Document Center List of Standards on Furniture Including Upholstery, Mattresses, Office Furniture, School Furniture, Etc.
ICS Code 97.140
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-C1503 - Standard Specification for Silvered Flat Glass Mirror
- ASTM-D3597 - Standard Performance Specification for Woven Upholstery Fabrics—Plain, Tufted, or Flocked
- ASTM-D3690 - Standard Performance Specification for Vinyl-Coated and Urethane-Coated Upholstery Fabrics—Indoor
- ASTM-D4033 - Standard Test Method for Resistance to Yarn Slippage at the Sewn Seam in Upholstery Fabrics (Dynamic Fatigue Method) (Withdrawn 2001)
- ASTM-D4034 - Standard Test Method for Resistance to Yarn Slippage at the Sewn Seam in Woven Upholstery Fabrics (Withdrawn 2001)
- ASTM-D4771 - Standard Performance Specification for Knitted Upholstery Fabrics for Indoor Furniture
- ASTM-D4852 - Standard Practice for Evaluation of Attached Upholstery Fabrics
- ASTM-D7016 - Standard Test Method to Evaluate Edge Binding Components Used in Mattresses After Exposure to An Open Flame
- ASTM-D7023 - Standard Terminology Relating to Home Furnishings
- ASTM-D8210 - Standard Test Method for Automatic Determination of Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants Using a Rotational Viscometer
- ASTM-E1352 - Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies (Withdrawn 2022)
- ASTM-E1353 - Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture (Withdrawn 2022)
- ASTM-E1474 - Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
- ASTM-E1537 - Standard Test Method for Fire Testing of Upholstered Furniture
- ASTM-E1590 - Standard Test Method for Fire Testing of Mattresses
- ASTM-E1822 - Standard Test Method for Fire Testing of Stacked Chairs
- ASTM-F1169 - Standard Consumer Safety Specification for Full-Size Baby Cribs
- ASTM-F1550 - Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter
- ASTM-F1561 - Standard Performance Requirements for Plastic Chairs for Outdoor Use
- ASTM-F1566 - Standard Test Methods for Evaluation of Innersprings, Boxsprings, Mattresses or Mattress Sets
- ASTM-F1838 - Standard Performance Requirements for Adult and Children’s Plastic Chairs for Outdoor Use
- ASTM-F1858 - Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use
- ASTM-F1870 - Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities
- ASTM-F1912 - Standard Specification for Safety of Bean Bag Chairs and Bean Bag Chair Covers
- ASTM-F1917 - Standard Consumer Safety Performance Specification for Infant Bedding and Related Accessories
- ASTM-F1967 - Standard Consumer Safety Specification for Infant Bath Seats
- ASTM-F1988 - Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use
- ASTM-F2057 - Standard Safety Specification for Clothing Storage Units
- ASTM-F2598 - Standard Consumer Safety Specification for Sealed Storage Chests such as Cedar Chests, Hope Chests, Blanket Chests, Keepsake Chests
- ASTM-F2613 - Standard Consumer Safety Specification for Children's Chairs and Stools
- ASTM-F2755 - Standard Safety Specification for Safety Labeling of Inflatable Air Mattresses
- ASTM-F2813 - Standard Specification for Glass Used as a Horizontal Surface in Desks and Tables
- ASTM-F2906 - Standard Consumer Safety Specification for Bedside Sleepers
- ASTM-F2933 - Standard Consumer Safety Specification for Crib Mattresses
- ASTM-F3096 - Standard Performance Specification for Tipover Restraint(s) Used with Clothing Storage Unit(s)
- ASTM-F404 - Standard Consumer Safety Specification for High Chairs
- ASTM-PS110 - Specification for Safety Specification for Chests, Door Chests, and Dressers (Withdrawn 2000)
- ASTM-PS55 - Performance Requirements for Multipositional Plastic Chairs, With Adjustable Backs or Reclining Mechanisms, for Outdoor Use (Withdrawn 1998)
- ASTM-PS84 - Specification for Bean Bag Chairs (Withdrawn 1998)
- ASTM-PS96 - Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, with Adjustable Backs, For Outdoor Use (Withdrawn 1999)
BSI:
- BS-1877-10 - Domestic bedding
- BS-2483 - Specification for overbed tables
- BS-2543 - Upholstery fabrics for end use applications. Classification
- BS-3044 - Guide to ergonomics principles in the design and selection of office furniture
- BS-3129 - Specification for latex foam rubber components for furniture
- BS-3173 - Specification for spring units for mattresses
- BS-3962-1 - Methods of test for finishes for wooden furniture.
- BS-3962-5 - Methods of test for finishes for wooden furniture
- BS-3962-6 - Methods of test for finishes for wooden furniture. Assessment of resistance to mechanical damage
- BS-4438 - Specification for filing cabinets and suspended filing pockets
- BS-4723 - Stretch covers for upholstered furniture. Specification
- BS-4875-1 - Strength and stability of furniture
- BS-4875-3 - Strength and stability of furniture. Methods for determination of strength of settees
- BS-4875-5 - Strength and stability of furniture. Methods for determination of strength of tables and trolleys
- BS-4875-6 - Strength and stability of furniture. Methods for determination of stability of tables and trolleys
- BS-4875-7 - Strength and stability of furniture
- BS-4875-8 - Furniture. Strength and stability of furniture. Methods for determination of stability of non-domestic storage furniture
- BS-4948 - Method for assessment of the visible soiling by body contact of upholstery fabrics
- BS-5127 - Specification for polyolefin webbing for divans and bed bases
- BS-5459-3 - Part 3: Storage Furniture, Performance Requirements & Tests for Office Furniture
- BS-5799 - Specification for safety requirements for children's high chairs and multi-purpose high chairs for domestic use
- BS-5799-1 - Children's high chairs and multi-purpose chairs for domestic use
- BS-5852 - Methods of test for assessment of the ignitability of upholstered seating by smouldering and flaming ignition sources
- BS-5852-1 - Fire tests for furniture
- BS-5852-2 - Fire tests for furniture
- BS-5873-3 - Specification for Strength and Stability of Tables for Educational Institutions
- BS-5873-4 - Educational furniture. Specification for strength and stability of storage furniture for educational institutions
- BS-5873-5 - Educational furniture
- BS-6261 - Method for evaluating the application of and interaction between components in upholstered furniture
- BS-6396 - Electrical systems in furniture. Specification
- BS-6608 - Specification for cattle hide leathers for upholstered furniture
- BS-6807 - Methods of test for assessment of ignitability of mattresses, upholstered divans and upholstered bed bases with flaming types of primary and secondary sources of ignition
- BS-6998 - Specification for bunk beds
- BS-7176 - Specification for resistance to ignition of upholstered furniture for non-domestic seating by testing composites
- BS-7177 - Specification for resistance to ignition of mattresses, mattress pads, divans and bed bases
- BS-7376 - Inclusion of glass in the construction of tables and trolleys for domestic use. Specification
- BS-7449 - Specification for inclusion of glass in the construction of furniture, other than tables or trolleys, including cabinets, shelving systems and wall hung or free standing mirrors
- BS-7558 - Specification for gun cabinets
- BS-7945 - Non-domestic furniture. Seating. Determination of stability
- BS-826 - Specification for steel single tier bolted shelving (angle upright type)
- BS-8474 - Furniture. Chairs with electrically operated support surfaces. Requirements
- BS-8480 - Medical devices. Chairs with electrically operated support surfaces. Requirements
- BS-8509 - Childrens beds for domestic use. Safety requirements and test methods
- BS-8510 - Child use and care articles. Safety of children's sleep bags. Safety requirements and test methods
- BS-EN-1021-1 - Furniture. Assessment of the ignitability of upholstered furniture
- BS-EN-1021-2 - Furniture. Assessment of the ignitability of upholstered furniture
- BS-EN-1022 - Furniture. Seating. Determination of stability
- BS-EN-1022-TC - Tracked Changes. Furniture. Seating. Determination of stability
- BS-EN-1023-1 - Office furniture. Screens
- BS-EN-1023-2 - Office furniture. Screens
- BS-EN-1023-3 - Office furniture. Screens
- BS-EN-1130 - Children's furniture. Cribs. Safety requirements and test methods
- BS-EN-12227-1 - Part 1: Safety Requirements
- BS-EN-12227-2 - Part 2: Test Methods
- BS-EN-12520 - Furniture. Strength, durability and safety. Requirements for domestic seating
- BS-EN-12520-TC - Tracked Changes. Furniture. Strength, durability and safety. Requirements for domestic seating
- BS-EN-12521 - Furniture. Safety, strength and durability. Requirements for domestic tables
- BS-EN-12521-TC - Tracked Changes. Furniture. Safety, strength and durability. Requirements for domestic tables
- BS-EN-1272 - Child care articles. Table mounted chairs. Safety requirements and test methods
- BS-EN-12720 - Furniture. Assessment of surface resistance to cold liquids
- BS-EN-12721 - Furniture. Assessment of surface resistance to wet heat
- BS-EN-12722 - Furniture. Assessment of surface resistance to dry heat
- BS-EN-12727 - Furniture. Ranked seating. Requirements for safety, strength and durability
- BS-EN-12727-TC - Tracked Changes. Furniture. Ranked seating. Requirements for safety, strength and durability
- BS-EN-1272-TC - Tracked Changes. Child care articles. Table mounted chairs. Safety requirements and test methods
- BS-EN-12951 - Prefabricated accessories for roofing. Permanently fixed roof ladders. Product specification and test methods
- BS-EN-13336 - Leather. Upholstery leather characteristics. Guide for selection of leather for furniture
- BS-EN-13336-TC - Tracked Changes. Leather. Upholstery leather characteristics. Guide for selection of leather for furniture
- BS-EN-1335-2 - Office furniture. Office work chair
- BS-EN-1335-3 - Office furniture. Office work chair. Test methods
- BS-EN-13453-1 - Furniture. Bunk beds and high beds for non-domestic use. Safety, strength and durability requirements
- BS-EN-13453-2 - Bunk beds and high beds for non-domestic use
- BS-EN-13721 - Furniture. Assessment of the surface reflectance
- BS-EN-13721-TC - Tracked Changes. Furniture. Assessment of the surface reflectance
- BS-EN-13722 - Furniture. Assessment of the surface gloss
- BS-EN-13759 - Furniture. Operating mechanisms for seating and sofa-beds. Test methods
- BS-EN-13761 - Office furniture. Visitors chairs
- BS-EN-14073-2 - Office furniture. Storage furniture
- BS-EN-14073-3 - Office furniture. Storage furniture
- BS-EN-14074 - Office furniture. Tables and desks and storage furniture. Test methods for the determination of strength and durability of moving parts
- BS-EN-14434 - Writing boards for educational institutions. Ergonomic, technical and safety requirements and their test methods
- BS-EN-14703 - Furniture. Links for non-domestic seating linked together in a row. Strength requirements and test methods
- BS-EN-14749 - Furniture. Domestic and kitchen storage units and kitchen-worktops. Safety requirements and test methods
- BS-EN-14988 - Children's high chairs. Requirements and test methods
- BS-EN-14988-1 - Children's high chairs
- BS-EN-14988-2 - Children's high chairs
- BS-EN-15185-TC - Tracked Changes. Furniture. Assessment of the surface resistance to abrasion
- BS-EN-15186 - Furniture. Assessment of the surface resistance to scratching
- BS-EN-15186-TC - Tracked Changes. Furniture. Assessment of the surface resistance to scratching
- BS-EN-15187 - Furniture. Assessment of the effect of light exposure
- BS-EN-15338 - Hardware for furniture. Strength and durability of extension elements and their components
- BS-EN-15372 - Furniture. Strength, durability and safety. Requirements for non-domestic tables
- BS-EN-15372-TC - Tracked Changes. Furniture. Strength, durability and safety. Requirements for non-domestic tables
- BS-EN-15373 - Furniture. Strength, durability and safety. Requirements for non-domestic seating
- BS-EN-15618 - Rubber- or plastic-coated fabrics. Upholstery fabrics. Classification and methods of test
- BS-EN-15618-TC - Tracked Changes. Rubber- or plastic-coated fabrics. Upholstery fabrics. Classification and methods of test
- BS-EN-15706 - Hardware for furniture. Strength and durability of slide fittings for sliding doors and roll fronts
- BS-EN-15939 - Hardware for furniture. Strength and loading capacity of wall attachment devices
- BS-EN-16014 - Hardware for furniture. Strength and durability of locking mechanisms
- BS-EN-16120 - Child use and care articles. Chair mounted seat
- BS-EN-16121 - Non-domestic storage furniture. Requirements for safety, strength, durability and stability
- BS-EN-16122 - Domestic and non-domestic storage furniture. Test methods for the determination of strength, durability and stability
- BS-EN-16139 - Furniture. Strength, durability and safety. Requirements for non-domestic seating
- BS-EN-16337 - Hardware for furniture. Strength and loading capacity of shelf supports
- BS-EN-16611 - Furniture. Assessment of the surface resistance to microscratching
- BS-EN-16611-TC - Tracked Changes. Furniture. Assessment of the surface resistance to microscratching
- BS-EN-16780 - Textile child care articles. Safety requirements and test methods for children's cot bumpers
- BS-EN-16890 - Children's furniture. Mattresses for cots and cribs. Safety requirements and test methods
- BS-EN-16948 - Child protective products. Consumer fitted child resistant locking devices for cupboards and drawers. Safety requirements and test methods
- BS-EN-16955 - Hardware for furniture. Tapered pressure tubes for self-supporting gas springs for the height adjustment of seating. Test methods and requirements for strength and durability
- BS-EN-17191 - Childrens Furniture. Seating for children. Safety requirements and test methods
- BS-EN-17214 - Visual assessment of furniture surfaces
- BS-EN-1725-TC - Tracked Changes. Furniture. Beds. Requirements for safety, strength and durability
- BS-EN-1727 - Domestic furniture. Storage furniture. Safety requirements and test methods
- BS-EN-1728 - Furniture. Seating. Test methods for the determination of strength and durability
- BS-EN-1729-1 - Furniture. Chairs and tables for educational institutions
- BS-EN-1729-2 - Furniture. Chairs and tables for educational institutions
- BS-EN-1729-2-TC - Tracked Changes. Furniture. Chairs and tables for educational institutions
- BS-EN-1730 - Furniture. Tables. Test methods for the determination of stability, strength and durability
- BS-EN-17869 - Hardware for furniture. Test methods for strength and overload tests of connectors for furniture constructed from panel material
- BS-EN-17902 - Furniture. Circularity. Evaluation method for dis/re-assembly capability
- BS-EN-1957 - Furniture. Beds and mattresses. Test methods for the determination of functional characteristics and assessment criteria
- BS-EN-527-1 - Office furniture. Work tables and desks
- BS-EN-527-2 - Office furniture. Work tables
- BS-EN-527-2-TC - Office furniture. Work tables
- BS-EN-581-1 - Outdoor furniture. Seating and tables for camping, domestic and contract use
- BS-EN-581-2 - Outdoor furniture. Seating and tables for camping, domestic and contract use
- BS-EN-581-3 - Outdoor furniture. Seating and tables for camping, domestic and contract use
- BS-EN-581-3-TC - Tracked Changes. Outdoor furniture. Seating and tables for camping, domestic and contract use
- BS-EN-597-1 - Furniture. Assessment of the ignitability of mattresses and upholstered bed bases
- BS-EN-597-2 - Furniture. Assessment of the ignitability of mattresses and upholstered bed bases
- BS-EN-716-1 - Furniture. Children's cots and folding cots for domestic use
- BS-EN-716-2 - Furniture. Children's cots and folding cots for domestic use
- BS-EN-747-1 - Furniture. Bunk beds and high beds
- BS-EN-747-1-TC - Tracked Changes. Furniture. Bunk beds and high beds
- BS-EN-747-2 - Furniture. Bunk beds and high beds
- BS-EN-747-2-TC - Tracked Changes. Furniture. Bunk beds and high beds
- BS-EN-IEC-60335-2-111 - Household and similar electrical appliances. Safety
- BS-ISO-12808 - Hardware for furniture. Strength and durability of extension elements and their components
- BS-ISO-16131 - Leather. Upholstery leather characteristics. Selection of leather for furniture
- BS-ISO-16502-1 - Furniture. Assessment of the ignitability of mattresses and upholstered bed bases
- BS-ISO-16502-2 - Furniture. Assessment of the ignitability of mattresses and upholstered bed bases
- BS-ISO-19682 - Furniture. Tables. Test methods for the determination of stability, strength and durability
- BS-ISO-21015 - Office furniture. Office work chairs. Test methods for the determination of stability, strength and durability
- BS-ISO-21016 - Office furniture. Tables and desks. Test methods for the determination of stability, strength and durability
- BS-ISO-22879 - Castors and wheels. Requirements for castors for furniture
- BS-ISO-22880 - Castors and wheels. Requirements for castors for swivel chairs
- BS-ISO-23767 - Childrens furniture. Mattresses for cots and cribs. Safety requirements and test methods
- BS-ISO-23769 - Furniture. Mattresses. Test methods for the determination of functional characteristics
- BS-ISO-24496 - Office furniture. Office chairs. Methods for the determination of dimensions
- BS-ISO-4211-2 - Furniture. Tests for surface finishes
- BS-ISO-4211-3 - Furniture. Tests for surface finishes
- BS-ISO-4211-5 - Furniture. Tests for surface finishes
- BS-ISO-4769 - Hardware for furniture. Strength and durability of hinges and their components. Hinges pivoting on a vertical axis
- BS-ISO-6128 - Laminated products made of bamboo strips for indoor furniture purposes. Requirements and test methods
- BS-ISO-7170 - Furniture. Storage units. Test methods for the determination of strength, durability and stability
- BS-ISO-7171 - Furniture. Storage units. Test methods for the determination of stability
- BS-ISO-7173 - Furniture. Chairs and stools. Determination of strength and durability
- BS-ISO-7617-1-TC - Tracked Changes. Plastics-coated fabrics for upholstery
- BS-ISO-9098-1 - Bunk beds and high beds. Safety requirements and tests
- BS-ISO-9098-2 - Bunk beds and high beds. Safety requirements and tests
- CWA-14515 - Model of Different Categories of Furniture & Types of Products Created To Build a Port
- DD-CEN-15185 - Furniture. Assessment of the surface resistance to abrasion
- DD-CEN-15186 - Furniture. Assessment of the surface resistance to scratching
- DD-ENV-1178-1 - Furniture. Children's high chairs for domestic use. Safety requirements
- DD-ENV-1178-2 - Furniture. Children's high chairs for domestic use
- DD-ENV-12520 - Domestic furniture. Seating. Mechanical and structural safety requirements
- DD-ENV-12521 - Domestic furniture. Tables. Mechanical and structural safety requirements
- DD-ENV-13759 - Domestic furniture. Seating. Test method for the determination of the durability of reclining and/or tilting mechanisms and operating mechanisms for convertible sofa beds
- DD-ENV-14443 - Domestic furniture. Seating. Test methods for the determination of durability of upholstery
- DD-ENV-581-2 - Outdoor furniture. Seating and tables for camping, domestic and contract use
- PD-CEN-1335-4 - Office furniture. Office work chair
- PD-CEN-14073-1 - Office furniture. Storage furniture
- PD-CEN-14699 - Office Furniture. Terminology
- PD-CEN-15349 - Hardware for furniture. Terms for extension elements and their components
- PD-CEN-15588 - Hardware for furniture. Terms for hinges and their components
- PD-CEN-15709 - Hardware for furniture. Terms for slide fittings for sliding doors and roll fronts
- PD-CEN-16015 - Hardware for furniture. Terms for locking mechanisms
- PD-CEN-16209 - Furniture. Classification for properties for furniture surfaces
- PD-CEN-16611 - Furniture. Assessment of the surface resistance to microscratching
- PD-CEN-16611-TC - Tracked Changes. Furniture. Assessment of the surface resistance to microscratching
- PD-CEN-17202 - Furniture. General safety guidelines. Entrapment of fingers
- PD-CEN-17292 - Technical report regarding precision data for standards EN 12720, EN 12721, EN 12722, EN 15185 and EN 15186
- PD-CEN-17538 - Furniture. Common test equipment. Test foams and mattresses
- PD-ISO-24496 - Office furniture. Office work chairs. Methods for the determination of dimensions
IEC:
- IEC-60335-2-111 - Household and similar electrical appliances - Safety - Part 2-111: Particular requirements for electric ondol mattress with a non-flexible heated part
- IEC-60335-2-111-EXV - Household and similar electrical appliances - Safety - Part 2-111: Particular requirements for electric ondol mattress with a non-flexible heated part
- IEC-60335-2-116 - Household and similar electrical appliances - Safety - Part 2-116: Particular requirements for furniture with electrically motorized parts
ISO:
- ISO-10131-1 - Foldaway beds -- Safety requirements and tests -- Part 1: Safety requirements
- ISO-10131-2 - Foldaway beds -- Safety requirements and tests -- Part 2: Test methods
- ISO-12808 - Hardware for furniture - Strength and durability of extension elements and their components
- ISO-16131 - Leather - Upholstery leather characteristics - Selection of leather for furniture
- ISO-19682 - Furniture - Tables - Test methods for the determination of stability, strength and durability
- ISO-19833 - Furniture - Beds - Test methods for the determination of stability, strength and durability
- ISO-21015 - Office furniture - Office work chairs - Test methods for the determination of stability, strength and durability
- ISO-21016 - Office furniture - Tables and desks - Test methods for the determination of stability, strength and durability
- ISO-22878 - Castors and wheels - Test methods and apparatus
- ISO-22879 - Castors and wheels - Requirements for castors for furniture
- ISO-22880 - Castors and wheels - Requirements for castors for swivel chairs
- ISO-23767 - Children.s furniture - Mattresses for cots and cribs - Safety requirements and test methods
- ISO-23769 - Furniture - Mattresses - Test methods for the determination of functional characteristics
- ISO-24496 - Office furniture - Office chairs - Methods for the determination of dimensions
- ISO-4211 - Furniture -- Assessment of surface resistance to cold liquids
- ISO-4211-2 - Furniture - Tests for surface finishes - Part 2: Assessment of resistance to wet heat
- ISO-4211-3 - Furniture - Tests for surface finishes - Part 3: Assessment of resistance to dry heat
- ISO-4211-4 - Furniture -- Tests for surfaces -- Part 4: Assessment of resistance to impact
- ISO-4211-5 - Furniture - Tests for surface finishes - Part 5: Assessment of resistance to abrasion
- ISO-4769 - Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis
- ISO-5970 - Furniture -- Chairs and tables for educational institutions -- Functional sizes
- ISO-6128 - Laminated products made of bamboo strips for indoor furniture purposes - Requirements and test methods
- ISO-7170 - Furniture - Storage units - Test methods for the determination of strength, durability and stability
- ISO-7171 - Furniture - Storage units - Test methods for the determination of stability
- ISO-7173 - Furniture - Chairs and stools - Determination of strength and durability
- ISO-7174-1 - Furniture -- Chairs -- Determination of stability -- Part 1: Upright chairs and stools
- ISO-7174-2 - Furniture -- Chairs -- Determination of stability -- Part 2: Chairs with tilting or reclining mechanisms when fully reclined, and rocking chairs
- ISO-7175-1 - Furniture - Childrens cots and folding cots for domestic use - Part 1: Safety requirements
- ISO-7175-2 - Furniture - Childrens cots and folding cots for domestic use - Part 2: Test methods
- ISO-7617-1 - Plastics-coated fabrics for upholstery - Part 1: Specification for PVC-coated knitted fabrics
- ISO-7617-2 - Plastics-coated fabrics for upholstery -- Part 2: Specification for PVC-coated woven fabrics
- ISO-7617-3 - Plastics-coated fabrics for upholstery -- Part 3: Specification for polyurethane-coated woven fabrics
- ISO-8191-1 - Furniture - Assessment of the ignitability of upholstered furniture - Part 1 : Ignition source : smouldering cigarette
- ISO-8191-2 - Furniture - Assessment of ignitability of upholstered furniture - Part 2 : Ignition source : match-flame equivalent
- ISO-8555-1 - Hardware for furniture -- Terms for furniture fittings -- Part 1: Assembly fittings
- ISO-8555-2 - Hardware for furniture -- Terms for furniture fittings -- Part 2: Hinges and flap hinges
- ISO-8555-3 - Hardware for furniture -- Terms for furniture fittings -- Part 3: Drawer slides and sliding door gears
- ISO-8555-4 - Hardware for furniture -- Terms for furniture fittings -- Part 4: Holding devices, flap stays, lid stays
- ISO-8555-5 - Hardware for furniture -- Terms for furniture fittings -- Part 5: Height adjusters, furniture legs, underframes
- ISO-8555-6 - Hardware for furniture -- Terms for furniture fittings -- Part 6: Shelf supports, hanging rails, cabinet suspension brackets
- ISO-8555-7 - Hardware for furniture -- Terms for furniture fittings -- Part 7: Handles, knobs, escutcheons, escutcheon insets
- ISO-8555-8 - Hardware for furniture -- Terms for furniture fittings -- Part 8: Castors and glides
- ISO-9098-1 - Bunk beds and high beds - Safety requirements and tests - Part 1: Safety requirements
- ISO-9098-2 - Bunk beds and high beds - Safety requirements and tests - Part 2: Test methods
- ISO-9221-1 - Furniture - Childrens high chairs - Part 1: Safety requirements
- ISO-9221-2 - Furniture - Childrens high chairs - Part 2: Test methods
Other SDOs:
- DIN-EN-1021-1 - Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source smouldering cigarette; German version EN 1021-1:2014
- DIN-EN-1021-2 - Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source match flame equivalent; German version EN 1021-2:2014
- DIN-EN-1022 - Domestic furniture - Seating - Determination of stability; German version EN 1022:2005
- DIN-EN-13453-1 - Furniture - Bunk beds and high beds for non-domestic use - Part 1: Safety, strength and durability requirements; German version EN 13453-1:2004
- DIN-EN-13453-2 - Furniture - Bunk beds and high beds for non-domestic use - Part 2: Test methods; German version EN 13453-2:2004
- DIN-EN-13721 - Furniture, Assessment of the Surface Reflectance
- DIN-EN-13722 - Furniture, Assessment of the Surface Gloss
- DIN-EN-13761 - Office furniture - Visitors chairs; German version EN 13761:2002
- DIN-EN-14073-2 - Part 2: Safety Requirements, Office Furniture, Storage Furniture
- DIN-EN-14073-3 - Part 3: Test Methods for the Determination of Stability & Strength of the Structure, O
- DIN-EN-14074 - Office Furniture, Tables & Desks & Storage Furniture, Test Methods for the Determinati
- DIN-EN-14434 - Writing Boards for Educational Institutions - Ergonomic, Technical & Safety Requiremen
- DIN-EN-14465 - Textiles - Upholstery Fabrics - Specification & Methods of Test
- DIN-EN-14749 - Furniture - Domestic and kitchen storage units and kitchen-worktops - Safety requirements and test methods; German version EN 14749:2016
- DIN-EN-14988-1 - Children's high chairs - Part 1: Safety requirements; German version EN 14988-1:2006+A1:2012
- DIN-EN-14988-2 - Children's high chairs - Part 2: Test methods; German version EN 14988-2:2006+A1:2012
- DIN-EN-15187 - Furniture - Assessment of the Effect of Light Exposure
- DIN-EN-15338 - Hardware for Furniture - Strength & Durability of Extension Elements & Their Componen
- DIN-EN-1728 - Furniture - Seating - Test methods for the determination of strength and durability; German version EN 1728:2012 + AC:2013
- DIN-EN-1729-1 - Furniture - Chairs and tables for educational institutions - Part 1: Functional dimensions; German version EN 1729-1:2015
- DIN-EN-1729-2 - Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods; German version EN 1729-2:2012+A1:2015
- DIN-EN-1970 - Adjustable beds for disabled persons - Requirements and test methods; German version EN 1970:2000 + A1:2005
- DIN-EN-527-2 - Office furniture - Work tables - Part 2: Safety, strength and durability requirements; German version EN 527-2:2016
- DIN-EN-527-3 - Part 3: Methods of Test for the Determination of the Stability and the Mechanical Streng
- DIN-EN-581-1 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 1: General safety requirements; German version EN 581-1:2017
- DIN-ISO-7170 - Furniture - Storage Units - Determination of Strength & Durability
- EN-1021-1 - Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source smouldering cigarette
- EN-1021-2 - Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source match flame equivalent
- EN-1022 - Domestic Furniture - Seating - Determination of Stability
- EN-1023-1 - Office furniture - Screens - Part 1: Dimensions
- EN-12520 - Furniture - Strength, durability and safety - Requirements for domestic seating
- EN-12521 - Furniture - Strength, durability and safety - Requirements for domestic tables
- EN-1272 - Child care articles - Table mounted chairs - Safety requirements and test methods
- EN-12720 - Furniture - Assessment of surface resistance to cold liquids
- EN-12721 - Furniture - Assessment of surface resistance to wet heat
- EN-12722 - Furniture - Assessment of surface resistance to dry heat
- EN-12727 - Furniture - Ranked seating - Requirements for safety, strength and durability
- EN-12951 - Prefabricated Accessories for Roofing, Permanently Fixed Roof Ladders, Product Specifi
- EN-1335-2 - Part 2: Safety Requirements, Office Furniture - Office Work Chair
- EN-1335-3 - Part 3: Test Methods, Office Furniture - Office Work Chair
- EN-13453-1 - Part 1: Safety, Strength & Durability Requirements, Furniture, Bunk Beds & High Beds F
- EN-13453-2 - Part 2: Test Methods, Furniture, Bunk Beds & High Beds for Non-Domestic Use
- EN-13721 - Furniture, Assessment of the Surface Reflectance
- EN-13722 - Furniture, Assessment of the Surface Gloss
- EN-13759 - Furniture - Operating mechanisms for seating and sofa-beds - Test methods
- EN-13761 - Office furniture. Visitors chairs
- EN-14073-2 - Part 2: Safety Requirements, Office Furniture, Storage Furniture
- EN-14073-3 - Part 3: Test Methods for the Determination of Stability & Strength of the Structure, O
- EN-14074 - Office Furniture, Tables & Desks & Storage Furniture, Test Methods for the Determinati
- EN-14434 - Writing Boards for Educational Institutions - Ergonomic, Technical & Safety Requiremen
- EN-14703 - Furniture, Links for Non-Domestic Seating Linked Together in a Row, Strength Requireme
- EN-14749 - Furniture - Domestic and kitchen storage units and kitchen-worktops - Safety requirements and test methods
- EN-14988 - Children's high chairs - Requirements and test methods
- EN-14988-1 - Children's high chairs - Part 1: Safety requirements
- EN-14988-2 - Children's High Chairs, Test Methods
- EN-15185 - Furniture - Assessment of the surface resistance to abrasion
- EN-15186 - Furniture - Assessment of the surface resistance to scratching
- EN-15187 - Furniture - Assessment of the Effect of Light Exposure
- EN-15338 - Hardware for Furniture - Strength & Durability of Extension Elements & Their Componen
- EN-15372 - Furniture - Strength, durability and safety - Requirements for non-domestic tables
- EN-15373 - Furniture, Strength, Durability & Safety, Requirements for Non-Domestic Seating
- EN-15618 - Rubber- or plastic-coated fabrics - Upholstery fabrics - Classification and methods of test
- EN-15706 - Hardware for Furniture - Strength & Durability of Slide Fittings for Sliding Doors & R
- EN-15939 - Hardware for furniture - Strength and loading capacity of wall attachment devices
- EN-16014 - Hardware for furniture - Strength and durability of locking mechanisms
- EN-16120 - Child use and care articles - Chair mounted seat
- EN-16121 - Non-domestic storage furniture - Requirements for safety, strength, durability and stability
- EN-16122 - Domestic and non-domestic storage furniture - Test methods for the determination of strength, durability and stability
- EN-16139 - Furniture - Strength, durability and safety - Requirements for non-domestic seating
- EN-16337 - Hardware for furniture - Strength and loading capacity of shelf supports
- EN-16780 - Textile child care articles - Safety requirements and test methods for children's cot bumpers
- EN-16890 - Children's furniture - Mattresses for cots and cribs - Safety requirements and test methods
- EN-17214 - Visual assessment of furniture surfaces
- EN-1728 - Furniture - Seating - Test methods for the determination of strength and durability
- EN-1729-1 - Furniture - Chairs and tables for educational institutions - Part 1: Functional dimensions
- EN-1729-2 - Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods
- EN-1730 - Furniture - Tables - Test methods for the determination of stability, strength and durability
- EN-1957 - Furniture - Beds and mattresses - Test methods for the determination of functional characteristics and assessment criteria
- EN-1970 - Adjustable Beds for Disabled Persons, Requirements & Test Methods
- EN-527-1 - Office furniture - Work tables and desks - Part 1: Dimensions
- EN-527-2 - Office furniture - Work tables - Part 2: Safety, strength and durability requirements
- EN-581-1 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 1: General safety requirements
- EN-581-2 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 2: Mechanical safety requirements and test methods for seating
- EN-581-3 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 3: Mechanical safety requirements for tables
- EN-597-1 - Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 1: Ignition source smouldering cigarette
- EN-597-2 - Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 2: Ignition source: match flame equivalent
- EN-716-1 - Furniture - Children's cots and folding cots for domestic use - Part 1: Safety requirements
- EN-716-2 - Furniture - Children's cots and folding cots for domestic use - Part 2: Test methods
- EN-747-1 - Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements
- EN-747-2 - Furniture - Bunk beds and high beds - Part 2: Test methods
- JIS-S-1016 - Fixed desk and chair for lecture room
- SIS-CEN/TR-1335-4 - Office furniture - Office work chair - Part 4: Clarificaitons to EN 1335-1:2000 (Dimensions)
- SIS-CEN/TR-14073-1 - Office furniture - Storage furniture - Part 1: Dimensions
- SIS-CEN/TR-14699 - Office furniture - Terminology
- SIS-CEN/TR-15349 - Hardware for furniture - Terms for extension elements and their components
- SIS-CEN/TR-15588 - Hardware for furniture - Terms for hinges and their components
- SIS-CEN/TR-15709 - Hardware for furniture -Terms of slide fittings for sliding doors and roll fronts
- SIS-CEN/TR-16015 - Hardware for furniture - Terms for locking mechanisms
- SIS-CEN/TR-17202 - Furniture - General safety guidelines - Entrapment of fingers
- SIS-CEN/TR-17292 - Technical report regarding precision data for standards EN 12720, EN 12721, EN 12722, EN 15185 and EN 15186
- SIS-CEN/TS-15185 - Furniture - Assessment of the surface resistance to abrasion
- SIS-CEN/TS-15186 - Furniture - Assessment of the surface resistance to scratching
- SIS-CEN/TS-16209 - Furniture - Classification for properties for furniture surfaces
- SIS-CEN/TS-16611 - Furniture - Assessment of the surface resistance to microscratching
- SS-251250 - Upholstery fabrics - Tests for colour fastness - Colour fastness to water spotting
- SS-839140 - Determination of functional dimensions of furniture seating (including wheelchairs)
- SS-EN-1021-1 - Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source smouldering cigarette
- SS-EN-1021-2 - Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source match flame equivalent
- SS-EN-1022 - Furniture - Seating - Determination of stability
- SS-EN-1023-1 - Office furniture - Screens - Part 1: Dimensions
- SS-EN-1023-2 - Office furniture - Screens - Part 2: Mechanical safety requirements
- SS-EN-1023-3 - Office furniture - Screens - Part 3: Test methods
- SS-EN-1129-1 - Furniture - Foldaway beds - Safety requirements and testing - Part 1: Safety requirements
- SS-EN-1129-2 - Furniture - Foldaway beds - Safety requirements and testing - Part 2: Test methods
- SS-EN-1130 - Children's furniture - Cribs - Safety requirements and test methods
- SS-EN-1130-1 - Furniture - Cribs and cradles for domestic use - Part 1: Safety requirements
- SS-EN-1130-2 - Furniture - Cribs and cradles for domestic use - Part 2: Test methods
- SS-EN-12227 - Playpens for domestic use - Safety requirements and test methods
- SS-EN-12520 - Furniture - Strength, durability and safety - Requirements for domestic seating
- SS-EN-12521 - Furniture - Safety, strength and durability - Requirements for domestic tables
- SS-EN-12526 - Castors and wheels - Vocabulary, recommended symbols and multilingual dictionary
- SS-EN-12529 - Castors and wheels - Castors for furniture - Castors for swivel chairs - Requirements
- SS-EN-12530 - Castors and wheels - Castors and wheels for manually propelled institutional applications
- SS-EN-1272 - Child care articles - Table mounted chairs - Safety requirements and test methods
- SS-EN-12720 - Furniture - Assessment of surface resistance to cold liquids
- SS-EN-12721 - Furniture - Assessment of surface resistance to wet heat
- SS-EN-12722 - Furniture - Assessment of surface resistance to dry heat
- SS-EN-12727 - Furniture - Ranked seating - Requirements for safety, strength and durability
- SS-EN-12951 - Prefabricated accessories for roofing - Permanently fixed roof ladders - Product specification and test methods
- SS-EN-13336 - Leather - Upholstery leather characteristics - Guide for selection of leather for furniture
- SS-EN-1334 - Domestic furniture - Beds and mattresses - Methods of measurement and recommended tolerances
- SS-EN-1335-1 - Office furniture - Office work chair - Part 1: Dimensions - Determination of dimensions
- SS-EN-1335-2 - Office furniture - Office work chair - Part 2: Safety requirements
- SS-EN-1335-3 - Office furniture - Office work chair - Part 3: Test methods
- SS-EN-13453-1 - Furniture - Bunk beds and high beds for non-domestic use - Part 1: Safety, strength and durability requirements
- SS-EN-13453-2 - Furniture - Bunk beds and high beds for non-domestic use - Part 2: Test methods
- SS-EN-13480 - Metallic industrial piping
- SS-EN-13721 - Furniture - Assessment of the surface reflectance
- SS-EN-13722 - Furniture - Assessment of the surface gloss
- SS-EN-13759 - Furniture - Operating mechanisms for seating and sofa-beds - Test methods
- SS-EN-13761 - Office furniture - Visitors chairs
- SS-EN-13854 - Manufactured articles solely filled with feather and down - Requirements for upholstered parts and cushions
- SS-EN-13855-1 - Manufactured articles solely filled with feathers and down - Measurement of thickness and compressibility of cushions - Part 1: Test method by rotation
- SS-EN-13855-2 - Manufactured articles solely filled with feathers and down - Measurement of thickness and compressibility of cushions - Part 2: Test method by oscillation
- SS-EN-14072 - Glass in furniture - Test methods
- SS-EN-14073-2 - Office furniture - Storage furniture - Part 2: Safety requirements
- SS-EN-14073-3 - Office furniture - Storage furniture - Part 3: Test methods for the determination of stability and strength of the structure
- SS-EN-14074 - Office furniture - Tables and desks and storage furniture - Test methods for the determination of strength and durability of moving parts
- SS-EN-14434 - Writing boards for educational institutions - Ergonomic, technical and safety requirements and their test methods
- SS-EN-14465 - Textiles - Upholstery fabrics - Specification and methods of test
- SS-EN-14465-AM1 - Textiles - Upholstery fabrics - Specification and methods of test
- SS-EN-14703 - Furniture - Links for non-domestic seating linked together in a row - Strength requirements and test methods
- SS-EN-14727 - Laboratory furniture - Storage units for laboratories - Requirements and test methods
- SS-EN-14749 - Furniture - Domestic and kitchen storage units and kitchen-worktops - Safety requirements and test methods
- SS-EN-14988 - Children's high chairs - Requirements and test methods
- SS-EN-14988-1 - Children's high chairs - Part 1: Safety requirements
- SS-EN-14988-2 - Children's high chairs - Part 2: Test methods
- SS-EN-15185 - Furniture - Assessment of the surface resistance to abrasion
- SS-EN-15186 - Furniture - Assessment of the surface resistance to scratching
- SS-EN-15187 - Furniture - Assessment of the effect of light exposure
- SS-EN-15338 - Hardware for furniture - Strength and durability of extension elements and their components
- SS-EN-15372 - Furniture - Strength, durability and safety - Requirements for non-domestic tables
- SS-EN-15373 - Furniture - Strength, durability and safety - Requirements for non-domestic seating
- SS-EN-15570 - Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis
- SS-EN-15618 - Rubber- or plastic-coated fabrics - Upholstery fabrics - Classification and methods of test
- SS-EN-15706 - Hardware for furniture - Strength and durability of slide fittings for sliding doors and roll fronts
- SS-EN-15828 - Hardware for furniture - Strength and durability of hinges and their components - Stays and hinges pivoting on a horizontal axis
- SS-EN-15939 - Hardware for furniture - Strength and loading capacity of wall attachment devices
- SS-EN-16014 - Hardware for furniture - Strength and durability of locking mechanisms
- SS-EN-16120 - Child use and care articles - Chair mounted seat
- SS-EN-16121 - Non-domestic storage furniture - Requirements for safety, strength, durability and stability
- SS-EN-16122 - Domestic and non-domestic storage furniture - Test methods for the determination of strength, durability and stability
- SS-EN-16139 - Furniture - Strength, durability and safety - Requirements for non-domestic seating
- SS-EN-16223 - Leather - Requirements for the designation and description of leather in upholstery and automotive interior applications
- SS-EN-16223-1 - Leather - Requirements for the designation and description of leather in upholstery and automotive interior applications - Part 1: Upholstery applications
- SS-EN-16223-2 - Leather - Requirements for the designation and description of leather in upholstery and automotive interior applications - Part 2: Automotive interior applications
- SS-EN-16337 - Hardware for furniture - Strength and loading capacity of shelf supports
- SS-EN-16780 - Textile child care articles - Safety requirements and test methods for children's cot bumpers
- SS-EN-16890 - Children's furniture - Mattresses for cots and cribs - Safety requirements and test methods
- SS-EN-16948 - Child protective products - Consumer fitted child resistant locking devices for cupboards and drawers - Safety requirements and test methods
- SS-EN-16955 - Hardware for furniture - Tapered pressure tubes for self-supporting gas springs for the height adjustment of seating - Test methods and requirements for strength and durability
- SS-EN-17191 - Childrens Furniture - Seating for children - Safety requirements and test methods
- SS-EN-17214 - Visual assessment of furniture surfaces
- SS-EN-1725 - Furniture - Beds - Requirements for safety, strength and durability
- SS-EN-1727 - Domestic furniture - Storage furniture - Safety requirements and test methods
- SS-EN-1728 - Furniture - Seating - Test methods for the determination of strength and durability
- SS-EN-1729-1 - Furniture - Chairs and tables for educational institutions - Part 1: Functional dimensions
- SS-EN-1729-2 - Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods
- SS-EN-17737 - Hardware for furniture - Test and evaluation methods for the corrosion resistance of furniture fittings
- SS-EN-17869 - Hardware for furniture - Test methods for strength and overload tests of connectors for furniture constructed from panel material
- SS-EN-17902 - Furniture - Circularity - Evaluation method for dis/re-assembly capability
- SS-EN-1957 - Furniture - Beds and mattresses - Test methods for the determination of functional characteristics and assessment criteria
- SS-EN-1970 - Adjustable beds for disabled persons - Requirements and test methods
- SS-EN-1970-AM1 - Adjustable beds for disabled persons - Requirements and test methods
- SS-EN-312-3 - Particleboards - Specifications - Part 3: Requirements for boards for interior fitments (including furniture) for use in dry conditions
- SS-EN-527-1 - Office furniture - Work tables and desks - Part 1: Dimensions
- SS-EN-527-2 - Office furniture - Work tables - Part 2: Safety, strength and durability requirements
- SS-EN-527-3 - Office furniture - Work tables and desks - Part 3: Methods of test for the determination of the stability and the mechanical strength of the structure
- SS-EN-581-1 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 1: General safety requirements
- SS-EN-581-2 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 2: Mechanical safety requirements and test methods for seating
- SS-EN-581-3 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 3: Mechanical safety requirements for tables
- SS-EN-597-1 - Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 1: Ignition source smouldering cigarette
- SS-EN-597-2 - Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 2: Ignition source: match flame equivalent
- SS-EN-716-1 - Furniture - Children's cots and folding cots for domestic use - Part 1: Safety requirements
- SS-EN-716-2 - Furniture - Children's cots and folding cots for domestic use - Part 2: Test methods
- SS-EN-747-1 - Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements
- SS-EN-747-2 - Furniture - Bunk beds and high beds - Part 2: Test methods
- SS-EN-ISO-105-E16 - Textiles -Tests for colour fastness - Part E16: Colour fastness to water spotting on upholstery fabrics (ISO 105-E16:2006)
- SS-EN-ISO-1107 - Fishing nets - Netting - Basic terms and definitions (ISO 1107:2017)
- SS-ENV-1178-1 - Furniture - Children's high chairs for domestic use - Part 1: Safety requirements (ISO 9221-1 modified)
- SS-ENV-1178-2 - Furniture - Children's high chairs for domestic use - Part 2: Test methods (ISO 9221-2 modified)
- SS-ENV-12520 - Domestic furniture - Seating - Mechanical and structural safety requirements
- SS-ENV-12521 - Domestic furniture - Tables - Mechanical and structural safety requirements
- SS-ENV-13759 - Domestic furniture - Seating - Test method for determination of the durability of reclining and/or tilting mechanisms and operating mechanisms for convertible sofa beds
- SS-ENV-581-2 - Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 2: Mechanical safety requirements and test methods for sampling
- SS-ISO-105-E16 - Textiles -Tests for colour fastness - Part E16: Colour fastness to water spotting on upholstery fabrics (ISO 105-E16, IDT)
- SS-ISO-16131 - Leather - Upholstery leather characteristics - Selection of leather for furniture (ISO 16131:2012, IDT)
- SS-ISO-20189 - Acoustics - Screens, furniture and single objects intended for interior use - Rating of sound absorption and sound reduction of elements based on laboratory measurements (ISO 20189:2018, IDT)
- SS-ISO-3055 - Kitchen equipment - Coordinating sizes (ISO 3055:2021, IDT)
- SS-ISO-7170 - Furniture - Storage units - Determination of strenght and durability (ISO 7170:2005, IDT)
- SS-ISO-7617-1 - Plastics-coated fabrics for upholstery - Part 1: Specification for PVC-coated knitted fabrics
- SS-ISO-7617-2 - Plastics-coated fabrics for upholstery - Part 2: Specification for PVC-coated woven fabrics
- UNE-EN-1729-2 - Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods