) pastes - Determination of apparent viscosity using the Severs rheometer
- ISO-4577 - Plastics - Polypropylene and propylene-copolymers - Determination of thermal oxidative stability in air - Oven method
- ISO-4581 - Plastics - Styrene/acrylonitrile copolymers - Determination of residual acrylonitrile monomer content - Gas chromatography method
- ISO-458-2 - Plastics - Determination of stiffness in torsion of flexible materials - Part 2 : Application to plasticized compounds of homopolymers and copolymers of vinyl chloride
- ISO-4608 - Plastics - Homopolymer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature
- ISO-4610 - Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus
- ISO-4612 - Plastics - Preparation of PVC pastes for test purposes - Planetary-mixer method
- ISO-4613-1 - Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 1: Designation and specification
- ISO-4613-2 - Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-4613-2-1 - Plastics - Ethylene/vinyl acetate copolymer (E/VAC) thermoplastics - Part 2: Preparation of test specimens and determination of properties - Amendment 1
- ISO-4894-1 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-4894-2 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-585 - Plastics - Unplasticized cellulose acetate - Determination of moisture content
- ISO-6186 - Plastics - Determination of pourability
- ISO-6401 - Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer using gas-chromatographic method
- ISO-6402-1 - Plastics -- Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials -- Part 1: Designation system and basis for specifications (available in English only)
- ISO-6402-2 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-6691 - Thermoplastic polymers for plain bearings - Classification and designation
- ISO-7391-1 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-7391-2 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-7792-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-7792-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-8257-1 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-8257-2 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-8985 - Plastics - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content
- ISO-8986-1 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-8986-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO-8986-2-1 - AMENDMENT 1
- ISO-9113 - Plastics - Polypropylene (PP) and propylene-copolymer thermoplastics - Determination of isotactic index
- ISO-9988-1 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO-9988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- ISO/DIS-8986-2 - Part 2: Preparation of Test Specimens and Determination of Properties, Plastics - Polybu
Other SDOs:
- BS-EN-ISO-20028-2 - Plastics. Thermoplastic polyester (TP) moulding and extrusion materials
- BS-ISO-24047 - Plastics. Polyethylene (PE) and polypropylene (PP) thermoplastics. Determination of metal content by ICP-OES
- DIN-482 - Natural stone kerbs
- DIN-EN-15334 - Sanitary Appliances - Methacrylic Dispersions of High Filler Content
- DIN-EN-ISO-10366-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- DIN-EN-ISO-10366-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Methyl
- DIN-EN-ISO-1133 - Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005)
- DIN-EN-ISO-11337 - Plastics - Polyamides - Determination of E-Caprolactam & W-Laurolactam by Gas Chromato
- DIN-EN-ISO-12086-1 - Part 1: Designation System and Basis for Specifications, Plastics - Fluoropolymer Disper
- DIN-EN-ISO-12086-2 - Part 2: Preparation of Test Specimens and Determination of Properties, Plastics - Fluoro
- DIN-EN-ISO-1265 - Plastics - Poly(Vinyl Chloride) Resins - Determination of Number of Impurities & Forei
- DIN-EN-ISO-1269 - Plastics - Homopolymer & Copolymer Resins of Vinyl Chloride - Determination of Volati
- DIN-EN-ISO-14663-1 - Part 1: Designation System and Basis for Specifications, Plastics - Ethylene/Vinyl Alcoh
- DIN-EN-ISO-14663-2 - Part 2: Preparation of Test Specimens and Determination of Properties, Plastics - Ethyle
- DIN-EN-ISO-14896 - Plastics - Polyurethane Raw Materials - Determination of Isocyanate Content
- DIN-EN-ISO-14910-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specifications (ISO 14910-1:2013)
- DIN-EN-ISO-14910-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013)
- DIN-EN-ISO-15023-1 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 1: Designation system and basis for specifications
