Document Center List of Standards on Paper And Board
ICS Code 85.060
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-D1029 - Standard Test Method for Peeling Resistance of Paper and Paperboard (Withdrawn 2001)
- ASTM-D1030 - Standard Test Method for Fiber Analysis of Paper and Paperboard (Withdrawn 2011)
- ASTM-D1164 - Method of Test for Ring Crush of Paperboard (Withdrawn 1984)
- ASTM-D1223 - Standard Test Method for Specular Gloss of Paper and Paperboard at 75° (Withdrawn 2010)
- ASTM-D1224 - Standard Test Methods for Zinc and Cadmium in Paper
- ASTM-D1584 - Method of Test for Water Absorptiveness of Paper Labels (Withdrawn 1990)
- ASTM-D1749 - Standard Practice for Interlaboratory Evaluation of Test Methods Used with Paper and Paper Products (Withdrawn 2010)
- ASTM-D1834 - Standard Test Method for 20o Specular Gloss of Waxed Paper
- ASTM-D1968 - Standard Terminology Relating to Paper and Paper Products
- ASTM-D2019 - Standard Test Method for Dirt in Paper and Paperboard (Withdrawn 2010)
- ASTM-D2020 - Standard Test Methods for Mildew (Fungus) Resistance of Paper and Paperboard (Withdrawn 2009)
- ASTM-D2175 - Standard Test Method for Book Bulk and Book Bulking Number of Paper (Withdrawn 2010)
- ASTM-D2176 - Standard Test Method for Folding Endurance of Paper and Plastics Film by the M.I.T. Tester
- ASTM-D2423 - Standard Test Method for Surface Wax on Waxed Paper or Paperboard
- ASTM-D2482 - Standard Test Method for Surface Strength of Paper (Wax Pick Method) (Withdrawn 2010)
- ASTM-D3285 - Standard Test Method for Water Absorptiveness of Nonbibulous Paper and Paperboard (Cobb Test) (Withdrawn 2010)
- ASTM-D3344 - Standard Test Method for Total Wax Content of Corrugated Paperboard
- ASTM-D3521 - Standard Test Method for Surface Wax Coating On Corrugated Board
- ASTM-D3522 - Standard Test Method for Applied Coating Wax and Impregnating (Saturating) Wax in Corrugated Board Facing (Withdrawn 2012)
- ASTM-D3708 - Standard Test Method for Weight of Wax Applied During Curtain Coating Operation (Withdrawn 2015)
- ASTM-D4714 - Standard Test Method for Determination of Effect of Moist Heat (50 % Relative Humidity and 90C) on Properties of Paper and Board (Withdrawn 2010)
- ASTM-D4988 - Standard Test Method for Determination of Alkalinity of Paper as Calcium Carbonate (Alkaline Reserve of Paper)
- ASTM-D5039 - Standard Test Methods for Identification of Wire Side of Paper (Withdrawn 2009)
- ASTM-D528 - Standard Test Method for Machine Direction of Paper and Paperboard (Withdrawn 2010)
- ASTM-D5342 - Standard Test Method for Resistance to Bending of Paper and Paperboard (Taber-Type Tester in Basic Configuration) (Withdrawn 2010)
- ASTM-D548 - Standard Test Method for Water-Soluble Acidity or Alkalinity of Paper (Withdrawn 2009)
- ASTM-D549 - Test Methods for Rosin in Paper and Paperboard (Withdrawn 1993)
- ASTM-D5625 - Standard Test Method for Measuring Length, Width, and Squareness of Sheeted Paper and Paper Products (Withdrawn 2009)
- ASTM-D5650 - Standard Test Method for Resistance to Bending of Paper of Low Bending Stiffness (Taber-Type Tester in 0 to 10 Taber Stiffness Unit Configuration) (Withdrawn 2010)
- ASTM-D5663 - Standard Guide for Validating Recycled Content in Packaging Paper and Paperboard
- ASTM-D5802 - Standard Test Method for Sorption of Bibulous Paper Products (Sorptive Rate and Capacity Using Gravimetric Principles)
- ASTM-D5834 - Standard Guide for Source Reduction Reuse, Recycling, and Disposal of Solid and Corrugated Fiberboard (Cardboard) (Withdrawn 2004)
- ASTM-D585 - Standard Practice for Sampling and Accepting a Single Lot of Paper, Paperboard, Fiberboard, and Related Product
- ASTM-D586 - Standard Test Method for Ash in Pulp, Paper, and Paper Products (Withdrawn 2009)
- ASTM-D589 - Standard Test Method for Opacity of Paper (15° Diffuse Illuminant A, 89 % Reflectance Backing and Paper Backing) (Withdrawn 2010)
- ASTM-D6043 - Standard Guide for Selection of Permanent and Durable Artist's Paper
- ASTM-D6125 - Standard Test Method for Bending Resistance of Paper and Paperboard (Gurley Type Tester) (Withdrawn 2010)
- ASTM-D6136 - Standard Test Method for Kerosine Number of Unsaturated (Dry) Felt by Vacuum Method
- ASTM-D6149 - Standard Specification for Newsprint Including Newsprint Manufactured from Recycled Fiber (Withdrawn 2003)
- ASTM-D643 - Standard Test Method for Folding Endurance of Paper by the Schopper Tester (Withdrawn 2010)
- ASTM-D644 - Standard Test Method for Moisture Content of Paper and Paperboard by Oven Drying
- ASTM-D645 - Standard Test Method for Thickness of Paper and Paperboard
- ASTM-D646 - Standard Test Method for Mass Per Unit Area of Paper and Paperboard of Aramid Papers (Basis Weight) (Withdrawn 2022)
- ASTM-D6789 - Standard Test Method for Accelerated Light Aging of Printing and Writing Paper by Xenon-Arc Exposure Apparatus (Withdrawn 2011)
- ASTM-D6819 - Standard Test Method for Accelerated Temperature Aging of Printing and Writing Paper by Dry Oven Exposure Apparatus (Withdrawn 2011)
- ASTM-D685 - Standard Practice for Conditioning Paper and Paper Products for Testing
- ASTM-D686 - Standard Test Methods of Qualitative Examination of Mineral Filler and Mineral Coating of Paper (Withdrawn 2011)
- ASTM-D722 - Standard Test Method for Grease Resistance of Paper (Withdrawn 2010)
- ASTM-D774 - Standard Test Method for Bursting Strength of Paper
- ASTM-D776 - Standard Test Method for Determination of Effect of Dry Heat on Properties of Paper and Board (Withdrawn 2009)
- ASTM-D777 - Standard Test Methods for Flammability of Treated Paper and Paperboard (Withdrawn 2009)
- ASTM-D778 - Standard Test Methods for Hydrogen Ion Concentration (pH) of Paper Extracts (Hot-Extraction and Cold-Extraction Procedures) (Withdrawn 2010)
- ASTM-D779 - Standard Test Method for Determining the Water Vapor Resistance of Sheet Materials in Contact with Liquid Water by the Dry Indicator Method
- ASTM-D781 - Method of Test for Puncture and Stiffness of Paperboard, Corrugated and Solid Fiberboard (Withdrawn 1984)
- ASTM-D824 - Standard Test Method for Rate of Absorption of Water by Bibulous Papers (Withdrawn 2010)
- ASTM-D828 - Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
- ASTM-D829 - Standard Test Methods for Wet Tensile Breaking Strength of Paper and Paper Products (Withdrawn 2009)
- ASTM-D918 - Standard Test Method for Blocking Resistance of Paper and Paperboard (Withdrawn 2011)
- ASTM-D919 - Standard Test Method for Copper Number of Paper and Paperboard (Withdrawn 2009)
- ASTM-D982 - Standard Test Method for Organic Nitrogen in Paper and Paperboard
- ASTM-D984 - Standard Test Methods for Reducible Sulfur in Paper (Withdrawn 2010)
- ASTM-D985 - Standard Test Method for Brightness of Pulp, Paper, and Paperboard (Directional Reflectance at 457 nm) (Withdrawn 2010)
- ASTM-E2022 - Standard Practice for Calculation of Weighting Factors for Tristimulus Integration
- ASTM-E2325 - Standard Guide for Non-destructive Examination of Paper (Withdrawn 2014)
- ASTM-F634 - Practice for Measurement of the Coating Transfer Resistance of Mechanical Carbonless CB Paper (Withdrawn 1986)
BSI:
- BS-2782-8-820A - Methods of testing plastics. Other properties. Determination of water vapour transmission rate (dish method)
- BS-2782-8-M-820A - Methods of testing plastics. Other properties. Determination of water vapour transmission rate (dish method)
- BS-2922-1 - Strength of wet paper and board.
- BS-2922-2 - Method for Determination of the Tensile Strength of Paper and Board After Immersion In
- BS-2924 - Methods for the determination of chloride and sulphate contents of aqueous extracts of paper and board
- BS-2924-1 - Aqueous extracts of paper, board and pulp. Method for determination of pH
- BS-2987 - Notes on the application of statistics to paper testing
- BS-3137 - Methods for determining the bursting strength of paper and board
- BS-3203 - Glossary of paper, board, pulp and related terms
- BS-3432 - Method for determination of grammage of paper and board
- BS-3631 - Method for determination of ash of paper and board
- BS-3748 - Method for determination of resistance to bending of paper and board
- BS-4000-2 - Sizes of paper and board.
- BS-4415-1 - Determination of the tensile properties of paper and board. Constant rate of loading method
- BS-4415-2 - Determination of the tensile properties of paper and board
- BS-4420 - Method for determination of the Bendtsen roughness of paper and board
- BS-4816 - Method for the determination of the puncture resistance of board
- BS-4817 - Method for the Determination of the Thickness of Corrugated Fiberboard
- BS-4818 - Method for determination of the creasing quality of carton board (Pira method)
- BS-5131-4.2 - Methods of test for footwear and footwear materials. Other components
- BS-5881 - Method for determination of grammage of single layers of solid fibreboard
- BS-6036 - Method for determination of the edgewise crush resistance of corrugated fibreboard
- BS-6225-1 - Method for determining the resistance to picking of paper and board: accelerating speed method using the IGT tester. Pendulum or spring model
- BS-6225-2 - Method for determining the resistance to picking of paper and board: accelerating speed method using the IGT tester
- BS-6504 - Method for determination of water absorption of paper and board (Klemm method)
- BS-6538-2 - Air permeance of paper and board. Method for Determination of Air Permeance Using the Bendtsen Apparatus
- BS-6712-1 - Measurement of hygroexpansivity of paper and board
- BS-6712-2 - Measurement of hygroexpansivity of paper and board
- BS-6890 - Method for determination of grease resistance of paper and board
- BS-6965-1 - Creasing properties of carton board.
- BS-7406 - Methods for determination of water vapour transmission rate of sheet materials (paper and board) by dynamic sweep and static gas methods
- BS-7424 - Guide to general principles for determination of the bending stiffness of paper and board by static methods
- BS-7500 - Specification for marking of recycled paper board
- BS-EN-1104 - Paper and board intended to come into contact with foodstuffs. Determination of the transfer of antimicrobial constituents
- BS-EN-1104-TC - Tracked Changes. Paper and board intended to come into contact with foodstuffs. Determination of the transfer of antimicrobial constituents
- BS-EN-1230-1 - Paper and board intended to come into contact with foodstuffs. Sensory analysis
- BS-EN-1230-2 - Paper and board intended to come into contact with foodstuffs. Sensory analysis
- BS-EN-12497 - Paper and board. Paper and board intended to come into contact with foodstuffs. Determination of mercury in an aqueous extract
- BS-EN-12498 - Paper and board. Paper and board intended to come into contact with foodstuffs. Determination of cadmium, chromium and lead in an aqueous extract
- BS-EN-12498-TC - Tracked Changes. Paper and board. Paper and board intended to come into contact with foodstuffs. Determination of cadmium, chromium and lead in an aqueous extract
- BS-EN-14719 - Pulp, paper and board. Determination of the diisopropylnaphthalene (DIPN) content by solvent extraction
- BS-EN-15519 - Paper and board intended to come into contact with foodstuffs. Preparation of an organic solvent extract
- BS-EN-15845 - Paper and board. Determination of the cytotoxicity of aqueous extracts
- BS-EN-16418 - Paper and board. Determination of the cytotoxicity of aqueous extracts using a metabolically competent hepatoma cell line (HepG2)
- BS-EN-16453 - Pulp, paper and paperboard. Determination of phthalates in extracts from paper and paperboard
- BS-EN-17085 - Paper and board. Sampling procedures for paper and board for recycling
- BS-EN-17163 - Pulp, paper and board - Determination of primary aromatic amines (PAA) in a water extract by a LC-MS method
- BS-EN-17545 - Paper and board. Determination of composition of paper and board for recycling by gravimetric analysis
- BS-EN-17917 - Paper and board. Paper and board intended to come into contact with foodstuffs. Determination of aluminium in aqueous extracts
- BS-EN-20187 - Paper, board and pulps. Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
- BS-EN-20535 - Paper and board. Determination of water absorptiveness. Cobb method
- BS-EN-21974 - Paper. Determination of tearing resistance (Elmendorf method)
- BS-EN-23035 - Single-Faced & Single-Wall Corrugated Fibreboard, Determination of Flat Crush Resistan
- BS-EN-643 - Paper and board. European list of standard grades of paper and board for recycling
- BS-EN-644 - Paper. Untrimmed sizes. Primary range and supplementary range designation and tolerances, expression of direction of manufacture
- BS-EN-646 - Paper and board intended to come into contact with foodstuffs. Determination of colour fastness of dyed paper and board
- BS-EN-646-TC - Tracked Changes. Paper and board intended to come into contact with foodstuffs. Determination of colour fastness of dyed paper and board
- BS-EN-648 - Paper and board intended to come into contact with foodstuffs. Determination of the fastness of fluorescent whitened paper and board
- BS-EN-648-TC - Tracked Changes. Paper and board intended to come into contact with foodstuffs. Determination of the fastness of fluorescent whitened paper and board
- BS-EN-920 - Paper and board intended to come into contact with foodstuffs. Determination of dry matter content in an aqueous extract
- BS-EN-ISO-12625-10 - Part 10: Determination of Demand Water Absorption Rate & Capacity, Under Controlled Hy
- BS-EN-ISO-12625-11 - Tissue paper and tissue products
- BS-EN-ISO-12625-12-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-15 - Tissue paper and tissue products
- BS-EN-ISO-12625-16 - Tissue paper and tissue products
- BS-EN-ISO-12625-16-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-4 - Tissue paper and tissue products
- BS-EN-ISO-12625-4-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-5-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-6-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-7 - Tissue paper and tissue products
- BS-EN-ISO-12625-7-TC - Tracked Changes. Tissue paper and tissue products
- BS-EN-ISO-12625-9 - Tissue paper and tissue products
- BS-EN-ISO-15320 - Pulp, paper and board. Determination of pentachlorophenol in an aqueous extract
- BS-EN-ISO-15755 - Paper and board. Estimation of contraries
- BS-EN-ISO-186 - Paper and board. Sampling to determine average quality
- BS-EN-ISO-187 - Paper, board and pulps. Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
- BS-EN-ISO-187-TC - Tracked Changes. Paper, board and pulps. Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
- BS-EN-ISO-1924-2 - Paper and board. Determination of tensile properties
- BS-EN-ISO-1974 - Paper. Determination of tearing resistance. Elmendorf method
- BS-EN-ISO-217 - Paper. Untrimmed sizes. Designation and tolerances for primary and supplementary ranges, and indication of machine direction
- BS-EN-ISO-2758 - Paper. Determination of bursting strength
- BS-EN-ISO-2759 - Board. Determination of bursting strength
- BS-EN-ISO-287 - Paper and board. Determination of moisture content of a lot. Oven-drying method
- BS-EN-ISO-287-TC - Tracked Changes. Paper and board. Determination of moisture content of a lot. Oven-drying method
- BS-EN-ISO-3035 - Corrugated fibreboard. Determination of flat crush resistance
- BS-EN-ISO-3037 - Corrugated fibreboard. Determination of edgewise crush resistance (non-waxed edge method)
- BS-EN-ISO-534 - Paper and board. Determination of thickness, density and specific volume
- BS-EN-ISO-535 - Paper and board. Determination of water absorptiveness. Cobb method
- BS-EN-ISO-535-TC - Tracked Changes. Paper and board. Determination of water absorptiveness. Cobb method
- BS-EN-ISO-536 - Paper and board. Determination of grammage
- BS-EN-ISO-536-TC - Tracked Changes. Paper and board. Determination of grammage
- BS-EN-ISO-638 - Paper, board and pulps. Determination of dry matter content. Oven-drying method
- BS-EN-ISO-638-1-TC - Tracked Changes. Paper, board, pulps and cellulosic nanomaterials. Determination of dry matter content by oven-drying method
- BS-EN-ISO-638-2-TC - Tracked Changes. Paper, board, pulps and cellulosic nanomaterials. Determination of dry matter content by oven-drying method
- BS-EN-ISO-7263 - Corrugating medium. Determination of the flat crush resistance after laboratory fluting
- BS-EN-ISO-7263-1 - Corrugating medium. Determination of the flat crush resistance after laboratory fluting
- BS-EN-ISO-8254-1 - Paper and board. Measurement of specular gloss
- BS-EN-ISO-8254-2 - Paper and board. Measurement of specular gloss
- BS-EN-ISO-9706 - Information and documentation. Paper for documents. Requirements for permanence
- BS-ISO-10716-TC - Tracked Changes. Paper and board. Determination of alkali reserve
- BS-ISO-10775 - Paper, board and pulps. Determination of cadmium content. Atomic absorption spectrometric method
- BS-ISO-11093-4 - Paper and board. Testing of cores
- BS-ISO-11093-4-TC - Tracked Changes. Paper and board. Testing of cores
- BS-ISO-11093-5 - Paper and board. Testing of cores
- BS-ISO-11093-6 - Paper and board. Testing of cores
- BS-ISO-11093-7 - Paper and board. Testing of cores
- BS-ISO-11093-9 - Paper and board. Testing of cores
- BS-ISO-11475 - Paper and board. Determination of CIE whiteness, D65/10 (outdoor daylight)
- BS-ISO-11475-TC - Tracked Changes. Paper and board. Determination of CIE whiteness, D65/10° (outdoor daylight)
- BS-ISO-11476 - Paper and board. Determination of CIE whiteness, C/2 (indoor illumination conditions)
- BS-ISO-11480 - Pulp, paper and board. Determination of total chlorine and organically bound chlorine
- BS-ISO-11556 - Paper and board. Determination of curl using a single vertically suspended test piece
- BS-ISO-11605 - Paper and board. Calibration of variable-area flowmeters
- BS-ISO-12192 - Paper and board. Determination of compressive strength. Ring crush method
- BS-ISO-12830 - Paper, board, pulps and cellulose nanomaterials. Determination of acid-soluble magnesium, calcium, manganese, iron, copper, sodium and potassium
- BS-ISO-13542 - Paper and board. Specification for internal diameters of cores for reels
- BS-ISO-13820 - Paper, board and corrugated fibreboard. Description and calibration of fixed platen compression-testing equipment
- BS-ISO-13820-TC - Tracked Changes. Paper, board and corrugated fibreboard - Description and calibration of fixed platen compression-testing equipment
- BS-ISO-13821 - Corrugated fibreboard. Determination of edgewise crush resistance. Waxed edge method
- BS-ISO-14968-TC - Tracked Changes. Paper and board. Cut-size office paper. Measurement of curl in a pack of sheets
- BS-ISO-15359 - Paper and board. Determination of the static and kinetic coefficients of friction. Horizontal plane method
- BS-ISO-15754 - Paper and board. Determination of z-directional tensile strength
- BS-ISO-16245 - Information and documentation. Boxes, file covers and other enclosures, made from cellulosic materials, for storage of paper and parchment documents
- BS-ISO-16245-TC - Tracked Changes. Information and documentation. Boxes, file covers and other enclosures, made from cellulosic materials, for storage of paper and parchment documents
- BS-ISO-16260 - Paper and board. Determination of internal bond strength
- BS-ISO-16532-1 - Paper and board. Determination of grease resistance
- BS-ISO-16532-2 - Paper and board. Determination of grease resistance
- BS-ISO-16945 - Corrugating medium. Determination of the edge crush resistance after laboratory fluting
- BS-ISO-1762 - Paper, board, pulps and cellulose nanomaterials. Determination of residue (ash content) on ignition at 525 C
- BS-ISO-17812 - Paper, board and pulps. Determination of total magnesium, total calcium, total manganese, total iron and total copper
- BS-ISO-1830 - Paper, board and pulps. Determination of acid-soluble manganese
- BS-ISO-18522 - Paper and board. Automated off-line testing of physical properties for CD (cross direction) profiles
- BS-ISO-1924-3 - Paper and board. Determination of tensile properties
- BS-ISO-20494 - Paper. Requirements for stability for general graphic applications
- BS-ISO-2144 - Paper, board, pulps and cellulose nanomaterials. Determination of residue (ash content) on ignition at 900 C
- BS-ISO-21993 - Paper and pulp. Deinkability test for printed paper products
- BS-ISO-22754 - Pulp and paper. Determination of the effective residual ink concentration (ERIC number) by infrared reflectance measurement
- BS-ISO-22891 - Paper. Determination of transmittance by diffuse reflectance measurement
- BS-ISO-23404 - Information and documentation. Papers and boards used for conservation. Measurement of impact of volatiles on cellulose in paper
- BS-ISO-24118-1 - Paper and board. Stylus contact method
- BS-ISO-2469 - Paper, board and pulps. Measurement of diffuse radiance factor (diffuse reflectance factor)
- BS-ISO-2469-TC - Tracked Changes. Paper, board and pulps. Measurement of diffuse radiance factor (diffuse reflectance factor)
- BS-ISO-2470 - Paper, board and pulps. Measurement of diffuse blue reflectance factor (ISO brightness)
- BS-ISO-2470-1 - Paper, board and pulps. Measurement of diffuse blue reflectance factor
- BS-ISO-2470-1-TC - Tracked Changes. Paper, board and pulps. Measurement of diffuse blue reflectance factor
- BS-ISO-2470-2 - Paper, board and pulps. Measurement of diffuse blue reflectance factor
- BS-ISO-2471 - Paper and board. Determination of opacity (paper backing). Diffuse reflectance method
- BS-ISO-2493-2 - Paper and board. Determination of resistance to bending
- BS-ISO-2528 - Sheet materials. Determination of water vapour transmission rate (WVTR). Gravimetric (dish) method
- BS-ISO-2758 - Paper - Determination of Bursting Strength
- BS-ISO-2759 - Board - Determination of Bursting Strength
- BS-ISO-3034 - Corrugated fibreboard. Determination of single sheet thickness
- BS-ISO-3039 - Corrugated fibreboard. Determination of grammage of the component papers after separation
- BS-ISO-3781 - Paper and board. Determination of tensile strength after immersion in water
- BS-ISO-3783 - Paper and board. Determination of resistance to picking. Accelerated speed method using the IGT-type tester (electric model)
- BS-ISO-4046-1 - Paper, board, pulps and related terms. Vocabulary
- BS-ISO-4046-2 - Paper, board, pulps and related terms. Vocabulary
- BS-ISO-4046-4 - Paper, board, pulps and related terms. Vocabulary
- BS-ISO-4046-4-TC - Tracked Changes. Paper, board, pulps and related terms. Vocabulary
- BS-ISO-4046-5 - Paper, board, pulps and related terms. Vocabulary
- BS-ISO-4094 - Paper, board and pulps. General requirements for the competence of laboratories authorized for the issue of optical reference transfer standards of level 3
- BS-ISO-5628 - Paper and board. Determination of bending stiffness. General principles for two-point, three-point and four-point methods
- BS-ISO-5629 - Paper and board. Determination of bending stiffness. Resonance method
- BS-ISO-5630-5 - Paper and board. Accelerated ageing
- BS-ISO-5630-6 - Paper and board. Accelerated ageing
- BS-ISO-5630-7 - Paper and board. Accelerated ageing
- BS-ISO-5631 - Paper and board. Determination of colour (C/2). Diffuse reflectance method
- BS-ISO-5631-1 - Paper and board. Determination of colour by diffuse reflectance
- BS-ISO-5631-2 - Paper and board. Determination of colour by diffuse reflectance
- BS-ISO-5631-3 - Paper and board. Determination of colour by diffuse reflectance
- BS-ISO-5636-3 - Paper and board. Determination of air permeance (medium range)
- BS-ISO-5636-4 - Paper and board. Determination of air permeance (medium range)
- BS-ISO-5636-5 - Paper and board. Determination of air permeance (medium range)
- BS-ISO-5636-6 - Paper and board. Determination of air permeance (medium range)
- BS-ISO-5647 - Paper and board. Determination of titanium dioxide content
- BS-ISO-6587 - Paper, board and pulps. Determination of conductivity of aqueous extracts
- BS-ISO-6587-TC - Tracked Changes. Paper, board and pulps. Determination of conductivity of aqueous extracts
- BS-ISO-6588-1 - Paper, board and pulps. Determination of pH of aqueous extracts
- BS-ISO-6588-1-TC - Tracked Changes. Paper, board and pulps. Determination of pH of aqueous extracts
- BS-ISO-6588-2 - Paper, board and pulps. Determination of pH of aqueous extracts
- BS-ISO-7763 - Testing of paper and board. Compressive strength of a sample held in S-shape
- BS-ISO-777 - Paper, board and pulp. Determination of acid-soluble calcium
- BS-ISO-778 - Paper, board and pulp. Determination of acid-soluble copper
- BS-ISO-779 - Paper, board and pulp. Determination of acid-soluble iron
- BS-ISO-8254-3 - Paper and board. Measurement of specular gloss
- BS-ISO-8562 - Paper and board. Determination of alkali reserve
- BS-ISO-8784-1 - Pulp, paper and board. Microbiological examination
- BS-ISO-8784-2 - Pulp, paper and board. Microbiological examination
- BS-ISO-8784-3 - Pulp, paper and board. Microbiological examination
- BS-ISO-8791-2 - Paper and board. Determination of roughness/smoothness (air leak methods)
- BS-ISO-8791-3 - Paper and board. Determination of roughness/smoothness (air leak methods)
- BS-ISO-8791-4 - Paper and board. Determination of roughness/smoothness (air leak methods)
- BS-ISO-8791-4-TC - Tracked Changes. Paper and board. Determination of roughness/smoothness (air leak methods)
- BS-ISO-8791-5 - Paper and board. Determination of roughness/smoothness (air leak methods)
- BS-ISO-9184-1-TC - Tracked Changes. Paper, board and pulps. Fibre furnish analysis
- BS-ISO-9197 - Paper, board and pulps. Determination of water-soluble chlorides
- BS-ISO-9197-TC - Tracked Changes. Paper, board and pulps. Determination of water-soluble chlorides
- BS-ISO-9416 - Paper. Determination of light scattering and absorption coefficients (using Kubelka-Munk theory)
- BS-ISO-9895 - Paper and board. Compressive strength. Short-span test
- BS-ISO-9932 - Paper and board. Determination of water vapour transmission rate of sheet materials. Dynamic sweep and static gas methods
- BS-ISO-9932-TC - Tracked Changes. Paper and board. Determination of water vapour transmission rate of sheet materials. Dynamic sweep and static gas methods
- DD-ENV-12497 - Paper and board. Paper and board intended to come into contact with foodstuffs. Determination of mercury in an aqueous extract
- DD-ENV-12498 - Paper & Board Intended To Come Into Contact With COODSTUFFS-Determination of Cadmium,
- PD-CEN-15645-1 - Paper and board intended to come into contact with foodstuffs. Calibration of the off-flavour test. Odour
- PD-CEN-15645-2 - Paper and board intended to come into contact with foodstuffs. Calibration of the off flavour test. Fatty food
- PD-CEN-15645-3 - Paper and board intended to come into contact with foodstuffs. Calibration of the off-flavour test. Dry food
- PD-CEN-17497 - Pulp, paper and paperboard. Determination of bisphenol A in extracts from paper and paperboard
- PD-CEN-17630 - Pulp, paper and paperboard. Determination of anthraquinone in extracts from pulp, paper and paperboard
- PD-CEN-17830 - Paper and board. Guidance on the application of Term 2.2 'Prohibited materials' of EN 643:2014
- PD-ISO-10688 - Paper, board and pulps. Basic terms and equations for optical properties
- PD-ISO-14778 - Paper and board. Measurement of water contact angle by optical methods
- PD-ISO-17958 - Paper and board. Determination of fracture toughness. Constant rate of elongation method (1,7 mm/s)
- PD-ISO-19857 - Paper, board and printing inks. Printability. Laboratory test method for offset ink setting
- PD-ISO-20460 - Paper and board. Automated on-line testing. Metrological comparability between standardized measurements and output of on-line gauges
- PD-ISO-23885 - Paper, board and graphic technology. Determination of the coating strength in the inner fold
- PD-ISO-24498 - Paper, board and pulps. Estimation of uncertainty for test methods by interlaboratory comparisons
- PD-ISO-24498-TC - Tracked Changes. Paper, board and pulps. Estimation of uncertainty for test methods by interlaboratory comparisons
- PD-ISO-25477 - Paper, board and pulps. Basic guidelines for image analysis measurements
ISO:
- ISO-10688 - Paper, board and pulps - Basic terms and equations for optical properties
- ISO-10716 - Paper and board - Determination of alkali reserve
- ISO-10775 - Paper, board and pulps - Determination of cadmium content - Atomic absorption spectrometric method
- ISO-11093-1 - Paper and board -- Testing of cores -- Part 1: Sampling
- ISO-11093-2 - Paper and board -- Testing of cores -- Part 2: Conditioning of test samples
- ISO-11093-3 - Paper and board -- Testing of cores -- Part 3: Determination of moisture content using the oven drying method
- ISO-11093-4 - Paper and board - Testing of cores - Part 4: Measurement of dimensions
- ISO-11093-5 - Paper and board - Testing of cores - Part 5: Determination of characteristics of concentric rotation
- ISO-11093-6 - Paper and board - Testing of cores - Part 6: Determination of bending strength by the three-point method
- ISO-11093-7 - Paper and board - Testing of cores - Part 7: Determination of flexural modulus by the three-point method
- ISO-11093-8 - Paper and board - Testing of cores - Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis
- ISO-11093-9 - Paper and board - Testing of cores - Part 9: Determination of flat crush resistance
- ISO-11108 - Information and documentation -- Archival paper -- Requirements for permanence and durability
- ISO-11475 - Paper and board - Determination of CIE whiteness, D65/10 degrees (outdoor daylight)
- ISO-11476 - Paper and board - Determination of CIE whiteness, C/2° (indoor illumination conditions)
- ISO-11480 - Pulp, paper and board - Determination of total chlorine and organically bound chlorine
- ISO-11556 - Paper and board - Determination of curl using a single vertically suspended test piece
- ISO-12192 - Paper and board - Determination of compressive strength - Ring crush method
- ISO-12625-1 - Tissue paper and tissue products - Part 1: Vocabulary
- ISO-12625-11 - Tissue paper and tissue products - Part 11: Determination of wet ball burst strength
- ISO-12625-12 - Tissue paper and tissue products - Part 12: Determination of tensile strength of perforated lines and calculation of perforation efficiency
- ISO-12625-15 - Tissue paper and tissue products - Part 15: Determination of optical properties - Measurement of brightness and colour with C/2° (indoor daylight) illuminant
- ISO-12625-16 - Tissue paper and tissue products - Part 16: Determination of optical properties - Diffuse reflectance method for opacity (paper backing)
- ISO-12625-3 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density and bulk
- ISO-12625-4 - Tissue paper and tissue products - Part 4: Determination of tensile strength, stretch at maximum force and tensile energy absorption
- ISO-12625-5 - Tissue paper and tissue products - Part 5: Determination of wet tensile strength
- ISO-12625-6 - Tissue paper and tissue products - Part 6: Determination of grammage
- ISO-12625-7 - Tissue paper and tissue products - Part 7: Determination of optical properties - Measurement of brightness and colour with D65/10° (outdoor daylight)
- ISO-12625-8 - Tissue paper and tissue products - Part 8: Water-absorption time and water-absorption capacity, basket-immersion test method
- ISO-12625-9 - Tissue paper and tissue products - Part 9: Determination of ball burst strength
- ISO-12830 - Paper, board, pulps and cellulose nanomaterials - Determination of acid-soluble magnesium, calcium, manganese, iron, copper, sodium and potassium
- ISO-13542 - Paper and board - Specification for internal diameters of cores for reels
- ISO-13821 - Corrugated fibreboard - Determination of edgewise crush resistance - Waxed edge method
- ISO-14778 - Paper and board - Measurement of water contact angle by optical methods
- ISO-14968 - Paper and board - Cut-size office paper - Measurement of curl in a pack of sheets
- ISO-15318 - Pulp, paper and board -- Determination of 7 specified polychlorinated biphenyls (PCB)
- ISO-15320 - Pulp, paper and board - Determination of pentachlorophenol in an aqueous extract
- ISO-15359 - Paper and board -- Determination of the static and kinetic coefficients of friction -- Horizontal plane method
- ISO-15754 - Paper and board - Determination of z-directional tensile strength
- ISO-15755 - Paper and board -- Estimation of contraries
- ISO-16260 - Paper and board - Determination of internal bond strength
- ISO-16532-1 - Paper and board - Determination of grease resistance - Part 1: Permeability test
- ISO-16532-2 - Paper and board - Determination of grease resistance - Part 2: Surface repellency test
- ISO-16532-3 - Paper and board - Determination of grease resistance - Part 3: Turpentine test for voids in glassine and greaseproof papers
- ISO-16945 - Corrugating medium - Determination of the edge crush resistance after laboratory fluting
- ISO-17812 - Paper, board and pulps - Determination of total magnesium, total calcium, total manganese, total iron and total copper
- ISO-17958 - Paper and board - Determination of fracture toughness - Constant rate of elongation method (1,7 mm/s)
- ISO-1830 - Paper, board and pulps - Determination of acid-soluble manganese
- ISO-18522 - Paper and board - Automated off-line testing of physical properties for CD (cross direction) profiles
- ISO-186 - Paper and board - Sampling to determine average quality
- ISO-187 - Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
- ISO-1924-2 - Paper and board - Determination of tensile properties - Part 2: Constant rate of elongation method (20 mm/min)
- ISO-1924-3 - Paper and board - Determination of tensile properties - Part 3: Constant rate of elongation method (100 mm/min)
- ISO-1974 - Paper - Determination of tearing resistance - Elmendorf method
- ISO-19857 - Paper, board and printing inks . Printability . Laboratory test method for offset ink setting
- ISO-20460 - Paper and board - Automated on-line testing - Metrological comparability between standardized measurements and output of on-line gauges
- ISO-20494 - Paper - Requirements for stability for general graphic applications
- ISO-2144 - Paper, board, pulps and cellulose nanomaterials - Determination of residue (ash content) on ignition at 900 °C
- ISO-2144-RL - Paper, board and pulps - Determination of residue (ash) on ignition at 900 degrees C (includes Redline Version)
- ISO-217 - Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction
- ISO-21993 - Paper and pulp - Deinkability test for printed paper products
- ISO-22414 - Paper - Cut-size office paper - Measurement of edge quality
- ISO-22754 - Pulp and paper - Determination of the effective residual ink concentration (ERIC number) by infrared reflectance measurement
- ISO-22891 - Paper - Determination of transmittance by diffuse reflectance measurement
- ISO-23404 - Information and documentation - Papers and boards used for conservation - Measurement of impact of volatiles on cellulose in paper
- ISO-23885 - Paper, board and graphic technology - Determination of the coating strength in the inner fold
- ISO-24118-1 - Paper and board - Stylus contact method - Part 1: Determination of surface roughness
- ISO-24498 - Paper, board and pulps - Estimation of uncertainty for test methods by interlaboratory comparisons
- ISO-2469 - Paper, board and pulps - Measurement of diffuse radiance factor (diffuse reflectance factor)
- ISO-2470-1 - Paper, board and pulps - Measurement of diffuse blue reflectance factor - Part 1: Indoor daylight conditions (ISO brightness)
- ISO-2470-2 - Paper, board and pulps - Measurement of diffuse blue reflectance factor - Part 2: Outdoor daylight conditions (D65 brightness)
- ISO-2471 - Paper and board - Determination of opacity (paper backing) - Diffuse reflectance method
- ISO-2493-1 - Paper and board - Determination of bending resistance - Part 1: Constant rate of deflection
- ISO-2493-2 - Paper and board - Determination of resistance to bending - Part 2: Taber-type tester
- ISO-2528 - Sheet materials - Determination of water vapour transmission rate (WVTR) - Gravimetric (dish) method
- ISO-25477 - Paper, board and pulps - Basic guidelines for image analysis measurements
- ISO-2758 - Paper - Determination of bursting strength
- ISO-2759 - Board - Determination of bursting strength
- ISO-287 - Paper and board - Determination of moisture content of a lot - Oven-drying method
- ISO-3034 - Corrugated fibreboard - Determination of single sheet thickness
- ISO-3035 - Corrugated fibreboard - Determination of flat crush resistance
- ISO-3036 - Board -- Determination of puncture resistance
- ISO-3037 - Corrugated fibreboard - Determination of edgewise crush resistance (non-waxed edge method)
- ISO-3038 - Corrugated fibreboard -- Determination of the water resistance of the glue bond by immersion
- ISO-3039 - Corrugated fibreboard - Determination of grammage of the component papers after separation
- ISO-3689 - Paper and board - Determination of bursting strength after immersion in water
- ISO-3781 - Paper and board - Determination of tensile strength after immersion in water
- ISO-3783 - Paper and board - Determination of resistance to picking - Accelerated speed method using the IGT-type tester (electric model)
- ISO-4046-1 - Paper, board, pulps and related terms - Vocabulary - Part 1: Alphabetical index
- ISO-4046-4 - Paper, board, pulps and related terms - Vocabulary - Part 4: Paper and board grades and converted products
- ISO-4046-5 - Paper, board, pulps and related terms - Vocabulary - Part 5: Properties of pulp, paper and board
- ISO-4094 - Paper, board and pulps - General requirements for the competence of laboratories authorized for the issue of optical reference transfer standards of level 3
- ISO-534 - Paper and board - Determination of thickness, density and specific volume
- ISO-535 - Paper and board - Determination of water absorptiveness - Cobb method
- ISO-536 - Paper and board - Determination of grammage
- ISO-5626 - Paper -- Determination of folding endurance
- ISO-5627 - Paper and board -- Determination of smoothness (Bekk method)
- ISO-5628 - Paper and board - Determination of bending stiffness - General principles for two-point, three-point and four-point methods
- ISO-5629 - Paper and board - Determination of bending stiffness - Resonance method
- ISO-5630-1 - Paper and board -- Accelerated ageing -- Part 1: Dry heat treatment at 105 degrees C
- ISO-5630-3 - Paper and board -- Accelerated ageing -- Part 3: Moist heat treatment at 80 degrees C and 65 % relative humidity
- ISO-5630-4 - Paper and board -- Accelerated ageing -- Part 4: Dry heat treatment at 120 or 150 degrees C
- ISO-5630-5 - Paper and board - Accelerated ageing - Part 5: Exposure to elevated temperature at 100 degrees C
- ISO-5630-6 - Paper and board - Accelerated ageing - Part 6: Exposure to atmospheric pollution (nitrogen dioxide)
- ISO-5630-7 - Paper and board - Accelerated ageing - Part 7: Exposure to light
- ISO-5631-1 - Paper and board - Determination of colour by diffuse reflectance - Part 1: Indoor daylight conditions (C/2°)
- ISO-5631-2 - Paper and board - Determination of colour by diffuse reflectance - Part 2: Outdoor daylight conditions (D65/10°)
- ISO-5631-3 - Paper and board - Determination of colour by diffuse reflectance - Part 3: Indoor illumination conditions (D50/2°)
- ISO-5633 - Paper and board -- Determination of resistance to water penetration
- ISO-5635 - Paper -- Measurement of dimensional change after immersion in water
- ISO-5636-1 - Paper and board -- Determination of air permeance (medium range) -- Part 1: General method
- ISO-5636-3 - Paper and board - Determination of air permeance (medium range) - Part 3: Bendtsen method
- ISO-5636-4 - Paper and board - Determination of air permeance (medium range) - Part 4: Sheffield method
- ISO-5636-5 - Paper and board - Determination of air permeance (medium range) - Part 5: Gurley method
- ISO-5636-6 - Paper and board - Determination of air permeance (medium range) - Part 6: Oken method
- ISO-5637 - Paper and board - Determination of water absorption after immersion in water
- ISO-5638 - Solid fibreboard -- Determination of grammage of single layers
- ISO-5647 - Paper and board - Determination of titanium dioxide content
- ISO-638 - Paper, board and pulps - Determination of dry matter content - Oven-drying method
- ISO-638-1 - Paper, board, pulps and cellulosic nanomaterials - Determination of dry matter content by oven-drying method - Part 1: Materials in solid form
- ISO-638-2 - Paper, board, pulps and cellulosic nanomaterials - Determination of dry matter content by oven-drying method - Part 2: Suspensions of cellulosic nanomaterials
- ISO-6587 - Paper, board and pulps - Determination of conductivity of aqueous extracts
- ISO-6588-1 - Paper, board and pulps - Determination of pH of aqueous extracts - Part 1: Cold extraction
- ISO-6588-2 - Paper, board and pulps - Determination of pH of aqueous extracts - Part 2: Hot extraction
- ISO-7263 - Corrugating medium - Determination of the flat crush resistance after laboratory fluting
- ISO-7763 - Testing of paper and board - Compressive strength of a sample held in S-shape
- ISO-777 - Paper, board and pulp - Determination of acid-soluble calcium
- ISO-778 - Paper, board and pulp - Determination of acid-soluble copper
- ISO-8226-1 - Paper and board -- Measurement of hygroexpansivity -- Part 1: Hygroexpansivity up to a maximum relative humidity of 68 %
- ISO-8226-2 - Paper and board -- Measurement of hygroexpansivity -- Part 2: Hygroexpansivity up to a maximum relative humidity of 86 %
- ISO-8254-1 - Paper and board - Measurement of specular gloss - Part 1: 75 degree gloss with a converging beam, TAPPI method
- ISO-8254-2 - Paper and board - Measurement of specular gloss - Part 2: 75 degree gloss with a parallel beam, DIN method
- ISO-8254-3 - Paper and board - Measurement of specular gloss - Part 3: 20 degree gloss with a converging beam, TAPPI method
- ISO-8784-1 - Pulp, paper and board - Microbiological examination - Part 1: Enumeration of bacteria and bacterial spores based on disintegration
- ISO-8784-2 - Pulp, paper and board - Microbiological examination - Part 2: Enumeration of bacteria, yeast and mould on surface
- ISO-8784-3 - Pulp, paper and board - Microbiological examination - Part 3: Enumeration of yeast and mould based on disintegration
- ISO-8787 - Paper and board -- Determination of capillary rise -- Klemm method
- ISO-8791-1 - Paper and board -- Determination of roughness/smoothness (air leak methods) -- Part 1: General method
- ISO-8791-2 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 2: Bendtsen method
- ISO-8791-3 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 3: Sheffield method
- ISO-8791-4 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 4: Print-surf method
- ISO-8791-5 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 5: Oken method
- ISO-9184-1 - Paper, board and pulps - Fibre furnish analysis - Part 1: General method
- ISO-9184-2 - Paper, board and pulps -- Fibre furnish analysis -- Part 2: Staining guide
- ISO-9184-3 - Paper, board and pulps -- Fibre furnish analysis -- Part 3: Herzberg staining test
- ISO-9184-4 - Paper, board and pulps -- Fibre furnish analysis -- Part 4: Graff C staining test
- ISO-9184-5 - Paper, board and pulps -- Fibre furnish analysis -- Part 5: Lofton-Merritt staining test (modification of Wisbar)
- ISO-9184-6 - Paper, board and pulps -- Fibre furnish analysis -- Part 6: Determination of fibre coarseness
- ISO-9184-7 - Paper, board and pulps -- Fibre furnish analysis -- Part 7: Determination of weight factor
- ISO-9197 - Paper, board and pulps - Determination of water-soluble chlorides
- ISO-9198 - Paper, board and pulp - Determination of water-soluble sulfates
- ISO-9416 - Paper - Determination of light scattering and absorption coefficients (using Kubelka-Munk theory)
- ISO-9706 - Information and documentation -- Paper for documents -- Requirements for permanence
- ISO-9895 - Paper and board - Compressive strength - Short-span test
- ISO-9932 - Paper and board - Determination of water vapour transmission rate of sheet materials - Dynamic sweep and static gas methods
Other SDOs:
- AS/NZS-1301.422S - Methods of Test for Pulp & Paper - Determination of the Ph Value of Aqueous Extracts O
- DIN-53107 - Testing of paper and board - Determination of the smoothness by the Bekk method
- DIN-EN-1104 - Paper & Board Intended To Come Into Contact With Foodstuffs, Determination of the Tran
- DIN-EN-1230-2 - Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2: Off-flavour (taint); German version EN 1230-2:2009
- DIN-EN-12497 - Paper & Board, Paper & Board Intended To Come Into Contact With Foodstuffs, Determinat
- DIN-EN-12498 - Paper & Board, Paper & Board Intended To Come Into Contact With Foodstuffs, Determinat
- DIN-EN-14719 - Pulp, Paper & Board, Determination of the Diisopropylnaphthalene (Dipn) Content by Sol
- DIN-EN-646 - Paper & Board Intended To Come Into Contact With Foodstuffs - Determination of Colour
- DIN-EN-648 - Paper & Board Intended To Come Into Contact With Foodstuffs - Determination of the Fa
- DIN-EN-ISO-12625-6 - Tissue paper and tissue products - Part 6: Determination of grammage
- DIN-EN-ISO-15320 - Pulp, paper and board - Determination of pentachlorophenol in an aqueous extract
- DIN-EN-ISO-2758 - Paper - Determination of bursting strength
- DIN-EN-ISO-2759 - Board - Determination of bursting strength
- DIN-EN-ISO-3037 - Corrugated fibreboard - Determination of edgewise crush resistance (unwaxed edge method) (ISO 3037:2013)
- DIN-EN-ISO-534 - Paper and board - Determination of thickness, density and specific volume
- DIN-EN-ISO-8254-1 - Part 1: 75 Degree Gloss With a Converging Beam, TAPPI Method, Paper & Board - Measurem
- DIN-EN-ISO-8254-2 - Paper and board - Measurement of specular gloss - Part 2: 75 Degrees gloss with a parallel beam, DIN method
- DIN-ISO-1924-3 - Part 3: Constant Rate of Elongation Method (100 mm/Min), Paper & Board - Determination
- EN-1104 - Paper & Board Intended To Come Into Contact With Foodstuffs, Determination of Transfer
- EN-1230-1 - Part 1: Odour, Paper & Board Intended To Come Into Contact With Foodstuffs - Sensory A
- EN-1230-2 - Part 2: off-Flavour (Taint), Paper & Board Intended To Come Into Contact With Foodstu
- EN-12497 - Paper & Board, Paper & Board Intended To Come Into Contact With Foodstuffs, Determinat
- EN-12498 - Paper & Board, Paper & Board Intended To Come Into Contact With Foodstuffs, Determinat
- EN-13676 - Polymer Coated Paper & Board Intended for Food Contact, Detection of Pinholes
- EN-14719 - Pulp, Paper & Board, Determination of the Diisoproplynaphthalene (Dipn) Content by Sol
- EN-1541 - Paper & Board Intended To Come Into Contact With Foostuffs,Determination of Formaldeh
- EN-15845 - Paper & Board - Determination of the Cytotoxicity of Aqueous Extracts
- EN-16418 - Paper and board - Determination of the cytotoxicity of aqueous extracts using a metabolically competent hepatoma cell line (HepG2)
- EN-16453 - Pulp, paper and paperboard - Determination of phthalates in extracts from paper and paperboard
- EN-17085 - Paper and board - Sampling procedures for paper and board for recycling
- EN-20187 - Paper, Board & Pulps - Standard Atmosphere for Conditioning& Testing & Procedure For
- EN-21974 - Determination of Tearing Resistance of Paper (Elmendorf Method)
- EN-23035 - Single-Faced & Single-Wall Corrugated Fibreboard, Determination of Flat Crush Resistan
- EN-643 - Paper and board - European list of standard grades of paper and board for recycling
- EN-646 - Paper & Board Intended To Come Into Contact With Foodstuffs - Determination of Colour
- EN-648 - Paper & Board Intended To Come Into Contact With Foodstuffs, Determination of the Fast
- EN-920 - Paper and board intended to come into contact with foodstuffs - Determination of dry matter content in an aqueous extract
- EN-ISO-12625-1 - Tissue paper and tissue products - Part 1: General guidance on terms
- EN-ISO-12625-10 - Part 10: Determination of Demand Water Absorption Rate & Capacity, Under Controlled Hy
- EN-ISO-12625-11 - Tissue paper and tissue products - Part 11: Determination of wet ball burst strength (ISO 12625-11:2012)
- EN-ISO-12625-15 - Tissue paper and tissue products - Part 15: Determination of optical properties - Measurement of brightness and colour with C/2 Degrees (indoor daylight) illuminant
- EN-ISO-12625-16 - Tissue paper and tissue products - Part 16: Determination of optical properties - Opacity (paper backing) - Diffuse reflectance method
- EN-ISO-12625-3 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density and bulk (ISO 12625-3:2014)
- EN-ISO-12625-6 - Tissue paper and tissue products - Part 6: Determination of grammage
- EN-ISO-12625-7 - Tissue paper and tissue products - Part 7: Determination of optical properties - Measurement of brightness and colour with D65/10 Degrees (outdoor daylight)
- EN-ISO-12625-8 - Part 8: Water-Absorption Time & Water-Absorption Capacity, Basket-Immersion Test Metho
- EN-ISO-12625-9 - Tissue paper and tissue products - Part 9: Determination of ball burst strength
- EN-ISO-15320 - Pulp, paper and board - Determination of pentachlorophenol in an aqueous extract
- EN-ISO-186 - Paper & Board, Sampling To Determine Average Quality
- EN-ISO-1924-2 - Paper & Board, Determination of Tensile Properties, Constant Rate of Elongation Method
- EN-ISO-1974 - Paper - Determination of tearing resistance - Elmendorf method (ISO 1974:2012)
- EN-ISO-217 - Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction (ISO 217:2013)
- EN-ISO-2758 - Paper - Determination of bursting strength
- EN-ISO-2759 - Board - Determination of bursting strength (ISO 2759:2014)
- EN-ISO-287 - Paper & Board, Determination of Moisture Content of a Lot, Oven-Drying Method
- EN-ISO-3035 - Corrugated fibreboard - Determination of flat crush resistance
- EN-ISO-534 - Paper and board - Determination of thickness, density and specific volume
- EN-ISO-535 - Paper and board - Determination of water absorptiveness - Cobb method (ISO 535:2014)
- EN-ISO-536 - Paper and board - Determination of grammage (ISO 536:2012)
- EN-ISO-638 - Paper, Board & Pulps - Determination of Dry Matter Content - Oven-Drying Method
- EN-ISO-7263 - Corrugating medium - Determination of the flat crush resistance after laboratory fluting (ISO 7263:2011)
- EN-ISO-8254-1 - Part 1: 75 Degree Gloss With a Converging Beam, TAPPI Method, Paper & Board - Measurem
- EN-ISO-8254-2 - Paper and board - Measurement of specular gloss - Part 2: 75 degree gloss with a parallel beam, DIN method
- EN-ISO-9706 - Information & Documentation - Paper for Documents - Requirements for Permanence
- JIS-P-8124 - Paper and board -- Determination of grammage
- JIS-P-8251 - Paper, board and pulps -- Determination of residue (ash) on ignition at 525 degrees C
- JIS-P-8252 - Paper, board and pulps -- Determination of residue (ash) on ignition at 900 degrees C
- JIS-Z-1516 - Corrugated fiberboards for shipping containers
- SIS-CEN-ISO/TS-16775 - Packaging for terminally sterilized medical devices - Guidance on the application of ISO 11607-1 and ISO 11607-2 (ISO/TS 16775:2021)
- SIS-CEN/TR-15645-1 - Paper and board intended to come into contact with foodstuffs - Calibration of the off-flavour test - Part 1: Odour
- SIS-CEN/TR-15645-2 - Paper and board intended to come into contact with foodstuffs - Calibration of the off-flavour test - Part 2: Fatty food
- SIS-CEN/TR-15645-3 - Paper and board intended to come into contact with foodstuffs - Calibration of the off-flavour test - Part 3: Dry food
- SIS-CEN/TS-17830 - Paper and board - Guidance on the application of Term 2.2 "Prohibited materials" of EN 643:2014
- SIS-EN-ISO-11607-1 - Packaging for terminally sterilized medical devices - Part 1: Requirements for materials, sterile barrier systems and packaging systems (ISO 11607-1:2006)
- SIS-EN-ISO-11607-2 - Packaging for terminally sterilized medical devices - Part 2: Validation requirements for forming, sealing and assembly processes (ISO 11607-2:2006)
- SIS-ISO-23885 - Paper, board and graphic technology Determination of the coating strength in the inner fold (ISO/TS 23885:2022, IDT)
- SIS-ISO/TR-10688 - Paper, board and pulps - Basic terms and equations for optical properties (ISO/TR 10688:2015, IDT)
- SIS-ISO/TR-25477 - Paper, board and pulps - Basic guidelines for image analysis measurements
- SIS-ISO/TS-17958 - Paper and board - Determination of fracture toughness - Constant rate of elongation method (1,7 mm/s) (ISO/TS 17958:2013, IDT)
- SIS-ISO/TS-19857 - Paper, Board and Printing inks - Printability - Laboratory test method for offset ink setting (ISO/TS 19857:2021)
- SIS-ISO/TS-20460 - Paper and board - Automated on-line testing - Metrological comparability between standardized measurements and output of on-line gauges (ISO/TS 20460:2015, IDT)
- SIS-ISO/TS-24498 - Paper, board and pulps - Estimation of uncertainty for test methods by interlaboratory comparisons (ISO/TS 24498:2022, IDT)
- SS-152010 - Pulp, paper and board - Recommendations and guidelines for the design of technical specifications
- SS-EN-1076 - Workplace exposure - Procedures for measuring gases and vapours using pumped samplers - Requirements and test methods
- SS-EN-1104 - Paper and board intended to come into contact with foodstuffs - Determination of the transfer of antimicrobial constituents
- SS-EN-1230-1 - Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 1: Odour
- SS-EN-1230-2 - Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2: Off-flavour (taint)
- SS-EN-12497 - Paper and board - Paper and board intended to come into contact with foodstuffs - Determination of mercury in an aqueous extract
- SS-EN-12498 - Paper and board - Paper and board intended to come into contact with foodstuffs - Determination of cadmium, chromium and lead in an aqueous extract
- SS-EN-14086 - Paper and board - Measurement of specular gloss - 45° gloss with a parallel beam, DIN method
- SS-EN-14719 - Pulp, paper and board - Determination of the Diisopropylnaphthalene (DIPN) content by solvent extraction
- SS-EN-1541 - Paper and board intended to come into contact with foodstuffs - Determination of formaldehyde in an aqueous extract
- SS-EN-15845 - Paper and board - Determination of the cytotoxicity of aqueous extracts
- SS-EN-16418 - Paper and board - Determination of the cytotoxicity of aqueous extracts using a metabolically competent hepatoma cell line (HepG2)
- SS-EN-16453 - Pulp, paper and paperboard - Determination of phthalates in extracts from paper and paperboard
- SS-EN-17085 - Paper and board - Sampling procedures for paper and board for recycling
- SS-EN-17163 - Pulp, paper and board - Determination of primary aromatic amines (PAA) in a water extract by a LC-MS method
- SS-EN-17545 - Paper and board - Determination of composition of paper and board for recycling by gravimetric analysis
- SS-EN-20187 - Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples (ISO 187:1990)
- SS-EN-20287 - Paper and board - Determination of moisture content - Oven-drying method (ISO 287:1985)
- SS-EN-20534 - Paper and board - Determination of thickness and apparent bulk density or apparent sheet density (ISO 534:1988)
- SS-EN-20535 - Paper and board - Determination of water absorptiveness - Cobb method (ISO 535:1991)
- SS-EN-21974 - Paper - Determination of tearing resistance (Elmendorf method) (ISO 1974:1990)
- SS-EN-23035 - Single-faced and single-wall corrugated fibreboard - Determination of flat crush resistance (ISO 3035:1982)
- SS-EN-25651 - Paper, board and pulps - Units for expressing properties
- SS-EN-643 - Paper and board - European list of standard grades of paper and board for recycling
- SS-EN-644 - Paper - Untrimmed sizes - Primary range and supplementary range designation and tolerances, expression of direction of manufacture
- SS-EN-645 - Paper and boards intended to come into contact with foodstuffs - Preparation of a cold water extract
- SS-EN-646 - Paper and board intended to come into contact with foodstuffs - Determination of colour fastness of dyed paper and board
- SS-EN-647 - Paper and board intended to come into contact with foodstuffs - Preparation of a hot water extract
- SS-EN-648 - Paper and board intended to come into contact with foodstuffs - Determination of the fastness of fluorescent whitened paper and board
- SS-EN-868-1 - Packaging materials and systems for medical devices which are to be sterilized - Part 1: General requirements and test methods
- SS-EN-920 - Paper and board intended to come into contact with foodstuffs - Determination of dry matter content in an aqueous extract
- SS-EN-ISO-11607-1 - Packaging for terminally sterilized medical devices - Part 1: Requirements for materials, sterile barrier systems and packaging systems (ISO 11607-1:2019)
- SS-EN-ISO-11607-1-AM11 - Packaging for terminally sterilized medical devices - Part 1: Requirements for materials, sterile barrier systems and packaging systems (ISO 11607-1:2019)
- SS-EN-ISO-12625-1 - Tissue paper and tissue products - Part 1: General guidance on terms (ISO 12625-1:2011)
- SS-EN-ISO-12625-11 - Tissue paper and tissue products - Part 11: Determination of wet ball burst strength (ISO 12625-11:2019)
- SS-EN-ISO-12625-12 - Tissue paper and tissue products - Part 12: Determination of tensile strength of perforated lines - Calculation of perforation efficiency (ISO 12625-12:2010)
- SS-EN-ISO-12625-15 - Tissue paper and tissue products - Part 15: Determination of optical properties - Measurement of brightness and colour with C/2° (indoor daylight) illuminant (ISO 12625-15:2022)
- SS-EN-ISO-12625-16 - Tissue paper and tissue products - Part 16: Determination of optical properties - Opacity (paper backing) - Diffuse reflectance method (ISO 12625-16:2015)
- SS-EN-ISO-12625-3 - Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density and bulk (ISO 12625-3:2014)
- SS-EN-ISO-12625-4 - Tissue paper and tissue products - Part 4: Determination of tensile strength, stretch at maximum force and tensile energy absorption (ISO 12625-4:2022)
- SS-EN-ISO-12625-5 - Tissue paper and tissue products - Part 5: Determination of wet tensile strength (ISO 12625-5:2016)
- SS-EN-ISO-12625-6 - Tissue paper and tissue products - Part 6: Determination of grammage (ISO 12625-6:2016)
- SS-EN-ISO-12625-7 - Tissue paper and tissue products - Part 7: Determination of optical properties - Measurement of brightness and colour with D65/10° (outdoor daylight) (ISO 12625-7:2021)
- SS-EN-ISO-12625-8 - Tissue paper and tissue products - Part 8: Water-absorption time and water-absorption capacity, basket- immersion test method (ISO 12625-8:2010)
- SS-EN-ISO-12625-9 - Tissue paper and tissue products - Part 9: Determination of ball burst strength (ISO 12625-9:2015)
- SS-EN-ISO-15318 - Pulp, paper and board - Determination of 7 specified polychlorinated biphenyls (PCB) ( ISO 15318:1999)
- SS-EN-ISO-15320 - Pulp, paper and board - Determination of pentachlorophenol in an aqueous extract (ISO 15320:2011)
- SS-EN-ISO-15755 - Paper and board - Estimation of contraries
- SS-EN-ISO-186 - Paper and board - Sampling to determine average quality (ISO 186:2002)
- SS-EN-ISO-187 - Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples (ISO 187:2022)
- SS-EN-ISO-1924-2 - Paper and board - Determination of tensile properties - Part 2: Constant rate of elongation method (20 mm/min) (ISO 1924-2:2008)
- SS-EN-ISO-1974 - Paper - Determination of tearing resistance - Elmendorf method (ISO 1974:2012)
- SS-EN-ISO-217 - Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction (ISO 217:2013)
- SS-EN-ISO-2758 - Paper - Determination of bursting strength (ISO 2758:2014)
- SS-EN-ISO-2759 - Board - Determination of bursting strength (ISO 2759:2014)
- SS-EN-ISO-287 - Paper and board - Determination of moisture content of a lot - Oven-drying method (ISO 287:2017)
- SS-EN-ISO-3035 - Corrugated fibreboard - Determination of flat crush resistance (ISO 3035:2011)
- SS-EN-ISO-3037 - Corrugated fibreboard - Determination of edgewise crush resistance (non-waxed edge method) (ISO 3037:2022)
- SS-EN-ISO-5267-1 - Pulps - Determination of drainability - Part 1: Schopper-Riegler method (ISO 5267-1:1999)
- SS-EN-ISO-534 - Paper and board - Determination of thickness, density and specific volume (ISO 534:2011)
- SS-EN-ISO-535 - Paper and board - Determination of water absorptiveness - Cobb method (ISO 535:2023)
- SS-EN-ISO-536 - Paper and board - Determination of grammage (ISO 536:2019)
- SS-EN-ISO-638 - Paper, board and pulps - Determination of dry matter content - Oven-drying method (ISO 638:2008)
- SS-EN-ISO-638-1 - Paper, board, pulps and cellulosic nanomaterials - Determination of dry matter content by oven-drying method - Part 1: Materials in solid form (ISO 638-1:2021)
- SS-EN-ISO-638-2 - Paper, board, pulps and cellulosic nanomaterials - Determination of dry matter content by oven-drying method - Part 2: Suspensions of cellulosic nanomaterials (ISO 638-2:2022)
- SS-EN-ISO-7263 - Corrugating medium - Determination of the flat crush resistance after laboratory fluting (ISO 7263:2011)
- SS-EN-ISO-7263-1 - Corrugating medium - Determination of the flat crush resistance after laboratory fluting - Part 1: A-flute (ISO 7263-1:2018)
- SS-EN-ISO-7263-2 - Corrugating medium - Determination of the flat crush resistance after laboratory fluting - Part 2: B-flute (ISO 7263-2:2018)
- SS-EN-ISO-8254-1 - Paper and board - Measurement of specular gloss - Part 1: 75 degree gloss with a converging beam, TAPPI method (ISO 8254-1:2009)
- SS-EN-ISO-8254-2 - Paper and board - Measurement of specular gloss - Part 2: 75 degree gloss with a parallel beam, DIN method (ISO 8254-2:2016)
- SS-EN-ISO-9706 - Information and documentation - Paper for documents - Requirements for permanence (ISO 9706:1994)
- SS-ENV-12497 - See the swedish title
- SS-ENV-1798 - Paper and board intended to come into contact with foodstuffs - Determination of 7 specified polychlorinated biphenyls (PCB)
- SS-ISO-10716 - Paper and board - Determination of alkali reserve (ISO 10716:2022, IDT)
- SS-ISO-10775 - Paper, board and pulps - Determination of cadmium content - Atomic absorption spectrometric method (ISO 10775:2013, IDT)
- SS-ISO-11093-1 - Paper and board - Testing of cores - Part 1: Sampling (ISO 11093-1:1994, IDT)
- SS-ISO-11093-2 - Paper and board - Testing of cores - Part 2: Conditioning of test samples (ISO 11093-2:1994, IDT)
- SS-ISO-11093-3 - Paper and board - Testing of cores - Part 3: Determination of moisture content using the ovendrying method (ISO 11093-3:1994, IDT)
- SS-ISO-11093-4 - Paper and board - Testing of cores - Part 4: Measurement of dimensions (ISO 11093-4:2022, IDT)
- SS-ISO-11093-5 - Paper and board - Testing of cores - Part 5: Determination of characteristics of concentric rotation (ISO 11093-5:2016, IDT)
- SS-ISO-11093-6 - Paper and board - Testing of cores - Part 6: Determination of bending strength by the three-point method (ISO 11093-6:2005, IDT)
- SS-ISO-11093-7 - Paper and board - Testing of cores - Part 7: Determination of flexural modulus by the three-point method (ISO 11093-7:2011, IDT)
- SS-ISO-11093-8 - Paper and board - Testing of cores - Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis (ISO 11093-8:2017, IDT)
- SS-ISO-11093-9 - Paper and board - Testing of cores - Part 9: Determination of flat crush resistance (ISO 11093-9:2019, IDT)
- SS-ISO-11108 - Information and documentation - Archival paper - Requirements for performance and durability
- SS-ISO-11475 - Paper and board - Determination of CIE whiteness, D65/10 degrees (outdoor daylight) (ISO 11475:2017, IDT)
- SS-ISO-11476 - Paper and board - Determination of CIE whiteness, C/2° (indoor illumination conditions) (ISO 11476:2016, IDT)
- SS-ISO-11480 - Pulp, paper and board - Determination of total chlorine and organically bound chlorine (ISO 11480:2017, IDT)
- SS-ISO-11556 - Paper and board - Determination of curl using a single vertically suspended test piece (ISO 11556:2005, IDT)
- SS-ISO-12192 - Paper and board - Determination of compressive strength - Ring crush method (ISO 12192:2011, IDT)
- SS-ISO-12830 - Paper, board, pulps and cellulose nanomaterials - Determination of acid-soluble magnesium, calcium, manganese, iron, copper, sodium and potassium (ISO 12830:2019, IDT)
- SS-ISO-13542 - Paper and board - Specification for internal diameters of cores for reels (ISO 13542:2006, IDT)
- SS-ISO-13821 - Corrugated fibreboard - Determination of edgewise crush resistance - Waxed edge method (ISO 13821:2020, IDT)
- SS-ISO-14968 - Paper and board - Cut-size office paper - Measurement of curl in a pack of sheets (ISO 14968:2022, IDT)
- SS-ISO-15359 - Paper and board - Determination of the static and kinetic coefficients of friction - Horizontal plane method (ISO 15359:1999, IDT)
- SS-ISO-15754 - Paper and board - Determination of z-directional tensile strength (ISO 15754:2009, IDT)
- SS-ISO-16245 - Information and documentation Boxes, file covers and other enclosures, made from cellulosic materials, for storage of paper and parchment documents (ISO 16245:2023, IDT)
- SS-ISO-16260 - Paper and board - Determination of internal bond strength (ISO 16260:2016,IDT)
- SS-ISO-16532-1 - Paper and board - Determination of grease resistance - Part 1: Permeability test (ISO 16532-1:2008, IDT)
- SS-ISO-16532-2 - Paper and board - Determination of grease resistance - Part 2: Surface repellency test (ISO 16532-2:2007, IDT)
- SS-ISO-16532-3 - Paper and board - Determination of grease resistance - Part 3: Turpentine test for voids in glassine and greaseproof papers (ISO 16532-3:2010, IDT)
- SS-ISO-16945 - Corrugating medium - Determination of the edge crush resistance after laboratory fluting (ISO 16945:2014, IDT)
- SS-ISO-1762 - Paper, board and pulps - Determination of residue (ash) on ignition at 525° C (ISO 1762:2015, IDT)
- SS-ISO-17812 - Paper, board and pulps - Determination of total magnesium, total calcium, total manganese, total iron and total copper (ISO 17812:2007, IDT)
- SS-ISO-18522 - Paper and board - Automated off-line testing of physical properties for CD (cross direction) profiles (ISO 18522:2016, IDT)
- SS-ISO-1924-3 - Paper and board - Determination of tensile properties - Part 3: Constant rate of elongation method (100 mm/min) (ISO 1924-3:2005, IDT)
- SS-ISO-20494 - Paper - Requirements for stability for general, graphic applications (ISO 20494:2017, IDT)
- SS-ISO-2144 - Paper, board, pulps and cellulose nanomaterials - Determination of residue (ash content) on ignition at 900 °C (ISO 2144:2019, IDT)
- SS-ISO-21993 - Paper and pulp - Deinkability test for printed paper products (ISO 21993:2020, IDT)
- SS-ISO-22754 - Pulp and paper - Determination of the effective residual ink concentration (ERIC number) by infrared reflectance measurement (ISO 22754:2008, IDT)
- SS-ISO-22891 - Paper - Determination of transmittance by diffuse reflectance measurement (ISO 22891:2013, IDT)
- SS-ISO-2469 - Paper, board and pulps - Measurement of diffuse radiance factor (diffuse reflectance factor) (ISO 2469:2014, IDT)
- SS-ISO-2470 - Paper, board and pulps - Measurement of diffuse blue reflectance factor (ISO brightness)
- SS-ISO-2470-1 - Paper, board and pulps - Measurement of diffuse blue reflectance factor - Part 1: Indoor daylight conditions (ISO brightness) (ISO 2470-1:2016, IDT)
- SS-ISO-2470-2 - Paper, board and pulps - Measurement of diffuse blue reflectance factor - Part 2: Outdoor daylight conditions (D65 brightness) (ISO 2470-2:2008, IDT)
- SS-ISO-2471 - Paper and board - Determination of opacity (paper backing) - Diffuse reflectance method (ISO 2471:2008, IDT)
- SS-ISO-2493-1 - Paper and board - Determination of bending resistance - Part 1: Constant rate of deflection (ISO 2493-1:2010, IDT)
- SS-ISO-2493-2 - Paper and board - Determination of resistance to bending - Part 2: Taber-type tester (ISO 2493-2:2020, IDT)
- SS-ISO-2528 - Sheet materials - Determination of water vapour transmission rate - Gravimetric (dish) method (ISO 2528:2017, IDT)
- SS-ISO-29681 - Paper, board and pulps - Determination of pH of salted water extracts (ISO 29681:2009, IDT)
- SS-ISO-3034 - Corrugated fibreboard - Determination of single sheet thickness (ISO 3034:2011, IDT)
- SS-ISO-3036 - Board - Determination of puncture resistance (ISO 3036:1975, IDT)
- SS-ISO-3039 - Corrugated fibreboard - Determination of grammage of the component papers after separation (ISO 3039:2010, IDT)
- SS-ISO-3689 - Paper and board - Determination of bursting strength after immersion in water (ISO 3689:1983, IDT)
- SS-ISO-3781 - Paper and board - Determination of tensile strength after immersion in water (ISO 3781:2011, IDT)
- SS-ISO-3783 - Paper and board - Determination of resistance to picking - Accelerated speed method using the IGT-type tester (electric model) (ISO 3783:2006, IDT)
- SS-ISO-4046-1 - Paper, board, pulps and related terms - Vocabulary - Part 1: Alphabetical index (ISO 4046-1:2016, IDT)
- SS-ISO-4046-4 - Paper, board, pulps and related terms - Vocabulary - Part 4: Paper and board grades and converted products (ISO 4046-4:2016, IDT)
- SS-ISO-4046-5 - Paper, board, pulps and related terms - Vocabulary - Part 5: Properties of pulp, paper and board (ISO 4046-5:2016, IDT)
- SS-ISO-4094 - Paper, board and pulps - General requirements for the competence of laboratories authorized for the issue of optical reference transfer standards of level 3 (ISO 4094:2017, IDT)
- SS-ISO-5626 - Paper - Determination of folding endurance (ISO 5626:1993, IDT)
- SS-ISO-5627 - Paper and board - Determination of smoothness (Bekk method) (ISO 5627:1995, IDT)
- SS-ISO-5628 - Paper and board - Determination of bending stiffness - General principles for two-point, three-point and four-point methods (ISO 5628:2019, IDT)
- SS-ISO-5629 - Paper and board - Determination of bending stiffness - Resonance method (ISO 5629:2017, IDT)
- SS-ISO-5630-1 - Paper and board - Accelerated ageing - Part 1: Dry heat treatment at 105 degrees C (ISO 5630-1:1991, IDT)
- SS-ISO-5630-3 - Paper and board - Accelerated ageing - Part 3: Moist heat treatment at 80 degrees C and 65 % relative humidity (ISO 5630-3:1996, IDT)
- SS-ISO-5630-4 - Paper and board - Accelerated ageing - Part 4: Dry heat treatment at 120 or 150 degrees C (ISO 5630-4:1986, IDT)
- SS-ISO-5630-5 - Paper and board - Accelerated ageing - Part 5: Exposure to elevated temperature at 100 degrees C (ISO 5630-5:2008, IDT)
- SS-ISO-5630-6 - Paper and board - Accelerated ageing - Part 6: Exposure to atmospheric pollution (nitorgen dioxide) (ISO 5630-6:2009, IDT)
- SS-ISO-5630-7 - Paper and board - Accelerated ageing - Part 7: Exposure to light (ISO 5630-7:2014, IDT)
- SS-ISO-5631-1 - Paper and board - Determination of colour by diffuse reflectance - Part 1: Indoor daylight conditions (C/2°) (ISO 5631-1:2022, IDT)
- SS-ISO-5631-2 - Paper and board - Determination of colour by diffuse reflectance - Part 2: Outdoor daylight conditions (D65/10°) (ISO 5631-2:2022, IDT)
- SS-ISO-5631-3 - Paper and board - Determination of colour by diffuse reflectance - Part 3: Indoor illumination conditions (D50/2°) (ISO 5631-3:2022, IDT)
- SS-ISO-5633 - Paper and board - Determination of resistance to water penetration (ISO 5633:1983, IDT)
- SS-ISO-5635 - Paper - Measurement of dimensional change after immersion in water (ISO 5635:1978, IDT)
- SS-ISO-5636-3 - Paper and board - Determination of air permeance (medium range) - Part 3: Bendtsen method (ISO 5636-3:2013, IDT)
- SS-ISO-5636-4 - Paper and board - Determination of air permeance (medium range) - Part 4: Sheffield method (ISO 5636-4:2013, IDT)
- SS-ISO-5636-5 - Paper and board - Determination of air permeance (medium range) - Part 5: Gurley method (ISO 5636-5:2013, IDT)
- SS-ISO-5636-6 - Paper and board - Determination of air permeance (medium range) - Part 6: Oken method (ISO 5636-6:2015, IDT)
- SS-ISO-5637 - Paper and board - Determination of water absorption after immersion in water (ISO 5637:1989, IDT)
- SS-ISO-5638 - Solid fibreboard - Determination of grammage of single layers (ISO 5638:1978, IDT)
- SS-ISO-5647 - Paper and board - Determination of titanium dioxide content (ISO 5647:2019, IDT)
- SS-ISO-6588-1 - Paper, board and pulps - Determination of pH of aqueous extracts - Part 1: Cold extraction (ISO 6588-1:2021, IDT)
- SS-ISO-6588-2 - Paper, board and pulps - Determination of pH of aqueous extracts - Part 2: Hot extraction (ISO 6588-2:2021, IDT)
- SS-ISO-8226-1 - Paper and board - Measurement of hygroexpansivity - Part 1: Hygroexpansivity up to a maximum relative humidity of 68 % (ISO 8226-1:1994, IDT)
- SS-ISO-8226-2 - Paper and board - Measurement of hygroexpansivity - Part 2: Hygroexpansivity up to a maximum relative humidity of 86 % (ISO 8226-2:1990, IDT)
- SS-ISO-8254-3 - Paper and board - Measurement of specular gloss - Part 3: 20 degree gloss with a converging beam, TAPPI method (ISO 8254-3:2016, IDT)
- SS-ISO-8784-1 - Pulp, paper and board - Microbiological examination - Part 1: Enumeration of bacteria and bacterial spores based on disintegration (ISO 8784-1:2014, IDT)
- SS-ISO-8784-3 - Pulp, paper and board Microbiological examination Part 3: Enumeration of yeast and mould based on disintegration (ISO 8784-3:2022, IDT)
- SS-ISO-8787 - Paper and board - Determination of capilarry rise - Klemm method (ISO 8787:1986, IDT)
- SS-ISO-8791-1 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 1: General method (ISO 8791-1:1986, IDT)
- SS-ISO-8791-2 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 2: Bendtsen method (ISO 8791-2:2013, IDT)
- SS-ISO-8791-3 - Paper and board - Determination of roughness/smoothness (air leak methods) - Part 3: Sheffield method (ISO 8791-3:2017, IDT)
- SS-ISO-8791-4 - Paper and board Determination of roughness/smoothness (air leak methods) Part 4: Print-surf method (ISO 8791-4:2021, IDT)
- SS-ISO-9184-1 - Paper, board and pulps - Fibre furnish analysis - Part 1: General method (ISO 9184-1:1990, IDT)
- SS-ISO-9184-2 - Paper, board and pulps - Fibre furnish analysis - Part 2: Staining guide (ISO 9184-2:1990, IDT)
- SS-ISO-9184-3 - Paper, board and pulps - Fibre furnish analysis - Part 3: Herzberg staining test (ISO 9184-3:1990, IDT)
- SS-ISO-9184-4 - Paper, board and pulps - Fibre furnish analysis - Part 4: Graff "C" staining test (ISO 9184-4:1990, IDT)
- SS-ISO-9184-5 - Paper, board and pulps - Fibre furnish analysis - Part 5: Lofton-Merritt staining test (modification of Wisbar) (ISO 9184-5:1990, IDT)
- SS-ISO-9184-6 - Paper, board and pulps - Fibre furnish analysis - Part 6: Determination of fibre coarseness (ISO 9184-6:1994, IDT)
- SS-ISO-9184-7 - Paper, board and pulps - Fibre furnish analysis - Part 7: Determination of weight factor (ISO 9184-7:1994, IDT)
- SS-ISO-9197 - Paper, board and pulps - Determination of water-soluble chlorides (ISO 9197:2016, IDT)
- SS-ISO-9198 - Paper, board and pulp - Determination of water-soluble sulfates (ISO 9198:2020, IDT)
- SS-ISO-9416 - Paper - Determination of light scattering and absorption coefficients (using Kubelka-Munk theory) (ISO 9416:2017, IDT)
- SS-ISO-9706 - Information and documentation - Paper for documents - Requirements for permanence
- SS-ISO-9895 - Paper and board - Compressive strength - Short-span test (ISO 9895:2008, IDT)
- SS-ISO-9932 - Paper and board Determination of water vapour transmission rate of sheet materials Dynamic sweep and static gas methods (ISO 9932:2021, IDT)
- SS-ISO/IEC-15459-5 - Information technology - Automatic identification and data capture techniques - Unique identification - Part 5: Individual returnable transport items (RTIs) (ISO/IEC 15459-5:2014, IDT)
- SS-ISO/IEC-15459-6 - Information technology - Automatic identification and data capture techniques - Unique identification - Part 6: Groupings (ISO/IEC 15459-6:2014, IDT)
- TAPPI-TIP-0425-01 - Guidelines for routine periodic inspection and testing of cast iron Yankee and MG dryers
- TAPPI-TIP-0425-07 - Safe and Reliable Start-Up and Shut-Down of Yankee Hood Air Systems
- TAPPI-TIP-0502-01 - Paper Machine Vacuum Selection Factors
- TAPPI-TIP-0502-02 - Determination of Winder Sets Per Reel
- TAPPI-TIP-0502-03 - Reel Diameter for Various Reel Spool & Roll Core Sizes
- TAPPI-TIP-0502-10 - Broke Loss Calculations
- TAPPI-TIP-0502-11 - Weight of Newsprint Rolls
- TAPPI-TIP-0502-12 - Drainage Evaluation by Mass Measurement
- TAPPI-TIP-0502-13 - Retention Definitions
- TAPPI-TIP-0502-14 - Forming Section Monitoring
- TAPPI-TIP-0502-15 - Selection criteria for wet end ceramics
- TAPPI-TIP-0502-16 - Pilot Paper Machines
- TAPPI-TIP-0502-17 - Papermaker's Formulas
- TAPPI-TIP-0502-19 - Use of Ceramics on the Forming Section: Diagnosing & Preventing Forming Fabric Wear
- TAPPI-TIP-0502-20 - Catalog of stock prep pilot plants
- TAPPI-TIP-0508-07 - Conical refining intensity
- TAPPI-TIP-0508-10 - An Introduction To Centrifugal Cleaners