03.02: Corrosion of Metals; Wear and Erosion
ASTM International (formerly the American Society for Testing and Materials) has published a complete collection of their standards for some time. This collection is divided into Sections and Volumes by subject classification for increased useability.
Return to Section Index
The following documents are a part of this series:
- ASTM-B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus
- ASTM-B287 - Method of Acetic Acid-Salt Spray (Fog) Testing (Withdrawn 1987)
- ASTM-B611 - Standard Test Method for Determining the High Stress Abrasion Resistance of Hard Materials
- ASTM-C876 - Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete
- ASTM-D2776 - Standard Test Methods for Corrosivity of Water in the Absence of Heat Transfer (Electrical Methods)
- ASTM-G1 - Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
- ASTM-G100 - Standard Test Method for Conducting Cyclic Galvanostaircase Polarization
- ASTM-G101 - Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
- ASTM-G102 - Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements
- ASTM-G103 - Standard Practice for Evaluating Stress-Corrosion Cracking Resistance of Low Copper 7XXX Series Al-Zn-Mg-Cu Alloys in Boiling 6 % Sodium Chloride Solution
- ASTM-G105 - Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
- ASTM-G106 - Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements
- ASTM-G107 - Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input
- ASTM-G108 - Standard Test Method for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels
- ASTM-G109 - Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments
- ASTM-G110 - Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
- ASTM-G111 - Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both
- ASTM-G112 - Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys
- ASTM-G115 - Standard Guide for Measuring and Reporting Friction Coefficients
- ASTM-G116 - Standard Practice for Conducting Wire-on-Bolt Test for Atmospheric Galvanic Corrosion
- ASTM-G117 - Standard Guide for Calculating and Reporting Measures of Precision Using Data from Interlaboratory Wear or Erosion Tests (Withdrawn 2016)
- ASTM-G118 - Standard Guide for Recommended Format of Wear Test Data Suitable for Databases (Withdrawn 2016)
- ASTM-G119 - Standard Guide for Determining Synergism Between Wear and Corrosion
- ASTM-G123 - Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution
- ASTM-G129 - Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking
- ASTM-G132 - Standard Test Method for Pin Abrasion Testing
- ASTM-G133 - Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
- ASTM-G134 - Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet
- ASTM-G135 - Standard Guide for Computerized Exchange of Corrosion Data for Metals (Withdrawn 2023)
- ASTM-G137 - Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
- ASTM-G139 - Standard Test Method for Determining Stress-Corrosion Cracking Resistance of Heat-Treatable Aluminum Alloy Products Using Breaking Load Method
- ASTM-G140 - Standard Test Method for Determining Atmospheric Chloride Deposition Rate by Wet Candle Method
- ASTM-G142 - Standard Test Method for Determination of Susceptibility of Metals to Embrittlement in Hydrogen Containing Environments at High Pressure, High Temperature, or Both
- ASTM-G143 - Standard Test Method for Measurement of Web/Roller Friction Characteristics
- ASTM-G146 - Standard Practice for Evaluation of Disbonding of Bimetallic Stainless Alloy/Steel Plate for Use in High-Pressure, High-Temperature Refinery Hydrogen Service
- ASTM-G148 - Standard Practice for Evaluation of Hydrogen Uptake, Permeation, and Transport in Metals by an Electrochemical Technique
- ASTM-G149 - Standard Practice for Conducting the Washer Test for Atmospheric Galvanic Corrosion (Withdrawn 2004)
- ASTM-G15 - Standard Terminology Relating to Corrosion and Corrosion Testing (Withdrawn 2010)
- ASTM-G150 - Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels and Related Alloys
- ASTM-G157 - Standard Guide for Evaluating Corrosion Properties of Wrought Iron- and Nickel-Based Corrosion Resistant Alloys for Chemical Process Industries
- ASTM-G158 - Standard Guide for Three Methods of Assessing Buried Steel Tanks
- ASTM-G16 - Standard Guide for Applying Statistics to Analysis of Corrosion Data
- ASTM-G161 - Standard Guide for Corrosion-Related Failure Analysis
- ASTM-G162 - Standard Practice for Conducting and Evaluating Laboratory Corrosion Tests in Soils
- ASTM-G163 - Standard Guide for Digital Data Acquisition in Wear and Friction Measurements (Withdrawn 2016)
- ASTM-G164 - Standard Test Method for Determination of Surface Lubrication on Flexible Webs
- ASTM-G165 - Standard Practice for Determining Rail-to-Earth Resistance
- ASTM-G168 - Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens
- ASTM-G170 - Standard Guide for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors in the Laboratory
- ASTM-G171 - Standard Test Method for Scratch Hardness of Materials Using a Diamond Stylus
- ASTM-G174 - Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact
- ASTM-G176 - Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method
- ASTM-G180 - Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries
- ASTM-G181 - Standard Test Method for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions
- ASTM-G182 - Standard Test Method for Determination of the Breakaway Friction Characteristics of Rolling Element Bearings
- ASTM-G184 - Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using Rotating Cage
- ASTM-G185 - Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode
- ASTM-G186 - Standard Test Method for Determining Whether Gas-Leak-Detector Fluid Solutions Can Cause Stress Corrosion Cracking of Brass Alloys
- ASTM-G187 - Standard Test Method for Measurement of Soil Resistivity Using the Two-Electrode Soil Box Method
- ASTM-G188 - Standard Specification for Leak Detector Solutions Intended for Use on Brasses and Other Copper Alloys
- ASTM-G189 - Standard Guide for Laboratory Simulation of Corrosion Under Insulation
- ASTM-G190 - Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)
- ASTM-G192 - Standard Test Method for Determining the Crevice Repassivation Potential of Corrosion-Resistant Alloys Using a Potentiodynamic-Galvanostatic-Potentiostatic Technique
- ASTM-G193 - Standard Terminology and Acronyms Relating to Corrosion
- ASTM-G194 - Standard Test Method for Measuring Rolling Friction Characteristics of a Spherical Shape on a Flat Horizontal Plane
- ASTM-G195 - Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser
- ASTM-G196 - Standard Test Method for Galling Resistance of Material Couples
- ASTM-G198 - Standard Test Method for Determining the Relative Corrosion Performance of Driven Fasteners in Contact with Treated Wood
- ASTM-G199 - Standard Guide for Electrochemical Noise Measurement
- ASTM-G200 - Standard Test Method for Measurement of Oxidation-Reduction Potential (ORP) of Soil
- ASTM-G202 - Standard Test Method for Using Atmospheric Pressure Rotating Cage
- ASTM-G203 - Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems
- ASTM-G204 - Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions
- ASTM-G205 - Standard Guide for Determining Emulsion Properties, Wetting Behavior, and Corrosion-Inhibitory Properties of Crude Oils
- ASTM-G206 - Standard Guide for Measuring the Wear Volumes of Piston Ring Segments Run against Flat Coupons in Reciprocating Wear Tests
- ASTM-G208 - Standard Practice for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors Using Jet Impingement Apparatus
- ASTM-G209 - Standard Practice for Detecting mu-phase in Wrought Nickel-Rich, Chromium, Molybdenum-Bearing Alloys
- ASTM-G210 - Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
- ASTM-G211 - Standard Test Method for Conducting Elevated Temperature Erosion Tests by Solid Particle Impingement Using Gas Jets
- ASTM-G215 - Standard Guide for Electrode Potential Measurement
- ASTM-G217 - Standard Guide for Corrosion Monitoring in Laboratories and Plants with Coupled Multielectrode Array Sensor Method
- ASTM-G219 - Standard Guide for Determination of Static Coefficient of Friction of Test Couples Using an Inclined Plane Testing Device
- ASTM-G28 - Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys
- ASTM-G2M - Standard Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 633°K or in Steam at 673°K [Metric] (Withdrawn 2005)
- ASTM-G3 - Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing
- ASTM-G30 - Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens
- ASTM-G31 - Standard Guide for Laboratory Immersion Corrosion Testing of Metals
- ASTM-G32 - Standard Test Method for Cavitation Erosion Using Vibratory Apparatus
- ASTM-G33 - Standard Practice for Recording Data from Atmospheric Corrosion Tests of Metallic-Coated Steel Specimens
- ASTM-G34 - Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test)
- ASTM-G35 - Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Acids
- ASTM-G36 - Standard Practice for Evaluating Stress-Corrosion-Cracking Resistance of Metals and Alloys in a Boiling Magnesium Chloride Solution
- ASTM-G37 - Standard Practice for Use of Mattsson's Solution of pH 7.2 to Evaluate the Stress-Corrosion Cracking Susceptibility of Copper-Zinc Alloys
- ASTM-G38 - Standard Practice for Making and Using C-Ring Stress-Corrosion Test Specimens
- ASTM-G39 - Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens
- ASTM-G4 - Standard Guide for Conducting Corrosion Tests in Field Applications (Withdrawn 2023)
- ASTM-G40 - Standard Terminology Relating to Wear and Erosion
- ASTM-G41 - Standard Practice for Determining Cracking Susceptibility of Metals Exposed Under Stress to a Hot Salt Environment
- ASTM-G43 - Method of Acidified Synthetic Sea Water (Fog) Testing (Withdrawn 1987)
- ASTM-G44 - Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5 % Sodium Chloride Solution
- ASTM-G46 - Standard Guide for Examination and Evaluation of Pitting Corrosion
- ASTM-G47 - Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products
- ASTM-G48 - Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution
- ASTM-G49 - Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens
- ASTM-G5 - Standard Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements
- ASTM-G50 - Standard Practice for Conducting Atmospheric Corrosion Tests on Metals
- ASTM-G51 - Standard Test Method for Measuring pH of Soil for Use in Corrosion Testing
- ASTM-G52 - Standard Practice for Exposing and Evaluating Metals and Alloys in Surface Seawater
- ASTM-G54 - Standard Practice for Simple Static Oxidation Testing (Withdrawn 2002)
- ASTM-G56 - Standard Test Method for Abrasiveness of Ink-Impregnated Fabric Printer Ribbons and Other Web Materials (Withdrawn 2022)
- ASTM-G57 - Standard Test Method for Field Measurement of Soil Resistivity Using the Wenner Four-Electrode Method
- ASTM-G58 - Standard Practice for Preparation of Stress-Corrosion Test Specimens for Weldments
- ASTM-G59 - Standard Test Method for Conducting Potentiodynamic Polarization Resistance Measurements
- ASTM-G60 - Standard Practice for Conducting Cyclic Humidity Exposures
- ASTM-G61 - Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys
- ASTM-G64 - Standard Classification of Resistance to Stress-Corrosion Cracking of Heat-Treatable Aluminum Alloys
- ASTM-G65 - Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
- ASTM-G66 - Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)
- ASTM-G67 - Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
- ASTM-G68 - Practice for Liquid Sodium Corrosion Testing of Metals and Alloys (Withdrawn 1992)
- ASTM-G69 - Standard Test Method for Measurement of Corrosion Potentials of Aluminum Alloys
- ASTM-G71 - Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes
- ASTM-G73 - Standard Test Method for Liquid Impingement Erosion Using Rotating Apparatus
- ASTM-G75 - Standard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)
- ASTM-G76 - Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets
- ASTM-G77 - Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test
- ASTM-G78 - Standard Guide for Crevice Corrosion Testing of Iron-Base and Nickel-Base Stainless Alloys in Seawater and Other Chloride-Containing Aqueous Environments
- ASTM-G79 - Standard Practice for Evaluation of Metals Exposed to Carburization Environments (Withdrawn 2005)
- ASTM-G81 - Standard Test Method for Jaw Crusher Gouging Abrasion Test
- ASTM-G82 - Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance
- ASTM-G83 - Standard Test Method for Wear Testing with a Crossed-Cylinder Apparatus (Withdrawn 2005)
- ASTM-G84 - Standard Practice for Measurement of Time-of-Wetness on Surfaces Exposed to Wetting Conditions as in Atmospheric Corrosion Testing
- ASTM-G85 - Standard Practice for Modified Salt Spray (Fog) Testing
- ASTM-G87 - Standard Practice for Conducting Moist SO
2 Tests - ASTM-G91 - Standard Practice for Monitoring Atmospheric SO
2 Deposition Rate for Atmospheric Corrosivity Evaluation - ASTM-G92 - Standard Practice for Characterization of Atmospheric Test Sites
- ASTM-G96 - Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)
- ASTM-G97 - Standard Test Method for Laboratory Evaluation of Magnesium Sacrificial Anode Test Specimens for Underground Applications
- ASTM-G98 - Standard Test Method for Galling Resistance of Materials
- ASTM-G99 - Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus
- ASTM-NACE/ASTMG193 - Standard Terminology and Acronyms Relating to Corrosion