- DIN-EN-ISO-15023-2 - Part 2: Determination of Properties, Plastics - Poly(Vinyl Alcohol) (Pval) Materials
- DIN-EN-ISO-15103-1 - Part 1: Designation System & Basis for Specifications, Plastics, Poly(Phenylene Ether)
- DIN-EN-ISO-15103-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Poly(Ph
- DIN-EN-ISO-15526-1 - Part 1: Designation System & Basis for Specifications, Plastics, Polyketone (Pk) Mould
- DIN-EN-ISO-15526-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Polyket
- DIN-EN-ISO-1628-3 - Part 3: Polyethylenes & Polypropylenes, Plastics - Determination of the Viscosity of P
- DIN-EN-ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms
- DIN-EN-ISO-1872-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- DIN-EN-ISO-1874-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
- DIN-EN-ISO-2580-1 - Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- DIN-EN-ISO-2580-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Acrylon
- DIN-EN-ISO-2897-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Impact-
- DIN-EN-ISO-293 - Plastics, Compression Moulding of Test Specimens of Thermoplastic Materials
- DIN-EN-ISO-294-2 - Part 2: Small Tensile Bars, Plastics - Injection Moulding of Test Specimens of Thermop
- DIN-EN-ISO-294-3 - Part 3: Small Plates, Plastics, Injection Moulding of Test Specimens of Thermoplastic
- DIN-EN-ISO-294-4 - Part 4: Determination of Moulding Shrinkage, Plastics, Injection Moulding of Test Spec
- DIN-EN-ISO-306 - Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013)
- DIN-EN-ISO-307 - Plastics - Polyamides - Determination of viscosity number (ISO 307:2007 + Amd 1:2013)
- DIN-EN-ISO-3451-5 - Part 5: Poly(Vinyl Chloride), Plastics - Determination of Ash
- DIN-EN-ISO-4613-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Ethylen
- DIN-EN-ISO-6401 - Plastics - Poly(Vinyl Chloride) - Determination of Residual Vinyl Chloride Monomer -
- DIN-EN-ISO-6402-1 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specification
- DIN-EN-ISO-6402-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Acrylon
- DIN-EN-ISO-7391-1 - Part 1: Designation System & Basis for Specifications, Plastics - Polycarbonate (Pc) M
- DIN-EN-ISO-7391-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Polyca
- DIN-EN-ISO-7792-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7792-1:2012)
- DIN-EN-ISO-7792-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012)
- DIN-EN-ISO-8257-1 - Part 1: Designation System & Basis for Specifications, Plastics - Poly(Methyl Methacry
- DIN-EN-ISO-8257-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Poly(m
- DIN-EN-ISO-9988-1 - Part 1: Designation System & Basis for Specifications, Plastics - Polyoxymethylene (Po
- DIN-ISO-5834-1 - Part 1: Powder Form, Implants for Surgery - Ultra-High Molecular-Weight Polyethylene
- EN-12099 - Plastics Piping Systems, Polyethylene Piping Materials & Components, Determination Of
- EN-12814-4 - Part 4: Peel Test, Testing of Welded Joints of Thermoplastics Semi-Finished Products
- EN-15342 - Plastics, Recycled Plastics, Characterization of Polystyrene (Ps) Recyclates
- EN-15343 - Plastics, Recycled Plastics, Plastics Recycling Traceability & Assessment of Conformit
- EN-15344 - Plastics, Recycled Plastics, Characterization of Polyethylene (Pe) Recyclates
- EN-15345 - Plastics, Recycled Plastics, Characterization of Polypropylene (Pp) Recyclates
- EN-15346 - Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
- EN-15348 - Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates
- EN-15860 - Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods
- EN-17271 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the peel strength of profiles laminated with foils
- EN-1778 - Characteristic Values for Welded Thermoplastics Constructions, Determination of Allowa
- EN-ISO-10350-1 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
- EN-ISO-1133 - Plastics, Determination of the Melt Mass-Flow Rate (Mfr) & the Melt Volume-Flow Rate
- EN-ISO-1133-1 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
- EN-ISO-1133-2 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
- EN-ISO-11337 - Plastics - Polyamides - Determination of E-Caprolactam & W-Laurolactam by Gas Chromato
- EN-ISO-11468 - Plastics, Preparation of Pvc Pastes for Test Purposes, Dissolver Method
- EN-ISO-11542-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Ultra-
- EN-ISO-1163-1 - Part 1: Designation System & Basis for Specifications, Unplasticized Poly(Vinyl Chlori
- EN-ISO-12086-1 - Part 1: Designation System & Basis for Specifications, Plastics - Fluoropolymer Disper
- EN-ISO-12086-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Fluoro
- EN-ISO-1264 - Plastics, Homopolymer & Copolymer Resins of Vinyl Chloride,Determination of Ph of Aqu
- EN-ISO-1265 - Plastics - Poly(Vinyl Chloride) Resins - Determination of Number of Impurities & Forei
- EN-ISO-1269 - Plastics, Homopolymer & Copolymer Resins of Vinyl Chloride, Determination of Volatile
- EN-ISO-14663-1 - Part 1: Designation System & Basis for Specifications, Plastics - Ethylene/Vinyl Alcoh
- EN-ISO-14663-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Ethyle
- EN-ISO-14910-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification (ISO 14910-1:2013)
- EN-ISO-14910-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013)
- EN-ISO-15023-1 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 1: Designation system and basis for specifications
- EN-ISO-15023-2 - Part 2: Determination of Properties, Plastics - Poly(Vinyl Alcohol) (Pval) Materials
- EN-ISO-15103-1 - Part 1: Designation System & Basis for Specifications, Poly(Phenylene Ether) (Ppe) Mou
- EN-ISO-15103-2 - Plastics, Poly(Phenylene Ether) (Ppe) Moulding & Extrusion Materials, Preparation of T
- EN-ISO-15526-1 - Part 1: Designation System & Basis for Specifications, Plastics, Polyketone (Pk) Mould
- EN-ISO-15526-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Polyket
- EN-ISO-1622-1 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1622-1:2012)
- EN-ISO-1622-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Polystyrene (Ps)
- EN-ISO-1628-3 - Part 3: Polyethylenes & Polypropylenes, Plastics - Determination of the Viscosity of P
- EN-ISO-1628-5 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 5: Thermoplastic polyester (TP) homopolymers and copolymers
- EN-ISO-16396-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications
- EN-ISO-16396-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-17855-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-17855-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms
- EN-ISO-1872-1 - Part 1: Designation System & Basis for Specifications, Polyethylene (Pe) Moulding & Ex
- EN-ISO-1872-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Polyet
- EN-ISO-1873-2 - Plastics, Polypropylene (Pp) Moulding & Extrusion Materials, Preparation of Test Speci
- EN-ISO-1874-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
- EN-ISO-19062-1 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19062-2 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)
- EN-ISO-19063-1 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19064-1 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19065-1 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19065-2 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19065-2:2019)
- EN-ISO-19066-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19069-1 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-19069-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-19892 - Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling
- EN-ISO-20028-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-20028-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-20029-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties
- EN-ISO-20557-1 - Plastics - Poly (phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-20557-2 - Plastics - Poly (phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties
- EN-ISO-20558-1 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20558-1:2018)
- EN-ISO-20558-2 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties (ISO 20558-2:2018)
- EN-ISO-20568-1 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-20568-2 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-21301-1 - Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21301-1:2019)
- EN-ISO-21301-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21301-2:2019)
- EN-ISO-21302-1 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21302-1:2019)
- EN-ISO-21302-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21302-2:2019)
- EN-ISO-21304-1 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21304-1:2019)
- EN-ISO-21305-1 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21305-1:2019)
- EN-ISO-21305-2 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21305-2:2019)
- EN-ISO-21306-1 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21306-1:2019)
- EN-ISO-21306-2 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21306-2:2019)
- EN-ISO-21309-1 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21309-1:2019)
