Document Center List of Standards on Refractories Including Ceramic Refractories
ICS Code 81.080
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-C1054 - Standard Practice for Pressing and Drying Refractory Plastic and Ramming Mix Specimens
- ASTM-C107 - Method of Panel Spalling Testing High-Duty Fireclay Brick (Withdrawn 1994)
- ASTM-C1099 - Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
- ASTM-C1100 - Standard Test Method for Ribbon Thermal Shock Testing of Refractory Materials (Withdrawn 2005)
- ASTM-C1106 - Standard Test Methods for Chemical Resistance and Physical Properties of Carbon Brick (Withdrawn 2021)
- ASTM-C1113 - Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)
- ASTM-C113 - Standard Test Method for Reheat Change of Refractory Brick
- ASTM-C1160 - Standard Specification for Chemical-Resistant Carbon Brick (Withdrawn 2021)
- ASTM-C1171 - Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories
- ASTM-C122 - Test Method for Panel Spalling Testing Super-Duty Fireclay Brick (Withdrawn 1994)
- ASTM-C1223 - Standard Test Method for Testing of Glass Exudation from AZS Fusion-Cast Refractories
- ASTM-C126 - Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
- ASTM-C1261 - Standard Specification for Firebox Brick for Residential Fireplaces
- ASTM-C1298 - Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys (Withdrawn 2024)
- ASTM-C133 - Standard Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractories
- ASTM-C134 - Standard Test Methods for Size, Dimensional Measurements, and Bulk Density of Refractory Brick and Insulating Firebrick
- ASTM-C135 - Standard Test Method for True Specific Gravity of Refractory Materials by Water Immersion
- ASTM-C1407 - Standard Practice for Calculating Areas, Volume, and Linear Change of Refractory Shapes
- ASTM-C1419 - Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young’s Modulus
- ASTM-C1445 - Standard Test Method for Measuring Consistency of Castable Refractory Using a Flow Table
- ASTM-C1446 - Standard Test Method for Measuring Consistency of Self-Flowing Castable Refractories
- ASTM-C1547 - Standard Classification for Fusion-Cast Refractory Blocks and Shapes
- ASTM-C1548 - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio of Refractory Materials by Impulse Excitation of Vibration
- ASTM-C155 - Standard Classification of Insulating Firebrick
- ASTM-C159 - Standard Specification for Vitrified Clay Filter Blocks
- ASTM-C16 - Standard Test Method for Load Testing Refractory Shapes at High Temperatures
- ASTM-C179 - Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens
- ASTM-C181 - Standard Test Method for Workability Index of Fireclay and High-Alumina Refractory Plastics
- ASTM-C182 - Standard Test Method for Thermal Conductivity of Insulating Firebrick
- ASTM-C20 - Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water
- ASTM-C201 - Standard Test Method for Thermal Conductivity of Refractories
- ASTM-C202 - Standard Test Method for Thermal Conductivity of Refractory Brick
- ASTM-C210 - Standard Test Method for Reheat Change of Insulating Firebrick
- ASTM-C212 - Standard Specification for Structural Clay Facing Tile
- ASTM-C24 - Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High-Alumina Refractory Materials
- ASTM-C27 - Standard Classification of Fireclay and High-Alumina Refractory Brick
- ASTM-C288 - Standard Test Method for Disintegration of Refractories in an Atmosphere of Carbon Monoxide
- ASTM-C34 - Standard Specification for Structural Clay Loadbearing Wall Tile
- ASTM-C356 - Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
- ASTM-C357 - Standard Test Method for Bulk Density of Granular Refractory Materials
- ASTM-C38 - Method for Panel Spalling Testing Refractory Brick (Withdrawn 1994)
- ASTM-C401 - Standard Classification of Alumina and Alumina-Silicate Castable Refractories
- ASTM-C411 - Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
- ASTM-C416 - Standard Classification of Silica Refractory Brick
- ASTM-C417 - Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories
- ASTM-C43 - Standard Terminology of Structural Clay Products (Withdrawn 2009)
- ASTM-C435 - Standard Classification of Steel Pouring Pit Fireclay Refractories (Withdrawn 2001)
- ASTM-C455 - Standard Classification of Chrome, Chrome-Magnesia, Magnesia-Chrome, and Magnesia Brick
- ASTM-C456 - Standard Test Method for Hydration Resistance of Basic Bricks and Shapes
- ASTM-C467 - Standard Classification of Mullite Refractories
- ASTM-C491 - Test Method for Modulus of Rupture of Air-Setting Plastic Refractories (Withdrawn 1992)
- ASTM-C492 - Standard Test Method for Hydration of Granular Dead-Burned Refractory Dolomite
- ASTM-C493 - Standard Test Method for Bulk Density and Porosity of Granular Refractory Materials by Mercury Displacement (Withdrawn 2002)
- ASTM-C530 - Standard Specification for Structural Clay Nonloadbearing Screen Tile
- ASTM-C545 - Standard Classification of Zircon Refractories
- ASTM-C56 - Standard Specification for Structural Clay Nonloadbearing Tile
- ASTM-C574 - Method for Chemical Analyisis of Magnesite and Dolomite Refractories
- ASTM-C577 - Standard Test Method for Permeability of Refractories
- ASTM-C583 - Standard Test Method for Modulus of Rupture of Refractory Materials at Elevated Temperatures
- ASTM-C604 - Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer
- ASTM-C605 - StandardTest Method for Reheat Change of Fireclay Nozzles and Sleeves (Withdrawn 1997)
- ASTM-C607 - Standard Practice for Coking Large Shapes of Carbon-Bearing Materials
- ASTM-C620 - Test Method for Hydration Resistance of Pitch-Bearing Basic Refractory Brick (Withdrawn 1996)
- ASTM-C621 - Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass
- ASTM-C622 - Standard Test Method for Corrosion Resistance of Refractories to Molten Glass Using the Basin Furnace (Withdrawn 2000)
- ASTM-C67 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
- ASTM-C673 - Standard Classification of Fireclay and High-Alumina Plastic Refractories and Ramming Mixes
- ASTM-C704 - Standard Test Method for Abrasion Resistance of Refractory Materials at Room Temperature
- ASTM-C71 - Standard Terminology Relating to Refractories
- ASTM-C767 - Standard Test Method for Thermal Conductivity of Carbon Refractories
- ASTM-C768 - Standard Practice for Drip Slag Testing Refractory Materials at High Temperature (Withdrawn 2004)
- ASTM-C830 - Standard Test Methods for Apparent Porosity, Liquid Absorption, Apparent Specific Gravity, and Bulk Density of Refractory Shapes by Vacuum Pressure
- ASTM-C832 - Standard Test Method of Measuring Thermal Expansion and Creep of Refractories Under Load
- ASTM-C838 - Standard Test Method for Bulk Density of As-Manufactured Carbon and Graphite Shapes
- ASTM-C860 - Standard Test Method for Determining the Consistency of Refractory Castable Using the Ball-In-Hand Test
- ASTM-C861 - Standard Practice for Determining Metric Dimensions of Standard Series Refractory Brick and Shapes
- ASTM-C862 - Standard Practice for Preparing Refractory Concrete Specimens by Casting
- ASTM-C863 - Standard Test Method for Evaluating Oxidation Resistance of Silicon Carbide Refractories at Elevated Temperatures
- ASTM-C865 - Standard Practice for Firing Refractory Concrete Specimens
- ASTM-C874 - Standard Test Method for Rotary Slag Testing of Refractory Materials (Withdrawn 2020)
- ASTM-C885 - Standard Test Method for Young's Modulus of Refractory Shapes by Sonic Resonance
- ASTM-C899 - Standard Practice for Use of Metric Units of Measure for Reporting Properties of Refractory Materials
- ASTM-C903 - Standard Practice for Preparing Refractory Specimens by Cold Gunning
- ASTM-C909 - Standard Practice for Dimensions of a Modular Series of Refractory Brick and Shapes
- ASTM-C914 - Standard Test Method for Bulk Density and Volume of Solid Refractories by Wax Immersion
- ASTM-C92 - Standard Test Methods for Sieve Analysis and Water Content of Refractory Materials
- ASTM-C93 - Test Methods for Cold Crushing Strength and Modulus of Rupture of Insulating Firebrick (Withdrawn 1992)
- ASTM-C973 - Standard Practice for Preparing Test Specimens From Basic Refractory Gunning Products by Pressing
- ASTM-C974 - Standard Practice for Preparing Test Specimens from Basic Refractory Castable Products by Casting
- ASTM-C975 - Standard Practice for Preparing Test Specimens from Basic Refractory Ramming Products by Pressing
- ASTM-C987 - Standard Test Method for Vapor Attack on Refractories for Furnace Superstructures
- ASTM-F1097 - Standard Specification for Mortar, Refractory (High-Temperature, Air-Setting)
- ASTM-F1312 - Standard Specification for Brick, Insulating, High Temperature, Fire Clay
BSI:
- BS-1902-10.1 - Methods of testing refractory materials. Investment casting shell mould systems
- BS-1902-10.2 - Methods of testing refractory materials. Investment casting shell mould systems
- BS-1902-11 - Methods of Testing Refractory Materials, Refractory Mortars and Putties
- BS-1902-1A - Methods of testing refractory materials. Sampling and physical tests
- BS-1902-1C - Methods of testing refractory materials. Mouldable and castable refractories
- BS-1902-2.3 - Methods of testing refractory materials. Chemical analysis (wet methods). Chemical analysis of magnesites and dolomites
- BS-1902-3.1 - Methods of testing refractory materials. General and textural properties
- BS-1902-3.10 - Methods of testing refractory materials. General and textural properties
- BS-1902-3.13 - Methods of testing refractory materials. General and textural properties
- BS-1902-3.14 - Methods of testing refractory materials. General and textural properties
- BS-1902-3.19 - Methods of testing refractory materials. General and textural properties. Measurement of dimensions and external defects of refractory bricks. Dimensions and conformity to drawings
- BS-1902-3.3 - Methods of testing refractory materials. General and textural properties
- BS-1902-3-3.4 - Methods of Testing Refractory Materials, General and Texturalproperties, Determination
- BS-1902-3-3.9 - Methods of testing refractory materials. General and textural properties. Determination of permeability to gases (method 1902-309)
- BS-1902-3.4 - Methods of testing refractory materials. General and textural properties. Determination of true density (method 1902-304)
- BS-1902-3.5 - Methods of Testing Refractory Materials, General and Textural Properties, Determination
- BS-1902-3.8 - Methods of testing refractory materials. General and textural properties. Determination of bulk density, true porosity and apparent porosity of dense shaped products (method 1902-308)
- BS-1902-4.0 - Methods of testing refractory materials. Properties measured under an applied stress. Introduction
- BS-1902-4.6 - Methods of testing refractory materials. Properties measured under an applied stress
- BS-1902-5.0 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.11 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.13 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.14 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.3 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.4 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5.5 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-5-5.0 - Methods of testing refractory materials. Refractory and thermal properties.
- BS-1902-5.8 - Methods of testing refractory materials. Refractory and thermal properties
- BS-1902-6 - Methods of testing refractory materials
- BS-1902-7.0 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction. Introduction and definitions
- BS-1902-7.1 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction
- BS-1902-7.2 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction
- BS-1902-7.3 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction
- BS-1902-7.4 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction
- BS-1902-7.5 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction
- BS-1902-7.6 - Methods of testing refractory materials. Unshaped refractories used in monolithic construction. Testing of materials as preformed test pieces
- BS-1902-9.1 - Methods of testing refractory materials. Chemical analysis by instrumental methods Analysis of alumino-silicate refractories by X-ray fluorescence
- BS-1902-9.2 - Methods of testing refractory materials. Chemical analysis by instrumental methods
- BS-1902-9.3 - Methods of testing refractory materials. Chemical analysis by instrumental methods
- BS-3056-1 - Sizes of refractory bricks
- BS-3056-2 - Sizes of refractory bricks
- BS-3056-3 - Sizes of refractory bricks
- BS-3056-4 - Sizes of refractory bricks. Specification for bricks for electric arc furnace roofs
- BS-3056-7 - Sizes of refractory bricks
- BS-3056-8 - Sizes of refractory bricks
- BS-3446-1 - Glossary of terms associated with refractory materials
- BS-3446-2 - Glossary of terms associated with refractory materials
- BS-4966 - Specification for silica refractories for use in coke ovens
- BS-6065 - Methods for sampling and acceptance testing of shaped refractory products
- BS-6434 - Guide to the use of BS 6065 'Methods for sampling and acceptance testing of shaped refractory products'
- BS-6886 - Specification for alumino-silicate refractories for use in coke ovens
- BS-7225-2.1 - Classification of refractories. Unshaped refractory products. Alumina, silica and alumino-silicate products
- BS-7225-2.2 - Classification of refractories. Unshaped refractory products. Basic products
- BS-7225-3.1 - Classification of refractories. Ceramic fibre products. Blankets, mats, felts and paper
- BS-7243-1 - Refractory raw materials. Method of sampling
- BS-EN-1094-1 - Insulating refractory products
- BS-EN-1094-2 - Insulating refractory products
- BS-EN-1094-3 - Insulating refractory products
- BS-EN-1094-6 - Insulating refractory products
- BS-EN-12475-4 - Classification of dense shaped refractory products. Special products
- BS-EN-12698-1 - Chemical analysis of nitride bonded silicon carbide refractories
- BS-EN-12698-2 - Chemical analysis of nitride bonded silicon carbide refractories
- BS-EN-1402-1 - Unshaped refractory products. Introduction and classification
- BS-EN-1402-2 - Unshaped refractory products. Sampling for testing
- BS-EN-1402-3 - Unshaped refractory products. Characterization as received
- BS-EN-1402-4 - Unshaped refractory products. Determination of consistency of castables
- BS-EN-1402-5 - Unshaped refractory products. Preparation and treatment of test pieces
- BS-EN-1402-6 - Unshaped refractory products . Measurement of physical properties
- BS-EN-1402-7 - Unshaped refractory products. Tests on pre-formed shapes
- BS-EN-1402-8 - Unshaped refractory products. Determination of complementary properties
- BS-EN-14945 - Refractory products and materials. Spectrometric determination of chromium (VI) in chrome bearing refractories, before and after use
- BS-EN-993-11 - Methods of test for dense shaped refractory products
- BS-EN-993-12 - Methods of test for dense shaped refractory products
- BS-EN-993-15 - Methods of test for dense shaped refractory products
- BS-EN-993-18 - Methods of test for dense shaped refractory products
- BS-EN-993-19 - Methods of test for dense shaped refractory products
- BS-EN-993-1-TC - Tracked Changes. Methods of test for dense shaped refractory products
- BS-EN-993-2 - Methods of test for dense shaped refractory products
- BS-EN-993-20 - Methods of test for dense shaped refractory products
- BS-EN-993-3 - Methods of test for dense shaped refractory products
- BS-EN-993-6-TC - Tracked Changes. Methods of test for (dense) shaped refractory products
- BS-EN-993-7 - Methods of test for dense shaped refractory products
- BS-EN-993-8 - Methods of Test for Dense Shaped Refractory Products, Determination of Refractoriness-
- BS-EN-993-9 - Methods of test for dense shaped refractory products
- BS-EN-ISO-10058-1 - Chemical analysis of magnesite and dolomite refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-10058-2 - Chemical analysis of magnesite and dolomite refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-10058-3 - Chemical analysis of magnesite and dolomite refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-10081-1 - Classification of dense shaped refractory products
- BS-EN-ISO-10081-2 - Classification of dense shaped refractory products
- BS-EN-ISO-10081-3 - Classification of dense shaped refractory products
- BS-EN-ISO-10081-4 - Classification of dense shaped refractory products
- BS-EN-ISO-12676 - Refractory products. Determination of resistance to carbon monoxide
- BS-EN-ISO-12677 - Chemical analysis of refractory products by X-ray fluorescence (XRF)
- BS-EN-ISO-12680-1 - Methods of test for refractory products
- BS-EN-ISO-14719 - Chemical analysis of refractory material glass and glazes. Determination of Fe2+ and Fe3+ by the spectral photometric method with 1,10-phenanthroline
- BS-EN-ISO-16282 - Methods of test for dense shaped refractory products. Determination of resistance to abrasion at ambient temperature
- BS-EN-ISO-1893 - Refractory products. Determination of refractoriness under load. Differential method with rising temperature
- BS-EN-ISO-1927-1 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-2 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-3 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-4 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-5 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-6 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-7 - Monolithic (unshaped) refractory products
- BS-EN-ISO-1927-8 - Monolithic (unshaped) refractory products
- BS-EN-ISO-20182 - Refractory testpiece preparation. Gunning refractory panels by the pneumatic-nozzle mixing type guns
- BS-EN-ISO-20565-1 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method)
- BS-EN-ISO-20565-2 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method)
- BS-EN-ISO-20565-3 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21068-1 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-1-TC - Tracked Changes. Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-2 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-2-TC - Tracked Changes. Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-3 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-3-TC - Tracked Changes. Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21068-4 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon
- BS-EN-ISO-21078-2 - Determination of boron (III) oxide in refractory products
- BS-EN-ISO-21079-1 - Chemical analysis of refractories containing alumina, zirconia and silica. Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21079-2 - Chemical analysis of refractories containing alumina, zirconia, and silica. Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21079-3 - Chemical analysis of refractories containing alumina, zirconia, and silica. Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21587-1 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21587-2 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-21587-3 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method)
- BS-EN-ISO-26845 - Chemical analysis of refractories. General requirements for wet chemical analysis, atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) methods
- BS-EN-ISO-8894-1 - Refractory materials. Determination of thermal conductivity
- BS-EN-ISO-8895 - Shaped insulating refractory products. Determination of cold crushing strength
- BS-ISO-10081-4 - Classification of dense shaped refractory products
- BS-ISO-10635 - Refractory products. Methods of test for ceramic fibre products.
- BS-ISO-12680-1 - Methods of Test for Refractory Products, Determination of Dynamic Young's Modulus (Moe
- BS-ISO-13765-1 - Refractory mortars
- BS-ISO-13765-2 - Refractory mortars
- BS-ISO-13765-3 - Refractory mortars
- BS-ISO-13765-4 - Refractory mortars
- BS-ISO-13765-5 - Refractory mortars
- BS-ISO-13765-6 - Refractory mortars
- BS-ISO-13765-7 - Refractory mortars
- BS-ISO-16169 - Preparation of silicon carbide and similar materials for analysis by ISO 12677 X-ray fluorescence (XRF). Fused cast-bead method
- BS-ISO-16334 - Monolithic refractory products. Determination of resistance to explosivespalling
- BS-ISO-18886 - Refractory test-piece preparation. Gunning refractory panels by wet gunning techniques
- BS-ISO-21736 - Refractories. Test methods for thermal shock resistance
- BS-ISO-22016 - Determination of sulfur in refractory products and raw materials by gravimetric, photometric and titrimetric methods
- BS-ISO-22605 - Refractories. Determination of dynamic Youngs modulus (MOE) at elevated temperatures by impulse excitation of vibration
- BS-ISO-22685 - Refractory products. Determination of compressive strength at elevated temperature
- BS-ISO-8840 - Refractory materials. Determination of bulk density of granular materials (grain density)
- DD-CEN-993-11 - Dense shaped refractory products
- DD-ENV-1402-1 - Unshaped refractory products. Introduction and definitions
- DD-ENV-1402-2 - Unshaped refractory products
- DD-ENV-1402-3 - Unshaped refractory products. Characterization as received
- DD-ENV-1402-4 - Unshaped refractory products
- DD-ENV-1402-5 - Unshaped refractory products. Preparation and treatment of test pieces
- DD-ENV-1402-6 - Unshaped Refractory Products, Measurement of Physical Properties
- DD-ENV-1402-7 - Unshaped refractory products. Tests for preformed shapes
- DD-ENV-1402-8 - Unshaped refractory products. Determination of complementary properties
- DD-ENV-955-4 - Chemical analysis of refractory products
- DD-ENV-993-11 - Methods of test for dense shaped refractory products
ISO:
- ISO-10059-1 - Dense, shaped refractory products - Determination of cold compressive strength - Part 1: Referee test without packing
- ISO-10059-2 - Dense, shaped refractory products - Determination of cold compressive strength - Part 2: Test with packing
- ISO-10060 - Dense, shaped refractory products - Test methods for products containing carbon
- ISO-10080 - Refractory products - Classification of dense, shaped acid-resisting products
- ISO-10081-1 - Classification of dense shaped refractory products - Part 1: Alumina-silica
- ISO-10081-2 - Classification of dense shaped refractory products - Part 2: Basic products containing less than 7 % residual carbon
- ISO-10081-3 - Classification of dense shaped refractory products - Part 3: Basic products containing from 7 % to 50 % residual carbon
- ISO-10081-4 - Classification of dense shaped refractory products - Part 4: Special products
- ISO-10635 - Refractory products -- Methods of test for ceramic fibre products
- ISO-1109 - Refractory products -- Classification of dense shaped refractory products
- ISO-12676 - Refractory products -- Determination of resistance to carbon monoxide
- ISO-12677 - Chemical analysis of refractory products by X-ray fluorescence (XRF) - Fused cast-bead method
- ISO-12678-1 - Refractory products - Measurement of dimensions and external defects of refractory bricks - Part 1: Dimensions and conformity to drawings
- ISO-12678-2 - Refractory products - Measurement of dimensions and external defects of refractory bricks - Part 2: Corner and edge defects and other surface imperfections
- ISO-12680-1 - Methods of test for refractory products - Part 1: Determination of dynamic Youngs modulus (MOE) by impulse excitation of vibration
- ISO-13765-1 - Refractory mortars - Part 1: Determination of consistency using the penetrating cone method
- ISO-13765-2 - Refractory mortars - Part 2: Determination of consistency using the reciprocating flow table method
- ISO-13765-3 - Refractory mortars - Part 3: Determination of joint stability
- ISO-13765-4 - Refractory mortars - Part 4: Determination of flexural bonding strength
- ISO-13765-5 - Refractory mortars - Part 5: Determination of grain size distribution (sieve analysis)
- ISO-13765-6 - Refractory mortars - Part 6: Determination of moisture content of ready-mixed mortars
- ISO-13765-7 - Refractory mortars - Part 7: Determination of permanent change in dimensions on heating
- ISO-14719 - Chemical analysis of refractory material glass and glazes - Determination of Fe2+ and Fe3+ by the spectral photometric method with 1,10-phenanthroline
- ISO-16169 - Preparation of silicon carbide and similar materials for analysis by ISO 12677 X-ray fluorescence (XRF) - Fused cast-bead method
- ISO-16282 - Methods of test for dense shaped refractory products - Determination of resistance to abrasion at ambient temperature
- ISO-16334 - Monolithic refractory products - Determination of resistance to explosive spalling
- ISO-16349 - Refractory materials - Determination of abrasion resistance at elevated temperature
- ISO-16835 - Refractory products - Determination of thermal expansion
- ISO-18886 - Refractory test-piece preparation - Gunning refractory panels by wet gunning techniques
- ISO-1893 - Refractory products - Determination of refractoriness under load - Differential method with rising temperature
- ISO-1927-1 - Monolithic (unshaped) refractory products - Part 1: Introduction and classification
- ISO-1927-2 - Monolithic (unshaped) refractory products - Part 2: Sampling for testing
- ISO-1927-3 - Monolithic (unshaped) refractory products - Part 3: Characterization as received
- ISO-1927-4 - Monolithic (unshaped) refractory products - Part 4: Determination of consistency of castables
- ISO-1927-5 - Monolithic (unshaped) refractory products - Part 5: Preparation and treatment of test pieces
- ISO-1927-6 - Monolithic (unshaped) refractory products - Part 6: Measurement of physical properties
- ISO-1927-7 - Monolithic (unshaped) refractory products - Part 7: Tests on pre-formed shapes
- ISO-1927-8 - Monolithic (unshaped) refractory products - Part 8: Determination of complementary properties
- ISO-20182 - Refractory test-piece preparation - Gunning refractory panels by the pneumatic-nozzle mixing type guns
- ISO-20565-1 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents, dissolution and determination of gravimetric silica
- ISO-20565-2 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis
- ISO-20565-3 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 3: Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES)
- ISO-21068-1 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 1: General information, terminology and sample preparation
- ISO-21068-2 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 2: Determination of volatile components, total carbon, free carbon, silicon carbide, total and free silicon, free and surface silica
- ISO-21068-3 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituents
- ISO-21068-4 - Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 4: XRD methods
- ISO-21079-1 - Chemical analysis of refractories containing alumina, zirconia and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents and dissolution
- ISO-21079-2 - Chemical analysis of refractories containing alumina, zirconia, and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis
- ISO-21079-3 - Chemical analysis of refractories containing alumina, zirconia, and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method) - Part 3: Flame atomic absorption spectrophotometry (FAAS) and inductively coupled plasma emission spectrometry (ICP -AES)
- ISO-21587-1 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents, dissolution and gravimetric silica
- ISO-21587-2 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis
- ISO-21587-3 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 3: Inductively coupled plasma and atomic absorption spectrometry methods
- ISO-21736 - Refractories - Test methods for thermal shock resistance
- ISO-21828 - Guidance on standards available for preparation and testing of monolithic, unshaped refractory products
- ISO-22016 - Determination of sulfur in refractory products and raw materials by gravimetric, photometric and titrimetric methods
- ISO-2245 - Shaped insulating refractory products - Classification
- ISO-22605 - Refractories - Determination of dynamic Young.s modulus (MOE) at elevated temperatures by impulse excitation of vibration
- ISO-22685 - Refractory products - Determination of compressive strength at elevated temperature
- ISO-23071 - Refractory products - Determination of reduced species in carbon containing refractories by XRD
- ISO-2477 - Shaped insulating refractory products - Determination of permanent change in dimensions on heating
- ISO-2478 - Dense shaped refractory products - Determination of permanent change in dimensions on heating
- ISO-26845 - Chemical analysis of refractories - General requirements for wet chemical analysis, atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) methods
- ISO-3187 - Refractory products - Determination of creep in compression
- ISO-5013 - Refractory products - Determination of modulus of rupture at elevated temperatures
- ISO-5014 - Dense and insulating shaped refractory products - Determination of modulus of rupture at ambient temperature
- ISO-5016 - Shaped insulating refractory products - Determination of bulk density and true porosity
- ISO-5017 - Dense shaped refractory products - Determination of bulk density, apparent porosity and true porosity
- ISO-5018 - Refractory materials - Determination of true density
- ISO-5019-1 - Refractory bricks - Dimensions - Part 1 : Rectangular bricks
- ISO-5019-2 - Refractory bricks - Dimensions - Part 2 : Arch bricks
- ISO-5019-3 - Refractory bricks - Dimensions - Part 3 : Rectangular checker bricks for regenerative furnaces
- ISO-5019-4 - Refractory bricks - Dimensions - Part 4: Dome bricks for electric arc furnace roofs
- ISO-5019-5 - Refractory bricks - Dimensions - Part 5 : Skewbacks
- ISO-5019-6 - Refractory bricks - Dimensions - Part 6: Basic bricks for oxygen steel-making converters
- ISO-5022 - Shaped refractory products - Sampling and acceptance testing
- ISO-528 - Refractory products - Determination of pyrometric cone equivalent (refractoriness)
- ISO-5417 - Refractory bricks for use in rotary kilns - Dimensions
- ISO-836 - Terminology for refractories
- ISO-8656-1 - Refractory products - Sampling of raw materials and unshaped products - Part 1 : Sampling scheme
- ISO-8840 - Refractory materials - Determination of bulk density of granular materials (grain density)
- ISO-8841 - Dense, shaped refractory products - Determination of permeability to gases
- ISO-8890 - Dense shaped refractory products - Determination of resistance to sulfuric acid
- ISO-8894-1 - Refractory materials - Determination of thermal conductivity - Part 1: Hot-wire methods (cross-array and resistance thermometer)
- ISO-8894-2 - Refractory materials - Determination of thermal conductivity - Part 2: Hot-wire method (parallel)
- ISO-8895 - Shaped insulating refractory products - Determination of cold crushing strength
- ISO-9205 - Refractory bricks for use in rotary kilns - Hot-face identification marking
Other SDOs:
- DIN-EN-12698-1 - Part 1: Chemical Methods, Chemical Analysis of Nitride Bonded Silicon Carbide Refracto
- DIN-EN-12698-2 - Part 2: Xrd Methods, Chemical Analysis of Nitride Bonded Silicon Carbide Refractories
- DIN-EN-1402-1 - Unshaped refractory products - Part 1: Introduction and classification; German version EN 1402-1:2003
- DIN-EN-1402-2 - Unshaped refractory products - Part 2: Sampling for testing; German version EN 1402-2:2003
- DIN-EN-1402-3 - Unshaped refractory products - Part 3: Characterization as received; German version EN 1402-3:2003
- DIN-EN-1402-4 - Unshaped refractory products - Part 4: Determination of consistency of castables; German version EN 1402-4:2003
- DIN-EN-1402-5 - Unshaped refractory products - Part 5: Preparation and treatment of test pieces; German version EN 1402-5:2003
- DIN-EN-1402-6 - Unshaped refractory products - Part 6: Measurement of physical properties; German version EN 1402-6:2003
- DIN-EN-1402-7 - Unshaped refractory materials - Part 7: Tests on pre-formed shapes; German version EN 1402-7:2003
- DIN-EN-1402-8 - Unshaped refractory products - Part 8: Determination of complementary properties; German version EN 1402-8:2003
- DIN-EN-14945 - Refractory Products & Materials - Spectrometric Determination of Chromium(VI) in Chrom
- DIN-EN-993-15 - Part 15: Determination of Thermal Conductivity by the Hot-Wire (Parallel) Method, Meth
- DIN-EN-993-2/A1 - Methods of test for dense shaped refractory products - Part 2: Determination of true density; German version EN 993-2:1995/A1:2003
- DIN-EN-ISO-10081-1 - Part 1: Alumina-Silica, Classification of Dense Shaped Refractory Products
- DIN-EN-ISO-10081-2 - Part 2: Basic Products Containing Less Than 7% Residual Carbon, Classification of Dens
- DIN-EN-ISO-10081-3 - Part 3: Basic Products Containing From 7% To 50% Residual Carbon, Classification of De
- DIN-EN-ISO-12677 - Chemical analysis of refractory products by X-ray fluorescence (XRF) - Fused cast-bead method (ISO 12677:2011)
- DIN-EN-ISO-12680-1 - Part 1: Determination of Dynamic Young's Modulus (Moe) by Impulse Excitation of Vibrat
- DIN-EN-ISO-8895 - Shaped Insulating Refractory Products - Determination of Cold Crushing Strength
- EN-1094-1 - Insulating Refractory Products, Terminology, Classification & Methods of Test for Hig
- EN-1402-1 - Part 1: Introduction & Classification, Unshaped Refractory Products
- EN-1402-2 - Part 2: Sampling for Testing, Unshaped Refractory Products
- EN-1402-5 - Part 5: Preparation & Treatment of Test Pieces, Unshaped Refractory Products
- EN-1402-6 - Part 6: Measurement of Physical Properties, Unshaped Refractory Products
- EN-14945 - Refractory Products & Materials - Spectrometric Determination of Chromium(VI) in Chrom
- EN-993-11 - Part 11: Determination of Resistance To Thermal Shock, Methods of Test for Dense Shape
- EN-993-12 - Methods of Test for Dense Shaped Refractory Products, Determination of Pyrometric Cone
- EN-993-15 - Part 15: Determination of Thermal Conductivity by the Hot-Wire (Parallel) Method, Meth
- EN-993-18 - Methods of test for dense shaped refractory products - Part 18: Determination of bulk density of granular materials by the water method with vacuum
- EN-993-19 - Part 19: Determination of Thermal Expansion by a Differential Method, Methods of Test
- EN-993-3 - Methods of Test for Dense Shaped Refractory Products, Test Methods for Carbon-Containi
- EN-993-7 - Determination of Modulus of Rupture at Elevated Temperatures, Methods of Test for Dens
- EN-993-8 - Part 8: Determination of Refractoriness-Under-Load, Methods of Testing Dense Shaped R
- EN-993-9 - Methods of Test for Dense Shaped Refractory Products, Determination of Creep in Compre
- EN-ISO-10058-1 - Part 1: Apparatus, Reagents, Dissolution & Determination of Gravimetric Silica, Chemi
- EN-ISO-10058-2 - Part 2: Wet Chemical Analysis, Chemical Analysis of Magnesites & Dolomites Refractory
- EN-ISO-10058-3 - Part 3: Flame Atomic Absorption Spectrophotometry (Faas) & Inductively Coupled Plasma
- EN-ISO-10081-1 - Part 1: Alumina-Silica, Classification of Dense Shaped Refractory Products
- EN-ISO-10081-2 - Part 2: Basic Products Containing Less Than 7% Residual Carbon, Classification of Dens
- EN-ISO-10081-3 - Part 3: Basic Products Containing From 7% To 50% Residual Carbon, Classification of De
- EN-ISO-10081-4 - Classification of dense shaped refractory products - Part 4: Special products
- EN-ISO-12676 - Refractory Products, Determination of Resistance To Carbon Monoxide
- EN-ISO-12677 - Chemical analysis of refractory products by X-ray fluorescence (XRF) - Fused cast-bead method
- EN-ISO-12680-1 - Part 1: Determination of Dynamic Young's Modulus (Moe) by Impulse Excitation of Vibrat
- EN-ISO-14719 - Chemical analysis of refractory material glass and glazes - Determination of Fe2+ and Fe3+ by the spectral photometric method with 1,10-phenanthroline (ISO 14719:2011)
- EN-ISO-1893 - Refractory Products, Determination of Refractoriness Under Load, Differential Method W
- EN-ISO-1927-1 - Monolithic (unshaped) refractory products - Part 1: Introduction and classification (ISO 1927-1:2012)
- EN-ISO-1927-2 - Monolithic (unshaped) refractory products - Part 2: Sampling for testing (ISO 1927-2:2012)
- EN-ISO-1927-3 - Monolithic (unshaped) refractory products - Part 3: Characterization as received (ISO 1927-3:2012)
- EN-ISO-1927-4 - Monolithic (unshaped) refractory products - Part 4: Determination of consistency of castables (ISO 1927-4:2012)
- EN-ISO-1927-5 - Monolithic (unshaped) refractory products - Part 5: Preparation and treatment of test pieces (ISO 1927-5:2012)
- EN-ISO-1927-6 - Monolithic (unshaped) refractory products - Part 6: Measurement of physical properties (ISO 1927-6:2012)
- EN-ISO-1927-7 - Monolithic (unshaped) refractory products - Part 7: Tests on pre-formed shapes (ISO 1927-7:2012)
- EN-ISO-1927-8 - Monolithic (unshaped) refractory products - Part 8: Determination of complementary properties (ISO 1927-8:2012)
- EN-ISO-20565-1 - Part 1: Apparatus, Reagents, Dissolution & Determination of Gravimetric Silica, Chemi
- EN-ISO-20565-2 - Part 2: Wet Chemical Analysis, Chemical Analysis of Chrome-Bearing Refractory Products
- EN-ISO-20565-3 - Part 3: Flame Atomic Absorption Spectromety (Faas) & Inductively Coupled Plasma Atomic
- EN-ISO-21068-1 - Chemical Analysis of SILCON-Carbide-Containing Raw Materials & Refractory Products, Ge
- EN-ISO-21068-2 - Part 2: Determination of Loss on Ignition, Total Carbon, Free Carbon & Silicon Carbide
- EN-ISO-21068-3 - Part 3: Determination of Nitrogen, Oxygen & Metallic & Oxidic Constituents, Chemical A
- EN-ISO-21078-2 - Determination of Boron (Iii) Oxide in Refractory Products, Acid Extraction Method For
- EN-ISO-21079-1 - Part 1: Apparatus, Reagents & Dissolution, Chemical Analysis of Refractories Containin
- EN-ISO-21079-2 - Chemical Analysis of Refractories Containing Alumina, Zirconia, & Silica, Refractories
- EN-ISO-21079-3 - Chemical Analysis of Refractories Containing Alumina, Zirconia, & Silica, Refractories
- EN-ISO-21587-1 - Chemical Analysis of Aluminosilicate Refractory Products (Alternative To the X-Ray Flu
- EN-ISO-21587-2 - Chemical Analysis of Aluminosilicate Refractory Products (Alternative To the X-Ray Flu
- EN-ISO-21587-3 - Chemical Analysis of Aluminosilicate Refractory Products (Alternative To the X-Ray Flu
- EN-ISO-8894-1 - Part 1: Hot-Wire Methods (Cross-Array & Resistance Thermometer), Refractory Materials
- EN-ISO-8895 - Shaped Insulating Refractory Products - Determination of Cold Crushing Strength
- SIS-CEN/TS-15418 - Methods of test for dense refractory products - Guidelines for testing the corrosion of refractories caused by liquids
- SS-EN-1094-1 - Insulating refractory products - Part 1: Terminology, classification and methods of test for high temperature insulation wool products
- SS-EN-1094-2 - Insulating refractory products - Part 2: Classification of shaped products (ISO 2245:1990 modified)
- SS-EN-1094-3 - Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres
- SS-EN-1094-4 - Insulating refractory products - Part 4: Determination of bulk density and true porosity
- SS-EN-1094-5 - Insulating refractory products - Part 5: Determination of cold crushing strength
- SS-EN-1094-6 - Insulating refractory products - Part 6: Determination of permanent change in dimensions of shaped products on heating (ISO 2477:1987 modified)
- SS-EN-12475-1 - Classification of dense shaped refractory products - Part 1: Alumina-silica products
- SS-EN-12475-2 - Classification of dense shaped refractory products - Part 2: Basic products containing less than 7 % residual carbon
- SS-EN-12475-3 - Classification of dense shaped refractory products - Part 3: Basic products containing 7 % to 30 % residual carbon
- SS-EN-12475-4 - Classification of dense shaped refractory products - Part 4: Special products
- SS-EN-1402-1 - Unshaped refractory products - Part 1: Introduction and classification
- SS-EN-1402-2 - Unshaped refractory products - Part 2: Sampling for testing
- SS-EN-1402-3 - Unshaped refractory products - Part 3: Characterization as received
- SS-EN-1402-4 - Unshaped refractory products - Part 4: Determination of consistency of castables
- SS-EN-1402-5 - Unshaped refractory products - Part 5: Preparation and treatment of test pieces
- SS-EN-1402-6 - Unshaped refractory products - Part 6: Measurement of physical properties
- SS-EN-1402-7 - Unshaped refractory materials - Part 7: Tests on pre-formed shapes
- SS-EN-1402-8 - Unshaped refractory products - Part 8: Determination of complementary properties
- SS-EN-14945 - Refractory products and materials - Spectrometric determination of chromium (VI) in chrome bearing refractories, before and after use
- SS-EN-955-2 - Chemical analysis of refractory products - Part 2: Products containing silica and/or alumina (wet method)
- SS-EN-993-1 - Methods of test for dense shaped refractory products - Part 1: Determination of bulk density, apparent porosity and true porosity
- SS-EN-993-10 - Methods of test for dense shaped refractory products - Part 10: Determination of permanent change in dimensions on heating
- SS-EN-993-11 - Methods of test for dense shaped refractory products - Part 11: Determination of resistance to thermal shock
- SS-EN-993-12 - Methods of test for dense shaped refractory products - Part 12: Determination of pyrometric cone equivalent (refractoriness)
- SS-EN-993-13 - Methods of test for dense shaped refractory products - Part 13: Specification for pyrometric reference cones for laboratory use
- SS-EN-993-14 - Methods of testing dense shaped refractory products - Part 14: Determination of thermal conductivity by the hot wire (cross-array) method
- SS-EN-993-15 - Methods of test for dense shaped refractory products - Part 15: Determination of thermal conductivity by the hot-wire (parallel) method
- SS-EN-993-16 - Dense shaped refractory products - Methods of test - Part 16: Determination of resistance to sulphuric acid
- SS-EN-993-17 - Methods of test for dense shaped refractory products - Part 17: Determination of bulk density of granular materials by the mercury method with vacuum
- SS-EN-993-18 - Methods of test for dense shaped refractory products - Part 18: Determination of bulk density of granular materials by the water method with vacuum
- SS-EN-993-19 - Methods of test for dense shaped refractory products - Part 19: Determination of thermal expansion by a differential method
- SS-EN-993-2 - Methods of test for dense shaped refractory products - Part 2: Determination of true density
- SS-EN-993-20 - Methods of test for dense shaped refractory products - Part 20: Determination of resistance to abrasion at ambient temperature
- SS-EN-993-2-AM1 - Methods of test for dense shaped refractory products - Part 2: Determination of true density
- SS-EN-993-3 - Methods of test for dense shaped refractory products - Part 3: Test methods for carbon-containing refractories
- SS-EN-993-4 - Methods of test for dense shaped refractory products - Part 4: Determination of permeability to gases
- SS-EN-993-5 - Methods of test for dense shaped refractory products - Part 5: Determination of cold crushing strength
- SS-EN-993-6 - Methods of test for (dense) shaped refractory products - Part 6: Determination of modulus of rupture at ambient temperature
- SS-EN-993-7 - Methods of test for dense shaped refractory products - Part 7: Determination of modulus of rupture at elevated temperatures
- SS-EN-993-8 - Methods of test for dense shaped refractory products - Part 8: Determination of refractoriness-under-load
- SS-EN-993-9 - Methods of test for dense shaped refractory products - Part 9: Determination of creep in compression
- SS-EN-ISO-10081-1 - Classification of dense shaped refractory products - Part 1: Alumina-silica (ISO 10081-1:2003)
- SS-EN-ISO-10081-2 - Classification of dense shaped refractory products - Part 2: Basic products containing less than 7% residual carbon (ISO 10081-2:2003)
- SS-EN-ISO-10081-3 - Classification of dense shaped refractory products - Part 3: Basic products containing from 7% to 50% residual carbon (ISO 10081-3:2003)
- SS-EN-ISO-10081-4 - Classification of dense shaped refractory products - Part 4: Special products (ISO 10081-4:2014)
- SS-EN-ISO-12676 - Refractory products - Determination of resistance to carbon monoxide (ISO 12676:2000)
- SS-EN-ISO-12677 - Chemical analysis of refractory products by X-ray fluorescence (XRF) - Fused cast-bead method (ISO 12677:2011)
- SS-EN-ISO-12680-1 - Methods of test for refractory products - Part 1: Determination of dynamic Young's modulus (MOE) by impuls excitation of vibration (ISO 12680-1:2005)
- SS-EN-ISO-14719 - Chemical analysis of refractory material glass and glazes - Determination of Fe2+ and Fe3+ by the spectral photometric method with 1,10-phenantroline (ISO 14719:2011)
- SS-EN-ISO-16282 - Methods of test for dense shaped refractory products - Determination of resistance to abrasion at ambient temperature (ISO 16282:2007)
- SS-EN-ISO-1893 - Refractory products - Determination of refractoriness under load - Differential method with rising temperature (ISO 1893:2007)
- SS-EN-ISO-1927-1 - Monolithic (unshaped) refractory products - Part 1: Introduction and classification (ISO 1927-1:2012)
- SS-EN-ISO-1927-2 - Monolithic (unshaped) refractory products - Part 2: Sampling for testing (ISO 1927-2:2012)
- SS-EN-ISO-1927-3 - Monolithic (unshaped) refractory products - Part 3: Characterization as received (ISO 1927-3:2012)
- SS-EN-ISO-1927-4 - Monolithic (unshaped) refractory products - Part 4: Determination of consistency of castables (ISO 1927-4:2012)
- SS-EN-ISO-1927-5 - Monolithic (unshaped) refractory products - Part 5: Preparation and treatment of test pieces (ISO 1927-5:2012)
- SS-EN-ISO-1927-6 - Monolithic (unshaped) refractory products - Part 6: Measurement of physical properties (ISO 1927-6:2012)
- SS-EN-ISO-1927-7 - Monolithic (unshaped) refractory products - Part 7: Tests on pre-formed shapes (ISO 1927-7:2012)
- SS-EN-ISO-1927-8 - Monolithic (unshaped) refractory products - Part 8: Determination of complementary properties (ISO 1927-8:2012)
- SS-EN-ISO-20182 - Refractory test-piece preparation - Gunning refractory panels by the pneumatic-nozzle mixing type guns (ISO 20182:2008)
- SS-EN-ISO-20565-1 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents, dissolution and determination of gravimetric silica (ISO 20565-1:2008)
- SS-EN-ISO-20565-2 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis (ISO 20565-2:2008)
- SS-EN-ISO-20565-3 - Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) - Part 3: Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) (ISO 20565-3:2008)
- SS-EN-ISO-21068-1 - Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 1: General information and sample preparation (ISO 21068-1:2008)
- SS-EN-ISO-21068-2 - Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 2: Determination of loss on ignition, total carbon, free carbon and silicon carbide, total and free silica and total and free silicon (ISO 21068-2:2008)
- SS-EN-ISO-21068-3 - Chemical analysis of silicon-carbide-containing raw materials and refractory products - Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituents (ISO 21068-3:2008)
- SS-EN-ISO-21079-1 - Chemical analysis of refractories containing alumina, zirconia and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents and dissolution (ISO 21079-1:2008)
- SS-EN-ISO-21079-2 - Chemical analysis of refractories containing alumina, zirconia and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis (ISO 21079-2:2008)
- SS-EN-ISO-21079-3 - Chemical analysis of refractories containing alumina, zirconia, and silica - Refractories containing 5 percent to 45 percent of ZrO2 (alternative to the X-ray fluorenscence method) - Part 3: Flame atomic absorption spectrophotometry (FAAS) and inductively coupled plasma emission spectrometry (ICP-AES) (ISO 21079-3:2008)
- SS-EN-ISO-21587-1 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 1: Apparatus, reagents, dissolution and gravimetric silica (ISO 21587-1:2007)
- SS-EN-ISO-21587-2 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 2: Wet chemical analysis (ISO 21587-2:2007)
- SS-EN-ISO-21587-3 - Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) - Part 3: Inductively coupled plasma and atomic absorption spectrometry methods (ISO 21587-3:2007)
- SS-EN-ISO-26845 - Chemical analysis of refractories - General requirements for wet chemical analysis, atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry methods (ICP-AES) (ISO 26845:2008)
- SS-EN-ISO-8894-1 - Refractory materials - Determination of thermal conductivity - Part 1: Hot-wire methods (cross-array and resistance thermometer) (ISO 8894-1:2010)
- SS-EN-ISO-8895 - Shaped insulating refractory products - Determination of cold crushing strength (ISO 8895:2004)
- SS-ENV-1402-1 - Unshaped refractory products - Part 1: Introduction and definitions
- SS-ENV-1402-2 - Unshaped refractory products - Part 2: Sampling for testing
- SS-ENV-1402-4 - Unshaped refractory products - Part 4: Determination of consistency of castables
- SS-ENV-1402-5 - Unshaped refractory products - Part 5: Preparation and treatment of test pieces
- SS-ENV-820-2 - Advanced technical ceramics - Methods of test formonolithic ceramics - Thermo-mechanical properties - Part 2: Determination of selfloaded deformation