Document Center is acquired by Nimonik

Document Center List of Standards on Plastics Pipes And Fittings For Non Fluid Use Plastics Pipes, Fittings And Valves For General Use, See 23.040.20, 23.040.45 And 23.060

ICS Code 83.140.30

Return to ICS Index.

Up to Level 2:

• 83.140 (Rubber and plastics products Moulding or extrusion products should be classified according to specific products Transmission belts, see 21.220.10 Conveyor belts, see 53.040.20 Rubber and plastics coated fabrics, see 59.080.40 Footwear, see 61.060 Tyres, see 83.160)

The following documents are a part of this series:

ASTM:

• ASTM-D2837 - Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
• ASTM-D6457 - Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) (Withdrawn 2018)
• ASTM-F1960 - Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
• ASTM-F1962 - Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
• ASTM-F1970 - Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems
• ASTM-F2023 - Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Pipe, Tubing and Systems to Hot Chlorinated Water
• ASTM-PS106 - Provisional Standard Specification for Rods and Tubes of Polyethylene (PE)

BSI:

• BS-4514 - Unplasticized PVC soil and ventilating pipes of 82.4 mm minimum mean outside diameter, and fittings and accessories of 82.4 mm and of other sizes. Specification
• BS-4660 - Thermoplastics ancillary fittings of nominal sizes 110 and 160 for belowground gravity drainage and sewerage. Specification
• BS-4660-TC - Tracked Changes. Thermoplastics ancillary fittings of nominal sizes 110 and 160 for belowground gravity drainage and sewerage. Specification
• BS-5255 - Specification for thermoplastics waste pipe and fittings
• BS-5409-1 - Specification for nylon tubing
• BS-5409-2 - Specification for nylon tubing. Plasticized and unplasticized nylon tubing types 11 and 12 for use primarily in the automobile industry
• BS-5480 - Specification for glass reinforced plastics (GRP) pipes, joints and fittings for use for water supply or sewerage
• BS-5955-8 - Plastics pipework (thermoplastics materials)
• BS-7291-1 - Thermoplastics pipe and tting systems for hot and cold water for domestic purposes and heating installations in buildings
• BS-7291-2 - Thermoplastics pipe and ?tting systems for hot and cold water for domestic purposes and heating installations in buildings
• BS-7291-3 - Thermoplastics pipe and ?tting systems for hot and cold water for domestic purposes and heating installations in buildings
• BS-7291-4 - Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings. Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement
• BS-7336 - Specification for polyethylene fusion fittings with integral heating element(s) for use with polyethylene pipes for the conveyance of gaseous fuels
• BS-879-2 - Water well casing
• BS-EN-1115-1 - Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
• BS-EN-1329-1 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U)
• BS-EN-13566-1 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks
• BS-EN-13566-2 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks
• BS-EN-13566-3 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks
• BS-EN-13566-4 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks
• BS-EN-1437 - Plastics piping systems. Piping systems for underground drainage and sewerage. Test method for resistance to combined temperature cycling and external loading
• BS-EN-1451-1 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP)
• BS-EN-14541-1 - Plastics pipes and fittings. Utilisation of thermoplastics recyclates
• BS-EN-1455-1 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS)
• BS-EN-1456-1 - Plastic piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U)
• BS-EN-1519-1 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE)
• BS-EN-1636-3 - Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
• BS-EN-1636-5 - Plastics piping systems for non-pressure drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
• BS-EN-1636-6 - Plastics Piping Systems for Non-Pressure Drainage & Sewerage, Glass-Reinforced Thermos
• BS-EN-ISO-14692-1 - Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping
• BS-EN-ISO-14692-1-TC - Tracked Changes. Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping
• BS-EN-ISO-14692-2 - Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping
• BS-EN-ISO-14692-3 - Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping
• BS-EN-ISO-14692-4 - Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping
• BS-EN-ISO-16486-1 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-EN-ISO-16486-1-TC - Tracked Changes. Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-EN-ISO-16486-2 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-EN-ISO-16486-3 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-EN-ISO-16486-4 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-EN-ISO-8233-TC - Tracked Changes. Thermoplastics valves. Torque. Test method
• BS-ISO-10838-1 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels
• BS-ISO-10838-2 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels
• BS-ISO-10838-3 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels
• BS-ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification
• BS-ISO-11424-TC - Tracked Changes. Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification
• BS-ISO-13775-1 - Thermoplastic tubing and hoses for automotive use
• BS-ISO-13775-1-TC - Tracked Changes. Thermoplastic tubing and hoses for automotive use
• BS-ISO-14531-2 - Plastics pipes and fittings. Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels. Metric series. Specifications
• BS-ISO-14531-3 - Plastics pipes and fittings. Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels. Metric series. Specifications
• BS-ISO-14531-4 - Plastics pipes and fittings. Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels. Metric series. Specifications
• BS-ISO-15840 - Ships and marine technology. Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
• BS-ISO-16486-1 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-ISO-16486-6 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing
• BS-ISO-22621-5 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar). Polyamide (PA)
• BS-ISO-22621-6 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar). Polyamide (PA)
• BS-ISO-4437 - Buried polyethylene (PE) pipes for the supply of gaseous fuels. Metric series. Specifications
• BS-ISO-4437-1 - Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-1-TC - Tracked Changes. Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-2 - Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-2-TC - Tracked Changes. Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-3 - Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-4 - Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-4-TC - Tracked Changes. Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-5 - Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-4437-5-TC - Tracked Changes. Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE)
• BS-ISO-7628 - Road vehicles. Thermoplastics tubing for air braking systems
• DD-CEN-1456-2 - Plastic piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U)
• DD-ENV-1329-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U)
• DD-ENV-13801 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation
• DD-ENV-1401-3 - Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U)
• DD-ENV-1451-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP)
• DD-ENV-1519-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE)
• DD-ENV-1565-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC)
• DD-ENV-1566-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C)
• PD-CEN-1329-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U)
• PD-CEN-13801 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation
• PD-CEN-1451-2 - Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP)
• PD-CEN-14541-2 - Plastics pipes and fittings. Utilisation of thermoplastics recyclates
• PD-CEN-1519-2 - Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE)
• PD-CEN-1565-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene-copolymer blends (SAN+PVC)
• PD-CEN-1566-2 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C)
• PD-CEN-ISO-16486-7 - Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing

ISO:

• ISO-10467 - Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
• ISO-10639 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
• ISO-10838-1 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels -- Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
• ISO-10838-3 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels -- Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
• ISO-10931-4 - Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Part 4: Valves
• ISO-10933 - Polyethylene (PE) valves for gas distribution systems
• ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification
• ISO-12092 - Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure -- Resistance to internal pressure -- Test method
• ISO-12176-4 - Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 4: Traceability coding
• ISO-13775-1 - Thermoplastic tubing and hoses for automotive use - Part 1: Non-fuel applications
• ISO-13775-2 - Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications
• ISO-13844 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with plastic pipes - Test method for leaktightness under negative pressure, angular deflection and deformation
• ISO-13845 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressure and with angular deflection
• ISO-14236 - Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
• ISO-14531-1 - Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series Specifications - Part 1: Pipes
• ISO-14692-1 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials
• ISO-14692-2 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture
• ISO-14692-3 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design
• ISO-14692-4 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation
• ISO-15840 - Ships and marine technology - Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
• ISO-15874-7 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity
• ISO-15875-1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General
• ISO-15875-2 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes
• ISO-15875-3 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings
• ISO-15875-5 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system
• ISO-15875-7 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity
• ISO-15876-1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General
• ISO-15876-2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes
• ISO-15876-3 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings
• ISO-15876-5 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system
• ISO-15876-7 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 7: Guidance for the assessment of conformity
• ISO-16486-1 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General
• ISO-16486-1-AM1 - - Amendment 1
• ISO-16486-2 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes
• ISO-16486-2-AM1 - - Amendment 1
• ISO-16486-3 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings
• ISO-16486-3-AM1 - - Amendment 1
• ISO-16486-4 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves
• ISO-16486-5 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system
• ISO-16486-6 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 6: Code of practice for design, handling and installation
• ISO-16486-7 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity
• ISO-16486-8 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 8: Training and assessment of fusion operators
• ISO-19220 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Styrene copolymer blends (SAN + PVC)
• ISO-22621-1 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 1: General
• ISO-22621-2 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 2: Pipes
• ISO-22621-3 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 3: Fittings
• ISO-22621-5 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 5: Fitness for purpose of the system
• ISO-22621-6 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 6: Code of practice for design, handling and installation
• ISO-265-1 - Pipes and fittings of plastics materials - Fittings for domestic and industrial waste pipes - Basic dimensions : Metric series - Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
• ISO-2703 - Buried unplasticized polyvinyl chloride (PVC) pipes for the supply of gaseous fuels -- Metric series -- Specification
• ISO-3114 - Unplasticized polyvinyl chloride (PVC) pipes for potable water supply - Extractability of lead and tin - Test method
• ISO-3633 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U)
• ISO-4422-1 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 1: General
• ISO-4422-2 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 2: Pipes (with or without integral sockets)
• ISO-4422-3 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 3: Fittings and joints
• ISO-4422-4 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 4: Valves and ancillary equipment
• ISO-4422-5 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 5: Fitness for purpose of the system
• ISO-4427 - Polyethylene (PE) pipes for water supply - Specifications
• ISO-4435 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U)
• ISO-4437 - Buried polyethylene (PE) pipes for the supply of gaseous fuels -- Metric series -- Specifications
• ISO-4437-1 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
• ISO-4437-2 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
• ISO-4437-3 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
• ISO-4437-4 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
• ISO-4437-5 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
• ISO-4639-1 - Rubber tubing and hoses for fuel circuits for internal combustion engines - Specification - Part 1 : Conventional liquid fuels
• ISO-4639-2 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 2: Oxygenated fuels
• ISO-4639-3 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 3: Oxidized fuels
• ISO-6992 - Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply - Extractability of cadmium and mercury occurring as impurities
• ISO-6993 - Buried, high-impact poly(vinyl chloride) (PVC-HI) pipes for the supply of gaseous fuels - Specifications
• ISO-6993-1 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 1: Pipes for a maximum operating pressure of 1 bar (100 kPa)
• ISO-6993-2 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 2: Fittings for a maximum operating pressure of 200 mbar (20 kPa)
• ISO-6993-3 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 3: Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa)
• ISO-6993-4 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 4: Code of practice for design, handling and installation
• ISO-7349 - Thermoplastics valves - Connection references
• ISO-7508 - Unplasticized polyvinyl chloride (PVC-U) valves for pipes under pressure - Basic dimensions - Metric series
• ISO-7628 - Road vehicles - Thermoplastics tubing for air braking systems
• ISO-7628-1 - Road vehicles - Thermoplastics tubing for use in air braking systems - Part 1: Dimensions and marking
• ISO-7628-2 - Corrigendum
• ISO-7671 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
• ISO-7682 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS)
• ISO-8085-1 - Corrigendum
• ISO-8085-2 - Corrigendum
• ISO-8085-3 - Corrigendum
• ISO-8233 - Thermoplastics valves - Torque - Test method
• ISO-8242 - Polypropylene (PP) valves for pipes under pressure - Basic dimensions - Metric series
• ISO-8283-1 - Plastics pipes and fittings - Dimensions of sockets and spigots for discharge systems inside buildings - Part 1: Unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C)
• ISO-8283-2 - Plastics pipes and fittings - Dimensions of sockets and spigots for discharge systems inside buildings - Part 2: Polyethylene (PE)
• ISO-8283-3 - Plastics pipes and fittings - Dimensions of sockets and spigots for discharge systems inside buildings - Part 3: Polypropylene (PP)
• ISO-8283-4 - Plastics pipes and fittings - Dimensions of sockets and spigots for discharge systems inside buildings - Part 4: Acrylonitrile/butadiene/styrene (ABS)
• ISO-8659 - Thermoplastics valves - Fatigue strength - Test method
• ISO-8770 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE)
• ISO-8795 - Plastics piping systems for the transport of water intended for human consumption -- Migration assessment -- Determination of migration values of plastics pipes and fittings and their joints
• ISO-9393-1 - Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 1: General
• ISO-9393-2 - Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 2: Test conditions and basic requirements
• ISO-9625 - Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes
• ISO-9808 - Solar water heaters - Elastomeric materials for absorbers, connecting pipes and fittings - Method of assessment
• ISO-9896 - Plastics traps for discharge pipework systems inside buildings

Other SDOs:

• DIN-16876 - Pipes and fittings of high-density polyethylene (PE-HD) for buried cable ducting - Dimensions and technical delivery condition
• DIN-EN-ISO-9080 - Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
• EN-ISO-14692-1 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials
• EN-ISO-14692-2 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture
• EN-ISO-14692-3 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design
• EN-ISO-14692-4 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation
• JIS-K-6741 - Unplasticized poly(vinyl chloride) (PVC-U) pipes
• JIS-K-6762 - Double wall polyethylene pipes for water supply
• JIS-K-6770 - Crosslinked polyethylene (PE-X) pipe fittings
• JIS-K-6770-A3 - Crosslinked polyethylene (PE-X) pipe fittings (Amendment 3)
• JIS-K-6776 - Chlorinated poly(vinyl chloride) (PVC-C) pipes for hot and cold water supply
• JIS-K-6777-A2 - Chlorinated poly (vinyl chloride) (PVC-C) pipe fittings for hot and cold water supply (Amendment 2)
• JIS-K-6779 - Polybutene (PB) pipe fittings
• JIS-K-6779-A2 - Polybutene (PB) pipe fittings (Amendment 2)
• JIS-K-6787 - Crosslinked polyethylene (PE-X) pipes for water supply
• JIS-K-6788 - Crosslinked polyethylene (PE-X) pipe fittings for water supply
• JIS-K-6788-A2 - Crosslinked polyethylene (PE-X) pipe fittings for water supply (Amendment 2)
• JIS-K-6793-A2 - Polybutene (PB) pipe fittings for water supply (Amendment 2)
• SIS-CEN/TS-14541-2 - Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 2: Recommendations for relevant characteristics
• SS-EN-12099 - Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
• SS-EN-12107 - Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment- Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components
• SS-EN-12118 - Plastics piping systems - Determination of moisture content in thermoplastics by coulometry
• SS-EN-13108-3 - Bituminous mixtures - Material specifications - Part 3: Soft Asphalt
• SS-EN-13108-4 - Bituminous mixtures - Material specifications - Part 4: Hot Rolled Asphalt
• SS-EN-13956 - Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics
• SS-EN-14541-1 - Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
• SS-EN-14735 - Characterization of waste - Preparation of waste samples for ecotoxicity tests
• SS-EN-728 - Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
• SS-EN-ISO-13844 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes - Test method for leak tightness under negative pressure, angular deflection and deformation (ISO 13844:2022)
• SS-EN-ISO-13845 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2015)
• SS-EN-ISO-14692-1 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2017)
• SS-EN-ISO-14692-2 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2017)
• SS-EN-ISO-14692-3 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2017)
• SS-EN-ISO-14692-4 - Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2017)
• SS-EN-ISO-16486-1 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2020)
• SS-EN-ISO-16486-2 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
• SS-EN-ISO-16486-3 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO 16486-3:2020)
• SS-EN-ISO-16486-4 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
• SS-EN-ISO-16486-5 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system (ISO 16486-5:2021)
• SS-EN-ISO-17201-1 - Acoustics - Noise from shooting ranges - Part 1: Determination of muzzle blast by measurement (ISO 17201-1:2018)
• SS-ENV-852 - Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values
• SS-ISO-10467 - Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 10467:2018, IDT)
• SS-ISO-10467-AM1 - Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester (UP) resin - Amendment 1 (ISO 10467:2004/Amd 1:2012, IDT)
• SS-ISO-10639 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 10639:2004, IDT)
• SS-ISO-10639-AM1 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1 (ISO 10639:2004/Amd 1:2011, IDT)
• SS-ISO-10838-3 - Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
• SS-ISO-11424 - Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification (ISO 11424:2023, IDT)
• SS-ISO-12176-4 - Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 4: Traceability coding
• SS-ISO-13775-1 - Thermoplastic tubing and hoses for automotive use - Part 1: Non-fuel applications (ISO 13775-1:2021, IDT)
• SS-ISO-13775-2 - Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications (ISO 13775-2:2016, IDT)
• SS-ISO-14236 - Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
• SS-ISO-14531-1 - Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 1: Pipes
• SS-ISO-14531-2 - Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the transport of gaseous fuels - Metric series - Specifications - Part 2: Fittings for heat fusion jointing (ISO 14531-2:2004, IDT)
• SS-ISO-16486-6 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 6: Code of practice for design, handling and installation (ISO 16486-6:2012, IDT)
• SS-ISO-19220 - Plastics piping systems for soil and waste discharge (low and high) temperature inside buildings - Styrene copolymer blends (SAN + PVC) (ISO 19220:2004, IDT)
• SS-ISO-22621-1 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 1: General (ISO 22621-1:2007, IDT)
• SS-ISO-22621-2 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 2: Pipes (ISO 22621-2:2007, IDT)
• SS-ISO-22621-3 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 3: Fittings (ISO 22621-3:2007, IDT)
• SS-ISO-22621-5 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 5: Fitness for purpose of the system (ISO 22621-5:2010, IDT)
• SS-ISO-22621-6 - Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) - Polyamide (PA) - Part 6: Code of practice for design, handling and installation (ISO 22621-6:2010, IDT)
• SS-ISO-3387 - Rubber - Determination of crystallization effects by hardness measurements (ISO 3387:2020, IDT)
• SS-ISO-4435 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) (ISO 4435:2002, IDT)
• SS-ISO-4437 - Buried polyethylene (PE) pipes for the supply of gaseous fuels - Metric series - Specifications (ISO 4437:2007, IDT)
• SS-ISO-4639-1 - Rubber tubing and hoses for fuel circuits for internal combustion engines - Specification - Part 1: Conventional liquid fuels
• SS-ISO-4639-2 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 2: Oxygenated fuels
• SS-ISO-4639-3 - Rubber tubing and hoses for fuel circuits for internal-combustion engines - Specification - Part 3: Oxidized fuels
• SS-ISO-6993-1 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 1: Pipes for a maximum operating pressure of 1 bar (100 kPa) (ISO 6993-1:2006, IDT)
• SS-ISO-6993-2 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 2: Fittings for a maximum operating pressure of 200 mbar (20 kPa) (ISO 6993-2:2006, IDT)
• SS-ISO-6993-3 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 3: Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa) (ISO 6993-3:2006, IDT)
• SS-ISO-6993-4 - Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 4: Code of practice for design, handling and installation (ISO 6993-4:2006, IDT)
• SS-ISO-7628 - Road vehicles - Thermoplastics tubing for air braking systems (ISO 7628:2010, IDT)
• SS-ISO-7628-2 - Road vehicles - Thermoplastics tubing for air braking system - Part 2: Mounting on vehicle and test methods
• SS-ISO-7671 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP) (ISO 7671:2003, IDT)
• SS-ISO-7675 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Chlorinated poly(vinyl chloride) (PVC-C) (ISO 7675:2003, IDT)
• SS-ISO-7682 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS) (ISO 7682:2003, IDT)
• SS-ISO-8085-1 - Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Part 1: Fittings for socket fusion using heated tools
• SS-ISO-8085-2 - Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings
• SS-ISO-8085-3 - Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Part 3: Electrofusion fittings
• SS-ISO-8770 - Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE) (ISO 8770:2003, IDT)
• SS-ISO-8779 - Plastics piping systems - Polyethylene (PE) pipes for irrigation - Specifications (ISO 8779:2010, IDT)
• SS-ISO-8779-AM1 - Plastics piping systems - Polyethylene (PE) pipes for irrigation - Specifications - Amendment 1 (ISO 8779:2010/Amd 1:2014, IDT)
• SS-ISO-8796 - Polyethylene (PE) 32 and PE 40 pipes for irrigation laterals - Susceptibility to environmental stress cracking induced by insert-type fittings - Test method and requirements (ISO 8796:2004, IDT)
• SS-ISO-9393-2 - Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 2: Test conditions and basic requirements (ISO 9393-2:2005, IDT)
• UNE-EN-ISO-17778 - Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
• UNE-EN-ISO-9969 - Thermoplastics pipes - Determination of ring stiffness