- EN-ISO-21309-2 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21309-2:2019)
- EN-ISO-21970-1 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-21970-2 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-25137-1 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-25137-2 - Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-28941-1 - Part 1: Designation System & Basis for Specifications, Plastics - Poly(Phenylene Ether
- EN-ISO-2897-1 - Part 1: Designation System & Basis for Specifications, Impact-Resistant Polystyrene (P
- EN-ISO-293 - Plastics, Compression Moulding of Test Specimens of Thermoplastic Materials
- EN-ISO-294-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
- EN-ISO-294-5 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2011)
- EN-ISO-29988-1 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- EN-ISO-29988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- EN-ISO-305 - Determination of Thermal Stability of Poly(Vinyl Chloride),Related Chlorine-Containin
- EN-ISO-306 - Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013)
- EN-ISO-307 - Plastics - Polyamides - Determination of viscosity number - Amendment 1: Corrections, and update to reference to JIS K 6920-2 (ISO 307:2007/Amd 1:2013)
- EN-ISO-3451-5 - Plastics, Determination of Ash, Poly(Vinyl Chloride)
- EN-ISO-4613-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics, Ethylen
- EN-ISO-4894-1 - Part 1: Designation System & Basis for Specifications, Styrene/Acrylonitrile (San) Mou
- EN-ISO-4894-2 - Plastics: Styrene/Acrylonitrile (San) Moulding & Extrusion Materials Part 2: Preparati
- EN-ISO-6401 - Plastics - Poly(Vinyl Chloride) - Determination of Residual Vinyl Chloride Monomer -
- EN-ISO-7391-1 - Plastics, Polycarbonate (Pc) Moulding & Extrusion Materials, Designation System & Basi
- EN-ISO-7391-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Polyca
- EN-ISO-7792-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7792-1:2012)
- EN-ISO-7792-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012)
- EN-ISO-8257-1 - Part 1: Designation System & Basis for Specifications, Plastics - Poly(Methyl Methacry
- EN-ISO-8257-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Poly(m
- EN-ISO-8986-1 - Part 1: Designation System & Basis for Specifications, Plastics - POLYBUTENE-1 (PB-1)
- EN-ISO-8986-2 - Part 2: Preparation of Test Specimens & Determination of Properties, Plastics - Polybu
- EN-ISO-9988-1 - Plastics, Polyoxymethylene (Pom) Moulding & Extrusion Materials, Designation System &
- EN-ISO-9988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- JIS-K-7390 - Testing methods for reclaimed poly (ethylene terephthalate) (PET) moulding materials from PET bottle
- SIS-161415 - Bank document - Bill of exchange form
- SIS-161431 - Plastics - Determination of behaviour in a ventilated tubular oven
- SIS-ISO/TR-23891 - Plastics - Recycling Necessity of standards (ISO/TR 23891:2020)
- SMS-2526 - Plaströr - Avloppsrördelar av styv PVC - Förminskningsrör
- SMS-2527 - Plaströr - Avloppsrör och rördelar av styv PVC - Tätningsringar av gummi
- SS-161147 - Plastics - Determination of the melt flow rate ofthermoplastics
- SS-161154 - Plastics - Injection moulding test specimens of thermoplastic materials
- SS-166301 - Permanently installed outdoor fitness equipment - Safety requirements and test methods
- SS-166311 - Plastics - Determination of viscosity number of PVC resins in dilute solution
- SS-EN-12118 - Plastics piping systems - Determination of moisture content in thermoplastics by coulometry
- SS-EN-12200-1 - Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
- SS-EN-12733 - Agricultural and forestry machinery - Pedestrian controlled motor mowers - Safety
- SS-EN-13067 - Plastics welding personnel - Qualification of welders - Thermoplastics welded assemblies
- SS-EN-13100-4 - Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing
- SS-EN-1436 - Road marking materials - Road marking performance for road users and test methods
- SS-EN-15342 - Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates
- SS-EN-15343 - Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content
- SS-EN-15344 - Plastics - Recycled plastics - Characterization of Polyethylene (PE) recyclates
- SS-EN-15345 - Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates
- SS-EN-15346 - Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
- SS-EN-15347 - Plastics - Recycled Plastics - Characterisation of plastics wastes
- SS-EN-15348 - Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates
- SS-EN-15860 - Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods
- SS-EN-16296 - Imperfections in thermoplastics welded joints - Quality levels
- SS-EN-17271 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the peel strength of profiles laminated with foils
- SS-EN-17398 - Patient involvement in health care - Minimum requirements for person-centred care
- SS-EN-17533 - Gaseous hydrogen - Cylinders and tubes for stationary storage
- SS-EN-1778 - Characteristic values for welded thermoplastic constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment
- SS-EN-477 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling mass
- SS-EN-478 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the appearance after exposure at 150 °C
- SS-EN-479 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion
- SS-EN-513 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to artificial weathering
- SS-EN-514 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the strength of welded corners and T-joints
- SS-EN-ISO-10350-1 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
- SS-EN-ISO-10350-1-AM1 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2008/Amd 1:2014)
- SS-EN-ISO-10366-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002)
- SS-EN-ISO-10366-2 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 10366-2:2003)
- SS-EN-ISO-1043-1 - Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2011)
- SS-EN-ISO-1043-3 - Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:2016)
- SS-EN-ISO-1043-4 - Plastics - Symbols and abbreviated terms - Part 4: Flame retardants (ISO 1043-4:2021)
- SS-EN-ISO-1043-4-AM1 - Plastics - Symbols and abbreviated terms - Part 4: Flame retardants (ISO 1043-4:1998/Amd 1:2016)
- SS-EN-ISO-1060-1 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998)
- SS-EN-ISO-1060-2 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 1060-2:1998)
- SS-EN-ISO-10893-12-AM1 - Non-destructive testing of steel tubes - Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except submerged arc-welded) steel tubes - Amendment 1: Change of acceptance criteria (ISO 10893-12:2011/Amd 1:2020)
- SS-EN-ISO-10893-1-AM1 - Non-destructive testing of steel tubes - Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness - Amendment 1: Change of dimensions of the reference notch; change acceptance criteria (ISO 10893-1:2011/Amd 1:2020)
- SS-EN-ISO-1110 - Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:2019)
- SS-EN-ISO-1133 - Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005)
- SS-EN-ISO-1133-1 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2022)
- SS-EN-ISO-1133-2 - Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
- SS-EN-ISO-11337 - Plastics - Polyamides - Determination of e-caprolactam and w-laurolactam by gas chromatography (ISO 11337:2010)
- SS-EN-ISO-11468 - Plastics - Preparation of PVC pastes for test purposes - Dissolver method (ISO 11468:1997)
- SS-EN-ISO-11542-1 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 11542-1:2001)
- SS-EN-ISO-11542-2 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998)
- SS-EN-ISO-1163-1 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995)
- SS-EN-ISO-12086-1 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 12086-1:2006)
- SS-EN-ISO-12086-2 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 12086:2006/Cor 1:2006)
- SS-EN-ISO-12162 - Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
- SS-EN-ISO-1264 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH aqueous extract(ISO 1264:1980)
- SS-EN-ISO-1265 - Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles (ISO 1265:2007)
- SS-EN-ISO-1269 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water) (ISO 1269:2006)
- SS-EN-ISO-14446 - Binders for paints and varnishes - Determination of the viscosity of industrial cellulose nitrate solutions and classification of such solutions (ISO 14446:1999)
- SS-EN-ISO-14663-1 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 14663-1:1999)
- SS-EN-ISO-14663-2 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 14663-2:1999)
- SS-EN-ISO-14910-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification (ISO 14910-1:2013)
- SS-EN-ISO-14910-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013)
- SS-EN-ISO-15013 - Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)
- SS-EN-ISO-15023-1 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 1: Designation system and basis for specifications (ISO 15023-1:2017)
- SS-EN-ISO-15023-2 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 2: Determination of properties (ISO 15023-2:2019)
- SS-EN-ISO-15103-1 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 15103-1:2000)
- SS-EN-ISO-15103-2 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007)
- SS-EN-ISO-15526-1 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 15526-1:2000)
- SS-EN-ISO-15526-2 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000)
- SS-EN-ISO-1597 - Plastics - Unplasticized cellulose acetate - Determination of acetic acid yield (ISO 1597:1994)
- SS-EN-ISO-1622-1 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1622-1:2012)
- SS-EN-ISO-1622-2 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1622-2:1995)
- SS-EN-ISO-1624 - Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water (ISO 1624:2001)
- SS-EN-ISO-1628-2 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride) resins (ISO 1628-2:2020)
- SS-EN-ISO-1628-3 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes (ISO 1628-3:2010)
- SS-EN-ISO-1628-5 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 5: Thermoplastic polyester (TP) homopolymers and copolymers (ISO 1628-5:1998)
- SS-EN-ISO-16396-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 16396-1:2022)
- SS-EN-ISO-16396-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2022)
- SS-EN-ISO-17855-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 17855-1:2014)
- SS-EN-ISO-17855-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016)
- SS-EN-ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms (ISO 18064:2022)
- SS-EN-ISO-182-2 - Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 2: ph method (ISO 182-2:1990)
- SS-EN-ISO-1872-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1872-1:1993)
- SS-EN-ISO-1872-2 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007)
- SS-EN-ISO-1872-2-AM1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 1872-2:1997/Amd 1:2000)
- SS-EN-ISO-1873-1 - Plastics - Polypropene (PP) moulding and extrusion materials - Part 1: Designation system and basisfor specifications (ISO 1873-1:1995)
- SS-EN-ISO-1873-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007)
- SS-EN-ISO-1873-2-AM1 - Plastics - Polypropylen (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 1873-2:1997/Amd 1:2000)
- SS-EN-ISO-1874-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 1874-1:2010)
- SS-EN-ISO-1874-2 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
- SS-EN-ISO-1874-2-AM1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1: Laser sintering of specimens (ISO 1874-2:2006/Amd 1:2010)
- SS-EN-ISO-19062-1 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015)
- SS-EN-ISO-19062-2 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19062-2:2019)
- SS-EN-ISO-19063-1 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19063-1:2015)
- SS-EN-ISO-19063-2 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19063-2:2020)
- SS-EN-ISO-19064-1 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19064-1:2015)
- SS-EN-ISO-19065-1 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19065-1:2014)
- SS-EN-ISO-19065-2 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19065-2:2019)
- SS-EN-ISO-19066-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19066-1:2014)
- SS-EN-ISO-19069-1 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19069-1:2015)
- SS-EN-ISO-19069-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016)
- SS-EN-ISO-19892 - Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling (ISO 19892:2011)
- SS-EN-ISO-20028-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 20028-1:2019)
- SS-EN-ISO-20028-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017)
- SS-EN-ISO-20029-1 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1: Designation system and basis for specification (ISO 20029-1:2017)
- SS-EN-ISO-20029-2 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017)
- SS-EN-ISO-20557-1 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20557-1:2018)
- SS-EN-ISO-20557-2 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties (ISO 20557-2:2018)
- SS-EN-ISO-20558-1 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20558-1:2018)
- SS-EN-ISO-20558-2 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties (ISO 20558-2:2018)
- SS-EN-ISO-20568-1 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20568-1:2017)
- SS-EN-ISO-20568-2 - Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20568-2:2017)
- SS-EN-ISO-21301-1 - Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21301-1:2019)
- SS-EN-ISO-21301-2 - Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21301-2:2019).
- SS-EN-ISO-21302-1 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21302-1:2019)
- SS-EN-ISO-21302-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21302-2:2019)
- SS-EN-ISO-21304-1 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21304-1:2019)
- SS-EN-ISO-21304-2 - Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21304-2:2021)
- SS-EN-ISO-21305-1 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21305-1:2019)
- SS-EN-ISO-21305-2 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21305-2:2019)
- SS-EN-ISO-21306-1 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21306-1:2019)
- SS-EN-ISO-21306-2 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21306-2:2019)
- SS-EN-ISO-21309-1 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21309-1:2019)
- SS-EN-ISO-21309-2 - Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21309-2:2019)
- SS-EN-ISO-21970-1 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21970-1:2019)
- SS-EN-ISO-21970-2 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 21970-2:2019)
- SS-EN-ISO-22476-14 - Geotechnical investigation and testing - Field testing - Part 14: Borehole dynamic probing (ISO 22476-14:2020)
- SS-EN-ISO-23153-1 - Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 23153-1:2020)
- SS-EN-ISO-23153-2 - Plastics - Polyetheretherketone (PEEK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 23153-2:2020)
- SS-EN-ISO-24022-1 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24022-1:2020)
- SS-EN-ISO-24022-2 - Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24022-2:2020)
- SS-EN-ISO-24023-1 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24023-1:2020)
- SS-EN-ISO-24023-2 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24023-2:2020)
- SS-EN-ISO-24024-1 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 24024-1:2021)
- SS-EN-ISO-24024-2 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 24024-2:2021)
- SS-EN-ISO-24025-1 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24025-1:2020)
- SS-EN-ISO-24025-2 - Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24025-2:2020)
- SS-EN-ISO-24026-1 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24026-1:2020)
- SS-EN-ISO-24026-2 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 24026-2:2020)
- SS-EN-ISO-25137-1 - Plastics - Sulfone polymer moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 25137-1:2009)
- SS-EN-ISO-25137-2 - Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009)
- SS-EN-ISO-2580-1 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)
- SS-EN-ISO-2580-2 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003)
- SS-EN-ISO-28941-1 - Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 28941-1:2008)
- SS-EN-ISO-2897-1 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997)
- SS-EN-ISO-2897-2 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:2003)
- SS-EN-ISO-2898-1 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996)
- SS-EN-ISO-2898-2 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:2008:2008)
- SS-EN-ISO-293 - Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2023)
- SS-EN-ISO-294-1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)
- SS-EN-ISO-294-1-AM1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996/Amd 1:2001)
- SS-EN-ISO-294-2 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:2018)
- SS-EN-ISO-294-2-AM1 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996/Amd 1:2004)
- SS-EN-ISO-294-3 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2020)
- SS-EN-ISO-294-4 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage (ISO 294-4:2018)
- SS-EN-ISO-294-5 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2017)
- SS-EN-ISO-29664 - Plastics - Artificial weathering including acidic deposition (ISO 29664:2010)
- SS-EN-ISO-29988-1 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 29988-1:2019)
- SS-EN-ISO-29988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 29988-2:2018)
- SS-EN-ISO-305 - Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds - Discoloration method (ISO 305:2019)
- SS-EN-ISO-306 - Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2022)
- SS-EN-ISO-307 - Plastics - Polyamides - Determination of viscosity number (ISO 307:2019)
- SS-EN-ISO-307-AM1 - Plastics - Polyamides - Determination of viscosity number - Amendment 1: Corrections, and update to reference to JIS K 6920-2 (ISO 307:2007/Amd 1:2013)
- SS-EN-ISO-3451-4 - Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:1998)
- SS-EN-ISO-3451-5 - Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002)
- SS-EN-ISO-4577 - Plastics - Polypropylene and propylene-copolymers - Determination of thermal oxidative stability in air - Oven method (ISO 4577:2019)
- SS-EN-ISO-4608 - Plastics - Homopolymer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature (ISO 4608:1998)
- SS-EN-ISO-4610 - Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus (ISO 4610:2001)
- SS-EN-ISO-4612 - Plastics - Preparation of PVC pastes for test purposes - Planetary-mixer method (ISO 4612:2018)
- SS-EN-ISO-4613-1 - Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 1: Designation and specification (ISO 4613-1:1993)
- SS-EN-ISO-4613-2 - Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation oftest specimens and determination of properties (ISO 4613-2:1995)
- SS-EN-ISO-4613-2-AM1 - Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 4613-2:1995/Amd 1:2004)
- SS-EN-ISO-4894-1 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 4894-1:1997)
