Document Center List of Standards on Plastics And Rubber Insulating Materials Including Adhesive Tapes
ICS Code 29.035.20
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A717 - Standard Test Method for Surface Insulation Resistivity of Single-Strip Specimens
- ASTM-C1710 - Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
- ASTM-C1775 - Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications
- ASTM-D1000 - Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
- ASTM-D1047 - Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable
- ASTM-D1048 - Standard Specification for Rubber Insulating Blankets
- ASTM-D1049 - Standard Specification for Rubber Insulating Covers
- ASTM-D1051 - Standard Specification for Rubber Insulating Sleeves
- ASTM-D1351 - Standard Specification for Thermoplastic Polyethylene Insulation for Electrical Wire and Cable
- ASTM-D1352 - Standard Specification for Ozone-Resisting Butyl Rubber Insulation for Wire and Cable (Withdrawn 2006)
- ASTM-D1389 - Standard Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials (Withdrawn 2014)
- ASTM-D1520 - Specification for Synthetic Rubber Heat-or Moisture-Resisting Insulation for Wire and Cable (Withdrawn 1983)
- ASTM-D1523 - Standard Specification for Synthetic Rubber Insulation for Wire and Cable, 90°C Operation (Withdrawn 2011)
- ASTM-D1673 - Standard Test Methods for Relative Permittivity And Dissipation Factor of Expanded Cellular Polymers Used For Electrical Insulation (Withdrawn 2006)
- ASTM-D1675 - Standard Test Methods for Polytetrafluoroethylene Tubing
- ASTM-D1679 - Standard Specification for Synthetic Rubber Heat-and Moisture-Resisting Insulation for Wire and Cable, 75°C Operation (Withdrawn 2006)
- ASTM-D178 - Standard Specification for Rubber Insulating Matting
- ASTM-D1822 - Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
- ASTM-D1822M - Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials (Withdrawn 1996)
- ASTM-D2148 - Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation
- ASTM-D2219 - Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 60 °C Operation
- ASTM-D2220 - Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 75 °C Operation
- ASTM-D2301 - Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape
- ASTM-D2305 - Standard Test Methods for Polymeric Films Used for Electrical Insulation
- ASTM-D2308 - Standard Specification for Thermoplastic Polyethylene Jacket for Electrical Wire and Cable
- ASTM-D2381 - Standard Test Methods for Flexible Composite Materials Used for Electrical Insulation (Withdrawn 2005)
- ASTM-D2405 - Specification for General-Purpose Acrylonitrile-Buradiene/Poly (Vinyl Chloride) (NBR/PVC) Jacket for Wire and Cable (Withdrawn 1984)
- ASTM-D2432 - Specification for Heavy-Duty Acrylonitrile-Butadienel Poly (Vinyl Chloride) (NBR/PVC) Jacket for Wire and Cable (Withdrawn 1984)
- ASTM-D2484 - Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2020)
- ASTM-D2522 - Standard Test Method for Chlorine Content of Polybutenes Used for Electrical Insulation (Withdrawn 2017)
- ASTM-D2526 - Standard Specification for Ozone-Resisting Silicone Rubber Insulation for Wire and Cable (Withdrawn 2006)
- ASTM-D256 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
- ASTM-D2633 - Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
- ASTM-D2655 - Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 0 to 2000 V, 90 °C Operation
- ASTM-D2656 - Standard Specification for Crosslinked Polyethylene Insulation for Wire and
Cable Rated 2001 to 35 000 V - ASTM-D2686 - Standard Specification for Polytetrafluoroethylene-Backed Pressure-Sensitive Electrical Insulating Tape
- ASTM-D2708 - Specification for Extra-Heavy-Duty Acrylonitrile-Butadiene/Poly (Vinyl Chloride) (NBR/PVC) Jacket for Wire and Cable (Withdrawn 1984)
- ASTM-D2754 - Standard Specification for High-Temperature Glass Cloth Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2022)
- ASTM-D2768 - Standard Specification for General-Purpose Ethylene-Propylene Rubber Jacket for Wire and Cable (Withdrawn 2007)
- ASTM-D2769 - Method of Testing Rubber Hose Used for Liquefied Petroleum Gas Extractable Material (Withdrawn 1986)
- ASTM-D2770 - Standard Specification for Ozone-Resisting Ethylene-Propylene Rubber Integral Insulation and Jacket for Wire and Cable (Withdrawn 2007)
- ASTM-D2802 - Standard Specification for Ozone-Resistant Ethylene-Alkene Polymer Insulation
for Wire and Cable (Withdrawn 2020) - ASTM-D2819 - Specification for Extra-Heavy-Duty Black Polychloroprene Jacket for Wire and Cable (Withdrawn 1984)
- ASTM-D2902 - Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation
- ASTM-D2903 - Standard Specification for Crosslinked Chlorinated Polyolefin Heat-Shrinkable Tubing for Electrical Insulation
- ASTM-D3005 - Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape
- ASTM-D3006 - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2022)
- ASTM-D3144 - Standard Specification for Crosslinked Poly(Vinylidene Fluoride) and Poly(Vinylidene Fluoride) Copolymer Heat-Shrinkable Tubing for Electrical Insulation
- ASTM-D3149 - Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation (Withdrawn 2020)
- ASTM-D3150 - Standard Specification for Crosslinked and Noncrosslinked Poly(Vinyl Chloride) Heat-Shrinkable Tubing for Electrical Insulation
- ASTM-D3390 - Specification for Rubber Semiconducting Tape (Withdrawn 1986)
- ASTM-D3485 - Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)
- ASTM-D350 - Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation
- ASTM-D3554 - Standard Specification for Track-Resistant Black Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation
- ASTM-D3555 - Standard Specification for Track-Resistant Black Crosslinked Polyethylene Insulation for Wire and Cable, 90 °C Operation
- ASTM-D3664 - Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022)
- ASTM-D4089 - Specification for Heavy Duty Chlorinated Polyethylene (CPE) Jacket for Wire and Cable (Withdrawn 1985)
- ASTM-D4090 - Specification for Heavy Duty Chlorinated Polyethylene (CPE) Jacket for Wire and Cable (Withdrawn 1985)
- ASTM-D4091 - Specification for Extra-Heavy-Duty Black Chlorinated Polyethylene (CPE) Jacket for Wire and Cable (Withdrawn 1986)
- ASTM-D4244 - Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Acrylonitrile-Butadiene/Poly(Vinyl Chloride) (NBR/PVC) Jackets for Wire and Cable (Withdrawn 2007)
- ASTM-D4245 - Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation For Wire and Cable, 90 °C Dry/75 °C Wet Operation
- ASTM-D4246 - Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation For Wire and Cable, 90°C Operation
- ASTM-D4247 - Standard Specification for General-Purpose, Black Heavy-Duty, and Black Extra-Heavy-Duty Crosslinked Polychloroprene Jackets for Wire and Cable (Withdrawn 2006)
- ASTM-D4313 - Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorinated Polyethylene (CPE) Jackets For Wire and Cable
- ASTM-D4314 - Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets For Wire and Cable (Withdrawn 2017)
- ASTM-D4325 - Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
- ASTM-D4363 - Standard Specification for Thermoplastic Chlorinated Polyethylene (CPE) Jacket for Wire and Cable
- ASTM-D4388 - Standard Specification for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
- ASTM-D4514 - Standard Specification for Friction Tape (Withdrawn 2020)
- ASTM-D4568 - Standard Test Methods for Evaluating Compatibility Between Cable Filling and Flooding Compounds And Polyolefin Wire and Cable Materials
- ASTM-D4652 - Standard Specification for Silicone Liquid Used for Electrical Insulation
- ASTM-D5213 - Standard Specification for Polymeric Resin Film for Electrical Insulation and Dielectric Applications
- ASTM-D5214 - Test Method for Polyimide Resin Film for Electrical Insulation and Dielectric Aplication (Withdrawn 1995)
- ASTM-D532 - Specification for Natural Rubber Jacket for Wire and Cable (Withdrawn 1996)
- ASTM-D6096 - Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 90 °C Operation
- ASTM-D6097 - Standard Test Method for Relative Resistance to Vented Water-Tree Growth in Solid Dielectric Insulating Materials
- ASTM-D618 - Standard Practice for Conditioning Plastics for Testing
- ASTM-D6272 - Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
- ASTM-D69 - Standard Test Methods for Friction Tapes
- ASTM-D710 - Standard Specification for Vulcanized Fibre Sheets, Rods, and Tubes Used for Electrical Insulation
- ASTM-D754 - Specification for Synthetic Rubber Insulation for Wire and Cable (Withdrawn 1983)
- ASTM-D755 - Specification for Synthetic Rubber Insulation for Wire and Cable (Withdrawn 1983)
- ASTM-D7793 - Standard Specification for Insulated Vinyl Siding
- ASTM-D785 - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
- ASTM-D790 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
- ASTM-D876 - Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
- ASTM-D922 - Standard Specification for Nonrigid Vinyl Chloride Polymer Tubing
- ASTM-E2769 - Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading
- ASTM-F1236 - Standard Guide for Visual Inspection of Electrical Protective Rubber Products
- ASTM-F1837M - Standard Specification for Heat-Shrink Cable Entry Seals (Metric)
BSI:
- BS-3816 - Specification for epoxy resin casting systems used for electrical insulating applications at power frequencies
- BS-3924 - Specification for pressure-sensitive adhesive tapes for electrical insulating purposes
- BS-5067-3-3.1 - Rubber latices. Methods of test. Determination of mechanical stability of natural rubber latex concentrate
- BS-5664-2.1 - Solventless polymerisable resinous compounds used for electrical insulation. Methods of test. Materials other than coating powders
- BS-5734-2 - Polyester Moulding Compounds for Electrical & Other Purposes, Specification for Dough
- BS-5734-4 - Polyester Moulding Compounds for Electrical & Other Purposes, Specification for Sheet
- BS-6234 - Specification for polyethylene insulation and sheath of electric cables
- BS-6469-4-2 - Insulating and sheathing materials of electric cables. Methods of test specific to polyethylene and polypropylene compounds. Elongation at break after pre-conditioning. Wrapping test after pre-conditioning. Wrapping test after thermal ageing in air. Measurement of mass increase. Long-term stability test. Test method for copper-catalysed oxidative degradation
- BS-6746 - Specification for PVC insulation and sheath of electric cables
- BS-6893-3-116-TO-118 - Flexible insulating sleeving for electrical purposes. Specification for requirements for individual types of sleeving. General purpose extruded polychloroprene
- BS-6893-3-121-&-122 - Flexible insulating sleeving for electrical purposes. Specification for requirements for individual types of sleeving. Extruded silicone sleeving
- BS-6893-3.209 - Flexible insulating sleeving for electrical purposes. Specification for requirements for individual types of sleeving. General purpose heat-shrinkable sleeving, flame retarded polyolefin shrink ratio 2:1
- BS-6893-3-420-TO-422 - Flexible insulating sleeving for electrical purposes. Specification for requirements for individual types of sleeving. Polyethylene terephthalate textile with acrylic based coating
- BS-7655-10.1 - Specification for insulating and sheathing materials for cables
- BS-7655-1.1 - Specification for insulating and sheathing materials for cables. Elastomeric insulating compounds
- BS-7655-11.1 - Specification for Insulating and Sheathing Materials for Cables, Miscellaneous Insulatin
- BS-7655-1.2 - Specification for insulating and sheathing materials for cables
- BS-7655-12.1 - Specification for insulating and sheathing materials for cables. Miscellaneous sheathing compounds
- BS-7655-12.2 - Specification for Insulating and Sheathing Materials for Cables, Miscellaneous Sheathing
- BS-7655-1.3 - Specification for insulating and sheathing materials for cables. Elastomeric insulating compounds
- BS-7655-1.4 - Specification for insulating and sheathing materials for cables. Elastomeric insulating compounds
- BS-7655-1.5 - Specification for insulating and sheathing materials for cables
- BS-7655-1.6 - Specification for insulating and sheathing materials for cables. Elastomeric insulating compounds
- BS-7655-2.1 - Harmonized Types
- BS-7655-2.3 - Specification for insulating and sheathing materials for cables. Elastomeric sheathing compounds
- BS-7655-2.4 - Specification for insulating and sheathing materials for cables. Elastomeric sheathing compounds. Welding cable covering
- BS-7655-2.6 - Specification for insulating and sheathing materials for cables
- BS-7655-3.1 - Specification for Insulating and Sheathing Materials for Cables, Pvc Insulating Compound
- BS-7655-3.2 - Specification for insulating and sheathing materials for cables. PVC insulating compounds
- BS-7655-4.1 - Specification for insulating and sheathing materials for cables. PVC sheathing compounds
- BS-7655-4.2 - Specification for insulating and sheathing materials for cables. PVC sheathing compounds
- BS-7655-4.3 - Special Applications - Fr Cables
- BS-7655-5.1 - Specification for Insulating & Sheathing Materials for Cables, Cross-Linked Insulating
- BS-7655-5-5.1 - Specification for Insulating & Sheathing Materials for Cables, Cross-Linked Insulating
- BS-7655-6.1 - Specification for insulating and sheathing materials for cables
- BS-7655-8.1 - Harmonized Types
- BS-7816-1 - Determination of long-term radiation ageing in polymers
- BS-7816-2 - Determination of long-term radiation ageing in polymers. Procedures for predicting ageing at low dose rates
- BS-7878-1 - Materials used in communication cables
- BS-7878-2 - CENELEC Hd 624.2 S1Pvc Sheathing Compounds
- BS-7878-3 - CENELEC Hd 624.3 S1Pe Insulation
- BS-7878-5 - Materials used in communication cables
- BS-7878-7 - Materials used in communication cables
- BS-7933-1 - Electric cables. Accessories. Material characterisation. Fingerprinting and type tests for resinous compounds
- BS-7933-2 - Electric cables. Accessories. Material characterisation. Fingerprinting and type tests for heat shrinkable components for low voltage applications
- BS-7933-3 - Electric cables. Accessories. Material characterisation. Fingerprinting for heat shrinkable components for medium voltage applications from 3,6/6 (7,2) kV up to 20,8/36 (42) kV
- BS-7933-4 - Electric cables. Accessories. Material characterisation. Fingerprinting for cold shrinkable components for low and medium voltage applications up to 20,8/36 (42) kV
- BS-7970 - Electric cables. Metal foil and longitudinally welded aluminium sheath constructions of power cables having XLPE insulation for rated voltages from 66 kV (Um = 72.5 kV) to 132 kV (Um = 145 kV)
- BS-921 - Specification. Rubber mats for electrical purposes
- BS-EN-4840-001 - Aerospace series. Heat shrinkable moulded shapes
- BS-EN-4840-002 - Aerospace series. Heat shrinkable moulded shapes
- BS-EN-50200 - Method of test for resistance to fire of unprotected small cables for use in emergency circuits
- BS-EN-50200-TC - Tracked Changes. Method of test for resistance to fire of unprotected small cables for use in emergency circuits
- BS-EN-50214-TC - Tracked Changes. Flat flexible cables
- BS-EN-50290-2-21 - Communication cables
- BS-EN-50290-2-23 - Communication cables
- BS-EN-50290-2-24 - Communication cables
- BS-EN-50290-2-25 - Communication cables
- BS-EN-50290-2-26 - Communication cables
- BS-EN-50290-2-27 - Communication cables
- BS-EN-50290-2-28 - Communication cables. Common design rules and construction
- BS-EN-50290-2-29 - Communication cables
- BS-EN-50290-2-29-TC - Tracked Changes. Communication cables
- BS-EN-50290-2-30 - Communication cables. Common design rules and construction
- BS-EN-50290-2-35 - Communication cables
- BS-EN-50290-2-36 - Communication cables
- BS-EN-50290-2-37 - Communication cables
- BS-EN-50290-2-38 - Communication cables
- BS-EN-50363-1 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-10-1 - Insulating, sheathing and covering materials for low-voltage energy cables
- BS-EN-50363-10-2 - Insulating, sheathing and covering materials for low-voltage energy cables
- BS-EN-50363-2-1 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-2-2 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-3 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-4-1 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-4-2 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-5 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-6 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-7 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-8 - Insulating, sheathing and covering materials for low voltage energy cables
- BS-EN-50363-9-1 - Insulating, sheathing and covering materials for low-voltage energy cables
- BS-EN-50414 - Test methods for analysis of lead in PVC taken from insulation and sheath of electric and optical fibre cables. Method A: Total lead content determination with flame excitation atomic absorption spectrometry. Method B: Qualitative analysis of lead by lead sulphide staining
- BS-EN-50497 - Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables
- BS-EN-50655-1 - Electric cables. Accessories. Material characterization
- BS-EN-50655-1-TC - Tracked Changes. Electric cables. Accessories. Material characterization.Fingerprinting for resinous compounds.
- BS-EN-50655-2 - Electric cables. Accessories. Material characterization
- BS-EN-50655-3 - Electric cables. Accessories. Material characterization
- BS-EN-60454-2 - Pressure-sensitive adhesive tapes for electrical purposes
- BS-EN-60454-3-1 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-10 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials. Requirements for cellulose-acetate-butyrate film tapes with rubber thermosetting adhesive
- BS-EN-60454-3-11 - Pressure-sensitive adhesive tapes for electrical purposes
- BS-EN-60454-3-12 - Pressure-sensitive adhesive tapes for electrical purposes
- BS-EN-60454-3-14 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-15 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-16 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-17 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-18 - Specifications for pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-2 - Pressure-sensitive adhesive tapes for electrical purposes
- BS-EN-60454-3-4 - Pressure-sensitive adhesive tapes for electrical purposes
- BS-EN-60454-3-8 - Pressure-sensitive adhesive tapes for electrical purposes. Specifications for individual materials
- BS-EN-60454-3-9 - Cellulose Acetate Woven Fabric Tapes With Rubber Thermosetting Adhesive
- BS-EN-60674-1 - Specification for plastic films for electrical purposes. Definitions and general requirements
- BS-EN-60674-2 - Specification for plastic films for electrical purposes
- BS-EN-60674-3-1 - Plastic films for electrical purposes
- BS-EN-60674-3(4-6) - Specification for plastic films for electrical purposes. Specifications for individual materials
- BS-EN-60674-3-8 - Plastic films for electrical purposes
- BS-EN-60684-3-100 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-116 - Flexible insulating sleeving
- BS-EN-60684-3-116&11 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-121-12 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN60684-3-121-124 - Specification for Flexible Insulating Sleeving, Specification Requirements For
- BS-EN-60684-3-123, - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving. Extruded silicone sleeving, general purpose
- BS-EN-60684-3-145 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-205 - Flexible insulating sleeving
- BS-EN-60684-3-209 - Flexible insulating sleeving
- BS-EN-60684-3-211 - Flexible insulating sleeving
- BS-EN-60684-3-212 - Flexible insulating sleeving
- BS-EN-60684-3-214 - Flexible insulating sleeving
- BS-EN-60684-3-216 - Flexible insulating sleeving
- BS-EN-60684-3-233 - Flexible insulating sleeving
- BS-EN-60684-3-240-24 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-246 - Flexible insulating sleeving
- BS-EN-60684-3-247 - Flexible insulating sleeving
- BS-EN-60684-3-248 - Flexible insulating sleeving. Specifications for individual types of sleeving
- BS-EN-60684-3-271 - Flexible insulating sleeving
- BS-EN-60684-3-272 - Part 3: Sheet 272: Heat-Shrinkable Elastomer Sleeving, Flameretarded, Fluid Resistant
- BS-EN-60684-3-280 - Flexible insulating sleeving
- BS-EN-60684-3-283 - Flexible insulating sleeving
- BS-EN-60684-3-284 - Flexible insulating sleeving
- BS-EN-60684-3-285 - Flexible insulating sleeving
- BS-EN-60684-3-320 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-340-34 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-343-34 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-406-40 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN-60684-3-420-42 - Specification for flexible insulating sleeving. Specification requirements for individual types of sleeving
- BS-EN60684-3-420-422 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- BS-EN-60811-2-1 - Insulating and sheathing materials of electric cables. Common test methods. Methods specific to elastomeric compounds. Methods specific to elastomeric compounds. Ozone resistance, hot set and mineral oil immersion tests
- BS-EN-60811-3-1 - Insulating and sheathing materials of electric cables. Common test methods. Methods specific to PVC compounds. Pressure test at high temperature. Tests for resistance to cracking
- BS-EN-60811-3-2 - Insulating and sheathing materials of electric cables. Common test methods. Methods specific to PVC compounds. Loss of mass test. Thermal stability test
- BS-EN-60811-4-1 - Insulating and sheathing materials of electric and optical cables. Common test methods
- BS-EN-60811-4-2 - Insulating and sheathing materials of electric and optical cables. Common test methods
- BS-EN-60893-3-1 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes
- BS-EN-60893-3-2 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes
- BS-EN-60893-3-4 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes
- BS-EN-60893-3-5 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes
- BS-EN-60893-3-6 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes. Specifications for individual materials. Requirements for rigid laminated sheets based on silicone resins
- BS-EN-61086-2 - Coatings for loaded printed wire boards (conformal coatings)
- BS-EN-61086-3-1 - Coatings for loaded printed wire boards (conformal coatings)
- BS-EN-61212-2 - Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes
- BS-EN-62011-1 - Insulating materials. Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes
- BS-EN-62011-2 - Insulating materials. Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes
- BS-EN-62011-3-1 - Insulating materials. Industrial rigid moulded laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes
- BS-EN-62329-1 - Heat shrinkable moulded shapes
- BS-EN-62329-2 - Heat shrinkable moulded shapes
- BS-EN-IEC-60674-3-1 - Plastic films for electrical purposes
- BS-EN-IEC-60674-3-1-TC - Tracked Changes. Plastic films for electrical purposes
- BS-EN-IEC-60674-3-2 - Specification for plastic films for electrical purposes
- BS-EN-IEC-60674-3-3 - Plastic films for electrical purposes
- BS-EN-IEC-60674-3-3-TC - Tracked Changes. Plastic films for electrical purposes
- BS-EN-IEC-60674-3-4 - Plastic films for electrical purposes
- BS-EN-IEC-60674-3-7 - Plastic films for electrical purposes
- BS-EN-IEC-60674-3-7-TC - Tracked Changes. Plastic films for electrical purposes
- BS-EN-IEC-60684-3-116-TC - Tracked Changes. Flexible insulating sleeving
- BS-EN-IEC-60684-3-214 - Flexible insulating sleeving
- BS-EN-IEC-60684-3-216 - Flexible insulating sleeving
- BS-EN-IEC-60684-3-247 - Flexible insulating sleeving
- BS-EN-IEC-60684-3-280 - Flexible insulating sleeving
- BS-EN-IEC-60684-3-283 - Flexible insulating sleeving
- BS-EN-IEC-60893-3-6 - Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes
- BS-EN-IEC-62677-1 - Heat shrinkable low and medium voltage moulded shapes
- BS-EN-IEC-62677-2 - Heat shrinkable low and medium voltage moulded shapes
- BS-EN-IEC-62677-3-101 - Heat-shrinkable low and medium voltage moulded shapes
- BS-EN-IEC-62677-3-102 - Heat-shrinkable low and medium voltage moulded shapes
- BS-EN-IEC-62677-3-103 - Heat-shrinkable low and medium voltage moulded shapes
- BS-IEC-60674-2 - Specification for plastic films for electrical purposes. Methods of test
- PD-IEC-61244-1 - Determination of long-term radiation ageing in polymers
- PD-IEC-61956 - Methods of test for the evaluaion of water treeing in insulating materials
- PD-IEC-62039 - Selection guidelines for polymeric materials for outdoor use under HV stress
IEC:
- IEC-1068-1 - Specification for polyester fibre woven tapes - Part 1: Definitions, designation and general requirements
- IEC-1068-3-1 - Polyester fibre woven tapes - Part 3: Specifications for individual materials - Sheet 1: Tapes woven on conventional or shuttleless looms
- IEC-454-1 - Specifications for pressure-sensitive adhesive tapes for electrical purposes - Part 1: General requirements
- IEC-60454-2 - Pressure-sensitive adhesive tapes for electrical purposes - Part 2: Methods of test
- IEC-60454-3-1 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: PVC film tapes with pressure-sensitive adhesive
- IEC-60454-3-11 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 11: Polyester film combinations with glass filament, creped cellulosic paper, polyester non-woven, epoxy and pressure-sensitive adhesive
- IEC-60454-3-1-1 - Amendment 1
- IEC-60454-3-12 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 12: Requirements for polyethylene and polypropylene film tapes with pressure sensitive adhesive
- IEC-60454-3-14 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 14: Polytetrafluoroethylene film tapes with pressure-sensitive adhesive
- IEC-60454-3-15 - Part 3: Specifications for Individual Materials - Sheet 15:Polyester Film/Polyester Non-
- IEC-60454-3-16 - Sheet 16: Polyester Film/Glass Filament Combinations With Pressure-Sensitive Adhesive, Par
- IEC-60454-3-17 - Part 3: Specifications for Individual Materials - Sheet 17:Polyester/Epoxy Combinations
- IEC-60454-3-18 - Sheet 18: Polypropylene Film Tapes With Pressure-Sensitive Adhesive, Part 3: Specification
- IEC-60454-3-19 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 19: Tapes made from various backing materials with pressure-sensitive adhesive on both sides
- IEC-60454-3-2 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for polyester film tapes with rubber thermosetting, rubber thermoplastic or acrylic crosslinked adhesives
- IEC-60454-3-3 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes - Part 3: Specifications Fo
- IEC-60454-3-4 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 4: Cellulose paper, creped and non-creped, with rubber thermosetting adhesive
- IEC-60454-3-5 - Pressure-Sensitive Adhesive Tapes for Electric Purposes - Part 3: Specification for Indivi
- IEC-60454-3-6 - Pressure-Sensitive Adhesive Tapes for Electrical Puposes - Part 3: Specifications for Indi
- IEC-60454-3-7 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 7: Polyimide film tapes with pressure-sensitive adhesive
- IEC-60454-3-8 - Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 8 - Woven fabric tapes with pressure-sensitive adhesive based on glass, cellulose acetate alone or combined with viscose fibre
- IEC-60454-3-9 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes -Part 3: Specification for Indi
- IEC-60674-2 - Specification for plastic films for electrical purposes - Part 2: Methods of test
- IEC-60674-2-AM1 - Amendment 1 - Specification for plastic films for electrical purposes - Part 2: Methods of test
- IEC-60674-3-1 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- IEC-60674-3-1-AM1 - Amendment 1 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- IEC-60674-3-1-RL - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- IEC-60674-3-2 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation
- IEC-60674-3-3 - Plastic films for electrical purposes - Part 3:Specifications for individual materials - Sheet 3: Polycarbonate (PC) films used for electrical insulation
- IEC-60674-3-4 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheets 4: Polyimide films used for electrical insulation
- IEC-60674-3-7 - Plastic films for electrical purposes - Part 3: Specifications for individual materials . Sheet 7: Fluoroethylene-propylene (FEP) films used for electrical insulation
- IEC-60674-3-8 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation
- IEC-60674-3-8-AM1 - Amendment 1 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation
- IEC-60684-1 - Flexible insulating sleeving - Part 1: Definitions and general requirements
- IEC-60684-2-1 - Amendment 1: Flexible Insulating Sleeving - Part 2: Methods of Test
- IEC-60684-2-2 - Amendment 2: Flexible Insulating Sleeving - Part 2: Methods of Test
- IEC-60684-3-100 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 100 to 105: Extruded PVC sleeving
- IEC-60684-3-116 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose
- IEC-60684-3-116-117 - Sheets 116 & 117: Extruded Polychloroprene - General Purpose, Part 3: Specifications for I
- IEC-60684-3-116-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose
- IEC-60684-3-121 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 121 to 124: Extruded silicone sleeving
- IEC-60684-3-136 - Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 136: Extruded fluorosilicone sleeving - General purpose
- IEC-60684-3-145 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 145 to 147: Extruded PTFE sleeving
- IEC-60684-3-151 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 151: Extruded PVC/nitrile rubber - General purpose
- IEC-60684-3-165 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving
- IEC-60684-3-205 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 205: Heat-shrinkable chlorinated polyolefin sleeving, flame retarded, nominal shrink ratio 1,7:1 and 2:1
- IEC-60684-3-209 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 209: Heat-shrinkable, polyolefin sleeving, general purpose, flame retarded
- IEC-60684-3-211 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1
- IEC-60684-3-212 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 212: Heat-shrinkable polyolefin sleevings
- IEC-60684-3-213 - Sheet 213: Heat-Shrinkable Polyolefin Sleeving, Not Flame Retarded, Shrink Ratio 2:1, Part
- IEC-60684-3-214 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
- IEC-60684-3-214-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
- IEC-60684-3-216 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame- retarded, limited-fire-hazard sleeving
- IEC-60684-3-216-1 - Amendment 1 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame retarded, limited-fire-hazard sleeving
- IEC-60684-3-216-2 - Amendment 2 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame-retarded, limited-fire-hazard sleeving
- IEC-60684-3-216-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame- retarded, limited-fire-hazard sleeving
- IEC-60684-3-217 - Part 3: Specifications for Individual Types of Sleeving - S217: Heat-Shrinkable Polyolefin
- IEC-60684-3-218 - Part 3: Specifications for Individual Types of Sleeving - Sheet 218: Heat-Shrinkable Pol
- IEC-60684-3-228 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1
- IEC-60684-3-229 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 229: Heat-shrinkable semi-flexible, polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1
- IEC-60684-3-233 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 233: Heat-shrinkable fluoroelastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1
- IEC-60684-3-240-243 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 240 to 243: Heat-shrinkable PTFE sleeving
- IEC-60684-3-246 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 246: Heat-shrinkable polyolefin sleeving, dual wall, non-flame retarded
- IEC-60684-3-247 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall
- IEC-60684-3-247-AM1 - Amendment 1 - Flexible insulating sleeving - Part 3 Specifications for individual types of sleeving - Sheet 247 : Heatshrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall
- IEC-60684-3-247-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable, polyolefin sleeving, dual wall, not flame retarded, thick and medium wall
- IEC-60684-3-248 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 248: General purpose, heat-shrinkable, dual wall polyolefin sleeving, flame retarded, shrink ratios 2:1, 3:1, 4:1
- IEC-60684-3-271 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleevings, flame retarded, fluid resistant, shrink ratio 2:1
- IEC-60684-3-272 - Part 3: Specifications for Individual Types of Sleeving - Sheet 272: Heat-Shrinkable Ela
- IEC-60684-3-280 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving, anti-tracking
- IEC-60684-3-280-AM1 - Amendment 1 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving, anti-tracking
- IEC-60684-3-280-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving, anti-tracking
- IEC-60684-3-281 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 281: Heat-shrinkable, polyolefin sleeving, semiconductive
- IEC-60684-3-282 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control
- IEC-60684-3-283 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation
- IEC-60684-3-283-AM1 - Amendment 1 - Flexible insulating sleeving - Partie 3:Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation
- IEC-60684-3-283-RL - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation
- IEC-60684-3-284 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 284: Heat-shrinkable sleevings, for oil barrier applications
- IEC-60684-3-285 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 285: Heat-shrinkable polyolefin sleeving, for medium voltage joint insulation
- IEC-60684-3-300 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 300: Glass textile fibre sleeving, braided, uncoated
- IEC-60684-3-320 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 320: Polyethylene terephthalate textile sleeving, lightly impregnated
- IEC-60684-3-340-342 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 340 to 342: Expandable braided polyethylene terephthalate textile sleeving
- IEC-60684-3-343-345 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 343 to 345: Expandable braided ethylene chlorotrifluoroethylene (E-CTFE) textile sleeving, uncoated
- IEC-60684-3-400-402 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 400 to 402: Glass textile sleeving with silicone elastomer coating
- IEC-60684-3-403-405 - Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheets 403 to 405: Glass textile sleeving with acrylic based coating
- IEC-60684-3-406-408 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 406 to 408: Glass textile sleeving with PVC coating
- IEC-60684-3-409 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 409: Glass textile sleeving with polyurethane (PUR)-based coating
- IEC-60684-3-420-422 - Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheets 420 to 422: Polyethylene terephthalate textile sleeving with acrylic based coating
- IEC-60811-2-1 - Part 2-1: Methods Specific To Elastomeric Compounds - Ozoneresistance, Hot Set & Mineral
- IEC-61086-1 - Coatings for loaded printed wire boards (conformal coatings) - Part 1: Definitions, classification and general requirements
- IEC-61086-2 - Coatings for loaded printed wire boards (conformal coatings) - Part 2: Methods of test
- IEC-61086-3-1 - Coatings for loaded printed wire boards (conformal coatings) - Part 3-1: Specifications for individual materials - Coatings for general purpose (Class 1), high reliability (Class 2) and aerospace (Class 3)
- IEC-62011-1 - Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements
- IEC-62011-2 - Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test
- IEC-62011-3-1 - Insulating materials - Industrial rigid moulded laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes - Part 3-1: Specifications for individual materials - Tubes and rods of rectangular and hexagonal cross-section
- IEC-62039 - Selection guidelines for polymeric materials for outdoor use under HV stress
- IEC-62329-1 - Part 1: Definitions & General Requirements, Heat Shrinkable Moulded Shapes
- IEC-62329-2 - Heat-shrinkable moulded shapes - Part 2: Methods of test
- IEC-62677-1 - Heat shrinkable low and medium voltage moulded shapes - Part 1: General requirements
- IEC-62677-2 - Heat shrinkable low and medium voltage moulded shapes - Part 2: Methods of test
- IEC-62677-3-101 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications
- IEC-62677-3-102 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications
- IEC-62677-3-103 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 103: Heat-shrinkable, polyolefin, conductive moulded shapes for medium voltage applications
- IEC-648 - Method of test for coefficients of friction of plastic film and sheeting for use as electrical insulation
- IEC-674-1 - Specification for plastic films for electrical purposes. Part 1: Definitions and general requirements
- IEC-674-3-2 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation
- IEC-674-3-3 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Requirements for polycarbonate (PC) films used for electrical insulation
- IEC-674-3-4 TO 6 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheets 4 to 6: Requirements for polyimide films used for electrical insulation
- IEC-674-3-7 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 7: Requirements for fluoroethylene-propylene (FEP) films used for electrical insulation
Other SDOs:
- EN-50200 - Method of test for resistance to fire of unprotected small cables for use in emergency circuits
- EN-50290-2-21 - Communication cables - Part 2-21: Common design rules and construction - PVC insulation compounds
- EN-50290-2-23 - Communication cables - Part 2-23: Common design rules and construction - Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables
- EN-50290-2-24 - Communication Cables, Common Design Rules & Construction, Pe Sheathing
- EN-50290-2-25 - Communication cables - Part 2-25: Common design rules and construction - Polypropylene insulation compounds
- EN-50290-2-26 - Halogen Free Flame Retardant Insulation Compounds
- EN-50290-2-27 - Communication cables - Part 2-27: Common design rules and construction - Halogen free flame retardant thermoplastic sheathing compounds
- EN-50290-2-28 - Communication Cables, Common Design Rules & Construction, Filling Compound for Filled
- EN-50290-2-29 - Communication cables - Part 2-29: Common design rules and construction - Crosslinked polyethylene insulation compounds: instrumentation, control and field bus cables
- EN-50290-2-30 - Poly(TETRAFLUO-ROETHYLENE-Hexafluoropropylene) (Fep) Insulation & Sheathing
- EN-50290-2-35 - Communication cables - Part 2-35: Common design rules and construction - Polyamide sheathing compound
- EN-50290-2-36 - Communication cables - Part 2-36: Common design rules and construction - Crosslinked Silicone rubber insulation compound
- EN-50290-2-37 - Communication cables - Part 2-37: Common design rules and construction - Polyethylene insulation for coaxial cables
- EN-50290-2-38 - Communication cables - Part 2-38: Common design rules and construction - Polypropylene insulation for coaxial cables
- EN-50363-2-1 - Insulating, sheathing and covering materials for low voltage energy cables - Part 2-1: Cross-linked elastomeric sheathing compounds
- EN-50363-2-1-A1 - Insulating, sheathing and covering materials for low voltage energy cables - Part 2-1: Cross-linked elastomeric sheathing compounds
- EN-50363-3 - Insulating, sheathing and covering materials for low voltage energy cables - Part 3: PVC insulating compounds
- EN-50363-3-A1 - Insulating, sheathing and covering materials for low voltage energy cables - Part 3: PVC insulating compounds
- EN-50363-5 - Insulating, sheathing and covering materials for low voltage energy cables - Part 5: Halogen-free, cross-linked insulating compounds
- EN-50363-5-A1 - Insulating, sheathing and covering materials for low voltage energy cables - Part 5: Halogen-free, cross-linked insulating compounds
- EN-50363-8 - Insulating, sheathing and covering materials for low voltage energy cables - Part 8: Halogen-free, thermoplastic sheathing compounds
- EN-50363-8-A1 - Insulating, sheathing and covering materials for low voltage energy cables - Part 8: Halogen-free, thermoplastic sheathing compounds
- EN-50497 - Recommended Test Method for Assessment of the Risk of Plasticizer Exudation From Pvc I
- EN-50525-2-11 - Electric cables - Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) - Part 2-11: Cables for general applications - Flexible cables with thermoplastic PVC insulation
- EN-60454-2 - Pressure-Sensitive Adhesives Tapes for Electrical Purposes, Methods of Test
- EN-60454-3-11 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes, Specifications for Individu
- EN-60454-3-12 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes, Specifications for Individu
- EN-60454-3-2 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes, Specifications for Individu
- EN-60454-3-4 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes, Specifications for Individu
- EN-60454-3-8 - Pressure-Sensitive Adhesive Tapes for Electrical Purposes, Specifications for Individu
- EN-60454-3-9 - Cellulose Acetate Woven Fabric Tapes With Rubber Thermosetting Adhesive
- EN-60674-1 - Specification for Plastic Films for Electrical Purposes, Definitions & General Require
- EN-60674-2 - Specification for plastic films for electrical purposes - Part 2: Methods of test
- EN-60674-3-1 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors
- EN-60674-3(4-6) - Requirements for Polyimide Films Used for Electrical Insulation
- EN-60674-3-8 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation
- EN-60684-3-116 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheets 116 and 117: Extruded polychloroprene, general purpose
- EN-60684-3-116&117 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-60684-3-121-124 - Specification for Flexible Insulating Sleeving, Specification Requirements For
- EN-60684-3-211 - Flexible Insulating Sleeving, Specifications for Individual Types of Sleeving, Heat-S
- EN-60684-3-214 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
- EN-60684-3-216 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 216: Heat-shrinkable, flame-retarded, limited-fire hazard sleeving
- EN-60684-3-233 - Heat-Shrinkable Fluoroelastomer Sleeving, Flame Retarded, Fluid Resistant, Shrink Rati
- EN-60684-3-246 - Flexible Insulating Sleeving, Specifications for Individual Types of Sleeving, Heat-S
- EN-60684-3-247 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 247: Heat-shrinkable polyolefin sleeving, dual wall, not flame retarded, thick and medium wall
- EN-60684-3-248 - Flexible Insulating Sleeving, Specifications for Individual Types of Sleeving, Genera
- EN-60684-3-271 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 271: Heat-shrinkable elastomer sleevings, flame retarded, fluid resistant, shrink ratio 2:1
- EN-60684-3-280 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving, anti-tracking
- EN-60684-3-283 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving, for bus-bar insulation
- EN-60684-3-284 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 284: Heat-shrinkable, sleevings, for oil barrier applications
- EN-60684-3-285 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 285: Heat-shrinkable polyolefin sleeving, for medium voltage joint insulation
- EN-60684-3-320 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-60684-3-340-342 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-60684-3-343-345 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-60684-3-406-408 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-60684-3-420-422 - Specification for Flexible Insulating Sleeving, Specification Requirements for Individ
- EN-61086-2 - Coatings for Loaded Printed Wire Boards (Conformal Coatings), Methods of Test
- EN-61212-2 - Insulating Materials, Industrial Rigid Round Laminated Tubes & Rods Based on Thermoset
- EN-62011-1 - Insulating Materials, Industrial, Rigid, Moulded, Laminatedtubes & Rods of Rectangul
- EN-62011-2 - Insulating Materials, Industrial, Rigid, Moulded, Laminated Tubes & Rods of Rectangul
- EN-62011-3-1 - Insulating Materials, Industrial, Rigid, Moulded, Laminated Tubes & Rods of Rectangul
- EN-62329-1 - Heat Shrinkable Moulded Shapes, Definitions & General Requirements
- EN-62329-2 - Heat Shrinkable Moulded Shapes, Methods of Test
- EN-IEC-60674-3-2 - Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation (IEC 60674-3-2:2019)
- EN-IEC-62677-1 - Heat shrinkable low and medium voltage moulded shapes - Part 1: General requirements
- EN-IEC-62677-2 - Heat shrinkable low and medium voltage moulded shapes - Part 2 Methods of test
- EN-IEC-62677-3-103 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 103: Heat-shrinkable, polyolefin, conductive moulded shapes for medium voltage applications (IEC 62677-3-103:2019)
- JIS-C-2161 - Test methods of coating powders for electrical insulation
- JIS-C-2318 - Balanced biaxially oriented polyethylene terephthalate films used for electrical purposes
- JIS-C-2336 - Pressure-sensitive polyvinyl chloride tapes for electrical purposes
- SS-EN-4840-001 - Aerospace series - Heat shrinkable moulded shapes - Part 001: Technical specification
- UNE-EN-50200 - Method of test for resistance to fire of unprotected small cables for use in emergency circuits
- UNE-EN-50290-2-20 - Communication cables - Part 2-20: Common design rules and construction - General
- UNE-EN-50290-2-37 - Communication cables - Part 2-37: Common design rules and construction - Polyethylene insulation for coaxial cables
- UNE-EN-50290-2-38 - Communication cables - Part 2-38: Common design rules and construction - Polypropylene insulation for coaxial cables