Document Center is acquired by Nimonik

Document Center List of Standards on Hoses Hoses For General Use, See 23.040.70

ICS Code 83.140.40

Return to ICS Index.

Up to Level 2:

• 83.140 (Rubber and plastics products Moulding or extrusion products should be classified according to specific products Transmission belts, see 21.220.10 Conveyor belts, see 53.040.20 Rubber and plastics coated fabrics, see 59.080.40 Footwear, see 61.060 Tyres, see 83.160)

The following documents are a part of this series:

ASTM:

• ASTM-F2165 - Standard Specification for Flexible Pre-Insulated Plastic Piping

BSI:

• BS-3832 - Specification for wire reinforced rubber hoses and hose assemblies for hydraulic installations
• BS-4586 - Specification for spiral wire reinforced rubber covered hydraulic hoses and hose assemblies
• BS-4749 - Specification for textile reinforced rubber hydraulic hoses and hose assemblies
• BS-4983 - Specification for textile reinforced thermoplastics hydraulic hoses and hose assemblies
• BS-5842 - Specification for thermoplastic hose assemblies for dock, road and tanker use
• BS-6130-1 - Hose and hose assemblies for asphalt and bitumen.
• BS-6130-2 - Hose and hose assemblies for asphalt and bitumen
• BS-669-2 - Flexible hoses, end fittings and sockets for gas burning appliances
• BS-7038 - Specification for rubber coolant hoses and tubing for use on private cars and light commercial vehicles
• BS-EN-28030 - Rubber or plastics hoses for underground mining. Method of test for flammability
• BS-EN-559 - Gas welding equipment. Rubber hoses for welding, cutting and allied processes
• BS-EN-ISO-1401 - Rubber hoses for agricultural spraying
• BS-EN-ISO-14113 - Gas welding equipment. Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa)
• BS-EN-ISO-16964 - Gas cylinders. Flexible hoses assemblies. Specification and testing
• BS-EN-ISO-1825-TC - Tracked Changes. Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling. Specification
• BS-EN-ISO-21012 - Cryogenic vessels. Hoses
• BS-EN-ISO-21012-TC - Tracked Changes. Cryogenic vessels. Hoses
• BS-EN-ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications. Specification
• BS-EN-ISO-3821 - Gas welding equipment. Rubber hoses for welding, cutting and allied processes
• BS-EN-ISO-3861 - Rubber hoses and hose assemblies for sand and grit blasting. Specification
• BS-EN-ISO-3949 - Plastics hoses and hose assemblies. Textile-reinforced types for hydraulic applications. Specification
• BS-EN-ISO-3949-TC - Tracked Changes. Plastics hoses and hose assemblies. Textile-reinforced types for hydraulic applications. Specification
• BS-EN-ISO-4671-TC - Tracked Changes. Rubber and plastics hoses and hose assemblies. Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
• BS-EN-ISO-5359 - Anaesthetic and respiratory equipment. Low-pressure hose assemblies for use with medical gases
• BS-EN-ISO-5771 - Rubber hoses and hose assemblies for transferring anhydrous ammonia. Specification
• BS-EN-ISO-5771-TC - Tracked Changes. Rubber hoses and hose assemblies for transferring anhydrous ammonia. Specification
• BS-EN-ISO-6806 - Rubber hoses and hose assemblies for use in oil burners. Specification
• BS-EN-ISO-6806-TC - Tracked Changes. Rubber hoses and hose assemblies for use in oil burners. Specification
• BS-EN-ISO-6808 - Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification
• BS-EN-ISO-8028 - Rubber and/or plastics hoses and hose assemblies for airless paint spraying. Specification
• BS-EN-ISO-8028-TC - Tracked Changes. Rubber and/or plastics hoses and hose assemblies for airless paint spraying. Specification
• BS-ISO-10502 - Aerospace. Hose assemblies in polytetrafluoroethylene (PTFE) for use up to 232 C and 10 500 kPa. Technical specifications and requirements
• BS-ISO-11237-1 - Rubber hoses and hose assemblies. Wire-braid-reinforced compact types for hydraulic applications. Specification
• BS-ISO-11237-2 - Rubber hoses and hose assemblies. Wire-braid-reinforced compact types for hydraulic applications. Specification
• BS-ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification
• BS-ISO-11424-TC - Tracked Changes. Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification
• BS-ISO-11425-TC - Tracked Changes. Rubber hoses and hose assemblies for automobile power-steering systems. Specification
• BS-ISO-13775-1 - Thermoplastic tubing and hoses for automotive use
• BS-ISO-13775-1-TC - Tracked Changes. Thermoplastic tubing and hoses for automotive use
• BS-ISO-1436 - Rubber hoses and hose assemblies. Wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification
• BS-ISO-1436-2 - Rubber Hoses & Hose Assemblies, Wire-Braid-Reinforced Hydraulic Types, Specification,
• BS-ISO-16301 - Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for manually operated hydraulic jacks. Specification
• BS-ISO-16964 - Gas cylinders. Flexible hoses assemblies. Specification and testing
• BS-ISO-17324 - Rubber hoses for automotive turbochargers. Specification
• BS-ISO-1823 - Rubber hose and hose assemblies for oil suction and discharge service. Specification
• BS-ISO-19013-1 - Rubber hoses and tubing for fuel circuits for internal combustion engines. Specification
• BS-ISO-19013-2 - Rubber hoses and tubing for fuel circuits for internal combustion engines. Specification
• BS-ISO-19013-2-TC - Tracked Changes. Rubber hoses and tubing for fuel circuits for internal combustion engines. Specification
• BS-ISO-21012 - Cryogenic vessels. Hoses
• BS-ISO-23297 - Thermoplastic hoses and hose assemblies. Wire or synthetic yarn reinforced single-pressure types for hydraulic applications. Specification
• BS-ISO-23297-TC - Tracked Changes. Thermoplastic hoses and hose assemblies. Wire or synthetic yarn reinforced single-pressure types for hydraulic applications. Specification
• BS-ISO-27126 - Thermoplastic multi-layer (nonvulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals. Specification
• BS-ISO-27126-TC - Tracked Changes. Thermoplastic multi-layer (nonvulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals. Specification
• BS-ISO-27127 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas. Specification
• BS-ISO-27127-TC - Tracked Changes. Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas. Specification
• BS-ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications. Specification
• BS-ISO-28702 - Rubber and plastics hoses and tubing. Textile reinforced types. Sub-ambient temperature crush test
• BS-ISO-2928 - Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 2,5 MPa (25 bar). Specification
• BS-ISO-2929 - Rubber hoses and hose assemblies for bulk fuel delivery by truck. Specification
• BS-ISO-2929-TC - Tracked Changes. Rubber hoses and hose assemblies for bulk fuel delivery by truck. Specification
• BS-ISO-3862 - Rubber hoses and hose assemblies. Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids. Specification
• BS-ISO-4079 - Rubber hoses and hose assemblies. Textile-reinforced hydraulic types for oil-based or water-based fluids. Specification
• BS-ISO-4079-2 - Rubber hoses and hose assemblies. Textile-reinforced hydraulic types for oil-based or water-based fluids. Specification
• BS-ISO-4081 - Rubber hoses and tubing for cooling systems for internal-combustion engines. Specification
• BS-ISO-4639-2 - Rubber tubing and hoses for fuel circuits for internal-combustion engines. Specification. Oxygenated fuels
• BS-ISO-4639-3 - Rubber tubing and hoses for fuel circuits for internal-combustion engines. Specification. Oxidized fuels
• BS-ISO-4642-1 - Rubber and plastics hoses, non-collapsible, for fire-fighting service
• BS-ISO-4642-2 - Rubber and plastics hoses, non-collapsible, for fire-fighting service
• BS-ISO-5772 - Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems. Specification
• BS-ISO-6605 - Hydraulic fluid power. Test methods for hoses and hose assemblies
• BS-ISO-6605-TC - Tracked Changes. Hydraulic fluid power. Test methods for hoses and hose assemblies
• BS-ISO-6772 - Aerospace. Fluid systems. Impulse testing of hydraulic hose, tubing and fitting assemblies
• BS-ISO-6804 - Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers. Specification
• BS-ISO-6804-TC - Tracked Changes. Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers - Specification
• BS-ISO-7313 - Aircraft. High temperature convoluted hose assemblies in polytetrafluoroethylene (PTFE)
• BS-ISO-8066-2 - Rubber and plastics hoses and hose assemblies for automotive air conditioning. Specification
• BS-ISO-8066-3 - Rubber and plastics hoses and hose assemblies for automotive air conditioning. Specification
• BS-ISO-8066-4 - Rubber and plastics hoses and hose assemblies for automotive air conditioning. Specification
• BS-ISO-8153-1 - Aerospace fluid systems and components. Vocabulary
• BS-ISO-8789 - Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles. Specification
• BS-ISO-8829-1 - Aerospace. Test methods for polytetraflouroethylene (PTFE) inner-tube hose assemblies
• BS-ISO-8829-2 - Aerospace. Test methods for polytetrafluoroethylene (PTFE) inner-tube hose assemblies
• BS-ISO-8913 - Aerospace. Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400F/3000 psi (204C/20684 kPa) and 204C/21000 kPa (400F/3046 psi). Procurement specification
• BS-ISO-9528 - Aerospace. Standard-weight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 C/ 21 000 kPa. Procurement specification
• BS-ISO-9938 - Aerospace. Polytetrafluoroethylene (PTFE) hose assemblies, classification 204 C/28 000 kPa. Procurement specification

ISO:

• ISO-10502 - Aerospace - Hose assemblies in polytetrafluoroethylene (PTFE) for use up to 232 °C and 10 500 kPa - Technical specifications and requirements
• ISO-11237 - Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
• ISO-11237-2 - Part 2: Water-Based Fluid Applications, Rubber Hoses and Hose Assemblies - Wire-Braid-R
• ISO-11340 - Rubber and rubber products - Hydraulic hose assemblies - External leakage classification for hydraulic systems
• ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification
• ISO-11425 - Rubber hoses and hose assemblies for automobile power-steering systems - Specification
• ISO-11759 - Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) -- Specification
• ISO-12170 - Gas welding equipment - Thermoplastic hoses for welding and allied processes
• ISO-13363 - Rubber and plastics hoses for marine-engine wet-exhaust systems - Specification
• ISO-13774 - Rubber and plastics hoses for fuels for internal-combustion engines - Method of test for flammability
• ISO-13775-1 - Thermoplastic tubing and hoses for automotive use - Part 1: Non-fuel applications
• ISO-13775-2 - Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications
• ISO-1401 - Rubber hoses for agricultural spraying
• ISO-14113 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa)
• ISO-1436 - Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
• ISO-1436-1 - Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• ISO-1436-2 - Part 2: Water-Based Fluid Applications, Rubber Hoses and Hose Assemblies - Wire-Braid-R
• ISO-14557 - Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies
• ISO-14557-1 - Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies - Amendment 1
• ISO-15540 - Ships and marine technology - Fire resistance of non-metallic hose assemblies and non-metallic compensators - Test methods
• ISO-15541 - Ships and marine technology - Fire resistance of non-metallic hose assemblies and non-metallic compensators - Requirements for the test bench
• ISO-16301 - Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for manually operated hydraulic jacks - Specification
• ISO-16964 - Gas cylinders - Flexible hoses assemblies - Specification and testing
• ISO-17324 - Rubber hoses for automotive turbochargers - Specification
• ISO-1823 - Rubber hose and hose assemblies for oil suction and discharge service - Specification
• ISO-1823-1 - Rubber hoses and hose assemblies - Part 1: On-shore oil suction and discharge - Specification
• ISO-1823-2 - Rubber hoses and hose assemblies - Part 2: Ship/dockside discharge - Specification
• ISO-1825 - Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling - Specification
• ISO-19013-1 - Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Part 1: Diesel fuels
• ISO-19013-2 - Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Part 2: Gasoline fuels
• ISO-20444 - Rubber and plastics hoses - Determination of abrasion resistance of the outer cover
• ISO-21012 - Cryogenic vessels - Hoses
• ISO-23297 - Thermoplastic hoses and hose assemblies - Wire or synthetic yarn reinforced single-pressure types for hydraulic applications - Specification
• ISO-27126 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification
• ISO-27127 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification
• ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification
• ISO-28017-AM1 - - Amendment 1
• ISO-2928 - Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 2,5 MPa (25 bar) - Specification
• ISO-2929 - Rubber hoses and hose assemblies for bulk fuel delivery by truck - Specification
• ISO-3821 - Gas welding equipment - Rubber hoses for welding, cutting and allied processes
• ISO-3861 - Rubber hoses and hose assemblies for sand and grit blasting - Specification
• ISO-3862 - Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification
• ISO-3862-1 - Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• ISO-3862-2 - Part 2: Water-Based Fluid Applications, Rubber Hoses & Hose Assemblies - Rubber-Cover
• ISO-3949 - Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification
• ISO-3996 - Road vehicles - Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluid
• ISO-4038 - Road vehicles - Hydraulic braking systems - Simple flare pipes, tapped holes, male fittings and hose end fittings
• ISO-4079 - Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification
• ISO-4079-1 - Rubber hoses and hose assemblies - Textile-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• ISO-4079-2 - Part 2: Water-Based Fluid Applications, Rubber Hoses and Hose Assemblies - Textile-Rein
• ISO-4081 - Rubber hoses and tubing for cooling systems for internal-combustion engines - Specification
• ISO-4639-1 - Rubber tubing and hoses for fuel circuits for internal combustion engines - Specification - Part 1 : Conventional liquid fuels
• ISO-4639-2 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 2: Oxygenated fuels
• ISO-4639-3 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 3: Oxidized fuels
• ISO-4642 - Rubber products - Hoses, non-collapsible, for fire-fighting service
• ISO-4642-1 - Rubber and plastics hoses, non-collapsible, for fire-fighting service - Part 1: Semi-rigid hoses for fixed systems
• ISO-4642-2 - Bicycle tyres and rims - Part 2: Rims
• ISO-4671 - Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
• ISO-4671-AM1 - Rubber and plastics hose and hose assemblies - Methods of measurement of dimensions - Amendment 1: Clarification of position at which outside diameter is measured
• ISO-5359 - Anaesthetic and respiratory equipment - Low-pressure hose assemblies for use with medical gases
• ISO-5359-AM1 - - Amendment 1
• ISO-5771 - Rubber hoses and hose assemblies for transferring anhydrous ammonia - Specification
• ISO-5772 - Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
• ISO-6120 - Road vehicles - Brake hose assemblies for hydraulic braking systems used with petroleum-base brake fluid
• ISO-6605 - Hydraulic fluid power - Test methods for hoses and hose assemblies
• ISO-6772 - Aerospace - Fluid systems - Impulse testing of hydraulic hose, tubing and fitting assemblies
• ISO-6804 - Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers - Specification
• ISO-6805 - Rubber hoses and hose assemblies for underground mining - Wire-reinforced hydraulic types for coal mining - Specification
• ISO-6806 - Rubber hoses and hose assemblies for use in oil burners - Specification
• ISO-6807 - Rubber hoses and hose assemblies for rotary drilling and vibration applications - Specification
• ISO-6808 - Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification
• ISO-7258 - Polytetrafluoroethylene (PTFE) tubing for aerospace applications - Methods for the determination of the density and relative density
• ISO-7313 - Aircraft - High temperature convoluted hose assemblies in polytetrafluoroethylene (PTFE)
• ISO-8028 - Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification
• ISO-8066-1 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 1: Refrigerant 12
• ISO-8066-2 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 2: Refrigerant 134a
• ISO-8066-3 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 3: Refrigerant 1234yf
• ISO-8066-4 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 4: Low vibration transmission type for Refrigerant 1234yf
• ISO-8153-1 - Aerospace fluid systems and components - Vocabulary - Part 1: Hose assemblies
• ISO-8207 - Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes
• ISO-8789 - Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification
• ISO-8829 - Aerospace - Polytetrafluoroethylene (PTFE) hose assemblies - Test methods
• ISO-8829-1 - Aerospace - Test methods for polytetrafluoroethylene (PTFE) inner-tube hose assemblies - Part 1: Metallic (stainless steel) braid
• ISO-8829-2 - Aerospace - Test methods for polytetrafluoroethylene (PTFE) inner-tube hose assemblies - Part 2: Non-metallic braid
• ISO-8913 - Aerospace - Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400 degrees F/3 000 psi (204 degrees C/20 684 kPa) and 204 degrees C/21 000 kPa (400 degrees F/3 046 psi) - Procurement specification
• ISO-9528 - Aerospace - Standard-weight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 °C/21 000 kPa - Procurement specification
• ISO-9938 - Aerospace - Polytetrafluoroethylene (PTFE) hose assemblies, classification 204 °C/28 000 kPa - Procurement specification
• ISO/DIS-11237 - Rubber Hoses and Hose Assemblies - Compact Wire-Braid-Reinforced Hydraulic Types for Oil

Other SDOs:

• EN-ISO-1401 - Rubber hoses for agricultural spraying
• EN-ISO-14113 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
• EN-ISO-14119 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
• EN-ISO-1825 - Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling - Specification
• EN-ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification - Amendment 1
• EN-ISO-3821 - Gas Welding Equipment - Rubber Hoses for Welding, Cutting & Allied Processes
• EN-ISO-3861 - Rubber Hoses for Sand & Grit Blasting - Specification
• EN-ISO-3949 - Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2009)
• EN-ISO-5359 - Anaesthetic and respiratory equipment - Low-pressure hose assemblies for use with medical gases
• EN-ISO-5771 - Rubber Hoses & Hose Assemblies for Transferring Anhydrous Ammonia, Specification
• EN-ISO-6806 - Rubber hoses and hose assemblies for use in oil burners - Specification
• EN-ISO-6807 - Rubber Hoses & Hose Assemblies for Rotary Drilling & Vibration Applications, Specifica
• EN-ISO-6808 - Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification
• JIS-D-2602 - Rubber hoses and tubing for cooling systems for internal-combustion engines -- Specification
• JIS-K-6330-11 - Testing methods for rubber and plastics hoses -- Part 11: Determination of abrasion resistance of the outer cover
• JIS-K-6330-7 - Rubber and plastics hoses -- Part 7: Assessment of ozone resistance under static conditions
• JIS-K-6349-1 - Part 1: Rubber Hoses & Hose Assemblies - Wire-Reinforced Hydraulic Type - Specification, W
• JIS-K-6349-2 - Part 2: Rubber Hoses & Hose Assemblies - Rubber-Covered, Spiral Wire Reinforced, Hydraulic
• JIS-K-6349-3 - Part 3: Wire Reinforced Rubber Hoses, Wire Reinforced Rubber Hoses for Hydraulic
• SIS-ISO/TR-11340 - Rubber and rubber products - Hydraulic hose assemblies - External leakage classification for hydraulic systems
• SS-EN-13286-2 - Unbound and hydraulically bound mixtures - Part 2: Test methods for laboratory reference density and water content - Proctor compaction
• SS-EN-ISO-1401 - Rubber hoses for agricultural spraying (ISO 1401:2016)
• SS-EN-ISO-14113 - Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013)
• SS-EN-ISO-14557 - Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies (ISO 14557:2021)
• SS-EN-ISO-14557-AM1 - Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies (ISO 14557:2002/Amd 1:2007)
• SS-EN-ISO-15540 - Ships and marine technology - Fire resistance of hose assemblies - Test methods (ISO 15540:1999)
• SS-EN-ISO-15541 - Ships and marine technology - Fire resistance of hose assemblies - Requirements for the test bench (ISO 15541:1999)
• SS-EN-ISO-16964 - Gas cylinders - Flexible hoses assemblies - Specification and testing (ISO 16964:2019)
• SS-EN-ISO-1825 - Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling - Specification (ISO 1825:2017)
• SS-EN-ISO-19581 - Measurement of radioactivity - Gamma emitting radionuclides - Rapid screening method using scintillation detector gamma-ray spectrometry (ISO 19581:2017)
• SS-EN-ISO-21012 - Cryogenic vessels - Hoses (ISO 21012:2018)
• SS-EN-ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2018)
• SS-EN-ISO-28017-AM1 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification - Amendment 1 (ISO 28017:2011/Amd 1:2015)
• SS-EN-ISO-3821 - Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO 3821:2019)
• SS-EN-ISO-3861 - Rubber hoses for sand and grit blasting - Specification (ISO 3861:2005)
• SS-EN-ISO-3949 - Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2020)
• SS-EN-ISO-4671 - Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and lengths of hose assemblies (ISO 4671:2007)
• SS-EN-ISO-4671-AM1 - Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
• SS-EN-ISO-5359 - Anaesthetic and respiratory equipment - Low-pressure hose assemblies for use with medical gases (ISO 5359:2014)
• SS-EN-ISO-5771 - Rubber hoses and hose assemblies for transferring anhydrous ammonia - Specification ( (ISO 5771:2008)