- SS-EN-ISO-4894-2 - Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995)
- SS-EN-ISO-6401 - Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer using gas-chromatographic method (ISO 6401:2022)
- SS-EN-ISO-6402-1 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 6402-1:2002)
- SS-EN-ISO-6402-2 - Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile (ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003)
- SS-EN-ISO-7391-1 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7391-1:2006)
- SS-EN-ISO-7391-2 - Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7391-2:2006)
- SS-EN-ISO-7792-1 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7792-1:2012)
- SS-EN-ISO-7792-2 - Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012)
- SS-EN-ISO-8257-1 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8257-1:1998)
- SS-EN-ISO-8257-2 - Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001)
- SS-EN-ISO-8974 - Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography (ISO 8974:2002)
- SS-EN-ISO-8985 - Plastics - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content (ISO 8985:2022)
- SS-EN-ISO-8986-1 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8986-1:2009)
- SS-EN-ISO-8986-2 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:2009)
- SS-EN-ISO-8986-2-AM1 - Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 8986-2:1995/Amd 1:2000)
- SS-EN-ISO-960 - Plastics - Polyamides (PA) - Determination of water content (ISO 960:1988)
- SS-EN-ISO-9988-1 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 9988-1:2004)
- SS-EN-ISO-9988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006)
- SS-EN-ISO/IEC-27018 - Information technology - Security techniques - Code of practice for protection of personally identifiable information (PII) in public clouds acting as PII processors (ISO/IEC 27018:2019)
- SS-ISO-10021-5 - Information technology - Text communication - Messageoriented text interchange systems (MOTIS) - Part 5: Message store: Abstract service definition. Technical corrigendum 7
- SS-ISO-10640 - Plastics - Methodology for assessing polymer photoageing by FTIR and UV/visible spectroscopy (ISO 10640:2011, IDT)
- SS-ISO-1158 - Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine
- SS-ISO-1159 - Plastics - Vinyl chloride-vinyl acetate copolymers - Determination of vinyl acetate
- SS-ISO-1265 - Plastics - Polyvinyl chloride resins - Determination of number of impurities and foreign particles
- SS-ISO-1270 - Plastics - PVC resins - Determination of ash and sulphated ash
- SS-ISO-15023-2 - Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 2: Determination of properties
- SS-ISO-15853 - Thermoplastics materials - Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for moulding
- SS-ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms
- SS-ISO-18263-1 - Plastics - Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging - Part 1: Designation system and basis for specification (ISO 18263-1:2015, IDT)
- SS-ISO-18263-2 - Plastics - Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging - Part 2: Preparation of test specimens and determination of properties (ISO 18263-2:2015, IDT)
- SS-ISO-24538 - Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of residual vinyl chloride monomer by gas-chromatographic analysis of dry powder (ISO 24538:2008, IDT)
- SS-ISO-2557-1 - Plastics - Amorphous thermoplastics - Preparationof test specimens with a specified maximum reversion - Part 1: Bars
- SS-ISO-2557-2 - Plastics - Amorphous thermoplastics - Preparationof test specimens with a specified reversion - Part 2: Plates
- SS-ISO-2561 - Plastics - Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography (ISO 2561:2012, IDT)
- SS-ISO-28078-1 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 28078-1:2009, IDT)
- SS-ISO-28078-2 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 28078-2:2009, IDT)
- SS-ISO-2898-1 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- SS-ISO-293 - Plastics - Compression moulding test specimens ofthermoplastic materials
- SS-ISO-294-5 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2011, IDT)
- SS-ISO-29664 - Plastics - Artificial weathering including acidic deposition (ISO 29664:2010, IDT)
- SS-ISO-3451-2 - Plastics - Determination of ash - Part 2: Poly(alkylene terephthalate) materials (ISO 3451-2:1998, IDT)
- SS-ISO-4575 - Plastics - Poly(vinyl chloride) pastes - Determination of apparent viscosity using the Severs rheometer (ISO 4575:2007, IDT)
- SS-ISO-4608 - Plastics - Homopolymerer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature
- SS-ISO-4612 - Plastics - PVC paste resins - Preparation of a paste
- SS-ISO-6469-3-AM1 - Withstand voltage test for electric power sources (ISO 6469-3:2018/Amd 1:2020, IDT)
- SS-ISO-6691 - Thermoplastic polymers for plain bearings - Classification and designation (ISO 6691:2000, IDT)
- SS-ISO-9988-2 - Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006, IDT)
- UNE-EN-ISO-1628-5 - Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 5: Thermoplastic polyester (TP) homopolymers and copolymers
- UNE-EN-ISO-16396-1 - Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications
- UNE-EN-ISO-17855-1 - Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- UNE-EN-ISO-18064 - Thermoplastic elastomers - Nomenclature and abbreviated terms
- UNE-EN-ISO-19066-1 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- UNE-EN-ISO-19069-1 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- UNE-EN-ISO-19069-2 - Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties