ASTM-D5204 Standard Classification System and Basis for Specification for Polyamide-Imide (PAI) Molding and Extrusion Materials

ASTM-D5204 - 2022 EDITION - CURRENT -- See the following: MIL-P-46179
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This classification system covers polyamide-imide materials suitable for injection molding and extrusion. Polyamide-imide materials are classified into groups that are subdivided into classes and grades. These groups are: Group 01 which is suitable for injection molding, Group 02 which is suitable for extrusion, and Group 03 which is for other purposes. Each group is then subdivided into classes such as Class 1 used for general purpose, Class 2 used for wear resistance, Class 3 used for high strength conditions, and Class 0 for other conditions. Different tests shall be conducted in order to determine the following properties of polyamide-imide materials: tensile strength, elongation, flexural strength, flexural modulus, and Izod impact strength.

ORDER

Price:

$69.00        


Want this as a site license?

Scope

1.1 This classification system covers polyamide-imide materials suitable for injection molding and extrusion.

1.2 The properties included in this classification system are those required to identify the compositions covered. It is possible that other requirements are necessary to identify particular characteristics important to specialized applications. The use of suffixes as shown in Section 5 is one way of specifying these requirements.

1.3 This standard allows for the use of recycled materials provided that specification requirements based upon this classification system are met.

1.4 This classification system and subsequent line call-out (specification) is intended to be a means of calling out plastics materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection needs to be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification, and the economics.

1.5 The values stated in SI units are to be regarded as the standard. (Reporting in inch-pound units is acceptable.)

1.6 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: There is no known ISO equivalent to this standard.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

extrusion material; line call-out; molding material; polyamide-imide;

To find similar documents by ASTM Volume:

08.03 (Plastics (III): D5117 - latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products)

To find similar documents by classification:

83.080.20 (Thermoplastic materials)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-A240
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM-A370
Standard Test Methods and Definitions for Mechanical Testing of Steel Products

ASTM-E8
Standard Test Methods for Tension Testing of Metallic Materials

Document Number

ASTM-D5204-22

Revision Level

2022 EDITION

Status

Current

Modification Type

Revision

Publication Date

Nov. 16, 2022

Document Type

Specification

Page Count

8 pages

Committee Number

D20.15