FSC Standardization Area MISC: Miscellaneous
The following documents are a part of this series:ASTM:
ISO:
US GOVERNMENT DOCUMENTS:
- A-A-51383 - Neisseria Enrichment Media, Dehydrated
- A-A-51396 - Control Urine Chemistry, Normal
- AA-T-44 - Table, Bedside, Metal (Cancelled, 1958, Superseded By AA-C-10)
- AMS-2759/1 - Heat Treatment of Carbon and Low-Alloy Steel Parts, Minimum Tensile Strength Below 220 ksi (1517 MPa)
- AMS-2759/2 - Heat Treatment of Low-Alloy Steel Parts Minimum Tensile Strength 220 ksi (1517 MPa) and Higher
- AMS-2759/4 - Heat Treatment, Austenitic Corrosion-Resistant Steel Parts
- AMS-2759/5 - Heat Treatment, Martensitic Corrosion-Resistant Steel Parts
- AMS-2759/7 - Carburizing and Heat Treatment of Carburizing Grade Steel Parts
- AMS-2759/8 - Ion Nitriding
- AMS-2762 - Carburizing, Carbon and Low-Alloy Steel Parts (NONCURRENT Jan 2002)
- AN-115 - Shackle - Wire Rope (Cancelled, Superseded by ms-20115)
- AN-2522 - Lens-24 Inch Double Beam (Use ms-25391)
- AN-3057 - Adapter - Electrical Accessory To Cable
- AN-3179 - Inductor, 30 Volt Laboratory Test (Superseded by ms-90306)
- AN-3207 - Cover-Terminal Block
- AN-3216 - Switch, Class D Limit (Superseded by ms-25383)
- AN-3249 - Jack - Tip Voltmeter Test
- AN-3252 - Block - Terminal, Five Stud
- AN-3311 - Relay, 100 Amp, 2Pdt, Hermetically Sealed (Use Ms 24149)
- AN-3352 - Relay, 55 Amp, 2Pst, Unsealed, Class O (Superseded by ms-24178)
- AN-3496 - Inverter - Instrument, Class a, 6 Volt-Amp Single Phase
- AN-365 - Nut, Self-Locking, 250 Degrees F
- AN-427 - Rivet, 100 Deg. Countersunk Head, Steel, Monel and Copper (Use ms-20427)
- AN-504 - Screw, Tapping, Thread Cutting, Round Head, Machine Screw Thread (Inactive for New Design)
- AN-507 - Screw, Machine, Flat Head, 100 Degree
- AN-509 - Screw - Machine, Flat Head, 100 Deg., Structural
- AN-515 - Screw, Machine, Round Head, Coarse Thread (Use ms-35206 ms-35214, ms-35218, ms-51957)
- AN-520 - Screw, Machine, Round Head, Fine Thread
- AN-526 - Screw, Machine, Truss Head (Use ms-35206, ms-35207, ms-35218, ms-35219, ms-51957 and ms-51958)
- AN-550 - Screw Wood, Flat Head, 82 Degree (Use ms-35492 ORMS-35494)
- AN-5532 - Indicator, Engine Synchroscope (Inactive)
- AN-5544 - Generator - Tachometer, Two Pole (Use ms-28054)
- AN-5547 - Generator, Tachometer, Four Pole (Use ms-28054)
- AN-5727 - Glass, Aircraft Instrument Cover (Use ms-28105)
- AN-5769 - Gage, Hydraulic System Pressure (Use ms-28063)
- AN-5771 - Gage, Single, 1-7/8 Dial Pressure (Superseded by MIL-STD-2806)
- AN-5772 - Gage, Dial Indicating, Pressure (Superseded by ms-28064)
- AN-6011 - Gage - Panel Mounting High Pressure Oxygen
- AN-6231 - Scraper - Rod, Hydraulic Piston
- AN-6290 - Gasket - Straight Thread Tube Fitting, Boss (Superseded by ms-28778)
- AN-6560 - Grommet - Washer-Parachute Pack (Use ms-22048)
- AN-658 - Terminal, Wire Rope Swaging, Fork End (Use ms-20658)
- AN-663 - Ball End, Wire Rope, Swaging-Double Shank (Use ms-20663)
- AN-664 - Ball End, Wire Rope, Swaging-Single Shank
- AN-666 - Terminal, Wire Rope, Stud (Use ms-21259)
- AN-667 - Terminal, Wire Rope, Swaging-Fork End (Use ms-20667)
- AN-668 - Terminal, Wire Rope, Swaging-Eye End
- AN-669 - Terminal, Wire Rope, Stud (Cancelled, Use ms-21260)
- AN-773 - Fitting Assembly, Low Pressure Detachable Swivel Hose (Use ms-27404)
- AN-931 - Grommet - Elastic (Superseded by ms-35489)
- ANA-BUL-418 - Differential Pressures
- ANA-BULL-107 - Inspection Standards for Stand & Dissection Tested Self +S/S, 1981, Superseded By MIL-STD-801
- ANA-BULL-112 - Acceptance Standards for Self Sealing Fuel & Oil Cells +S/Susaf 112a) +Superseded By MIL STD
- ANA-BULL-125 - Procedure for Obtaining Qualification Test Approval of Protective Coating Materials Fo
- ANA-BULL-143 - Specifications and Standards, Use of +Superseded by MIL-STD-143+
- ANA-BULL-152 - Numbers, Serial, Aircraft Engine, Instructions for Assignment +Use Milstd 1559+
- ANA-BULL-157 - Colors, List of Standard Aircraft Camouflage (Use Fed-STD-595a)
- ANA-BULL-159 - Nut, Self-Locking, 250 Deg. F (Use MIL-N-25027)
- ANA-BULL-164 - Lubricants, Hydraulic Fluids and Corrosion Inhibitors for Aircraft, Qualifying Procedu
- ANA-BULL-166 - Colors; List of Standard Aircraft Glossy (Cancelled Use Fed-STD-595)
- ANA-BULL-168 - Bolts, an Aeronautical Standard Drawings Reinstated by Thisrevision( )Specification N
- ANA-BULL-177 - Pumps, 200 Gph Power Driven Fuel
- ANA-BULL-178 - Pumps, 400 Gph Power Driven Fuel
- ANA-BULL-179 - Pumps, 700 Gph Power Driven Fuel
- ANA-BULL-182 - Material Changes and Substitutions, Aircraft Engine Parts (Production Contracts)
- ANA-BULL-245 - Certified X-Ray Laboratories
- ANA-BULL-249 - Strainers, Fuel System (Specification an-S-40)
- ANA-BULL-261 - Abbreviations & Contractions for Use on Airborne Equipment,Approved List Of
- ANA-BULL-268 - Fitting Assembly, Low Pressure, Detachable, Hose Standards 1/an6270 an7733
- ANA-BULL-275 - Guide for the Use of Lubricants, Compounds, and Fluids in Aircraft
- ANA-BULL-295 - Coding, Nylon Parachute Cloth Manufacturers Color
- ANA-BULL-302 - Preservation and Packaging Card List for Aeronautical Spares, Form and Instruction For
- ANA-BULL-306 - Engines, Aircraft Turbine and Jet, Designation Of
- ANA-BULL-325 - Nut, Self-Locking, 550 Deg. F +Use MIL-N-25027+
- ANA-BULL-337 - Drawing Status Notes on Air Force-Navy Aeronautical Standarddrawings +Use MIL-STD-32
- ANA-BULL-352 - Engines, Rocket, Liquid Propellant, Designation of +Use MIL-STD-815 Usaf+
- ANA-BULL-360 - Hose End Fittings and Hose Assemblies
- ANA-BULL-386 - Recommended Guide for Location and Actuation of Pilot S Control +Superseded by MIL-STD
- ANA-BULL-388 - Inverters, Rotary +See MIL-I-7032 or QPL-7032+
- ANA-BULL-389 - List of Standardized and Approved Aircraft Ordnance and Chemical and Armament Items
- ANA-BULL-390 - Change, Engineering, To Aircraft +Superseded by Ana 445+
- ANA-BULL-391 - Changes, Engineering, To Aircraft Engines, Propellers and Equipment in Production And
- ANA-BULL-395 - Engine, Aircraft Reciprocating, Designation of +Replaced BYMIL-STD-1557+
- ANA-BULL-400 - Airborne Electronic & Associated Equipment, Applicable Documents
- ANA-BULL-403 - An and Ms Utility Parts Standards for Engines and Propellers, Explanatory Information
- ANA-BULL-406 - Mock-Up, Engine, Construction & Inspection of +Superseded By MIL-STD 1592+
- ANA-BULL-410 - Age Controls for Aeronautical Fuel System Synthetic Rubber Materials +Superseded by An
- ANA-BULL-419 - O Ring Type Packings, Gaskets, and Seals, Identification Of
- ANA-BULL-421 - Atmospheric Properties - Extreme Cold and Hot, Standard Foraeronautical Design +Super
- ANA-BULL-422 - Procedures for Standardized Procurement and Utilization of Aeronautical Engine Contain
- ANA-BULL-423 - Engine, Aircraft, Vendor Substantiation Test for +Supersededby MIL-STD-1529+
- ANA-BULL-424 - Designation, Radio and Radar Equipment Interconnecting Cable+Use MIL-W-5088+
- ANA-BULL-425 - Ms Fitting, Classification of Defects of +Use Milstd 1655+
- ANA-BULL-427 - Age Controls for Synthetic Rubber Parts +Superseded by Ana Bulletin 438+
- ANA-BULL-428 - Engine, Rocket, Liquid Propellant, Design and Installation Criteria For
- ANA-BULL-431 - Fittings, Flared, Classification of Defects Of
- ANA-BULL-432 - Atmospheric Properties - Polar and Tropical Atmospheres, Standard for Aeronautical Des
- ANA-BULL-433 - Overcoding of Standard Drawings
- ANA-BULL-434 - Age Controls of Age Sensitive Elastomeric Items +Use MIL-STD1523+
- ANA-BULL-435 - Inspection Standards for Stand & Dissection Tested Non Selfsealing Type Cells +Superseded By
- ANA-BULL-436 - Quality Standards for Aircraft Tires and Tubes +Superseded by MIL-STD-698+
- ANA-BULL-437 - Procedure for Airframe Contractor S Purchase of Supply Itemsrequiring Qualification Te
- ANA-BULL-440 - Type Designation System for Aeronautical and Support Equipment +Superseded by MIL-STD-
- ANA-BULL-441 - Aeronautical Use of Limitation Notices on Federal and Military Series Specifications A
- ANA-BULL-444 - Electronic Equipment, Piloted Aircraft, Design Criteria For
- ANA-BULL-445 - Engineering Changes To Weapons, Systems, Equipments and Facilities +Superseded by MIL-
- ANA-BULL-446 - Procedure for Submittal and Listing of Industry Specifications and Standards in Ana Bu
- ANC-9 - Aircraft Propeller Handbook
- AND-10000 - Drive - Type 1 Fluid Power Pumps +See Dwg and20000+
- AND-10001 - Mounting Pad and Drive - Type 2 Vacuum and Hydraulic Power Pumps
- AND-10003 - Mounting Pad and Drive - Aircraft Engine Fuel Pump +See Dwgand20003+
- AND-10005 - Mounting Pad & Drive - Aircraft Tachometer +See Dwg and20005+
- AND-10008 - Mounting Pad and Drive - Aircraft Engine Power Take-Off (Flange Type)
- AND-10009 - Mounting Pad and Drive - Small Aircraft Engine Starter
- AND-10010 - Drive-Type Xx Engine Accessory +Cancelled, 1993, No S/S Document+
- AND-10049 - Bosses- Fluid Connection, Internal Straight Thread +Superseded By Ms 33649+
- AND-10064 - Fittings - Installation of Flared Tube, Straight Threaded Connectors +Use Ms21344+
- AND-10065 - Connection Assembly - Flexible, Fluid, Standard Design Of
- AND-10066 - Connectors-Electrical, Receptacles, Integral Mounting +Use Ms33678+
- AND-10074 - Boss Spacing - Hydraulic +Use Ms21343+
- AND-10079 - Terminal - Eye and Fork Cable
- AND-10080 - Fitting - Installation of Universal Elbow +Use Ms21345+
- AND-10082 - Fastener, Installation-Snapslide +Superseded by ms-21327+
- AND-10087 - Screw - Installation & Limitations for Usage of Self Tapping+Cancelled, Use ms-33749
- AND-10102 - Tubing - Standard Dimensions for Round Seamless Alloy Steel
- AND-10104 - Tubing, Steel, Corrosion Resistant, Round Standard Dimensions for (Cancelled, 1994, No Superseding Document)
- AND-10106 - Tubing - Standard Sizes for Aluminum Alloy (52So) Round
- AND-10107 - Tubing - Standard Sizes for Aluminum Alloy (24St) Round
- AND-10108 - Tubing - Standard Sizes for Aluminum Alloy (61S) Round
- AND-10119 - Aluminum Alloy - Standard Conditions and Sizes for Sheet Andstrip (24S)
- AND-10125 - Aluminum Wire - Standard Alloys, Tempers and Sizes of Round and Hexagon (for Welding Rod and General Use)
- AND-10126 - Aluminum Wire - Standard Conditions and Sizes for Sheet, Strip
- AND-10130 - Aluminum Rod and Bar - Standard Alloys, Tempers and Sizes Ofround and Hexagon
- AND-10131 - Aluminum Bar - Standard Alloys, Temper and Sizes of Square
- AND-10132 - Aluminum Bar - Standard Alloy and Temper (24St), and Sizes of Rectangular
- AND-10150 - Starter Diagram - Hand Crank Flexible Shaft
- AND-10201 - Screens - Gaskets - Design Requirements for Carburetor (Cancelled, 1973, No Superseding Document)
- AND-10206 - Plug - Shielded Aircraft Engine Spark +Use MIL-S-7886+
- AND-10210 - Flange-Single 12 Cylinder 3 Bolt Magneto
- AND-10211 - Mounting Flange - Double Type Magneto
- AND-10214 - Coupling Assemblies-Double Type Magneto Drive
- AND-10215 - Mounting Flange-Single Type Magneto (9 and 14 Cyl)
- AND-10216 - Throttle-Handle Design for Engine
- AND-10217 - Plug - 14 mm Shielded Spark +Use MIL-S-7886+
- AND-10219 - Plug - 14 mm British Type Shielded Spark +Use MIL-S-7886+
- AND-10220 - Vapor Pressure Chart
- AND-10221 - Vapor Pressure Correction Chart
- AND-10222 - Fittings - Synthetic Tank General Features of Construction (Superseded in Part (Cover) by by ms-33595 and in Part (Flange) by ms-33596)
- AND-10223 - Levers-Correlation of Power and Condition
- AND-10230 - Reference Chart, Aircraft Engine Accessory Drive +Cancelled,1994, No S/S Document+
- AND-10234 - Template-Propeller Blade Master Male
- AND-10235 - Template-Propeller Blade Female
- AND-10236 - Template Propeller Blade Angle Checking
- AND-10237 - Spline, Serrated (Cancelled, No Replacement)
- AND-10300 - Installation Clearance-Type X Drive
- AND-10306 - Propeller Governor Installation Clearance Aircraft Engine (for Engines of 999 Take Off H.P. or Less)
- AND-10307 - Propeller Governor Installation Clearance - Aircraft Engine (for Engines of 1000 Take Off H.P. or More)
- AND-10312 - Element Installation Clearance-Engine Cylinder Head Temperature Measuring
- AND-10313 - Relief Valve Installation Clearance-Hydraulic
- AND-10328 - Installation Clearance-Type XL-B Drive Magneto
- AND-10332 - Starter-Generator Installation Clearance, Type Xii Drive
- AND-10334 - Installation Clearance-Type Xx Drive Propeller Governor
- AND-10335 - Installation Clearance-Type Xix Drive
- AND-10342 - Regulator Installation Clearance- Dc Generator Voltage
- AND-10355 - Tolerances-Carbon Steel-Sheet and Strip +Use Fed STD 48+
- AND-10360 - Tolerance-Corrosion and Heat Resistant Steel Bars, and Rodsand Wire +Use Fed-STD-48+
- AND-10362 - Tolerances-Carbon Steel Bar and Rod +Use Fed STD 48+
- AND-10367 - Tolerance, Alloy Steel Sheet & Strip +Inactive, Use Fed STD-48+
- AND-10375 - Color-Fluid Line Identification +Use MIL STD 1247+
- AND-10379 - Equivalents-Fraction and Decimal
- AND-10381 - Symbols-Material
- AND-10382 - Gauge Dimensions-Standard Wire and Sheet Metal
- AND-10383 - Cutting Plane-Example For
- AND-10384 - Cross Sectioning-Examples For
- AND-10385 - Alternate Position-Example
- AND-10387 - Drill Sizes - Drilled Hole Tolerances - Twist
- AND-10388 - Lines-Conventional
- AND-10396 - Number-Aircraft Engine Cylinder Location Designation +Use MIL-STD-802+
- AND-10399 - Number Aircraft Engine Location Designation +Use MIL-STD 802+
- AND-10401 - Case-Standards Dimensions for 2-3/4 Dial Instrument
- AND-10402 - Case-Standards Dimensions for 2-3/4 Dial Instrument (With Sump)
- AND-10403 - Case-Standard Dimensions for 1-7/8 Dial Instrument +Use Ms 33638+
- AND-10404 - Pointers-Standard Design of Aircraft Instrument +Use Ms33585+
- AND-10406 - Thermocouple Leads-Iron-Constantan, Installation Of
- AND-10407 - Insulator - Installation of Vibration
- AND-10410 - PITOT-Static and Pitot Tube Wiring Diagram For
- AND-10411 - Wiring Diagram-Percent Type Tachometer Indicator and Two Pole Tachometer Generator
- AND-10412 - Case - 2-Inch Size Instrument, Standard Dimensions for +Usems33598+
- AND-10413 - Instrument-Flight, Basic, Standard Arrangements of +Superseded by Ms 33635+
- AND-10425 - Insert Arrangements-Electrical Connector, Shell Sizes 8S, 10S, and 10Sl +Use Ms33680+
- AND-10426 - Insert Arrangements-Electrical Connector, Shell Sizes 12S and 12 +Use Ms33881+
- AND-10428 - Insert Arrangements - Electrical Connector, Shell Sizes 16S and 16 (Use ms-33683)
- AND-10429 - Insert Arrangements-Electrical Connector, Shell Size 18 +Usems33684+
- AND-10431 - Insert Arrangements-Electrical Connector, Shell Size 22 +Usems33686+
- AND-10432 - Insert Arrangements-Electrical Connector, Shell Size 24 +Usems 33687+
- AND-10433 - Insert Arrangements-Electrical Connector, Shell Size 28 +Usems33688+
- AND-10434 - Insert Arrangements - Electrical Connector, Shell Size 32 (Use ms-33689)
- AND-10435 - Insert Arrangements - Electrical Connector, Shell Size 36 (Use ms-33690)
- AND-10436 - Insert Arrangements-Electrical Connector Shell Size 40 +Superseded by Ms 33691+
- AND-10437 - Insert Arrangements-Electrical Connector Shell Size 44 +Superseded by Ms 33692+
- AND-10438 - Insert Arrangements-Electrical Connector Shell Size 48 +Superseded by Ms 33693+
- AND-10439 - Receptacle Installation-Fuel Nozzle Grounding +Use Ms 33645+
- AND-10440 - Insert Design-Electrical Connector, Shell Size 18, Arrangement 16 +Use Ms33694+
- AND-10441 - Battery Installation
- AND-10443 - Contacts-Video Coaxial Connector +Use Ms33695+
- AND-10444 - Insert Arrangements - Electrical and Coaxial Connector, Shell Size 32 (Use ms-33696)
- AND-10445 - Sump Jar-Installation of Battery
- AND-10446 - Compass Wiring Diagram-Remote Indicating Magnetic
- AND-10447 - Tachometer and Synchroscope Wiring Diagram-Single and Multi-Engine
- AND-10448 - Indicator Wiring Diagram- Air Position
- AND-10450 - Indicator Wiring Diagram-Electric Direct Current Turn and Bank
- AND-10451 - Compass Wiring Diagram-Gyro Fluxgate
- AND-10458 - Mounting Pad-Oil Connection, 3 and 4, Stud
- AND-10459 - Connectors-Electrical, Plugs, Integral Mounting +Use Ms33679+
- AND-10461 - Connections - Input Power Airborne Electronic Equipment, 28 V Dc, 115 V Single Phase Ac, and/or 115/200 V 3 Phase Ac (Use ms-25245)
- AND-10462 - Plug-External Power, Ac, Wiring of +Superseded by ms-17793+
- AND-10477 - Cross Recess-Dimensions For
- AND-10478 - Instrument-Electrical Indicating, Requirements for Sealed (Radio and Radar)
- AND-10481 - Standard Dimensioning System for Extruded Sections
- AND-10482 - Turnbuckles, Lock Wiring of +Use Ms 33591+
- AND-10483 - Wiring Diagram-Torque Pressure, Manifold Pressure and Fuel Flow Indicating Systems
- AND-10550 - Rim Contours-Type I Main Landing Gear Wheel
- AND-10551 - Rim Contours-Type I Tail Wheel
- AND-10552 - Rim Contours-26X6 Type Ii Landing Gear Wheel
- AND-10553 - Rim Contours-30X7 and 32X8 Type Ii Landing Gear Wheel
- AND-10554 - Rim Contour-34 X 9 Type Ii Landing Gear Wheel
- AND-10558 - Rim Contour - 10 X 3 Type Ii Tail Wheel
- AND-10559 - Rim Contours - 10-1/2 X 4, 12-1/2 X 4-12 X 5 Type Vii Extrahigh Pressure Tail Wheel
- AND-10561 - Rim Contour-7.00-6 (Type Iii Low Pressure) Main Landing Gearwheel +Use and 10562+
- AND-10568 - Rim Contours - Type Iv Main Landing Gear and Tail Wheels
- AND-10570 - Rim Contours - Type VI (Low Profile) Nose Wheel
- AND-10574 - Rim Contour - 17-1-2 X 6-1-2 Type Vii (Extra High Pressure)Tail Wheel
- AND-10584 - Rim Contours, 52 X 16 and 56 X 16, Type Vii, Extra High Pressure, Main Landing Gear Wheel
- AND-10600 - Trunnion Assembly-Camera
- AND-10601 - Wedge - Instrument Mounting
- AND-10602 - Stud - Vertical Aerial Camera Mount
- AND-20005 - Drive - Type Xv Engine Accessory +Cancelled, 1993, No S/S Document+
- AND-20007 - Drive - Type Xvii Engine Accessory +Cancelled, 1993, No S/Sdocument+
- ANSI-Z17.1 - Preferred Numbers
- AS-8700 - Installation and Test of Electronic Equipment in Aircraft, General Specification for (STABILIZED Sep 2013)
- BU-101 - Fastener Defects, Classification of (Use MIL-F-8490)
- BU-102 - Engines, Aircraft, Pulsejet, Specifications and Standards Applicable To
- BU-104 - Clothing Defects, Classification Of
- BU-105 - Environmental Testing, Aeronautical and Associated Equipment, General Specification For
- BU-106 - General Environmental Criteria for Guided Missile Weapon Systems
- BU-115 - Environmental Criteria for Ground Support Equipment
- BU-116 - Statical Sampling Plan, Aircraft Engines and Related Equipment (Use MIL-E-8970)
- BU-117 - Power Unit, Liquid Propellant, Specifications and Standardsapplicable To
- BU-121 - Mockup Test Procedures, Electric-System, Preparation Of
- BU-122 - Hydraulic Systems, Missile, Specifications and Standards
- BU-123 - Specifications and Standards Applicable To Solid Propellant Rocket Engines, Use of
- BU-124 - Aircraft Data Required for Design of Flight Simulators (Use MIL-D-23143)
- BU-125 - Repair and Rework of Aluminum and Magnesium Alloy Castings (With Information Notice 1)
- BU-126 - Use of Chromium or Nickle Plating for Salvage Purposes
- BU-127 - Preparation of Usaf Standard Aircraft Flight Simulator Characteristics Formats (Orange
- BU-129 - Weapon System Functional Area Index
- BU-131 - Quality Control Requirements for Aluminum Alloy Sheet With Surface Imperfections
- BU-134 - Standardized Nomenclature, Symbols and Units of Radiometric Quantities in Specification
- BU-138 - Specifications and Standards Applicable To Aircraft Propeller, Use Of
- BU-139 - Dynamic Test Procedure, Package Cushioning Materials
- BU-140 - Air Force Equipment Technical Information File Applicable To
- BU-29 - Codes for Aircraft Finishing Schemes (Use MIL-STD-1516)
- BU-49 - Codes for Ground Equipment Finishing Schemes
- BU-506 - Reliability Monitoring Program for Use in the Design, Development, and Production of A
- BU-511 - Engines, Aircraft, Gas Turbine Design and Installation Criteria for
- BU-513 - Master Packing List Requirements for Ground Electronic Equipment
- BU-515 - Control of Nonconforming Supplies (Use MIL-STD-1520)
- BU-518 - Cargo, Aircraft Compartment Dimensional Data
- BU-519 - Bibliography of Reliability Documents for Use in the Design, Development, and Production
- BU-52 - Aerospace Vehicle Manufacturers Code Letters
- BU-520 - Calibration and Certification of Measuring and Testing Equipment
- BU-523 - Space Environmental Criteria for Aerospace Vehicles
- BU-524 - Utilization Guide for Training Equipment, Instructions for Preparation Of
- BU-526 - Contaminants, Cabin Air, Maximum Allowable Concentration Of
- BU-527 - Liquid Oxygen Compatibility Impact Sensitivity Test Method (Use ASTM-D2512)
- BU-528 - Fitting, Hose, Tetrafluoroethylene, High Temperature Medium Pressure, Classification Of
- BU-530 - Verification Testing of Parachute Textile Materials (Use MIL-STD-1525)
- BU-536 - Criteria Documents Used in Aeronautical Systems Part O Specifications
- BU-54 - Code Symbols for Chromium Plates Aircraft Engine Cylinders (Specification No. 20031)
- BU-89 - Power Requirements for Airborne Equipment
- BU-90 - Color Codes, Manufactures Identification, Nylon Webbing (Use MIL-STD-1480)
- BU-94 - Textile Defects, Classification of (Use Fed-STD-4)
- BU-95 - Parachute Defects, Classification of (Use MIL-STD-849)
- BU-99 - An Fittings, Classification of Defects of (Superseded by Ana Bulletin 431)
- CAA-293 - Fan Marker Transmitter, Specification For
- CS-119 - Dial Indicators (for Linear Measurements)
- DDD-W-415 - Wiping Cloths, Cotton (Cancelled, Superseded By DDD-R-30)
- DD-G-496 - Glasses, Gage, Reflex and Round, Tank (for Pressures Under 125 Pounds)
- DD-G-616 - Glasses, Medicine +Superseded by DD-M-200+
- DI-MISC-80000 - Data Item Descriptions (Dids)
- DI-MISC-80001 - Military Specification (Superseded by DI-SDMP-80001)
- DI-MISC-80006 - Producibility Program Plan
- DI-MISC-80036 - Validation Report (Cancelled, 1989, Superseded by DI-CMAN-80792)
- DI-MISC-80043 - Ammunition Data Card
- DI-MISC-80048 - Scientific and Technical Reports Summary
- DI-MISC-80056 - Request for Approval of Nonstandard General Purpose Electronic Test Equipment
- DI-MISC-80058 - Chemical Materiel Surveillance Program Plan (Cancelled, Use DI-Misc-80489)
- DI-MISC-80059 - Passenger or Cargo Forecast of Channel Mac Transportation Requirements
- DI-MISC-80060 - Ammunition Test Expenditure Report
- DI-MISC-80062 - Cash and Headcount Controls
- DI-MISC-80071 - Parts Approval Requests
- DI-MISC-80072 - Program Parts Selection List (Ppsl)
- DI-MISC-80073 - Armor Material Test Reports
- DI-MISC-80074 - Manufacturing Plan
- DI-MISC-80093 - DOD Property Record (Partial)
- DI-MISC-80094 - Revised Technical Data for Rebuilt Industrial Plant Equipment
- DI-MISC-80098 - Notice of Claimed Investigational Exemption for a New Drug (Ind)
- DI-MISC-80099 - New Drug Application (Nda)
- DI-MISC-80113 - Night Vision Imaging System: (NVIS) Compatible Aircraft Interior Lighting Compliance Data
- DI-MISC-80123 - Medical and Health Plan
- DI-MISC-80124 - Equipment Management Command Objectives
- DI-MISC-80128 - Work Measurement Performance Report (Cancelled, Superseded by DI-Misc-80295)
- DI-MISC-80129 - Subscriber Education Pamphlet
- DI-MISC-80136 - Traffic Measurements and Analysis Report
- DI-MISC-80137 - Call Detail Recording Data
- DI-MISC-80146 - Delivery Order Proposal
- DI-MISC-80158 - Precision Measurement Equipment Laboratory (Pmel) Report
- DI-MISC-80159 - Command Status Report
- DI-MISC-80162 - Design Producibility Analysis Report
- DI-MISC-80163 - Design Producibility Programs Plan
- DI-MISC-80167 - Contract Data Status and Schedule Report
- DI-MISC-80168 - Data Management Plan
- DI-MISC-80169 - Still Photo Coverage
- DI-MISC-80170 - 35mm Slide Transparencies
- DI-MISC-80171 - Materiel Deterioration Prevention Plan
- DI-MISC-80176 - Camouflage Line Art Data
- DI-MISC-80192 - Color Photograph Prints
- DI-MISC-80193 - Inventory Listing of Bulk Propellant and Propelling Charges
- DI-MISC-80208 - Requisition Summary Report
- DI-MISC-80209 - War Reserve Material Report
- DI-MISC-80215 - Energy Information Report
- DI-MISC-80226 - Propulsion Unit Data
- DI-MISC-80228 - Pest Control Summary Report
- DI-MISC-80246 - Ballistic Acceptance Test Report
- DI-MISC-80260 - Tuberculosis Detection and Control Report
- DI-MISC-80268 - Special (Factory) Test Equipment Documentation
- DI-MISC-80279 - Utilities Outage and Status Report
- DI-MISC-80295 - Work Measurement Labor Performance Report
- DI-MISC-80296 - Design Data and Calculations
- DI-MISC-80324 - Follower Source Selection Plan
- DI-MISC-80325 - Industry Solicitation Package
- DI-MISC-80326 - Industry Response Evaluations
- DI-MISC-80327 - Follower Contracting Cost Projections
- DI-MISC-80328 - Follower Certification Plan
- DI-MISC-80329 - Follower Certification
- DI-MISC-80330 - Technology Transfer Plan
- DI-MISC-80343 - Multiplex Interface Control Document (MICD)
- DI-MISC-80344 - Acquisition Streamlining Cost Benefit Assessment Report
- DI-MISC-80350 - Anchor Stomp Tasking Report
- DI-MISC-80353 - Deep Space Sensor Tasking Response Report
- DI-MISC-80354 - Outside Plant Equipment Installation Plan
- DI-MISC-80358 - Document Changes
- DI-MISC-80359 - Equipment Failure Information Report (Efir)
- DI-MISC-80367 - Implementation Management Plan
- DI-MISC-80370 - Safety Engineering Analysis Report
- DI-MISC-80371 - Volunteer Registry
- DI-MISC-80372 - Physician Assistant Supervisor Report
- DI-MISC-80380 - Chemical Surety Material Consumption and Usage Report
- DI-MISC-80381 - Unfired Pressure Vessel Inspection Report
- DI-MISC-80382 - Boiler Inspection Report
- DI-MISC-80383 - Boiler and Pressure Vessel Activity Management Report
- DI-MISC-80388 - Analysis of Data
- DI-MISC-80390 - Oil Analysis Report
- DI-MISC-80392 - Operating Instructions
- DI-MISC-80393 - Master Document List (Mdl)
- DI-MISC-80394 - Disaster Preparedness Exercise Evaluation Report
- DI-MISC-80406 - Innovations Report (Cancelled, Superseded by DI-Misc-80407)
- DI-MISC-80407 - Innovations Certifications
- DI-MISC-80411 - Contamination Control Plan
- DI-MISC-80413 - Polychlorinated Biphenyl (Pcb) Inventory Report
- DI-MISC-80414 - Polychlorinated Biphenyl (Pcb) Inspection Report
- DI-MISC-80416 - Telecommunications Service Request (Tsr)
- DI-MISC-80418 - Communications - Electronics Authorization Program (Cap) Administrative Changes
- DI-MISC-80419 - Base Communications-Computer Systems (C-Cs) Assessment
- DI-MISC-80420 - Circuit Order In-Effect/Exception/Delayed Service Report
- DI-MISC-80421 - Communications Outage Reports
- DI-MISC-80422 - Telephone Directory
- DI-MISC-80431 - Pollution Incident Report
- DI-MISC-80434 - Airfield Construction Closure Report
- DI-MISC-80443 - Housekeeping and Cleaning Schedule
- DI-MISC-80446 - Report of Supplies Used
- DI-MISC-80472 - Space Object Identification (Soi) Discrimination (Soidis) Report
- DI-MISC-80480 - Fire Incident Reports
- DI-MISC-80484 - Pretest Survey Report
- DI-MISC-80485 - Communications-Computers Systems Installation Records
- DI-MISC-80487 - D028 Central Leveling System
- DI-MISC-80488 - Special Level File Maintenance Transaction Reporting
- DI-MISC-80489 - Stocked Item Storage and Serviceability Analysis
- DI-MISC-80504 - Data Load Worksheet
- DI-MISC-80508 - Technical Report - Study/Services
- DI-MISC-80519 - Power Plant Operation and Maintenance Report
- DI-MISC-80522 - Operations Positional Reference Handbooks (Oprh)
- DI-MISC-80523 - Operations Checklists
- DI-MISC-80524 - System Performance Analysis Report (Spar)
- DI-MISC-80526 - Parts Management Plan
- DI-MISC-80533 - Pension Plan Data Report
- DI-MISC-80536 - Food Service Operations Report
- DI-MISC-80538 - Dining Facility Summary Checklist
- DI-MISC-80541 - Inventory Count Worksheet
- DI-MISC-80543 - Food Service Customer Surveys
- DI-MISC-80557 - Commercial Support Documentation (Csd)
- DI-MISC-80563 - Materials Research and Development Report
- DI-MISC-80564 - Survivability Analysis Report
- DI-MISC-80565 - Survivability Program Plan
- DI-MISC-80573 - Armed Forces Consumer Level Subsistence Appraisal Committee (Afclsac) Report
- DI-MISC-80574 - Facility Inventory Report
- DI-MISC-80575 - Us Air Force Menu Utilization Report (Mur)
- DI-MISC-80576 - Unsatisfactory Material Report (Subsistence)
- DI-MISC-80591 - Fire Hazard/Deficiency Inspection Report
- DI-MISC-80597 - Parts, Materials and Processed Standardization and Control Program Plan
- DI-MISC-80598 - Contractor-Selected Parts, Materials and Processes List
- DI-MISC-80599 - Nonpreferred Part Approval Request
- DI-MISC-80600 - Part Drawings
- DI-MISC-80601 - Proposed Changes To Program Parts Control Board Controlled Drawing
- DI-MISC-80602 - Parameter Drift Screening Plan
- DI-MISC-80608 - Medical Workload Report
- DI-MISC-80611 - Provider Qualifications/Limitations
- DI-MISC-80613 - Standard Change Form
- DI-MISC-80652 - Technical Information Report
- DI-MISC-80653 - Test Reports
- DI-MISC-80657 - Stock Number Users Directory (Snud) Reconciliation
- DI-MISC-80672 - Gas Turbine Engine Steady State and Transient Performance Presentations for Digital Computer Programs
- DI-MISC-80678 - Certification/Data Report
- DI-MISC-80703 - Laminating Process Description (Boats)
- DI-MISC-80704 - Parts Usage Report
- DI-MISC-80705 - Certification Data for Non-Nuclear Level I Material (Cancelled,1991, Superseded by DI-Misc-81020)
- DI-MISC-80711 - Scientific and Technical Reports
- DI-MISC-80714 - Documentation and Manifesting of Non-U.S. Government Cargo
- DI-MISC-80716 - Transportation Shipment and Routing Instructions
- DI-MISC-80722 - DOD Summary No-Loss Fire Emergencies Report
- DI-MISC-80730 - System Test Plan (Cancelled, Superseded by DI-NDTI-80808)
- DI-MISC-80732 - Translation of Foreign Language Documents
- DI-MISC-80733 - Warranty Status Report (Cancelled, 1991, Superseded by DI-MNTY-81217)
- DI-MISC-80734 - Technical Data Assessment
- DI-MISC-80738 - Magnetic Tape Cartridges, Video Data and Voice Records
- DI-MISC-80748 - Engineering Services Memorandum (ESM)
- DI-MISC-80749 - Specifications and Standards Usage Report
- DI-MISC-80750 - Technical Data Package Review Report
- DI-MISC-80751 - English Language Test Design Document (Eltd)
- DI-MISC-80752 - Specification Requirement Sheet (Srs) (Cancelled, 1991, Superseded by DI-EGDS-81181)
- DI-MISC-80758 - Reliability Qualified Items List
- DI-MISC-80759 - Contractor Validation Plan
- DI-MISC-80760 - Flash Report
- DI-MISC-80761 - Test Scheduling Report
- DI-MISC-80819 - Watercraft Operations Cost and Summary Report
- DI-MISC-80820 - Sales Rate Calculations
- DI-MISC-80821 - Water Use Report
- DI-MISC-80836 - Health Care Needs Assessment Data Collection/Analysis Plan
- DI-MISC-80837 - Health Care Needs Assessment Results Report
- DI-MISC-80838 - Needs Assessment Modeling Procedure
- DI-MISC-80839 - System Security Management Plan (Ssmp)
- DI-MISC-80840 - Preliminary System Security Concept (Pssc)
- DI-MISC-80841 - Security Vulnerability Analysis
- DI-MISC-80842 - Adversary Mission Analysis
- DI-MISC-80843 - Depot Technical Data Control Manuals
- DI-MISC-80844 - Depot Technical Data Control Manual Outline
- DI-MISC-80845 - Technical Orders (Supplemental Data)
- DI-MISC-80847 - Integrated Tactical Warning and Attack Assessment (Tw/AA) System Interface Control Document
- DI-MISC-80852 - Endurance Fuel Calculations (Non-Nuclear Ships)
- DI-MISC-80853 - Heat Balance Calculations and Flow Diagrams for Main Propulsion Plant Systems (Steam Driven Ships)
- DI-MISC-80854 - Modification Proposal
- DI-MISC-80856 - Design To Cost (Dtc) Plan
- DI-MISC-80857 - Design To Cost (Dtc) Status Report
- DI-MISC-80875 - Welding Procedures
- DI-MISC-80876 - Welding Procedure Qualification Test Report
- DI-MISC-80904 - VALIDATION NOTICE 1 FOR BASE
- DI-MISC-80914 - Small Arms Serialization Program (SASP) Transaction Card
- DI-MISC-80915 - Status Report for Contractor Receipt/Shipment of Foreign Military Sales (FMS) Repair/Return Assets
- DI-MISC-80919 - Implementation Plan
- DI-MISC-80923 - Radiation Testing Tracking System Transaction
- DI-MISC-80945 - Magnetic Tape Report
- DI-MISC-80946 - Launch Vehicle Post-Flight Analysis
- DI-MISC-80963 - Re-Entry Vehicle Data Report
- DI-MISC-80996 - Propellant Analysis Report for Aircrew Escape Propulsion (Aeps) Devices
- DI-MISC-81015 - Serialization Plan
- DI-MISC-81016 - Lot Summary Inspection Record
- DI-MISC-81020 - Certification Data for Non-Nuclear Level I Material
- DI-MISC-81049 - Family Housing Inventory Designation and Assignment Report
- DI-MISC-81050 - Family Housing Inventory and Occupancy Report
- DI-MISC-81051 - Linen Exchange Inventory Report
- DI-MISC-81052 - Commissary Operating Statement
- DI-MISC-81053 - Unaccompanied Personnel Housing Inventory and Utilization Data
- DI-MISC-81054 - Certificate of Gains, Losses and Discrepancies
- DI-MISC-81055 - Library Collection Development Selection Scheme and Central Funds Budget Submission
- DI-MISC-81056 - Annual Library Report
- DI-MISC-81058 - Non-Standard Parts Test Data Report
- DI-MISC-81061 - Enclosure System Implementation Plan
- DI-MISC-81062 - Backplane Assembly Implementation Plan
- DI-MISC-81063 - Backplane Component Implementation Plan
- DI-MISC-81064 - Support Hardware Implementation Plan
- DI-MISC-81107 - Inventory/Utilization Data Report
- DI-MISC-81108 - Computerized Target Description
- DI-MISC-81109 - Radiographic Inspection Report for Aircrew Escape Propulsion (Aeps) Devices
- DI-MISC-81113 - Radar Spectrum Management (Rsm) Test Plan
- DI-MISC-81114 - Radar Spectrum Management (Rsm) Control Plan
- DI-MISC-81119 - Sky-Wave Propagation Charts
- DI-MISC-81123 - Color Coordination Manual(S) for Habitability Spaces
- DI-MISC-81174 - Frequency Allocation Data
- DI-MISC-81176 - Manufacturing Technology Report
- DI-MISC-81180 - Manufacturing Technology Demonstration Plan
- DI-MISC-81183 - Integrated Master Schedule (Ims)
- DI-MISC-81184 - Methodology for Cockpit Thermal Assessments
- DI-MISC-81189 - Master Engineering Document Lists (MEDL)
- DI-MISC-81190 - Ships, Certificates of Ad Measurement
- DI-MISC-81191 - Training Device Inventory Checklist/Record (ICL/R)
- DI-MISC-81192 - Test Proposal for Pilot Pack
- DI-MISC-81206 - Still Photographic Records
- DI-MISC-81210 - List of Piping Descriptions
- DI-MISC-81214 - Construction Progress and Material Test Report
- DI-MISC-81215 - Lubrication List
- DI-MISC-81239 - Automated Invoices
- DI-MISC-81240 - Motor Log Book
- DI-MISC-81241 - Airworthiness Directive/Service Bulletins/Advisory Data
- DI-MISC-81258 - Value Engineering Program Plan
- DI-MISC-81259 - Value Engineering Study Proposal
- DI-MISC-81260 - Value Engineering Program Status Report
- DI-MISC-81274 - Environmental Permits
- DI-MISC-81275 - Technical Videotape Presentation
- DI-MISC-81276 - As-Designed Parts, Materials, and Processes List (ADPMPL)
- DI-MISC-81277 - Parts, Materials, and Processes Selection List (Pmpsl)
- DI-MISC-81281 - Aircraft Trainer Criteria Report
- DI-MISC-81283 - Specification Requirement Verification Matrix
- DI-MISC-81301 - Scoring Summary Report
- DI-MISC-81302 - Target Equipment Modification Status Report
- DI-MISC-81303 - System Flights/Readiness Status Information Report
- DI-MISC-81304 - Target/Aircraft Telemetry Data Report
- DI-MISC-81305 - Manual Target/Aircraft Flight Status Report
- DI-MISC-81310 - Personnel Recruitment Advertising Management Plan
- DI-MISC-81311 - Personnel Recruitment Advertisement
- DI-MISC-81312 - Collateral Personnel Recruitment Literature
- DI-MISC-81317 - Information Systems Acceptance, Commissioning and Removal Certificate
- DI-MISC-81318 - Material Cure-Date Certification Report
- DI-MISC-81319 - Avionics Systems Installation, Interface, and Test Specifications
- DI-MISC-81321 - Equipment Installation Instructions
- DI-MISC-81337 - Consolidated Automated Support System Tracking (Casstrac) Data
- DI-MISC-81338 - Master Instrument List (MIL)
- DI-MISC-81341 - Informal Security Policy Model
- DI-MISC-81342 - Descriptive Top Level Specification
- DI-MISC-81345 - Covert Channel Analysis Report
- DI-MISC-81346 - Formal Security Policy Model
- DI-MISC-81347 - Formal Top Level Specification
- DI-MISC-81348 - Philosophy of Protection Report
- DI-MISC-81356 - Certificate of Compliance
- DI-MISC-81358 - Ground Launch Flight Report
- DI-MISC-81371 - Maintenance Data Collection Record (MDCR)
- DI-MISC-81381 - Site Survey Report (Ssr)
- DI-MISC-81382 - Work Schedule
- DI-MISC-81384 - Service Engineering Report (Ser)
- DI-MISC-81385 - Demobilization Plan
- DI-MISC-81386 - Standard Contract Data for Input To Special Tooling/Special Test Equipment (St/Ste) Management System
- DI-MISC-81387 - Airframe Rigidity Test Report
- DI-MISC-81388 - Flight Flutter Test Report
- DI-MISC-81389 - Flutter Model Test Report
- DI-MISC-81390 - Flutter Analysis Report
- DI-MISC-81391 - Analytical Condition Inspection Report
- DI-MISC-81392 - Contractor Operation and Maintenance of Simulators/Equipment Management Status Report
- DI-MISC-81397 - Hazardous Materials Management Program (HMMP) Report
- DI-MISC-81414 - Operation and Maintenance Instructions for Research and Development (R&D) Equipment
- DI-MISC-81417 - Minimum Equipment Subsystem List (MESL)
- DI-MISC-81418 - Operating Procedures Manual
- DI-MISC-81419 - Personnel Report
- DI-MISC-81423 - Facilities Maintenance Report
- DI-MISC-81454 - Automated Computer Program Identification Number (ACPIN) Data and Control Record
- DI-MISC-81456 - Student Guide
- DI-MISC-81457 - Lesson Strategy Report
- DI-MISC-81458 - Instructor Planning Document
- DI-MISC-81459 - Syllabus
- DI-MISC-81460 - Electronic Warfare (Ew) Training Equipment Report
- DI-MISC-81461 - Fuel Chit Report
- DI-MISC-81462 - Aircraft Progress Report
- DI-MISC-81463 - Mission Flight Operations Summary Report
- DI-MISC-81479 - Ozone Depleting Substances (ODS) Plan
- DI-MISC-81480 - Status Update Report (SUR)
- DI-MISC-81481 - Configuration Marriage Record
- DI-MISC-81485 - Durability and Damage Tolerance Test Results Report
- DI-MISC-81486 - Durability Analysis Report
- DI-MISC-81487 - Damage Tolerance Analysis Report
- DI-MISC-81489 - Real Property Facilities As-Built Drawings
- DI-MISC-81499 - Packaging Kit Contents List
- DI-MISC-81506 - Base Electronic System Engineering Plan (Besep)
- DI-MISC-81507 - Mass Properties Data Report (Submarines)
- DI-MISC-81511 - Allied Ordnance Publication (AOP-12) Aircraft Stores Interface Manual (Asim)
- DI-MISC-81512 - Allied Ordnance Publication (AOP-11) Interoperability of North Atlantic Treaty Organization (NATO Aircraft and Stores Manual)
- DI-MISC-81538 - Special Tooling (St) Report for Electronic Tooling Information Management System (Etims)
- DI-MISC-81539 - Special Test Equipment (Ste) Report for Electronic Tooling Information Management System (Etims)
- DI-MISC-81558 - Leisure Travel in Conjunction With Official Military Travel
- DI-MISC-81562 - Temporary Non-Standard Modification Documentation and Marking Requirements for Test Equipment in Aerospace Vehicles and Related Ground Support Equipment
- DI-MISC-81579 - Digital Imaging
- DI-MISC-81592 - Thermal Survey Report
- DI-MISC-81608 - Theory of Design and Operation (Tdo)
- DI-MISC-81612 - Research and Developement (R&D) Project Summary
- DI-MISC-81614 - Craft Acceptance Test Schedule
- DI-MISC-81615 - Craft Trial Report
- DI-MISC-81616 - Purchase Order (Po)
- DI-MISC-81617 - Equipment Operational Log
- DI-MISC-81618 - Service Bulletins
- DI-MISC-81620 - Craft Test Status Report
- DI-MISC-81621 - Test Change Proposal (Tcp)
- DI-MISC-81622 - Test Problem Report (Tpr)
- DI-MISC-81623 - Craft Construction Schedules
- DI-MISC-81624 - Notification of Test/Trials
- DI-MISC-81627 - System Deficiency Report (Sdr) Data
- DI-MISC-81630 - Craft Acceptance Test Index
- DI-MISC-81664 - Cabinet Shipment Record
- DI-MISC-81688 - Key and Certificate Management Plan (KCMP)
- DI-MISC-81692 - Fail-Safe Design and Analysis (Fsda)
- DI-MISC-81709 - Revised Additional Data for Technical Publication
- DI-MISC-81710 - Custom Microcircuit Procurement Plan
- DI-MISC-81762 - Security Evaluation Document (SED)
- DI-MISC-81807 - Software/Firmware Change Request
- DI-MISC-81832 - Counterfeit Prevention Plan
- DI-MISC-81863 - Contractual Shipping Documentation
- DI-MISC-81920 - List of All Deliverables
- DI-MISC-81940 - Welder Performance Qualification and Training Program
- DI-MISC-81943 - Trip/Travel Report
- DI-MISC-81966 - Gas Turbine Engine Steady State and Transient Performance Presentations for Computer Programs
- DI-MISC-82003 - Maintenance Data Collection Record (MDCR)
- DI-MISC-82020 - Material and Processing Digital Data Package (MPDDP)
- DI-MISC-82104 - Site Survey Report (SSR)
- DI-MISC-82120 - Paint Preservation Appendices Report
- DI-MISC-82124 - Joint Precision Approach and Landing System (JPALS) Certification Plan
- DI-MISC-82126 - Government Air Segment (AS) Hardware in the Loop (HITL) System Support Plan (HSSP)
- DI-MISC-82127 - Master Engineering Document List (MEDL)
- DI-MISC-82226 - Voyage Schedule Plan
- DI-MISC-82257 - Hose Management Database Report
- DI-MISC-82386 - Certification Data Report
- DOD-E-8983 - Electronic Equipment, Aerospace, Extended Space Environment, General Specification For
- DOD-HDBK-178 - Quantitative Description of Obscuration Factors for Electro-Optical and Millimeter Wave Systems (Metric)
- DOD-HDBK-345 - MIL-STD-1567, Work Measurement Verification and Compliance Plan
- DOD-M-24680 - Metric Machinery/Equipment, General Requirements for (Cancelled, 1990, No Superseding Document
- DOD-STD-1399/301 - Interface Standard for Shipboard Systems Section 301a Ship Motion and Attitude (Superseded by MIL-STD-1399/301 (Metric))
- DOD-STD-1476 - Metric System, Application in New Design
- DOD-STD-1690 - Maritime Metric Practice Guide (Cancelled, 1992, Superseded by ASTM-F1332)
- DOD-STD-1700 - Data Management Program
- DOD-STD-1702 - Integrated Logistics Support Programs for Equipment, Subsystems, and Systems (Metric)
- DOD-STD-1768 - Procedures for Development of Depot Technical Data
- DOD-STD-2137 - Mass Properties Technical Requirements for Surface Ships (Cancelled, 1993, Superseded by MIL-STD-2137)
- DOD-STD-2167 - Defense System Software Development (Cancelled, 1994, Superseded by MIL-STD-498)
- DOD-STD-963 - Data Item Descriptions (DIDs), Preparation of
- EIA-748 - Earned Value Management Systems
- FED-STD-1 - Standard for Laboratory Atmospheric Conditions for +Cancelled, 04/09/86, Superseded By ASTM-E
- FED-STD-104 - Conservation of Automotive Gasoline(Canceled, No Superseding Documen
- FED-STD-116 - Mattress, Bed (Felted, Cotton) (No Superseding Document)
- FED-STD-136 - Flame-Spread Properties of Materials
- FED-STD-147 - Tape, Packaging, Adhesive & Gummed, Methods of Inspections,Sampling, & Testing
- FED-STD-149 - Syringe, Luer, Interchangeable Component, Dimensions Of
- FED-STD-158 - Cements, Hydraulic, Sampling, Inspection & Ttesting +Superseded By ASTM+
- FED-STD-160 - Rubber Products, Definitions and Terms for Visible Defects of (No Superseding Document)
- FED-STD-186 - Marking of Valves, Fittings, Flanges, & Unions Used in Nuclear Reactor Systems
- FED-STD-187 - Identification of Pressed Bends, Forms, Seams, & Joints, (Sheet Metal)
- FED-STD-304 - Metal, Chemical Test Methods (for Identification) +Cancelled, 06/06/77, No S/S Doc.+
- FED-STD-313 - Material Safety Data, Transportation Data, and Disposal Data for Hazardous Materials Furnished to Government Activities
- FED-STD-358 - Sampling Procedures
- FED-STD-368 - Quality Control System Requirements
- FED-STD-376 - Preferred Metric Units for General Use by the Federal Government
- FED-STD-5 - Standard Guides for Preparation of Proposed Item Logistics Data Records
- FED-STD-793 - Depot Storage Standards
- FED-STD-800 - Terms, Definitions & Symbols for Security Equipment & Practices
- GGG-T-561 - Tools, Blacksmiths and Horseshoers +Cancelled, 1958, Superseded ByGGG-T-563
- IEEE-260 - IEEE Standard Letter Symbols for Units of Measurement (Superseded by IEEE-260.1)
- IEEE-945 - Recommended Practice for Preferred Metric Units for Use in Electrical and Electronics
- IEEE-SI10 - IEEE/ASTM American National Standard for Metric Practice (Pod)
- MIL-A-26669 - Acoustical Noise Tests, Aeronautical and Associated Equipment (Use MIL-STD-810)
- MIL-A-4777 - Album, Photographic Print, Type A-2
- MIL-A-9837 - Analytical Overhaul
- MIL-B-12547 - Binders, Load, Lever-Type (Cancelled, No Superseding Document)
- MIL-B-17668 - Brass Casting, Commercial (Superseded by QQ-B-621)
- MIL-B-2263 - Balling Gun, Veterinary
- MIL-B-2562 - Bandage, Cotton (Derby)
- MIL-B-6947 - Bronze, Aluminum, Castings Aircraft (Superseded by QQ-B-671)
- MIL-B-9862 - Binder, Loose Leaf, Fabric Hinge, Five Ring (No Superseding Document)
- MIL-BUL-400 - Airborne Electronic and Associated Equipment, Applicable Documents (No Superseding Document)
- MIL-BULL-100 - List of Specification and Standard Approved by the Naval Sea Systems Command (OS) (Cancelled, 1984, No Superseding Document)
- MIL-BULL-147 - Specifications & Standards of Non-Government Organizations Released for Flight Vehicle
- MIL-BULL-343 - DOCUMENTS APPLICABLE TO AIRCRAFT ENGINES AND PROPELLERS, USEOF (CANCELLED, NO SUPERSEDING DOCument).
- MIL-BULL-418 - Differential Pressures
- MIL-C-12992 - Cable Assembly, Power, Electrical (Cord CX-227/TVQ-1)
- MIL-C-13335 - Coating for Magnesium and Magnesium Alloys
- MIL-C-18104 - Control, Tracking Recorder C-1388/ASB-1A
- MIL-C-18159 - Chemical Cleaning of Salt Water Piping Systems (Contents of Spec Have Been Incorp Into MIL-STD-2187)
- MIL-C-18244 - Control and Stabilization Systems: Automatic, Piloted Aircraft, General Specification For
- MIL-C-18591 - Carbon Monoxide Elimination, Requirement for (Superseded by ms-800)
- MIL-C-1901 - Cable, 1-Conductor, Submarine Mine m4 (Buna S Synthetic Rubber Insulated)
- MIL-C-19874 - Cleaning Requirements for Nuclear Primary Coolant Equipment Including Piping Systems
- MIL-C-24133 - Calibration Procedures, Preparation of (Superseded by MIL-M-38793)
- MIL-C-2598 - Cutter, Molar, Extractor and Handle, Veterinary
- MIL-C-26261 - Combat Control Central an-FSQ-32(V)
- MIL-C-27171 - Chart, Standard Missile Characteristics, Preparation of (No Superseding Document)
- MIL-C-27439 - Computer, Performance, Multijet, General Specification For
- MIL-C-27958 - Communication Central an/MRC-107 (No Superseding Document)
- MIL-C-3660 - Case Section, Mailing, Microscope Slide
- MIL-C-46384 - Calibration Technical Bulletins and Related Engineering Services (Superseded by MIL-M-63037)
- MIL-C-60248 - Calibration Equipment, Commercial and Commercially-Modified
- MIL-C-82177 - Commercial Repair Parts Support, General Specification for (No Superseding Document)
- MIL-D-10167 - Drawings, Manufacturers, for Electronics Command Equipment
- MIL-D-11203 - Drawings and Data Lists, Reproducible, Preparation of (for Tank and Automotive Materiel).
- MIL-D-11345 - Drawings, Signal Corps Nnd Supplementary Data, Manufacturer Prepared.
- MIL-D-13570 - Dust, Testing by Exposure To (Superseded by MIL-STD 810)
- MIL-D-18300 - Design Examinations, Engineering Avionic Systems/Equipment General Requirements For
- MIL-D-19731 - Data Sheets for Aircraft and Missile Systems Support Equipment (No Superseding Document)
- MIL-D-22688 - Data, Avionics Design Requirements for Developing Aviation Training Devices (No Superseding Document)
- MIL-D-26715 - Discriptive Identification Data To Be Furnished by Government Suppliers (No Superseding Document)
- MIL-D-5028 - Drawings and Data Lists, Preparation of Manufacturers (for Production Aeronautical and Associated Equipment) (Asg)
- MIL-D-55124 - Drawings, Contractor Design Activity, for Signal Corps Equipment (Use MIL-D-1000)
- MIL-D-55176 - Data, Electronics Command Engineering Document Control (No Superseding Document)
- MIL-D-7018 - Drawings, for Avionics Equipment, Procurement of (Use MIL-D-1000)
- MIL-D-8706 - Data and Tests, Engineering, Contract Requirements for Aircraft Weapon Systems
- MIL-D-9402 - Design of Electrical Equipment in Aircraft, General Specification for (Use MIL-E-25499C)
- MIL-D-9863 - Decalcomanias for Technical Information File of Ground Support Equipment (No Superseding Document)
- MIL-E-20003 - Extractors, Ruptured Cartridge, Mark Ii, Mark Iv, and Caliber .50, m5.
- MIL-E-22843 - Equipment, Low Noise Level (Shipboard) Superseded by MIL STD 740a
- MIL-E-25499 - Electrical System, Aircraft, Design and Installation of, General Requirements for (No Superseding Document)
- MIL-E-26144 - Electric Power, Missile, Characteristics and Utilization, General Specification For
- MIL-E-26338 - Electric Power, Portable Supply, Characteristics Of
- MIL-E-26362 - Electric Power, for Utilization Equipment, Characteristics of (Use MIL-E-4158)
- MIL-E-26491 - Electrical Load Analysis, Ground Equipment, Requirements For
- MIL-E-27073 - Electronic Modules, Ground Electronic Equipment General Specification For
- MIL-E-38453 - Environmental Control, Environmental Protection, & Engine Bleed Air Systems, Aircraft, General Specification for (Superseded by MIL-E-87145)
- MIL-E-60106 - Engineering, Service, Calibration Equipment, General Specification for (No Superseding Document)
- MIL-E-7080 - Electric Equipment, Aircraft, Selection and Installation of (Superseded by MIL-STD-7080)
- MIL-E-83210 - Equipment, Electronic, Criteria for the Utilization of Micro/Molecular Electronic Technology
- MIL-E-8970 - Engine and Related Propulsion and Power Equipment, Aircraft, Acceptance Tests of, Sampling Plan for, Statistical
- MIL-E-917 - Electric Power Equipment, Basic Requirements for (Renumbered MIL-DTL-917)
- MIL-F-1413 - File, Dog, Toenail
- MIL-F-2390 - Forceps, Splinter
- MIL-F-2517 - Float, Dental, Veterinary
- MIL-F-25381 - Flight Testing, Electric System, Piloted Aircraft and Guided Missile, General Requirements for (No Superseding Document)
- MIL-F-2551 - Forceps, Wolf-Tooth, Veterinary
- MIL-F-5656 - Felt, Wool (for Aircraft Applications) (Superseded by C-F-206)
- MIL-F-9882 - Food Service Attendants (No Superseding Document)
- MIL-F-9892 - Food Service Contracts
- MIL-H-24148 - Human Engineering Requirements for Bureau of Ships Systems and Equipment (Superseded by MIL-H-46855)
- MIL-H-2558 - Hook, Neurectomy (Veterinary)
- MIL-H-2608 - Handpieces, Dental Engine
- MIL-H-27894 - Human Engineering Requirements for Aerospace Systems and Equipment (Use MIL-H-46855)
- MIL-H-47143 - Heat Treating, Type D6Ac Alloy Steel, Processes for (No Superseding Document)
- MIL-H-8729 - Hi&Valu Item Application Summary. Preparation Of
- MIL-HDBK-1 - Cross Index of Chemically Equivalent Specifications and Identification Code (Ferrous and Nonferrous Alloys) (Handbook H-1)
- MIL-HDBK-111 - Value Engineering
- MIL-HDBK-115 - US Army Reverse Engineering Handbook (Guidelines and Procedures)
- MIL-HDBK-1280 - Keyboard Arrangements
- MIL-HDBK-140 - Security Classification and Cognizant Activity of Electronic Equipment (No Superseding Document)
- MIL-HDBK-152 - Office Duplicating Processes (No Superseding Document)
- MIL-HDBK-153 - Office Copying Processes and Equipment
- MIL-HDBK-1763 - Aircraft/Stores Compatibility: Systems Engineering Data Requirements and Test Procedures
- MIL-HDBK-1785 - System Security Engineering Program Management Requirements
- MIL-HDBK-201 - Petroleum Operations
- MIL-HDBK-206 - Gear Tooth, Load Ratings (Except Aeronautical Applications) (No Superseding Document)
- MIL-HDBK-216 - Rf Transmission Lines and Fittings (Including Change Notice 1 Thru Change Notice 10) (No Superseding Document)
- MIL-HDBK-221 - Fire Protection Design Handbook for U.S. Navy Aircraft Powered by Turbine Engines
- MIL-HDBK-245 - Preparation of Statement of Work (Sow)
- MIL-HDBK-248 - Acquisition Streamlining (No Superseding Document)
- MIL-HDBK-25 - Glossary of Photographic Terms Including Document Reproduction (No Superseding Document)
- MIL-HDBK-259 - Life Cycle Cost in Navy Acquisitions
- MIL-HDBK-266 - Application of Reliability - Centered Maintenance To Naval Aircraft, Weapon Systems and Support Equipment (Superseded by MSIL-STD-2173)
- MIL-HDBK-275 - Guide for Selection of Lubricants, Fluids, and Compounds for Use in Flight Vehicles and Components
- MIL-HDBK-276/1 - Life Cycle Cost Model for Defense Materiel Systems Data Collection Workbook
- MIL-HDBK-276/2 - Life Cycle Cost Model for Defense Materiel Systems Operating Instructions
- MIL-HDBK-300 - Technical Information File of Support Equipment
- MIL-HDBK-318 - Cargo Aircraft Compartment Dimensional Data (NO SUPERSEDING Document)
- MIL-HDBK-319 - Guide for Preparation and Processing on Air Force Electronic Equipment Type Designation Requests (MIL-STD-196) (See Notice for Replacement Information
- MIL-HDBK-333/1 - Handbook for Standardization of Nondestructiv (Canc, 1987, Superseded by MIL-HDBK-728/1 Thru
- MIL-HDBK-333/2 - Handbook for Standardization of Nondestructiv (Canc, 1987, Superseded by MIL-HDBK-728/1 Thru
- MIL-HDBK-336/1 - Survivability, Aircraft, Nonnuclear, General Criteria-Volume 1
- MIL-HDBK-336/2 - Survivability, Aircraft, Nonnuclear, Airframe-Volume 2
- MIL-HDBK-336/3 - Survivability, Aircraft, Nonnuclear, Engine-Volume 3
- MIL-HDBK-402 - Guidelines for the Implementation of the DOD Parts Control Program (Superseded by MIL-HDBK-512, Sd-19)
- MIL-HDBK-50 - Evaluation of a Contractor's Quality Program (No Superseding Document)
- MIL-HDBK-505 - Definitions of Item Levels, Item Exchangeability, Models, and Related Terms
- MIL-HDBK-51 - Evaluation of a Contractor's Inspection System (Handbook H51) (No Superseding Document)
- MIL-HDBK-52 - Evaluation of Contractor's Calibration System (No Superseding Document)
- MIL-HDBK-694 - Aluminum and Aluminum Alloys (No Superseding Document)
- MIL-HDBK-727 - Design Guidance for Producibility
- MIL-HDBK-766 - Design To Cost (No Superseding Document)
- MIL-HDBK-881 - Work Breakdown Structures for Defense Materiel Items
- MIL-I-16910 - Interference Measurement, Electromagnetic, Methods and Limits (Use MIL-STD-461, 462, and 463)
- MIL-I-17623 - Interference Measurement, Electrumagnetic, Methods and Limits, for Electric Office Machines, Printing and Lithographic Equipment (Use MIL-STD-461, MIL-STD-462, and MIL-STD-463)
- MIL-I-27337 - Intercommunication Set an-AIC-18 Bench, Preflight, and Flight Tests of (No Superseding Document)
- MIL-I-6143 - Insignia and Marking for Search and Rescue Aircraft, Design Requirements For
- MIL-I-82110 - Interim Repair Parts Support, General Specification For
- MIL-I-8500 - Interchangeability and Replaceability of Component Parts for Aerospace Vehicles
- MIL-I-8677 - Installation of Armament Control Systems and Associated Equipment in Naval Aircraft (No Superseding Document)
- MIL-I-8700 - Installation and Test of Electronic Equipment in Aircraft, General Specification for (Superseded by SAE-as8700)
- MIL-J-83302 - Job Performance Aids, Advanced-Type, for Vnaf Organizational Maintenance
- MIL-L-17192 - Lubrication Design, Lubricants, & Lubrication Information for Electronic Equipment, General Specification - Use MIL-STD 454
- MIL-L-9875 - Liquid Oxygen&Nitrogen Generating and Charging Equipment, General Specification for Maintainability Features of (No Superseding Document)
- MIL-M-11266 - Macroetch Test and Macrographs for Steel Bars, Billets and Blooms. Superseded by MIL-STD-430.
- MIL-M-13231 - Marking of Electronic Items (Superseded by MIL-STD-13231)
- MIL-M-13749 - Metal Powder, Ferrous, Sintered, Structural Parts
- MIL-M-21255 - Modification Kit for Radar Sets an/APS-38 and an/APS-38a
- MIL-M-23313 - Maintainability Requirements for Shipboard and Shore Electronic Equipment and Systems
- MIL-M-23530 - Mock-Up of Main and Auxiliary Shipboard Machinery Spaces
- MIL-M-25500 - Mockup Testing, Electrical System, Piloted Aircraft and Guided Missile, General Requirements for (No Superseding Document)
- MIL-M-26512 - Maintainability Requirements for Aerospace Systems and Equipment (Superseded by MIL-STD-471)
- MIL-M-28787/50 - Module, Electronic, Standard Hardware Program Driver, Interface, Digital, Key Code Qdg
- MIL-M-46849 - Microfilming of Engineering and Related Documents, 16mm Requirements for (No Superseding Document)
- MIL-M-55214 - Maintainability Requirements, General, for Electronic Equipment (Superseded by MIL-STD 470, 471 or MIL-HDBK 472)
- MIL-M-58014 - Maintenance Package for Transportation Corps Equipment.
- MIL-M-63007 - Manuals, Technical: Hand Receipt (-Hr), Preparation of (No Superseding Document)
- MIL-M-8090 - Mobility, Towed Aerospace Ground Equipment, General Requirements for (Superseded by SAE-as8090)
- MIL-M-82527 - Maintenance Requirements Cards (Mrc S) and Maintenance Index Pages (Mip S), Development and Preparation of (Navord Planned Maintenance System) (Use MIL-P-24534)
- MIL-N-17506 - Nickel-Copper-Aluminum Alloy, Wrought (Superseded by QQ-N-286)
- MIL-N-25076 - Nameplate, Identification, Metallic Foil, Adhesive-Backed (Superseded by MIL-P-19834)
- MIL-N-7513 - Nomenclature Assignment, Contractors Method for Obtaining (Superseded by MIL-STD-1812)
- MIL-O-23626 - Overhaul and Repair of Radar Set an/MPS-11a (Use MIL-R-82173)
- MIL-P-11422 - Peptone
- MIL-P-13421 - Packaging of Set Eng 6 No. 330-010 (Canvas Worker,S Equipment, Set No.1)
- MIL-P-15137 - Provisioning Technical Documentation for Repair Parts for Electrical and Mechanical Equipment (Naval Shipboard Use) (No Superseding Document)
- MIL-P-17900 - Production Data Package (No Superseding Document)
- MIL-P-17993 - Provisioning Technical Documentation Requirements and Procedures
- MIL-P-21873 - Provisioning, Initial Support, General Requirements for (Use MIL-STD-1375)
- MIL-P-21873/1 - Provisioning, Initial Support, General Requirements for (Use MILSTD-1375)
- MIL-P-23189 - Pert/Time and Pert/Cost Management Information Systems for Planning and Control (Navy) (No Superseding Document)
- MIL-P-23302 - Procurement Packages for Aeronautical Spare Parts, Requirements For
- MIL-P-24014 - Preclusion of Hazards From Electromagnetic Radiation To Ordnance, General Requirements for (Use MIL-STD-1385)
- MIL-P-24052 - Preliminary Plans and Test Procedure Requirements for Radiac Instruments (No Superseding Document)
- MIL-P-24310 - Provisioning Monitoring System Procedures for Naval Shipboard Electrical and Mechanical Equipment and Components (Superseded by MIL-STD-2186)
- MIL-P-25797 - Propulsion Engine Requirements, Air Vehicle, Specification for, Outline and Instructions for Preparationof
- MIL-P-28700 - Personnel Planning Data for Naval Systems (No Superseding Document)
- MIL-P-28759 - Planned Maintenance Subsystem (Pms) for Shore and Shipboard Equipment Maintenance Requirement Cards (Mrc S) and Maintenance Index Pages (Mip S) Preparation and Contents of (Use MIL-P-24534)
- MIL-P-38785 - Provisioning, Phased (Superseded by MIL-STD-1517)
- MIL-P-82313 - Publications, Technical, for Training Devices (Cancelled, 1970, Superseded by MIL-M-82376)
- MIL-P-84000 - Provisioning Screening Data To Be Furnished by Government Suppliers (No Superseding Document)
- MIL-R-10002 - Radar Trial Fire Training Kit PH-645( )/Gp
- MIL-R-11471 - Radiographic Inspection of Metals (Superseded by MIL-STD-453)
- MIL-R-18136 - Research and Engineering Reports, Format and General Requirements (Use MIL-STD-847)
- MIL-R-22973 - Reliability Index Determination for Avionic Equipment Models, General Specification For
- MIL-R-23094 - Reliability Assurance for Production Acceptance of Avionic Equipment, General Specification for (Superseded by MIL-STD-781a)
- MIL-R-24358 - Restoration Shipboard Electronic Equipment F, 1N and 2N Cognizance (Superseded by MIL-STD-2110)
- MIL-R-25703 - Reconnaissance Equipment, Selection of Materials, Parts, and Procedures for Approval
- MIL-R-25956 - Report, Nonmilitary Crystal Unit Specification
- MIL-R-26260 - Rocket Research Vehicle XRM-86
- MIL-R-26273 - Radar Set an/Fps-63
- MIL-R-27070 - Reliability Requirements for Development of Ground Electronic Equipment (Superseded by MIL-STD-785)
- MIL-R-27430 - Receiving Set, Radio an-ARN-58 Bench, Preflight, and Flight Tests Of
- MIL-R-27542 - Reliability Program for Systems, Subsystems and Equipment (Superseded by MIL-STD-785
- MIL-R-55231 - Reliability Requirements, General, for Production Electronic Equipment (Superseded by MIL-STD-785)
- MIL-R-55413 - Reliability Prediction and Demonstration for Airborne Surveillance System (Multipurpose) MQM-58a
- MIL-R-55611 - Report, Technical (Cancelled, 12/8/83, No Replacement)
- MIL-R-82109 - Repair Parts Usage Data Reporting, General Specification For
- MIL-R-82188 - Repair Parts Support During Service Test and Initial Period of Operation, General Specification For
- MIL-R-83313 - Reviews and Audits, Technical, for Communication-Electronic-Meteorological Systems and Related Equipment (See Notice 2 for Replacement Information)
- MIL-R-978 - Reports: Research and Development (for Electronic Equipment) (Superseded by MIL-STD-847)
- MIL-S-10234 - Shutter Assembly, an/GVA-1( )
- MIL-S-11459 - Spare Parts Data (Transportation Corps Equipment).
- MIL-S-12348 - Suppression, Radio Interference General Requirements for Railway Rolling Stock, and Maintenance of Way Equipment (Superseded by MIL-STD-461)
- MIL-S-13237 - Supression, Radio Interference Requirements for Watercraft (Superseded by MIL-E-55301)
- MIL-S-17724 - Sight, Illuminated Mark 20 Mod 4
- MIL-S-19393 - Support, Waveguide Horn, for as-473/ASB-1 (No Superseding Document)
- MIL-S-2040 - Specifications for Quartermaster Corps Maintenance Manuals End Parts Lists.
- MIL-S-23603 - System Readiness/Maintainability, Avionic Systems Design, General Specification for (Superseded by MIL-STD-471)
- MIL-S-23747 - Screw-Thread, Modified, 60 Degrees Stub, Double (Use MIL-STD-1373)
- MIL-S-24277 - Standarization Program for Ships Shipb Oard Systems and Equipments, Requirements for (Use MIL-STD-680)
- MIL-S-25287 - Source Data for Aircraft and Allied Equipment To Support Nuclear Weapon Capabilities, General Preparation Of
- MIL-S-25288 - Source Data for Allied Equipment Used With Fighter and Bomber Aircraft Carrying Nuclear Weapons, Detail Preparation Of
- MIL-S-25292 - Source Data for Practice Bombs and Bomblets, Detail Preparation Of
- MIL-S-25293 - Source Data for Bomb Trailers, Detail Preparation Of
- MIL-S-25793 - Specifications and Engineering Data for Environmental Control and Protection Systems for Air Vehicles,Instructions and Requirements For
- MIL-S-2633 - Stopper, Rubber, for Vaccine Bottle (With Sleeve and Hollow Core).
- MIL-S-26634 - Specifications, Weapon System, and Support System Mockups, Preparation Of
- MIL-S-26640 - Specification, Electronic Support Systems, Preparation Of
- MIL-S-26799 - Supply Test Support Table, Preparation Of
- MIL-S-27074 - Scale Models, General Specification for (No Superseding Document)
- MIL-S-3350 - Syringe, Veterinary, (Dose, Metal)
- MIL-S-38130 - Safety Engineering of Systems and Associated Subsystems and Equipment, General Requirements for (Superseded by MIL-STD-882)
- MIL-S-38711 - Screening Data To Be Furnished by Government Suppliers (Use MIL-P-84000a)
- MIL-S-4456 - Shock, Variable Duration, Method and Apparatus for (Use MIL-STD-202)
- MIL-S-55135 - Same Number Inadvertently Assigned These Two Specs (Weaponsight Infrared 21 Jun 61 FSC 5850 Superseded by MIL-W-55145) (Scaleplates 31 Jul 61 FSC 6625 Superseded by MIL-S-55170)
- MIL-S-55556 - Specification, Preparation of Installation and Acceptance Testing of Electronics Equipment in Aircraft (No Superseding Document)
- MIL-S-55612 - Selection of Parts, Materials, and Processes Used in Electronic Equipment (Use MIL-P-11268g)
- MIL-S-6644 - Specification, Equipment, Contractor Prepared, Instructions for the Preparation Of
- MIL-S-6745 - Switches: Aircraft Toggle (Superseded by MIL-S-3950)
- MIL-S-8048 - Specifications, Aeronautical Weapon Systems, Preparation Of
- MIL-S-81127 - Simulator, Launcher and Missile Mark 6 Mod 2 (No Superseding Document)
- MIL-S-81398 - Standardization Program Plans (Use Milstd 680)
- MIL-S-8169 - Specifications, Detail, Guided Missile,Preparation Of
- MIL-S-83490/1 - Specification, Types and Forms, Navsea Xws and Ws Series (Superseded by MIL-STD-961)
- MIL-S-83490/2 - Specification, Types and Forms, Military (Os) Series (Superseded by MIL-STD-961)
- MIL-S-8512 - Support Equipment, Aeronautical, Special, General Specification for the Design Of
- MIL-S-8577 - Searchlight Positive Carbon Control Modification Equipments for an/AVQ-2 and an/AVQ-2a Sets
- MIL-S-9867 - Support Packages Preparation Of
- MIL-STD-1260 - Uniform Cost Accounting and Reporting System (Ucars) (No Superseding Document)
- MIL-STD-1280 - Keyboard Arrangements (Superseded by MIL-HDBK-1280)
- MIL-STD-1281 - Internal Transient Control for Solid State Power Supplies (No Superseding Document)
- MIL-STD-1302 - Reports, Pump Design Evaluation for Naval Shipboard Centrifugal Pumps (No Superseding Document)
- MIL-STD-1303 - Painting of Naval Ordnance Equipment
- MIL-STD-1305 - Magnetoresistive Devices, Definitions, Letter Symbols, Color Code and Circuit Symbol for Part 1 Magnetoresistors (No Superseding Document)
- MIL-STD-1308 - Material Application and Processing Requirements (Classified, see your contracting officer)
- MIL-STD-1314 - Safety Precaution for Explosive Loaded Items (Use DOD Manual 4145.26m)
- MIL-STD-13231 - Marking of Electronic Items
- MIL-STD-1339 - Fitting Out Procedures-Ships
- MIL-STD-1340 - Fitting Out Procedures Ship Conversions and Modernizations (Superseded by MIL-STD-1339)
- MIL-STD-1345 - Test Requirements Document, Preparation of (No Superseding Document)
- MIL-STD-1351 - Replaceable Electronic Assembly Description and English Language Test Program Requirements
- MIL-STD-1375 - Provisioning, Initial Support, General Requirements for (No Superseding Document)
- MIL-STD-1381 - Technical Electronic Terms and Definitions (No Superseding Document)
- MIL-STD-1399/101 - Interface Standard for Shipboard Systems Section 101 Cooling Water for Support of Electronic Equipment (Superseded by DOD-STD-1399-532)
- MIL-STD-1399/102 - Interface Standard for Shipboard Systems Section 102 Low Pressure Dry Air Service for Surface Ships
- MIL-STD-1399/103 - Interface Standard for Shipboard Systems Section 103 Electric Power, Alternating Current
- MIL-STD-1399/104 - Interface Standard for Shipboard Systems Section 104 Potable Water Service (Superseded by DOD-STD-1399, Section 533)
- MIL-STD-1399/105 - Interface Standard for Shipboard Systems Section 105 Sea Water Service for Surface Ships (No Superseding Document)
- MIL-STD-1399/106 - Interface Standard for Shipboard Systems Section 106 Compressed Air Service for Surface Ships (No Superseding Document)
- MIL-STD-1399/108 - Interface Standard for Shipboard Systems Section 108 Sewage/Waste Disposal for Surface Ships (Superseded by MIL-STD-1399, Section 593 - Part 1)
- MIL-STD-1399/201 - Interface Standard for Shipboard Systems Section 201 Compartment Ambient Conditions for Support of Electronic Equipment (Superseded by MIL-STD-1399, Section 204)
- MIL-STD-1399/204 - Interface Standard for Shipboard Systems Section 204 Ambient Air Conditions in Surface
- MIL-STD-1399/401 - Interface Standard for Shipboard Systems Section 401 D.C. Magnetic Field Environment (Superseded by DOD-STD-1399, Section 070-Part 1)
- MIL-STD-1399/408 - Interface Standard for Shipboard Systems Section 408 Electromagnetic Radiation Hazards To Personnel and Fuels (No Superseding Document)
- MIL-STD-1399/409 - Interface Standard for Shipboard Systems Section 409 Electromagnetic Radiation Hazards To Ordnance (No Superseding Document)
- MIL-STD-1399/501 - Interface Standard for Shipboard Systems Section 501 Nomenclature, Electronic and Weapons Control Functions (No Superseding Document)
- MIL-STD-1399/502 - Interface Standard for Shipboard Systems Section 502 Electronic Systems Parameters
- MIL-STD-1399/505 - Interface Standard for Shipboard Systems Section 505 Central Time and Frequency Support (Superseded by MIL-STD-1399/441)
- MIL-STD-1399/701 - Interface Standard for Shipboard Systems Section 701 Ship Speed Data Transmission (Superseded by MIL-STD-1399, Section 702)
- MIL-STD-1399/702 - Interface Standard for Shipboard Systems Section 702 Synchro Data Transmission
- MIL-STD-1406 - Retroreflectivity Test (No Superseding Document)
- MIL-STD-143 - Standards and Specifications, Order of Precedence for the Selection of (Superseded by MIL-STD-970)
- MIL-STD-1454 - Calorimetry For Thermal Battery Heat Sources Test and Calibration Procedures
- MIL-STD-1476 - Metric System Application in New Design (No Superseding Document)
- MIL-STD-1513 - Trade Studies for the Selection of Avionic Test Support Systems, Criteria for (No Superseding Document)
- MIL-STD-1517 - Phased Provisioning (Superseded by MIL-STD-1388/1 and MIL-STD-1388/2)
- MIL-STD-1519 - Test Requirements Document, Preparation of (No Superseding Document)
- MIL-STD-1528 - Manufacturing Management Program
- MIL-STD-1536 - Integral Sensor Test System (No Superseding Document)
- MIL-STD-1552 - Provisioning Technical Documentation, Uniform DOD Requirements for (Superseded by MIL-STD-1388-2a)
- MIL-STD-1553 - Digital Time Division Command/Response Multiplex Data Bus
- MIL-STD-1555 - Aircrew Station Displays and Associated Equipment, Definitions of (No Superseding Document)
- MIL-STD-1559 - Numbers, Serial, Aircraft Gas Turbine Engine and Engine Module Assignment of (Superseded by MIL-HDBK-1559)
- MIL-STD-1561 - Provisioning Procedures, Uniform DOD (No Superseding Document)
- MIL-STD-1567 - Work Measurement (No Superseding Document)
- MIL-STD-1600 - Reliability Predition of Monolithic Integrated Circuits (See MIL-HDBK 217)
- MIL-STD-1602 - Progress Reports for Research and Development Equipment, Requirements for (No Superseding Document)
- MIL-STD-1604 - Technical and Maintenance Overhaul and Repair Standards, Preparation of (Superseded by MIL-M-24784/9)
- MIL-STD-1607 - Chemical Cleaning Of Main and Auxiliary Boilers (Sulfamic-Citric Acid Method
- MIL-STD-1656 - Validation Plans for Naval Ordnance Overhaul and Repair Activities, Preparation Of
- MIL-STD-167 - Mechanical Vibrations of Shipboard Equipment (Replaced by MIL-STD-167/1 and MIL-STD-167/2)
- MIL-STD-1671 - Schematic Wiring Diagram (External Dc Power Connector, Aircraft) (No Superseding Document)
- MIL-STD-170 - Moisture Resistance Test Cycle for Ground Signal and Electronic Test Equipment (Superseded by MIL-STD-810)
- MIL-STD-173 - Systems for Painting and Finishing Artillery Materiel
- MIL-STD-1763 - Aircraft/Stores Certification Procedures (Superseded by MIL-HDBK-1763)
- MIL-STD-1771 - Value Engineering Program Requirements (No Superseding Document)
- MIL-STD-1785 - System Security Engineering Program Management Requirements (Superseded by MIL-HDBK-1785)
- MIL-STD-180 - Photographic Equipment, Classification of Visual and Mechanical Defects For
- MIL-STD-1806 - Marking Technical Data Prepared by or for the Department of Defense (No Superseding Document)
- MIL-STD-1812 - Type Designation, Assignment and Method for Obtaining (Superseded by MIL-HDBK-1812)
- MIL-STD-1836 - Standardization and Control Program for Parts, Materials and Processes Used in Intercontinental Ballistic Missile Weapons Systems (Superseded by MIL-STD-1546)
- MIL-STD-185 - Continuous Identification Marking of Copper and Copper Base Alloys
- MIL-STD-188/101 - Military Communication System Technical Standards Common Long Haul(Dcs)/Tactical Reference Circuit Standard
- MIL-STD-204 - Thickness of Sheet and Strip Metals
- MIL-STD-2076 - Unit Under Test Compatibility With Automatic Test Equipment General Requirements for (No Superseding Document)
- MIL-STD-2078 - Requirement for Preparation of Support Equipment Depot Level Rework Standards (No Superseding Document)
- MIL-STD-2080 - Maintenance Plan Analysis for Aircraft and Ground Support Equipment - Withdrawn in 1986, No replacement
- MIL-STD-2110 - Restoration, Overhaul, and Repair of Electronic Equipment
- MIL-STD-2137 - Weight Control Technical Requirements for Surface Ships (Superseded by ASTM-F1808, SAWE-Rp12 and SAWE-Rp13)
- MIL-STD-216 - Production or Procurement of Artwork for Technical Manuals (Superseded by MIL-M-38784)
- MIL-STD-243 - Type and Definition of Models for Communication Electronic Equipment (Use MIL-STD-280)
- MIL-STD-254 - Weight and Balance Data Reporting Forms for Aircraft (Asg) (Superseded by MIL-STD-1374)
- MIL-STD-255 - Electric Voltages Alternating and Direct Current (No Superseding Document)
- MIL-STD-27 - DESIGNATIONS FOR ELECTRIC POWER SWITCHGEAR DEVICES and INDUSTRIAL CONTROL DEVICES (SUPERSEDED BYANSI C37.20)
- MIL-STD-280 - Definitions of Item Levels, Item Exchangeability, Models, and Related Terms (Superseded by MIL-HDBK-505)
- MIL-STD-295 - Bill of Material, Preparation of (No Superseding Document)
- MIL-STD-32 - Status Notes for Use on Military Sheet Form Standards (Use MIL-STD-962)
- MIL-STD-337 - Design To Cost (No Superseding Document)
- MIL-STD-399 - Microform Formats (No Superseding Document)
- MIL-STD-40000 - Parts Control Program for Nondevelopmental Items (Ndis) (Superseded by MIL-HDBK-402)
- MIL-STD-405 - Riveting, Rocket and Guided Missile Structural, Aluminum and Aluminum Alloy Blind Rivets, Mechanically Expanded Type
- MIL-STD-415 - Test Provisions for Electronic Systems and Associated Equipment, Design Criteria for (No Superseding Document)
- MIL-STD-419 - Cleaning, Protecting, and Testing Piping, Tubing, and Fittings for Hydraulic Power Transmission Equipment
- MIL-STD-437 - X-Ray Standard for Bare Aluminum Alloy Electrode Welds
- MIL-STD-440 - Soldering Techniques for Standard Type Solder Terminals (Use MIL-STD-454)
- MIL-STD-443 - Rating Conditions for the Design of Refrigeration and Air Conditioning Field Equipment
- MIL-STD-446 - Enviromental Requirements for Electronic Parts (No Superseding Document)
- MIL-STD-447 - Definitions of Interchangeable Substitute and Replacement Items (Superseded by MIL-STD-721B)
- MIL-STD-448 - Tests for Construction, Industrial, and Materials Handling Equipment (No Superseding Document)
- MIL-STD-451 - Weight and Balance Data Reporting Forms for Rotorcraft (Superseded by MIL-STD-1374)
- MIL-STD-456 - Electronic Parts, Date and Source Coding for (Superseded by MIL-STD-1285)
- MIL-STD-473 - Maintainability Verification/Demonstration/Evaluation for Aeronautical Systems (Superseded by MIL-STD-471)
- MIL-STD-499 - Engineering Management
- MIL-STD-643 - Evaluation of Contractor Quality Control Systems
- MIL-STD-646 - Electrical Circuit (Wire Marking) Identification for Tactical Military Vehicles
- MIL-STD-673 - Hole Numbering System-Perforated Paper Tape (No Superseding Document)
- MIL-STD-678 - Printer, Projection, Photographic
- MIL-STD-680 - Standardization Program Requirements for Defense Acquisitions (No Superseding Document)
- MIL-STD-689 - Mobile Communications and Electronic Design Classes
- MIL-STD-704 - Aircraft Electric Power Characteristics
- MIL-STD-706 - Power Supply Voltages, Regulated, D.C. Within Electronic Equipment
- MIL-STD-736 - Unitized Equipment Design
- MIL-STD-743 - Cleaning and Protecting Piping for Hydraulic Power Transmission Equipment (Superseded by ms-419a)
- MIL-STD-752 - Equipment Spectrum Signatures, Collection Standard for (Use MIL-STD-449)
- MIL-STD-761 - Electric Power, Alternating Current for Shipboard Use, Characteristics and Utilization (Replaced by MIL-STD-1399)
- MIL-STD-767 - Control of Hardware Cleanliness - CONTROLLED: PLEASE CONTACT YOUR CONTRACTING OFFICER
- MIL-STD-768 - Instructions for Repair of Aircraft and Weapons Reinforced Plastic and Sandwich Structures, Part I, All Plastic Construction (Cancelled, No Replacement)
- MIL-STD-775 - X-Ray Standards for Welding Electrode Qualification and Quality Conformance Test Welds
- MIL-STD-778 - Maintainability Terms and Definitions (Superseded by MIL-STD-721B)
- MIL-STD-780 - Work Unit Codes for Aeronautical Equipment; Uniform Numbering System (No Superseding Document)
- MIL-STD-782 - Reconnaissance/Mapping Data Marking (No Superseding Document)
- MIL-STD-787 - Joint Optical Range Instrumentation Type Designation System (No Superseding Document)
- MIL-STD-788 - Test Requirements for Replenishment-at-Sea, Machinery and Equipment Installations, Tensioned Highline Stations With Electro-Hydraulic or Electro-Mechanical Drives (No Superseding Document)
- MIL-STD-789 - Contractor Technical Information Coding of Replenishment Parts
- MIL-STD-796 - Chemical Cleaning of Main and Auxiliary Boilers (Hydrochloric Acid Method
- MIL-STD-802 - Number, Aircraft Engines and Engine Cylinders, Combustion Chambers, Flame Tubes, Inner Liners, and Similar Items (No Superseding Document)
- MIL-STD-803 - Human Engineering Design Criteria for Aerospace Systems and Equipment (Part 1 Aerospace System Ground Equipment) (Superseded by MIL-STD-1472)
- MIL-STD-803/1 - Human Engineering Design Criteria for Aerospace Systems and Equipment (Part 1 Aerospace System Ground Equipment) (Superseded by MIL-STD-1472)
- MIL-STD-803/2 - Human Engineering Design Criteria for Aerospace Systems and Equipment Part 2. Aerospace Vehicles and Vehicle Equipment (Superseded by MIL-STD-1472)
- MIL-STD-803/3 - Human Engineering Design Criteria for Aerospace Systems and Equipment Part 3. Aerospace Vehicles and Vehicle Equipment (Superseded by MIL-STD-1472)
- MIL-STD-806 - Graphical Symbols for Logic Diagrams (Superseded by ANSI Y32.14-1973)
- MIL-STD-829 - Terms and Definitions for Maintainability (Use MIL-STD-778)
- MIL-STD-833 - Minimization of Hazards of Electromagnetic Radiation of Electroexplosive Devices (Superseded by MIL-STD-1512)
- MIL-STD-841 - Marking of Aircraft and Missile Propulsion System Parts Fabricated From Critical High Temperature Alloys (No Superseding Document)
- MIL-STD-842 - Uniform Procedures for Type Designation and Item Identification (Superseded by MIL-STD-1812)
- MIL-STD-847 - Format Requirements for Scientific and Technical Reports Prepared by or for the Department of Defense (Superseded by ANSI Z39.18)
- MIL-STD-859 - Standard Calibration Table for Aeronautical Pressure Measuring Equipment
- MIL-STD-864 - Support Equipment Functional Classification Categories (No Superseding Document)
- MIL-STD-875 - Type Designation System for Aeronautical and Support Equipment (Superseded by MIL-STD-1812)
- MIL-STD-880 - Abbreviations for Use on Airborne Equipment (Superseded by MIL-STD-738B)
- MIL-STD-881 - Work Breakdown Structures for Defense Materiel Items
- MIL-STD-885 - Procurement Data Packages (Superseded by DOD-D-100 and DI-E-7031)
- MIL-STD-890 - ENVIRONMENTAL CONTROL,ENVIRONMENTAL PROTECTION, and ENGINE AIR BLEED SUBSYSTEM PERFORMANCE and DESIGN REQUIREMENTS ANALYSES (SUPERSEDED BY MIL-E-87145)
- MIL-STD-891 - Contractor Parts Control and Standardization Program (Use MIL-STD-965)
- MIL-STD-963 - Data Item Descriptions (DIDs)
- MIL-STD-965 - Parts Control Program (Superseded by MIL-HDBK-965)
- MIL-T-11308 - Treatment and Painting (for Construction and Engineering Equipment) (Superseded by MIL-T-704)
- MIL-T-12522 - Thermograph ML-227-( )
- MIL-T-152 - Treatment, Moisture and Fungus-Resistant, of Communications, Electronic, and Associated Electrical Equipment
- MIL-T-18303 - Test Procedures; Preproduction, Acceptance, and Life for Aircraft Electronic Equipment, Format for
- MIL-T-21200 - Test Equipment for Use With Electronic and Electrical Equipment, General Specification For
- MIL-T-22703 - Technical Manual, Maintenance Instructions (for Surface-Launched Guided Missiles)
- MIL-T-23103 - Thermal Performance Evaluation, Airborne Electronic Equipment and Systems, General Requirement for (Superseded by MIL-STD-2218)
- MIL-T-2318 - Thermometer, Incubator
- MIL-T-23336 - Technical Directives (Letter Type) Preparation Of
- MIL-T-2391 - Trocar, Horse
- MIL-T-24309 - Technical Support Plan for Electronic Equipment (Superseded by MIL-STD-1369, MIL-STD-1388/1, and MIL-STD-1388/2)
- MIL-T-2542 - Tester, Hoof
- MIL-T-26673 - Test Program for Equipment, Contractor- Established
- MIL-T-3343 - Thermometer, Dairy
- MIL-T-55458 - The Army Equipment Record System (Taers), Forms and Data For
- MIL-T-82313 - Technical Publications Covering Training Devices (Superseded by MIL-M-82376)
- MIL-T-83696 - Technical Data, Explosives Hazard Classification, Development of (No Superseding Document)
- MIL-T-9107 - Test Reports, Preparation Of
- MIL-T-9887 - Technical Manuals. Commercial Technical Data (Missile-Space Systems)
- MIL-U-25900 - Uniform Design Criteria for Airborne Electronic Equipment
- MIL-V-24474 - Value Engineering Program Requirements (Naval Ship Systems Command) (No Superseding Document)
- MIL-V-38352 - Value Engineering Prog(Superseded by MIL-STD-1771)
- MIL-V-45201 - Value Analysis of Ordnance Equipment
- MIL-V-55051 - Value Engineering of Signal Corps Equipment (Use MIL-V-38352)
- MIL-W-12518 - Welding of Homogeneous Armor, Metal-Arc, Manual, With Ferritic Electrodes (Use MIL-W-46086 for Reference)
- MIL-W-13779 - Welding, Metal Arc, Steels, Constructional, Readily Weldable, for Low-Stressed Joints (Superseded by MIL-STD-1261)
- MIL-W-27076 - Workmanship Standards for Ground Electronic and Associated Equipment (Superseded by MIL-STD-454)
- MIL-W-82573 - Weapons System, or Ordnance System, Integrated Maintenance Requirements Plans (Imrps) Development and Preparation of (Use MIL-P-24534)
- MS-15031 - Socket, Deck (for Metal Furniture)
- MS-17794 - Criteria, Jet Electrical Starting System, Dc
- MS-25245 - Connections, Input Power Airborne Electronic Equipment, 28-Volt Dc, 115-Volt Single-Phase Ac, or 115/200 Volt 3-Phase Ac, or Combinations (Asg)
- MS-25494 - Tool, Manual, Hydraulic, for Crimping Electric Wire Terminals
- MS-25497 - Instrument, Pilot, Flight, Basic Standard Arrangement for Helicopters (Superseded by ms-33572)
- MS-27726 - Integrated Wire Termination System for Use on Electrical Components (Superseded by MIL-STD-1549)
- MS-28112 - Instrument, Basic Standard Arrangement for Fixed Wing Aircraft (No Superseding Document)
- MS-28911 - Turbine Engine Constant Current Starting System Wiring Diagram
- MS-33533 - Tolerances - Seamless Corrosion-Resistant Steel Tubing Round
- MS-33540 - Safety Wiring and Cotter Pinning, General Practices for (Superseded by NASM-33540)
- MS-33578 - Recesses, Cross, Low Torque Drive, Dimensions and Gage Dimensions for (Asg) (Use ms-9006)
- MS-33586 - Metal, Definition of and Protection for Dissimilar (Use MIL-STD-889)
- MS-35057 - Resistor, Fxd, Nonwire Wound (Accurate) (Type N15).
- MS-35253 - Support Ring
- MS-35718 - Connector, Receptacle (Bnc) RFUG-1098/U
- MS-35805 - Capacitor, Dry Dielectrolytic, Polarized, Style Ce33 (Use MIL-C-62/5a)
- MS-35806 - Capacitor, Dry Electrolytic, Polarized, Style Ce42 (Use MIL-C-62/7a)
- MS-90372 - Internal Thread Allowance Dimensions, Design Standard for (No Superseding Document)
- NAS-10001 - Preferred Metric Units for Aerospace
- NAS-3610 - Cargo Unit Load Devices - Specification For
- NAS-519 - Stylus - 100 Deg. Flat Head Gage
- NASM-33540 - Safety Wiring, Safety Cabling, Cotter Pinning, General Practices for
- NFPA-325A - Fire Protection Guide on Hazardous Materials (NFPA-325A-68325-M 1969, 49 1969, 491M 1968, 704M) - See NFPA-325
- O-C-104 - Calcium Chloride, Anhydrous, Technical Grade +Cancelled, Superseded by O-C-105
- QPL-13857 - Impregnation of Metal Castings
- QPL-5456 - Pump, Engine Driven, Air
- QPL-693 - Cement, Metallurgical, Air-Setting, High-Temperature
- QQ-A-451 - Aluminum Ingots +Cancelled, 1964, No S/S Document+
- QQ-C-400 - Copper-Base Alloy Centrifugal Castings+Superseded By QQ-C-390+
- QQ-M-161 - Metal, Antifriction, Castings and Ingots +Cancelled, 1952, No S/S Document+
- RR-P-101 - Pan, Pudding, Corrosion-Resisting-Steel (Cancelled, 1969, Use RR-P-54)
- SAWE-RP12 - Weight Control Technical Requirements for Surface Ships
- SAWE-RP13 - Surface Ships and Submarines, Reporting Mass Properties of, Standard Coordinate System F
- SAWE-RP14 - Weight Estimating and Margin Manual for Marine Vehicles
- SS-117110 - Corrosion of metals and alloys - Determination ofdezincification resistance of brass
- SS-117211 - Corrosion of metals and alloys - Corrosion tests in artificial atmosphere - Accelerated outdoor test by intermittent spraying of a salt solution (Scab test)
- SS-1192 - Fire fighting equipment - Portable fire extinguishers
- SS-1240 - Piping systems - Welding ends for components of unalloyed steel and low alloy wrought steel
- TT-C-607 - Conditioner, Exterior, for Free Chalking Masonry Surfaces +Cancelled, 1979, No S/S Doc
- UU-T-791 - Tubes, Map Storage +Cancelled, 1964, No S/S Document+
- W-L-131 - Lamp - Auxiliaries, Fluorescent (Cancelled, 4/30/56, Superseded by W-S-755 and W-B-30)
- W-U-546 - Units, Heating, Electric, Replacement (for Water Heaters, +Canc, Superseded By W-C-586+
- X-28863 - Destructor Systems, Minimum Requirement (Number Error - SEEX-28663, 21 Feb 57)
- ZZ-H-481 - Hose, Oil & Gasoline, Suction & Discharge, Synthetic-Rubber,(Canc, 1964, No S/S Docume
- ZZ-I-111 - Ice Bag, Helmet Shaped