• SS-EN-ISO-6806 - Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017)
• SS-EN-ISO-6807 - Rubber hoses and hose assemblies for rotary drilling and vibration applications - Specification (ISO 6807:2003)
• SS-EN-ISO-6808 - Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014)
• SS-EN-ISO/IEC-29147 - Information technology - Security techniques - Vulnerability disclosure (ISO/IEC 29147:2018)
• SS-ISO-11237 - Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification (ISO 11237:2017, IDT)
• SS-ISO-11237-1 - Rubber hoses and hose assemblies - Wire-braid-reinforced compact types for hydraulic applications - Specification - Part 1: Oil-based fluid applications (ISO 11237-1:2004, IDT)
• SS-ISO-11237-2 - Rubber hoses and hose assemblies - Wire-braid-reinforced compact types for hydraulic applications - Specification - Part 2: Water-based fluid applications (ISO 11237-2:2006, IDT)
• SS-ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification (ISO 11424:2023, IDT)
• SS-ISO-11425 - Rubber hoses and hose assemblies for automobile power-steering systems - Specification (ISO 11425:2018, IDT)
• SS-ISO-11759 - Rubber hoses and hose assemblies for dispensing liquefied petroleum gas (LPGs) - Specification
• SS-ISO-11898-1 - Road vehicles - Controller area network (CAN) - Part 1: Data link layer and physical signalling (ISO 11898-1:2015, IDT)
• SS-ISO-1217 - Displacement compressors - Acceptance test (ISO 1217:2009, IDT)
• SS-ISO-13363 - Rubber and plastics hoses for marine-engine wet-exhaust systems - Specification (ISO 13363:2015, IDT)
• SS-ISO-13774 - Rubber and plastics hoses for fuels for internal-combustion engines - Method of test for flammability
• SS-ISO-13775-1 - Thermoplastic tubing and hoses for automotive use - Part 1: Non-fuel applications (ISO 13775-1:2021, IDT)
• SS-ISO-13775-2 - Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications (ISO 13775-2:2016, IDT)
• SS-ISO-1436 - Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification (ISO 1436:2020, IDT)
• SS-ISO-1436-1 - Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• SS-ISO-1436-2 - Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types - Specification - Part 2: Water-based fluid applications (ISO 1436-2:2005, IDT)
• SS-ISO-15540 - Ships and marine technology - Fire resistance of hose assemblies - Test methods
• SS-ISO-15541 - Ships and marine tehnology - Fire resistance of hose assemblies - Requirements for the test bench
• SS-ISO-16301 - Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for manually operated hydraulic jacks - Specification (ISO 16301:2017, IDT)
• SS-ISO-16526-3 - Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 3: Spectrometric method (ISO 16526-3:2011, IDT)
• SS-ISO-16964 - Gas cylinders - Flexible hoses assemblies - Specification and testing (ISO 16964:2019, IDT)
• SS-ISO-1823-1 - Rubber hoses and hose assemblies - Part 1: On-shore oil suction and discharge - Specification
• SS-ISO-1823-2 - Rubber hoses and hose asssemblies - Part 2: Ship/dockside discharge - Specification
• SS-ISO-1825 - Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling - Specification (ISO 1825:2010, IDT)
• SS-ISO-19013-1 - Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Part 1: Diesel fuels (ISO 19013-1:2019, IDT)
• SS-ISO-19013-2 - Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Part 2: Gasoline fuels (ISO 19013-2:2005, IDT)
• SS-ISO-1919 - Road vehicles - M14 x 1,25 spark-plugs with flat seating and their cylinder head housings
• SS-ISO-2093 - Electroplated coating of tin - Specification and test methods
• SS-ISO-23297 - Thermoplastics hoses and hose assemblies - Wire or synthetic yarn reinforced single-pressure types for hydraulic applications - Specification (ISO 23297:2008, IDT)
• SS-ISO-27126 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification (ISO 27126:2021, IDT)
• SS-ISO-27127 - Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification (ISO 27127:2021, IDT)
• SS-ISO-28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2009, IDT)
• SS-ISO-2929 - Rubber hoses and hose assemblies for bulk fuel delivery by truck - Specification (ISO 2929:2021, IDT)
• SS-ISO-3387 - Rubber - Determination of crystallization effects by hardness measurements (ISO 3387:2020, IDT)
• SS-ISO-3500 - Gas cylinders - Seamless steel CO2 cylinders for fixed fire-fighting installation on ships (ISO 3500:2005, IDT)
• SS-ISO-3862 - Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification (ISO 3862:2020, IDT)
• SS-ISO-3862-1 - Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• SS-ISO-3862-2 - Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types - Specification - Part 2: Water-based fluid applications (ISO 3862-2:2005, IDT)
• SS-ISO-3949 - Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification (ISO 3949:2009, IDT)
• SS-ISO-4079 - Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - Specification (ISO 4079:2020, IDT)
• SS-ISO-4079-1 - Rubber hoses and hose assemblies - Textile-reinforced hydraulic types - Specification - Part 1: Oil-based fluid applications
• SS-ISO-4079-2 - Rubber hoses and hose assemblies - Textile-reinforced hydraulic types - Specification - Part 2: Water-based fluid applications (ISO 4079-2:2005, IDT)
• SS-ISO-4081 - Rubber hoses and tubing for cooling systems for internal-combustion engines - Specification (ISO 4081:2016, IDT)
• SS-ISO-4113 - Road vehicles - Calibration fluids for diesel injection equipment (ISO 4113:2010, IDT)
• SS-ISO-4141 - Road vehicles - Seven-core connecting cables
• SS-ISO-4148 - Road vehicles - Special warning lamps - Dimensions (ISO 4148:2004, IDT)
• SS-ISO-4209-1 - Truck and bus tyres and rims (metric series) - Part 1: Tyres
• SS-ISO-4639-1 - Rubber tubing and hoses for fuel circuits for internal combustion engines - Specification - Part 1: Conventional liquid fuels
• SS-ISO-4639-2 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 2: Oxygenated fuels
• SS-ISO-4639-3 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 3: Oxidized fuels
• SS-ISO-4642-1 - Rubber and plastics hoses, non-collapsible, for fire-fighting service - Part 1: Semi-rigid hoses for fixed systems (ISO 4642-1:2009, IDT)
• SS-ISO-4642-2 - Rubber and plastics hoses, non-collapsible, for fire-fighting service - Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles (ISO 4642-2:2009, IDT)
• SS-ISO-4671 - Rubber and plastics hoses and hose assemblies - Methods of measurement of dimensions
• SS-ISO-5772 - Rubber hoses and hoses assemblies for measured fuel dispensing - Specification
• SS-ISO-6134 - Rubber hoses and hose assemblies for steam - Specification
• SS-ISO-6605 - Hydraulic fluid power - Test methods for hoses and hose assemblies (ISO 6605:2017, IDT)
• SS-ISO-6804 - Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers - Specification (ISO 6804:2023, IDT)
• SS-ISO-6805 - Rubber hoses and hose assemblies for underground mining - Wire-reinforced hydraulic types for coal mining - Specification (ISO 6805:2020, IDT)
• SS-ISO-6807 - Rubber hoses and hose assemblies for rotary drilling and vibration applications - Specification (ISO 6807:2003, IDT)
• SS-ISO-8066-2 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 2: Refrigerant 134a
• SS-ISO-8066-3 - Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Part 3: Refrigerant 1234yf (ISO 8066-3:2020, IDT)
• SS-ISO-8066-4 - Rubber and plastics hoses and hose assemblies for automotive air conditioning — Specification — Part 4: Low vibration transmission type for Refrigerant 1234yf (ISO 8066-4:2023, IDT)
• SS-ISO-8789 - Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - Specification (ISO 8789:2020, IDT)
• SS-ISO-8829-2 - Aerospace - Test methods for polytetrafluoroethylene (PTFE) innertube hose assemblies - Part 2 Non-metallic braid (ISO 8829-2:2006, IDT)
• SS-ISO/TR-2329 - Truckar och lyftvagnar - Gaffeltruckar - Gaffelarmar - Mått,SAKNAS
• UNE-EN-ISO-3949 - Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification