Document Center List of Standards on Safety Of Machinery This Group Includes Standards For General Use
ICS Code 13.110
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
BSI:
- BS-14100 - Control of hazardous energy on machinery. Specification
- BS-14200 - Maintenance of machinery. Specification
- BS-4099-1 - Colours of indicator lights, push-buttons, annunciators and digital readouts
- BS-4099-2 - Colours of indicator lights, push-buttons, annunciators and digital readouts
- BS-4163 - Health and safety for design and technology in educational and similar establishments. Code of practice
- BS-4163-TC - Tracked Changes. Health and safety for design and technology in educational and similar establishments. Code of practice
- BS-4434 - Specification for safety aspects in the design, construction and installation of refrigerating appliances and systems
- BS-6753 - Specification for shotbolts (solenoid operated) for guarding machinery
- BS-7985 - Code of practice for the use of rope access methods for industrial purposes. Recommendations and guidance supplementary to BS ISO 22846
- BS-EN-1005-1 - Safety of machinery. Human physical performance
- BS-EN-1005-2 - Safety of machinery. Human physical performance
- BS-EN-1005-3 - Safety of machinery. Human physical performance
- BS-EN-1005-4 - Safety of machinery. Human physical performance
- BS-EN-1005-5 - Safety of machinery. Human physical performance
- BS-EN-1034-1 - Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines
- BS-EN-1034-13 - Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines
- BS-EN-1037 - Safety of machinery. Prevention of unexpected start-up
- BS-EN-1050 - Safety of machinery. Principles for risk assessment
- BS-EN-1088 - Safety of machinery. Interlocking devices associated with guards. Principles for design and selection
- BS-EN-1093-2 - Safety of machinery. Evaluation of the emission of airborne hazardous substances
- BS-EN-1093-3 - Safety of machinery. Evaluation of the emission of airborne hazardous substances
- BS-EN-1093-4 - Safety of machinery. Evaluation of the emission of airborne hazardous substances
- BS-EN-1127-1 - Explosive atmospheres. Explosion prevention and protection
- BS-EN-12198-1 - Safety of machinery. Assessment and reduction of risks arising from radiation emitted by machinery
- BS-EN-12198-2 - Safety of machinery. Assessment and reduction of risks arising from radiation emitted by machinery
- BS-EN-12198-3 - Safety of machinery. Assessment and reduction of risks arising from radiation emitted by machinery
- BS-EN-12786 - Safety of machinery. Requirements for the drafting of the vibration clauses of safety standards
- BS-EN-12840 - Safety of machine tools. Manually controlled turning machines with or without automatic control
- BS-EN-13478 - Safety of machinery. Fire prevention and protection
- BS-EN-13861 - Safety of machinery. Guidance for the application of ergonomics standards in the design of machinery
- BS-EN-16710-2 - Ergonomics methods
- BS-EN-1760-1 - Safety of machinery. Pressure sensitive protective devices. General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
- BS-EN-1760-2 - Safety of machinery. Pressure sensitive protective devices. General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
- BS-EN-1760-3 - Safety of machinery. Pressure sensitive protective devices. General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices
- BS-EN-1837 - Safety of machinery. Integral lighting of machines
- BS-EN-292-1 - Basic Terminology, Methodology - Safety of Machinery, Basicconcepts, General Principles
- BS-EN-294 - Safety Distances To Prevent Danger Zones Being Reached by the Upper Limbs, Safety of Machi
- BS-EN-349 - Safety of machinery. Minimum gaps to avoid crushing of parts of the human body
- BS-EN-414 - Safety of machinery. Rules for the drafting and presentation of safety standards
- BS-EN-415-11 - Safety of packaging machines
- BS-EN-418 - Safety of machinery. Emergency stop equipment, functional aspects. Principles for design
- BS-EN-457 - Auditory Danger Signals - General Requirements, Design & Testing, Safety of Machinery -
- BS-EN-547-1 - Safety of machinery. Human body measurements
- BS-EN-547-2 - Safety of machinery. Human body measurements
- BS-EN-547-3 - Safety of machinery. Human body measurements
- BS-EN-563 - Safety of machinery. Temperatures of touchable surfaces. Ergonomics data to establish temperature limit values for hot surfaces
- BS-EN-574 - Safety of machinery. Two-hand control devices. Functional aspects. Principles for design
- BS-EN-60204-1 - Safety of machinery. Electrical equipment of machines
- BS-EN-60204-11 - Safety of machinery. Electrical equipment of machines
- BS-EN-60204-31 - Safety of machinery. Electrical equipment of machines
- BS-EN-60204-33 - Safety of machinery. Electrical equipment of machines
- BS-EN-60445-TC - Tracked Changes. Basic and safety principles for man-machine interface, marking and identification. Identification of equipment terminals, conductor terminations and conductors
- BS-EN-60825-1 - Safety of laser products
- BS-EN-61010-2-201 - Safety requirements for electrical equipment for measurement, control and laboratory use. Particular requirements for control equipment
- BS-EN-61010-2-202 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-61285 - Industrial-process control. Safety of analyzer houses
- BS-EN-61285-TC - Tracked Changes. Industrial-process control. Safety of analyzer houses
- BS-EN-61310-1 - Safety of machinery. Indication, marking and actuation
- BS-EN-61310-2 - Safety of machinery. Indication, marking and actuation
- BS-EN-61310-3 - Safety of machinery. Indication, marking and actuation
- BS-EN-614-1 - Safety of machinery. Ergonomic design principles
- BS-EN-614-2 - Safety of machinery. Ergonomic design principles
- BS-EN-61496-1 - Safety of machinery. Electro-sensitive protective equipment
- BS-EN-61496-2 - Safety of machinery. Electro-sensitive protective equipment
- BS-EN-61496-3 - Safety of machinery. Electro-sensitive protective equipment
- BS-EN-61511-1 - Functional safety. Safety instrumented systems for the process industry sector
- BS-EN-61511-2 - Functional safety. Safety instrumented systems for the process industry sector
- BS-EN-61511-3-TC - Tracked Changes. Functional safety. Safety instrumented systems for the process industry sector
- BS-EN-61784-3-18 - Industrial communication networks. Profiles
- BS-EN-61800-5-2 - Adjustable speed electrical power drive systems
- BS-EN-61800-5-2-TC - Tracked Changes. Adjustable speed electrical power drive systems
- BS-EN-62061 - Safety of machinery. Functional safety of safety-related electrical, electronic and programmable electronic control systems
- BS-EN-626-1 - Safety of machinery. Reduction of risks to health from Hazardous substances emitted by machinery. Principles and specifications for machinery manufacturers
- BS-EN-626-2 - Safety of machinery. Reduction of risk to health from hazardous substances emitted by machinery. Methodology leading to verification procedures
- BS-EN-62745 - Safety of machinery. Requirements for cableless control systems of machinery
- BS-EN-811 - Safety of machinery. Safety distances to prevent danger zones being reached by the lower limbs
- BS-EN-842 - Safety of machinery. Visual danger signals. General requirements, design and testing
- BS-EN-894-1 - Safety of machinery. Ergonomics requirements for the design of displays and control actuators
- BS-EN-894-2 - Safety of machinery. Ergonomics requirements for the design of displays and control actuators
- BS-EN-894-4 - Safety of machinery. Ergonomics requirements for design of displays and control actuators
- BS-EN-953 - Safety of machinery. Guards. General requirements for the design and construction of fixed and movable guards
- BS-EN-954-1 - Safety of machinery. Safety related parts of control systems. General principles for design
- BS-EN-981 - Safety of machinery. System of auditory and visual danger and information signals
- BS-EN-982 - Safety of Machinery. Safety Requirements for Fluid Power Systems and Their Components.
- BS-EN-983 - Safety of Machinery, Safety Requirements for Fluid Power Systems & Their Components, P
- BS-EN-999 - Safety of Machinery. the Positioning of Protective Equipment in Respect of Approach Sp
- BS-EN-IEC-60749-18 - Semiconductor devices. Mechanical and climatic test methods
- BS-EN-IEC-60749-18-TC - Tracked Changes. Semiconductor devices. Mechanical and climatic test methods
- BS-EN-IEC-61010-2-201 - Safety requirements for electrical equipment for measurement, control and laboratory use. Particular requirements for control equipment
- BS-EN-IEC-61010-2-201-TC - Tracked Changes. Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61010-2-202 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-IEC-61496-1 - Safety of machinery. Electro-sensitive protective equipment
- BS-EN-IEC-61496-2 - Safety of machinery. Electro-sensitive protective equipment
- BS-EN-IEC-61496-3 - Safety of machinery. Electro-sensitive protective equipment. Particular requirements for active opto-electronic protective devices responsive to diffuse Reflection (AOPDDR)
- BS-EN-IEC-61800-5-1 - Adjustable speed electrical power drive systems
- BS-EN-IEC-61800-5-3 - Adjustable speed electrical power drive systems
- BS-EN-IEC-62046 - Safety of machinery. Application of protective equipment to detect the presence of persons
- BS-EN-IEC-62046-TC - Tracked Changes. Safety of machinery. Application of protective equipment to detect the presence of persons
- BS-EN-IEC-62061 - Safety of machinery. Functional safety of safety-related control systems
- BS-EN-IEC-62061-TC - Tracked Changes. Safety of machinery. Functional safety of safety-related control systems
- BS-EN-IEC-62841-4-6 - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery. Safety
- BS-EN-ISO-10218-1 - Robots and robotic devices. Safety requirements for industrial robots
- BS-EN-ISO-11161 - Safety of machinery. Integrated manufacturing systems. Basic requirements
- BS-EN-ISO-11553-1 - Safety of machinery. Laser processing machines
- BS-EN-ISO-11553-2 - Safety of machinery. Laser processing machines
- BS-EN-ISO-11553-3 - Safety of machinery. Laser processing machines
- BS-EN-ISO-12100-1 - Part 1: Basic Terminology, Methodology, Safety of Machinery- Basic Concepts, General Prin
- BS-EN-ISO-12100-2 - Part 2: Technical Principles, Safety of Machinery - Basic Concepts, General Principles For
- BS-EN-ISO-13732-1 - Ergonomics of the thermal environment. Methods for the assessment of human responses to contact with surfaces
- BS-EN-ISO-13849-1 - Safety of machinery. Safety-related parts of control systems
- BS-EN-ISO-13849-1-TC - Tracked Changes. Safety of machinery. Safety-related parts of control systems
- BS-EN-ISO-13849-2 - Safety of machinery. Safety-related parts of control systems
- BS-EN-ISO-13850 - Safety of machinery. Emergency stop function. Principles for design
- BS-EN-ISO-13854 - Safety of machinery. Minimum gaps to avoid crushing of parts of the human body
- BS-EN-ISO-13855 - Safety of machinery. Positioning of safeguards with respect to the approach speeds of parts of the human body
- BS-EN-ISO-13856-1 - Safety of machinery. Pressure-sensitive protective devices
- BS-EN-ISO-13856-2 - Safety of machinery. Pressure-sensitive protective devices
- BS-EN-ISO-13856-3 - Safety of machinery. Pressure-sensitive protective devices
- BS-EN-ISO-13857 - Safety of machinery. Safety distances to prevent hazard zones being reached by upper and lower limbs
- BS-EN-ISO-14118 - Safety of machinery. Prevention of unexpected start-up
- BS-EN-ISO-14119 - Safety of machinery. Interlocking devices associated with guards. Principles for design and selection
- BS-EN-ISO-14120 - Safety of machinery. Guards. General requirements for the design and construction of fixed and movable guards
- BS-EN-ISO-14121-1 - Safety of machinery. Risk assessment
- BS-EN-ISO-14122-1 - Safety of machinery. Permanent means of access to machinery
- BS-EN-ISO-14122-2 - Safety of machinery. Permanent means of access to machinery
- BS-EN-ISO-14122-3 - Safety of machinery. Permanent means of access to machinery
- BS-EN-ISO-14122-4 - Safety of machinery. Permanent means of access to machinery
- BS-EN-ISO-14123-1 - Safety of machinery. Reduction of risks to health resulting from hazardous substances emitted by machinery
- BS-EN-ISO-14123-2 - Safety of machinery. Reduction of risks to health resulting from hazardous substances emitted by machinery
- BS-EN-ISO-14159 - Safety of machinery. Hygiene requirements for the design of machinery
- BS-EN-ISO-14738 - Safety of machinery. Anthropometric requirements for the design of workstations at machinery
- BS-EN-ISO-15537 - Principles for selecting and using test persons for testing anthropometric aspects of industrial products and designs
- BS-EN-ISO-16090-1-TC - Tracked Changes. Machine tools safety. Machining centres, milling machines, transfer machines
- BS-EN-ISO-19085-1 - Woodworking machines. Safety
- BS-EN-ISO-19085-11 - Woodworking machines. Safety
- BS-EN-ISO-19085-12 - Woodworking machines. Safety
- BS-EN-ISO-19085-14 - Woodworking machines. Safety
- BS-EN-ISO-19085-14-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-15 - Woodworking machines. Safety
- BS-EN-ISO-19085-1-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-2 - Woodworking machines. Safety
- BS-EN-ISO-19085-2-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-3 - Woodworking machine. Safety
- BS-EN-ISO-19085-4 - Woodworking machines. Safety
- BS-EN-ISO-19085-4-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-5 - Woodworking machines. Safety
- BS-EN-ISO-19085-5-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-6 - Woodworking machines. Safety
- BS-EN-ISO-19085-6-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-7 - Woodworking machines. Safety
- BS-EN-ISO-19085-7-TC - Tracked Changes. Woodworking machines. Safety
- BS-EN-ISO-19085-8 - Woodworking machines. Safety
- BS-EN-ISO-19085-9 - Woodworking machines. Safety
- BS-EN-ISO-19353 - Safety of machinery. Fire prevention and fire protection
- BS-EN-ISO-20321 - Petroleum, petrochemical and natural gas industries. Safety of machineries. Powered elevators
- BS-EN-ISO-20607 - Safety of machinery. Instruction handbook. General drafting principles
- BS-EN-ISO-21469 - Safety of machinery. Lubricants with incidental product contact. Hygiene requirements
- BS-EN-ISO-23062-TC - Tracked Changes. Foundry machinery. Safety requirements for molding and coremaking machinery and associated equipment
- BS-EN-ISO-4413 - Hydraulic fluid power. General rules and safety requirements for systems and their components
- BS-EN-ISO-4414 - Pneumatic fluid power. General rules and safety requirements for systems and their components
- BS-IEC-60204-33 - Safety of machinery. Electrical equipment of machines. Requirements for semiconductor fabrication equipment
- BS-IEC-61496-2 - Part 2: Particular Requirements for Equipment Using Active OPTO-Electronic Devices
- BS-IEC-61511-2 - Functional Safety, Safety Instrumented Systems for the Process Industry Sector, Guidel
- BS-ISO-13105-1 - Building construction machinery and equipment. Machinery for concrete surface floating and finishing
- BS-ISO-13105-1-TC - Tracked Changes. Building construction machinery and equipment. Machinery for concrete surface floating and finishing
- BS-ISO-13105-2 - Building construction machinery and equipment. Machinery for concrete surface floating and finishing
- BS-ISO-13105-2-TC - Tracked Changes. Building construction machinery and equipment. Machinery for concrete surface floating and finishing
- BS-ISO-23314-2 - Ships and marine technology. Ballast water management systems (BWMS)
- DD-CEN-61496-3 - Safety of Machinery, Electro-Sensitive Protective Equipment, Particular Requirements F
- DD-CLC-50418 - Safety of machinery. Electro-sensitive protective equipment. Passive infra-red protective devices (PIPDs)
- DD-CLC-61496-2 - Safety of machinery. Electro-sensitive protective equipment
- DD-CLC-61496-3 - Safety of machinery. Electro-sensitive protective equipment
- DD-CLC-62046 - Safety of machinery. Application of protective equipment to detect the presence of persons
- DD-IEC/PAS61784-3-18 - Industrial communication networks. Profiles
- KIT-8 - Safety of Machinery Pack
- PAS-1892 - Connected and automated plant (CAP). Defining and specifying the use of CAP in construction and maintenance works for the purposes of procurement and deployment. Specification
- PD-5304 - Guidance on safe use of machinery
- PD-5304-TC - Tracked Changes. Guidance on safe use of machinery
- PD-CEN-16710-1 - Ergonomics methods
- PD-CEN-ISO-22100-1 - Safety of machinery. Relationship with ISO 12100
- PD-CEN-ISO-22100-4 - Safety of machinery. Relationship with ISO 12100. Guidance to machinery manufacturers for consideration of related IT-security (cyber security) aspects.
- PD-CEN-ISO-22100-5 - Safety of machinery. Relationship with ISO 12100
- PD-CLC-IEC-61511-0 - Functional safety. Safety instrumented systems for the process industry sector. Functional safety for the process industry and IEC 61511.
- PD-CLC-IEC-61511-4 - Functional safety. Safety instrumented systems for the process industry sector
- PD-CLC-IEC-63069 - Industrial-process measurement, control and automation. Framework for functional safety and security
- PD-CR-954-100 - Safety of machinery. Safety-related parts of control systems
- PD-IEC-61496-4 - Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61496-4-2 - Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61496-4-2-TC - Tracked Changes. Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61496-4-3 - Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61496-4-3-TC - Tracked Changes. Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61496-5 - Safety of machinery. Electro-sensitive protective equipment
- PD-IEC-61511-0 - Functional safety. Safety instrumented systems for the process industry sector
- PD-IEC-61511-4 - Functional safety. Safety instrumented systems for the process industry sector
- PD-IEC-62513 - Safety of machinery. Guidelines for the use of communication systems in safety-related applications
- PD-IEC-62998-2 - Safety of machinery
- PD-IEC-62998-3 - Safety of machinery. Safety-related sensors used for the protection of persons
- PD-IEC-63069 - Industrial-process measurement, control and automation. Framework for functional safety and security
- PD-IEC-63074 - Safety of machinery. Security aspects related to functional safety of safety-related control systems
- PD-IEC-63074-TC - Tracked Changes. Safety of machinery. Security aspects related to functional safety of safety-related control systems
- PD-IEC-63161 - Assignment of safety integrity requirements. Basic rationale
- PD-IEC-63176 - Process analysis technology systems as part of safety instrumented systems
- PD-IEC-63394 - Safety of machinery. Guidelines on functional safety of safety-related control system
- PD-ISO-18569 - Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
- PD-ISO-19837 - Safety of machinery. Trapped key interlocking devices. Principles for design and selection
- PD-ISO-22053 - Safety of machinery. Safeguarding supportive system
- PD-ISO-22100-1 - Safety of machinery. Relationship with ISO 12100. How ISO 12100 relates to type-B and type-C standards
- PD-ISO-22100-2 - Safety of machinery. Relationship with ISO 12100
- PD-ISO-22100-3 - Safety of machinery. Relationship with ISO 12100
- PD-ISO-22100-4 - Safety of machinery. Relationship with ISO 12100
- PD-ISO-22100-5 - Safety of machinery. Relationship with ISO 12100
- PD-ISO-24119 - Safety of machinery. Evaluation of fault masking serial connection of interlocking devices associated with guards with potential free contacts
- PD-ISO-GUIDE-78 - Safety of machinery. Rules for drafting and presentation of safety standards
- PD-R044-001 - Safety of machinery. Guidance and recommendations for the avoidance of hazards due to static electricity
- PP-7722 - Designing safe machinery. Guidance for higher education to the standards and regulations
- PP-7722-SET - Designing Safe Machinery, Guidance for Higher Education To the Standards & Regulations
IEC:
- IEC-60204-1 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements
- IEC-60204-11 - Safety of machinery - Electrical equipment of machines - Part 11: Requirements for equipment for voltages above 1 000 V AC or 1 500 V DC and not exceeding 36 kV
- IEC-60204-11-RL - Safety of machinery - Electrical equipment of machines - Part 11: Requirements for equipment for voltages above 1 000 V AC or 1 500 V DC and not exceeding 36 kV
- IEC-60204-1-RL - Safety of machinery - Electrical equipment of machines - Part 1: General requirements
- IEC-60204-31 - Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems
- IEC-60204-33 - Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
- IEC-60204-34 - Safety of machinery - Electrical equipment of machines - Part 34: Requirements for machine tools
- IEC-60204-SERIES - Safety of machinery - Electrical equipment of machines - ALL PARTS
- IEC-60445 - Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
- IEC-60445-RL - Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
- IEC-60825-1 - Safety of laser products - Part 1: Equipment classification and requirements
- IEC-60825 SERIES - Safety of laser products - ALL PARTS
- IEC-61010-2-201 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-201: Particular requirements for control equipment
- IEC-61010-2-202 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators
- IEC-61010-2-202-RL - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators
- IEC-61285 - Industrial-process control - Safety of analyser houses
- IEC-61310-1 - Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
- IEC-61310-2 - Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
- IEC-61310-3 - Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
- IEC-61496-1 - Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
- IEC-61496-1-1 - Amendment 1: Safety of Machinery - Electro-Sensitive Protective Equipment - Part 1: Ge
- IEC-61496-2 - Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
- IEC-61496-3 - Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for active opto-electronic protective devices responsive to diffuse Reflection (AOPDDR)
- IEC-61496-3-RL - Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for active opto-electronic protective devices responsive to diffuse Reflection (AOPDDR)
- IEC-61496-4 - Safety of machinery - Electro-sensitive protective equipment - Part 4: Particular requirements for equipment using vision based protective devices (VBPD)
- IEC-61496-4-2 - Safety of machinery - Electro-sensitive protective equipment - Part 4-2: Particular requirements for equipment using vision based protective devices (VBPD) - Additional requirements when using reference pattern techniques (VBPDPP)
- IEC-61496-4-2-RL - Safety of machinery - Electro-sensitive protective equipment - Part 4-2: Particular requirements for equipment using vision based protective devices (VBPD) - Additional requirements when using reference pattern techniques (VBPDPP)
- IEC-61496-4-3 - Safety of machinery - Electro-sensitive protective equipment - Part 4-3: Particular requirements for equipment using vision based protective devices (VBPD) - Additional requirements when using stereo vision techniques (VBPDST)
- IEC-61496-4-3-RL - Safety of machinery - Electro-sensitive protective equipment - Part 4-3: Particular requirements for equipment using vision based protective devices (VBPD) - Additional requirements when using stereo vision techniques (VBPDST)
- IEC-61496-5 - Safety of machinery . Electro-sensitive protective equipment - Part 5: Particular requirements for radar-based protective devices
- IEC-61508-0 - Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 0: Functional safety and IEC 61508
- IEC-61508-1 - Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements
- IEC-61511-0 - Functional safety - Safety instrumented systems for the process industry sector - Part 0: Functional safety for the process industry and IEC 61511
- IEC-61511-1 - Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements
- IEC-61511-1-AM1 - Amendment 1 - Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements
- IEC-61511-1-RL - Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements
- IEC-61511-2 - Functional safety - Safety instrumented systems for the process industry sector - Part 2: Guidelines for the application of IEC 61511-1:2016
- IEC-61511-2-RL - Functional safety - Safety instrumented systems for the process industry sector - Part 2: Guidelines for the application of IEC 61511-1:2016
- IEC-61511-3 - Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels
- IEC-61511-3-RL - Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels
- IEC-61511-4 - Functional safety - Safety instrumented systems for the process industry sector - Part 4: Explanation and rationale for changes in IEC 61511-1 from Edition 1 to Edition 2
- IEC-61511-SERIES - Functional safety - Safety instrumented systems for the process industry sector - ALL PARTS
- IEC-61511-SERIES-RL - Functional safety - Safety instrumented systems for the process industry sector - ALL PARTS
- IEC-61784-3-18 - Industrial communication networks - Profiles - Part 3-18: Functional safety fieldbuses - Additional specifications for CPF 18
- IEC-61784-3-18-AM1 - Amendment 1 - Industrial communication networks - Profiles - Part 3-18: Functional safety fieldbuses - Additional specifications for CPF 18
- IEC-61800-5-2 - Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
- IEC-61800-5-2-RL - Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
- IEC-61800-5-3 - Adjustable speed electrical power drive systems - Part 5-3: Safety requirements - Functional, electrical and environmental requirements for encoders
- IEC-62046 - Safety of machinery - Application of protective equipment to detect the presence of persons
- IEC-62061 - Safety of machinery - Functional safety of safety-related control systems
- IEC-62061-1 - Guidance on the application of ISO 13849-1 and IEC 62061 in the design of safety-related control systems for machinery
- IEC-62061-AM1 - Amendment 1 - Safety of machinery - Functional safety of safety-related control systems
- IEC-62061-AM2 - Amendment 2, Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
- IEC-62513 - Safety of machinery - Guidelines for the use of communication systems in safety-related applications
- IEC-62745 - Safety of machinery - Requirements for cableless control systems of machinery
- IEC-62998-1 - Safety of machinery - Safety-related sensors used for the protection of persons
- IEC-62998-2 - Safety of machinery - Part 2: Examples of application
- IEC-62998-3 - Safety of machinery - Safety-related sensors used for the protection of persons - Part 3: Sensor technologies and algorithms
- IEC-63069 - Industrial-process measurement, control and automation - Framework for functional safety and security
- IEC-63074 - Safety of machinery - Security aspects related to functional safety of safety-related control systems
- IEC-63176 - Process analysis technology systems as part of safety instrumented systems
- IEC/PAS-61784-3-18 - Part 3-18: Functional Safety Fieldbuses - Additional Specifications for Cpf Snpfamily,
ISO:
- ISO-11161 - Safety of machinery - Integrated manufacturing systems - Basic requirements
- ISO-11161/AM1 - Industrial automation systems - Safety of integrated manufacturing systems - Basic requirements - Amendment 1
- ISO-11553-1 - Safety of machinery - Laser processing machines - Part 1: Laser safety requirements
- ISO-11553-2 - Safety of machinery - Laser processing machines - Part 2: Safety requirements for hand-held laser processing devices
- ISO-11553-3 - Safety of machinery - Laser processing machines - Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2)
- ISO-12100 - Safety of machinery - General principles for design - Risk assessment and risk reduction
- ISO-12100-1 - Safety of machinery -- Basic concepts, general principles for design -- Part 1: Basic terminology, methodology
- ISO-12100-1-1 - Amendment 1: Safety of machinery -- Basic concepts, general principles for design -- Part 1: Basic terminology, methodology
- ISO-12100-2 - Safety of machinery -- Basic concepts, general principles for design -- Part 2: Technical principles and specifications
- ISO-12100-2-1 - Amendment 1: Safety of machinery -- Basic concepts, general principles for design -- Part 2: Technical principles and specifications
- ISO-13105-2 - Building construction machinery and equipment - Machinery for concrete surface floating and finishing - Part 2: Safety requirements and verification
- ISO-13105-2-AM1 - - Amendment 1
- ISO-13849-1 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design
- ISO-13849-2 - Safety of machinery - Safety-related parts of control systems - Part 2: Validation
- ISO-13850 - Safety of machinery - Emergency stop function - Principles for design
- ISO-13851 - Safety of machinery - Two-hand control devices - Principles for design and selection
- ISO-13852 - Safety of machinery - Safety distances to prevent danger zones being reached by the upper limbs
- ISO-13854 - Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
- ISO-13855 - Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts of the human body
- ISO-13856-1 - Safety of machinery - Pressure-sensitive protective devices - Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors
- ISO-13856-2 - Safety of machinery - Pressure-sensitive protective devices - Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars
- ISO-13856-3 - Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices
- ISO-13857 - Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs
- ISO-14118 - Safety of machinery - Prevention of unexpected start-up
- ISO-14119 - Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
- ISO-14119-1 - Safety of machinery - Interlocking devices associated with guards - Principles for design and selectionAmendment 1: Design to minimize defeat possibilities
- ISO-14120 - Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
- ISO-14121-1 - Safety of machinery -- Risk assessment -- Part 1: Principles
- ISO-14121-2 - Safety of machinery - Risk assessment - Part 2: Practical guidance and examples of methods
- ISO-14122-1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access
- ISO-14122-1-AM1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means of access between two levels - Amendment 1
- ISO-14122-2 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways
- ISO-14122-2-AM1 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways - Amendment 1
- ISO-14122-3 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails
- ISO-14122-3-AM1 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails - Amendment 1
- ISO-14122-4 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders
- ISO-14122-4-AM1 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders - Amendment 1
- ISO-14123-1 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers
- ISO-14123-2 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
- ISO-14159 - Safety of machinery - Hygiene requirements for the design of machinery
- ISO-14738 - Safety of machinery -- Anthropometric requirements for the design of workstations at machinery
- ISO-15534-1 - Ergonomic design for the safety of machinery - Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery
- ISO-15534-2 - Ergonomic design for the safety of machinery - Part 2: Principles for determining the dimensions required for access openings
- ISO-15534-3 - Ergonomic design for the safety of machinery - Part 3: Anthropometric data
- ISO-15537 - Principles for selecting and using test persons for testing anthropometric aspects of industrial products and designs
- ISO-18569 - Safety of machinery - Guidelines for the understanding and use of safety of machinery standards
- ISO-19085-1 - Woodworking machines - Safety - Part 1: Common requirements
- ISO-19085-10 - Woodworking machines - Safety - Part 10: Building site saws (contractor saws)
- ISO-19085-11 - Woodworking machines - Safety - Part 11: Combined machines
- ISO-19085-12 - Woodworking machines - Safety - Part 12: Tenoning/profiling machines
- ISO-19085-13 - Woodworking machines - Safety - Part 13: Multi-blade rip sawing machines with manual loading and/or unloading
- ISO-19085-14 - Woodworking machines - Safety - Part 14: Four-sided moulding machines
- ISO-19085-15 - Woodworking machines - Safety - Part 15: Presses
- ISO-19085-2 - Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines
- ISO-19085-3 - Woodworking machines - Safety - Part 3: Numerically controlled (NC/CNC) boring and routing machines
- ISO-19085-4 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines
- ISO-19085-5 - Woodworking machines - Safety - Part 5: Dimension saws
- ISO-19085-6 - Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines (toupie)
- ISO-19085-7 - Woodworking machines - Safety - Part 7: Surface planing, thickness planing, combined surface/thickness planing machines
- ISO-19085-8 - Woodworking machines - Safety - Part 8: Wide belt sanding machines and surface treating machines
- ISO-19085-9 - Woodworking machines - Safety - Part 9: Circular saw benches (with and without sliding table)
- ISO-19296 - Mining - Mobile machines working underground - Machine safety
- ISO-19353 - Safety of machinery - Fire prevention and fire protection
- ISO-19837 - Safety of machinery - Trapped key interlocking devices - Principles for design and selection
- ISO-20321 - Petroleum, petrochemical and natural gas industries - Safety of machineries - Powered elevators
- ISO-20607 - Safety of machinery - Instruction handbook - General drafting principles
- ISO-21469 - Safety of machinery - Lubricants with incidental product contact - Hygiene requirements
- ISO-22053 - Safety of machinery - Safeguarding supportive system
- ISO-22100-1 - Safety of machinery - Relationship with ISO 12100 - Part 1: How ISO 12100 relates to type-B and type-C standards
- ISO-22100-2 - Safety of machinery - Relationship with ISO 12100 - Part 2: How ISO 12100 relates to ISO 13849-1
- ISO-22100-3 - Safety of machinery - Relationship with ISO 12100 - Part 3: Implementation of ergonomic principles in safety standards
- ISO-22100-4 - Safety of machinery - Relationship with ISO 12100 - Part 4: Guidance to machinery manufacturers for consideration of related IT-security (cyber security) aspects
- ISO-22100-5 - Safety of machinery - Relationship with ISO 12100 - Part 5: Implications of artificial intelligence machine learning
- ISO-23062 - Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment
- ISO-23314-2 - Ships and marine technology - Ballast water management systems (BWMS) - Part 2: Risk assessment and risk reduction of BWMS using electrolytic methods
- ISO-23849 - Guidance on the application of ISO 13849-1 and IEC 62061 in the design of safety-related control systems for machinery
- ISO-24119 - Safety of machinery - Evaluation of fault masking serial connection of interlocking devices associated with guards with potential free contacts
- ISO-29042-1 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods
- ISO-29042-2 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant
- ISO-29042-3 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant
- ISO-29042-4 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4: Tracer method for the measurement of the capture efficiency of an exhaust system
- ISO-29042-5 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 5: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with unducted outlet
- ISO-29042-6 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with ducted outlet
- ISO-29042-7 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Test bench method for the measurement of the pollutant concentration parameter
- ISO-29042-8 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8: Room method for the measurement of the pollutant concentration parameter
- ISO-29042-9 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Decontamination index
- ISO-GUIDE-78 - Safety of machinery - Rules for drafting and presentation of safety standards
Other SDOs:
- DIN-EN-1005-3 - Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation; German version EN 1005-3:2002+A1:2008
- DIN-EN-1005-4 - Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery; German version EN 1005-4:2005+A1:2008
- DIN-EN-1005-5 - Safety of machinery - Human physical performance - Part 5: Risk assessment for repetitive handling at high frequency; German version EN 1005-5:2007
- DIN-EN-1127-2 - Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining; German version EN 1127-2:2014
- DIN-EN-12198-2 - Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 2: Radiation emission measurement procedure; German version EN 12198-2:2002+A1:2008
- DIN-EN-12198-3 - Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening; German version EN 12198-3:2002+A1:2008
- DIN-EN-13478 - Safety of Machinery - Fire Prevention & Protection
- DIN-EN-13861 - Safety of machinery - Guidance for the application of ergonomics standards in the design of machinery
- DIN-EN-1760-3 - Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices; German version EN 1760-3:2004+A1:2009
- DIN-EN-614-1 - Part 1: Terminology & General Principles, Safety of Machinery - Ergonomic Design Princ
- DIN-EN-ISO-12100-1 - Part 1: Basic Terminology, Methodology, Safety of Machinery, Basic Concepts, General P
- DIN-EN-ISO-12100-2 - Part 2: Technical Principles, Safety of Machinery, Basic Concepts, General Principles
- DIN-EN-ISO-13849-1 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design
- DIN-EN-ISO-13849-2 - Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
- DIN-EN-ISO-13850 - Safety of machinery - Emergency stop function - Principles for design
- DIN-EN-ISO-14122-1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access
- DIN-EN-ISO-14122-2 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways
- DIN-EN-ISO-14122-3 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails
- DIN-EN-ISO-14122-4 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders
- DIN-EN-ISO-14159 - Safety of Machinery, Hygiene Requirements for the Design of Machinery
- DIN-EN-ISO-14738 - Safety of Machinery - Anthropometric Requirements for the Design of Workstations at Ma
- DS-ISO-14121-2 - Safety of machinery - Risk assessment - Part 2: Practical guidance and examples of methods
- EN-1005-1 - Part 1: Terms & Definitions, Human Physical Performance, Safety of Machinery
- EN-1005-2 - Part 2: Manual Handling of Machinery & Component Parts of Machinery, Safety of Machine
- EN-1005-3 - Part 3: Recommended Force Limits for Machinery Operation, Safety of Machinery - Human
- EN-1005-4 - Part 4: Evaluation of Working Postures & Movements in Relation To Machinery, Safety Of
- EN-1005-5 - Part 5: Risk Assessment for Repetitive Handling at High Frequency, Safety of Machinery
- EN-1034-1 - Part 1: Common Requirements, Safety of Machinery - Safety Requirements for the Design
- EN-1037 - Safety of Machinery - Prevention of Unexpected Start-Up
- EN-1088 - Safety of machinery. Interlocking devices associated with guards. Principles for design and selection (Replaced by EN-ISO-14119)
- EN-1093-4 - Part 4: Capture Efficiency of an Exhaust System - Tracer Method, Safety of Machinery -
- EN-1127-2 - Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining
- EN-12198-2 - Part 2: Radiation Emission Measurement Procedure, Safety of Machinery - Assessment &
- EN-12198-3 - Part 3: Reduction of Radiation by Attenuation or Screening, Safety of Machinery - Ass
- EN-12786 - Safety of machinery - Requirements for the drafting of the vibration clauses of safety standards
- EN-13861 - Safety of machinery - Guidance for the application of ergonomics standards in the design of machinery
- EN-16710-2 - Ergonomics methods - Part 2: A methodology for work analysis to support design
- EN-1760-1 - Part 1: General Principles for the Design & Testing of Pressure-Sensitive Mats & Press
- EN-1760-3 - Part 3: General Principles for the Design & Testing of Pressure Sensitive Bumpers, Pla
- EN-1837 - Safety of Machinery - Integral Lighting of Machines
- EN-547-1 - Part 1: Principles for Determining the Dimensions Required for Openings for Whole Body
- EN-547-2 - Part 2: Principles for Determining the Dimensions Required for Access Openings, Safety Of
- EN-547-3 - Part 3: Anthropometric Data, Safety of Machinery - Human Body Measurements
- EN-574 - Safety of Machinery - Two-Hand Control Devices - Functional Aspects - Principles For
- EN-60204-1 - Safety of Machinery, Electrical Equipment of Machines, General Requirements
- EN-60204-11 - Part 11: Requirements for Hv Equipment for Voltages Above 1000 V a.C. or 1500 V D.C. &
- EN-60204-31 - Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems
- EN-60204-33 - Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
- EN-60825-1 - Safety of laser products - Part 1: Equipment classification and requirements
- EN-61010-2-201 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-201: Particular requirements for control equipment
- EN-61010-2-202 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators
- EN-61285 - Industrial-process control - Safety of analyzer houses
- EN-61310-1 - Safety of Machinery, Indication, Marking & Actuation, Requirements for Visual, Acousti
- EN-61310-2 - Safety of Machinery, Indication, Marking & Actuation, Requirements for Marking
- EN-61310-3 - Safety of Machinery, Indication, Marking & Actuation, Requirements for the Location &
- EN-614-1 - Safety of machinery. Ergonomic design principles. Terminology and general principles
- EN-614-2 - Part 2: Interactions Between the Design of Machinery & Work Tasks, Safety of Machiner
- EN-61496-1 - Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
- EN-61496-2 - Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
- EN-61511-1 - Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming Requirements
- EN-61511-2 - Functional safety - Safety instrumented systems for the process industry sector - Part 2: Guidelines for the application of IEC 61511-1
- EN-61784-3-18 - Industrial communication networks - Profiles - Part 3-18: Functional safety fieldbuses - Additional specifications for CPF 18
- EN-61800-5-2 - Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
- EN-62061 - Safety of machinery - Functional safety of safety-related electrical, Electronic and programmable electronic control systems
- EN-626-1 - Safety of machinery. Reduction of risks to health from Hazardous substances emitted by machinery. Principles and specifications for machinery manufacturers
- EN-626-2 - Safety of machinery. Reduction of risk to health from hazardous substances emitted by machinery. Methodology leading to verification procedures
- EN-62745 - Safety of machinery - Requirements for cableless control systems of machinery
- EN-842 - Safety of Machinery - Visual Danger Signals - General Requirements, Design & Testing
- EN-894-1 - Part 1: General Principles for Human Interactions With Displays & Control Actuators, S
- EN-894-2 - Part 2: Displays, Safety of Machinery, Ergonomics Requiremennts for the Design of Displays
- EN-894-4 - Part 4: Location & Arrangement of Displays & Control Actuators, Safety of Machinery -
- EN-953 - Safety of Machinery - Guards - General Requirements for the Design & Construction Of
- EN-981 - Safety of Machinery - System of Auditory & Visual Danger & Information Signals
- EN-IEC-60204-11 - Safety of machinery - Electrical equipment of machines - Part 11: Requirements for equipment for voltages above 1000 V AC or 1500 V DC and not exceeding 36 kV (IEC 60204-11:2018)
- EN-IEC-61496-3 - Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for active opto-electronic protective devices responsive to diffuse Reflection (AOPDDR) (IEC 61496-3:2018)
- EN-IEC-62046 - Safety of machinery - Application of protective equipment to detect the presence of persons
- EN-ISO-11161 - Safety of Machinery - Integrated Manufacturing Systems - Basic Requirements
- EN-ISO-11553-1 - Part 1: General Safety Requirements, Safety of Machinery - Laser Processing Machines
- EN-ISO-11553-2 - Part 2: Safety Requirements for Hand-Held Laser Processing Devices, Safety of Machiner
- EN-ISO-11553-3 - Safety of machinery - Laser processing machines - Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) (ISO 11553-3:2013)
- EN-ISO-12100-1 - Part 1: Basic Terminology, Methodology, Safety of Machinery,Basic Concepts, General Pr
- EN-ISO-13732-1 - Ergonomics of the Thermal Environment, Methods for the Assessment of Human Responses T
- EN-ISO-13849-1 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design
- EN-ISO-13849-2 - Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
- EN-ISO-13850 - Safety of machinery - Emergency stop function - Principles for design
- EN-ISO-13851 - Safety of machinery - Two-hand control devices - Principles for design and selection (ISO 13851:2019)
- EN-ISO-13855 - Safety of Machinery - Positioning of Safeguards With Respect To the Approach Speeds Of
- EN-ISO-13856-1 - Safety of machinery - Pressure-sensitive protective devices - Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors (ISO 13856-1:2013)
- EN-ISO-13856-2 - Safety of machinery - Pressure-sensitive protective devices - Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars (ISO 13856-2:2013)
- EN-ISO-13856-3 - Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices (ISO 13856-3:2013)
- EN-ISO-13857 - Safety of Machinery, Safety Distances To Prevent Hazard Zones Being Reached by Upper &
- EN-ISO-14118 - Safety of machinery - Prevention of unexpected start-up
- EN-ISO-14120 - Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
- EN-ISO-14122-1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access
- EN-ISO-14122-2 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways
- EN-ISO-14122-3 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails
- EN-ISO-14122-4 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders
- EN-ISO-14123-1 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers
- EN-ISO-14123-2 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
- EN-ISO-14159 - Safety of Machinery, Hygiene Requirements for the Design of Machinery
- EN-ISO-14738 - Safety of Machinery - Anthropometric Requirements for the Design of Workstations at Ma
- EN-ISO-15537 - Principles for Selecting & Using Test Persons for Testing Anthropometric Aspects of In
- EN-ISO-19085-1 - Woodworking machines - Safety - Part 1: Common requirements
- EN-ISO-19085-10 - Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO 19085-10:2018)
- EN-ISO-19085-2 - Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines
- EN-ISO-19085-3 - Woodworking machines. Safety requirements. Numerically controlled (NC) boring and routing machines
- EN-ISO-19085-4 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2018)
- EN-ISO-19085-5 - Woodworking machines - Safety - Part 5: Dimension saws
- EN-ISO-19085-7 - Woodworking machines - Safety - Part 7: Surface planing, thickness planing, combined surface/thickness planing machines (ISO 19085-7:2019)
- EN-ISO-19353 - Safety of machinery - Fire prevention and fire protection
- EN-ISO-20607 - Safety of machinery - Instruction handbook - General drafting principles (ISO 20607:2019)
- EN-ISO-21469 - Safety of Machinery - Lubricants With Incidental Product Contact - Hygiene Requirement
- JIS-B-9700-1 - Part 1: Basic Terminology, Methodology, Safety of Machinery - Basic Concepts, General
- JIS-B-9700-2 - Part 2: Technical Principles, Safety of Machinery - Basic Concepts, General Principles
- JIS-B-9702 - Safety of Machinery - Principles of Risk Assessment
- JIS-B-9703 - Safety of machinery -- Emergency stop -- Principles for design
- JIS-B-9704-1 - Safety of machinery -- Electro-sensitive protective equipment -- Part 1: General requirements and tests
- JIS-B-9704-3 - Safety of machinery -- Electro-sensitive protective equipment -- Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
- JIS-B-9705-1 - Safety of machinery -- Safety-related parts of control systems -- Part 1: General principles for design
- JIS-B-9706-1 - Safety of machinery -- Indication, marking and actuation -- Part 1: Requirements for visual, acoustic and tactile signals
- JIS-B-9706-2 - Safety of machinery -- Indication, marking and actuation -- Part 2: Requirements for marking
- JIS-B-9706-3 - Safety of machinery -- Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators
- JIS-B-9707 - Safety of Machinery - Safety Distances To Prevent Danger Zones Being Reached by the Up
- JIS-B-9708 - Safety of Machinery - Safety Distances To Prevent Danger Zones Being Reached by the Lo
- JIS-B-9709-1 - Safety of machinery -- Reduction of risks to health from hazardous substances emitted by machinery -- Part 1: Principles and specifications for machinery manufacturers
- JIS-B-9709-2 - Safety of machinery -- Reduction of risks to health from hazardous substances emitted by machinery -- Part 2: Methodology leading to verification procedures
- JIS-B-9711 - Safety of machinery -- Minimum gaps to avoid crushing of parts of the human body
- JIS-B-9713-1 - Safety of machinery -- Permanent means of access to machinery -- Part 1: Choice of a fixed means of access between two levels
- JIS-B-9713-2 - Safety of machinery -- Permanent means of access to machinery -- Part 2: Working platforms and walkways
- JIS-B-9713-3 - Safety of machinery -- Permanent means of access to machinery -- Part 3: Stairs, stepladders and guard-rails
- JIS-B-9713-4 - Safety of machinery -- Permanent means of access to machinery -- Part 4: Fixed ladders
- JIS-B-9717-1 - Safety of machinery -- Pressure-sensitive protective devices -- Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors
- JIS-B-9960-11 - Safety of machinery -- Electrical equipment of machines -- Part 11: Requirements for HV equipment for voltages above 1000V a.c. or 1500V d.c. and not exceeding 36kV
- JIS-B-9960-1-AM1 - Safety of machinery -- Electrical equipment of machines -- Part 1: General requirements (Amendment 1)
- JIS-B-9960-31 - Safety of machinery -- Electrical equipment of machines -- Part 31: Particular safety and EMC requirements for sewing machines, units and systems
- SIS-CEN-ISO/TR-22100-1 - Safety of machinery - Relationship with ISO 12100 - Part 1: How ISO 12100 relates to type-B and type-C standards (ISO/TR 22100-1:2021)
- SIS-CEN-ISO/TR-22100-5 - Safety of machinery - Relationship with ISO 12100 - Part 5: Implications of artificial intelligence machine learning (ISO/TR 22100-5:2021)
- SIS-CEN/TR-16710-1 - Ergonomics methods - Part 1: Feedback method - A method to understand how end users perform their work with machines
- SIS-CEN/TR-614-3 - Safety of machinery - Part 3: Ergonomic principles for the design of mobile machinery
- SIS-ISO-GUIDE-78 - ISO Guide 78 - Safety of machinery - Rules for the drafting and presentation of safety standards
- SIS-ISO/TR-14121-2 - Safety of machinery - Risk assessment - Part 2: Practical guidance and examples of methods (ISO 14121-2:2012, IDT)
- SIS-ISO/TR-22100-1 - Safety of machinery - Relationship with ISO 12100 - Part 1: How ISO 12100 relates to type-B and type-C standards (ISO/TR 22100-1:2015, IDT)
- SIS-ISO/TR-22100-2 - Safety of machinery - Relationship with ISO 12100 - Part 2: How ISO 12100 relates to ISO 13849-1 (ISO/TR 22100-2:2013, IDT)
- SIS-ISO/TR-22100-3 - Safety of machinery - Relationship with ISO 12100 - Part 3: Implementation of ergonomic principles in safety standards
- SIS-ISO/TR-23849 - Guidance on the application of ISO 13849-1 and IEC 62061 in the design of safety-related control systems for machinery
- SIS-ISO/TR-24119 - Safety of machinery Evaluation of fault masking serial connection of interlocking devices associated with guards with potential free contacts
- SIS-ISO/TS-19837 - Safety of machinery - Trapped key interlocking devices - Principles for design and selection and configuration
- SS-EN-1005-1 - Safety of machinery - Human physical performance - Part 1: Terms and definitions
- SS-EN-1005-2 - Safety of machinery - Human physical performance - Part 2: Manuel handling of machinery and component parts of machinery
- SS-EN-1005-3 - Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
- SS-EN-1005-4 - Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery
- SS-EN-1005-5 - Safety of machinery - Human physical performance - Part 5: Risk assessment for repetitive handling at high frequency
- SS-EN-1037 - Safety of machinery - Prevention of unexpected start-up
- SS-EN-1050 - Safety of machinery - Principles for risk assessment
- SS-EN-1070 - Safety of machinery - Terminology
- SS-EN-1088 - Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
- SS-EN-1088-AM1 - Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
- SS-EN-1093-1 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods
- SS-EN-1093-11 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index
- SS-EN-1093-2 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant
- SS-EN-1093-3 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant
- SS-EN-1093-4 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4: Capture efficiency of an exhaust system - Tracer method
- SS-EN-1093-6 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Separation efficiency by mass, unducted outlet
- SS-EN-1093-7 - Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet
- SS-EN-1093-8 - Safety of machinery - Evaluation of the emission of airborne hazardous substances from machines - Part 8: Pollutant concentration parameter, test bench method
- SS-EN-1093-9 - Safety of machinery - Evaluation of the emission of airborne hazardous substances from machines - Part 9: Pollutant concentration parameter, room method
- SS-EN-1114-1 - Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders
- SS-EN-1127-1 - Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
- SS-EN-12198-1 - Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles
- SS-EN-12198-2 - Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 2: Radiation emission measurement procedure
- SS-EN-12198-3 - Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening
- SS-EN-12786 - Safety of machinery - Rules for the drafting of the vibration clauses of safety standards
- SS-EN-12817 - LPG Equipment and accessories - Inspection and requalification of LPG pressure vessels up to and including 13 m³
- SS-EN-13478 - Safety of machinery - Fire prevention and protection
- SS-EN-13861 - Safety of machinery - Guidance for the application of ergonomics standards in the design of machinery
- SS-EN-16710-2 - Ergonomics methods - Part 2: A methodology for work analysis to support design
- SS-EN-1746 - Safety of machinery - Guidance for the drafting of the noise clauses of safety standards
- SS-EN-1760-1 - Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
- SS-EN-1760-2 - Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
- SS-EN-1760-3 - Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices
- SS-EN-1837 - Safety of machinery - Integral lighting of machines
- SS-EN-292-1 - Safety of machinery - Basic concepts, general principles for design - Part 1: Basic terminology, methodology
- SS-EN-292-2 - Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles and specifications
- SS-EN-292-2-AM1 - Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles and specifications. Amendment 1
- SS-EN-294 - Safety of machinery - Safety distances to preventdanger zones being reached by the upper limbs
- SS-EN-349 - Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
- SS-EN-414 - Safety of machinery - Rules for the drafting and presentation of safety standards
- SS-EN-418 - Safety of machinery - Emergency stop equipment, functional aspects - Principles for design
- SS-EN-457 - Safety of machinery - Auditory danger signals - General requirements, design and testing (ISO 7731:1986 modified)
- SS-EN-547-1 - Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery
- SS-EN-547-2 - Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings
- SS-EN-547-3 - Safety of machinery - Human body measurements - Part 3: Anthropometric data
- SS-EN-563 - Safety of machinery - Tempertures of touchable surfaces - Ergonomics data to establish temperature limit values for hot surfaces
- SS-EN-563-AM1 - Safety of machinery - Temperatures of touchable surfaces - Ergonomics data to establish temperature limit values for hot surfaces
- SS-EN-574 - Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
- SS-EN-60204-11 - Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 5 000 V d.c. and not exceeding 36 kV
- SS-EN-60825-1 - Safety of laser products - Part 1: Equipment classification and requirements
- SS-EN-614-1 - Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
- SS-EN-614-2 - Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks
- SS-EN-61508-1 - Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements
- SS-EN-62061 - Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
- SS-EN-626-1 - Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers
- SS-EN-626-2 - Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
- SS-EN-811 - Safety of machinery - Safety distances to preventanger zones being reached by the lower limbs
- SS-EN-842 - Safety of machinery - Visual danger signals - General requirements, design and testing
- SS-EN-894-1 - Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators
- SS-EN-894-2 - Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
- SS-EN-894-3 - Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
- SS-EN-894-4 - Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators
- SS-EN-953 - Safety of machinery - General requirements for the design and construction of fixed and movable guards
- SS-EN-954-1 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design
- SS-EN-981 - Safety of machinery - System of auditory and visual danger and information signals
- SS-EN-999 - Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body
- SS-EN-ISO-11161 - Safety of machinery - Integrated manufacturing systems - Basic requirements (ISO 11161:2007)
- SS-EN-ISO-11161-AM1 - Safety of machinery - Integrated manufacturing systems - Basic requirements - Amendment 1 (ISO 11161:2007/Amd 1:2010)
- SS-EN-ISO-11553-1 - Safety of machinery - Laser processing machines - Part 1: General safety requirements (ISO 11553-1:2005)
- SS-EN-ISO-11553-1-AM1 - Safety of machinery - Laser processing machines - Part 1: Laser safety requirements (ISO 11553-1:2020)
- SS-EN-ISO-11553-2 - Safety of machinery - Laser processing machines - Part 2: Safety requirements for hand-held laser processing devices (ISO 11553-2:2007)
- SS-EN-ISO-11553-3 - Safety of machinery - Laser processing machines - Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) (ISO 11553-3:2013)
- SS-EN-ISO-12100 - Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
- SS-EN-ISO-12100-2 - Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles (ISO 12100-2:2003)
- SS-EN-ISO-12100-2-AM1 - Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles - Amendment 1 (ISO 12100-2:2003/Amd 1:2009)
- SS-EN-ISO-13849-1 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
- SS-EN-ISO-13849-2 - Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
- SS-EN-ISO-13850 - Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)
- SS-EN-ISO-13851 - Safety of machinery - Two-hand control devices - Principles for design and selection (ISO 13851:2019)
- SS-EN-ISO-13854 - Safety of machinery - Minimum gaps to avoid crushing of parts of the human body (ISO 13854:2017)
- SS-EN-ISO-13855 - Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010)
- SS-EN-ISO-13856-1 - Safety of machinery - Pressure-sensitive protective devices - Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors (ISO 13856-1:2013)
- SS-EN-ISO-13856-2 - Safety of machinery - Pressure-sensitive protective devices - Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars (ISO 13856-2:2013)
- SS-EN-ISO-13856-3 - Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices (ISO 13856-3:2013)
- SS-EN-ISO-13857 - Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2019)
- SS-EN-ISO-14118 - Safety of machinery - Prevention of unexpected start-up (ISO 14118:2017)
- SS-EN-ISO-14119 - Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013)
- SS-EN-ISO-14120 - Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards (ISO 14120:2015)
- SS-EN-ISO-14121-1 - Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007)
- SS-EN-ISO-14122-1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
- SS-EN-ISO-14122-1-AM1 - Safety of machinery - Permanent means of access to machinery - Part 1: Choice of a fixed means of access between two levels - Amendment 1 (ISO 14122-1:2001/Amd 1:2010)
- SS-EN-ISO-14122-2 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
- SS-EN-ISO-14122-2-AM1 - Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways - Amendment 1 (ISO 14122-2:2001/Amd 1:2010)
- SS-EN-ISO-14122-3 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
- SS-EN-ISO-14122-3-AM1 - Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails - Amendment 1 (ISO 14122-3:2001/Amd 1:2010)
- SS-EN-ISO-14122-4 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
- SS-EN-ISO-14122-4-AM1 - Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders - Amendment 1 (ISO 14122-4:2004/Amd 1:2010)
- SS-EN-ISO-14123-1 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1:2015)
- SS-EN-ISO-14123-2 - Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2:2015)
- SS-EN-ISO-14159 - Safety of machinery - Hygiene requirements for the design of machinery (ISO 14159:2002)
- SS-EN-ISO-14738 - Safety of machinery - Anthropometric requirements for the design of workstations at machinery (ISO 14738:2002/Cor 1:2003, and Cor 2:2005)
- SS-EN-ISO-15537 - Principles for selecting and using test persons for testing anthropometric aspects of industrial products and designs (ISO 15537:2022)
- SS-EN-ISO-16090-1 - Machine tools safety - Machining centres, milling machines, transfer machines - Part 1: Safety requirements (ISO 16090-1:2022)
- SS-EN-ISO-19085-1 - Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:2021)
- SS-EN-ISO-19085-10 - Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO 19085-10:2018)
- SS-EN-ISO-19085-10-AM11 - Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO 19085-10:2018, including Corrected version 2019-12)
- SS-EN-ISO-19085-12 - Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
- SS-EN-ISO-19085-12-AM11 - Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2021)
- SS-EN-ISO-19085-13 - Woodworking machines - Safety - Part 13: Multi-blade rip sawing machines with manual loading and/or unloading (ISO 19085-13:2020)
- SS-EN-ISO-19085-14 - Woodworking machines - Safety - Part 14: Four-sided moulding machines (ISO 19085-14:2021)
- SS-EN-ISO-19085-15 - Woodworking machines - Safety - Part 15: Presses (ISO 19085-15:2021)
- SS-EN-ISO-19085-2 - Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2021)
- SS-EN-ISO-19085-3 - Woodworking machines - Safety - Part 3: Numerically controlled (NC/CNC) boring and routing machines (ISO 19085-3:2021)
- SS-EN-ISO-19085-4 - Woodworking machines - Safety - Part 4: Vertical panel circular sawing machines (ISO 19085-4:2018)
- SS-EN-ISO-19085-5 - Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2017)
- SS-EN-ISO-19353 - Safety of machinery - Fire prevention and fire protection (ISO 19353:2019)
- SS-EN-ISO-20607 - Safety of machinery - Instruction handbook - General drafting principles (ISO 20607:2019)
- SS-EN-ISO-21469 - Safety of machinery - Lubricants with incidental product contact - Hygiene requirements (ISO 21469:2006)
- SS-EN-ISO-23062 - Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment (ISO 23062:2022)
- SS-EN-ISO-4413 - Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
- SS-EN-ISO-4414 - Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
- SS-EN-ISO-7731 - Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
- SS-ENV-1070 - Safety of machinery - Terminology
- SS-ISO-13105-2 - Building construction machinery and equipment - Machinery for concrete surface floating and finishing - Part 2: Safety requirements and verification (ISO 13105-2:2014, IDT)
- SS-ISO-13105-2-AM1 - Building construction machinery and equipment - Machinery for concrete surface floating and finishing - Part 2: Safety requirements and verification (ISO 13105-2:2014/Amd 1:2017, IDT)
- SS-ISO-14159 - Safety of machinery - Hygiene requirements for the design of machinery
- SS-ISO-230-2 - Test code for machine tools - Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes (ISO 230-2:2014, IDT)
- SS-ISO/IEC-15459-2 - Information technology - Unique identifiers - Part 2: Registration procedures (ISO/IEC 15459-2:2015, IDT)
- UNE-EN-ISO-13849-2 - Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
- UNE-EN-ISO-13850 - Safety of machinery - Emergency stop function - Principles for design