Document Center List of Standards on Flow In Closed Conduits Gas Meters In Buildings, See 91.140.40 Water Meters In Buildings, See 91.140.60
ICS Code 17.120.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-D3464 - Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer
- ASTM-D3764 - Standard Practice for Validation of the Performance of Process Stream Analyzer Systems
- ASTM-D4409 - Standard Test Method for Velocity Measurements of Water in Open Channels with Rotating Element Current Meters (Withdrawn 2023)
- ASTM-D5090 - Standard Practice for Standardizing Ultrafiltration Permeate Flow Performance Data
- ASTM-D5540 - Standard Practice for Flow Control and Temperature Control for On-Line Water Sampling and Analysis
- ASTM-D6888 - Standard Test Method for Available Cyanides with Ligand Displacement and Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection
- ASTM-D7808 - Standard Practice for Determining the Site Precision of a Process Stream Analyzer on Process Stream Material
- ASTM-D8000 - Standard Practice for Flow Conditioning of Natural Gas and Liquids
BSI:
- BS-1042-1-1.2 - Measurement of fluid flow in closed conduits. Pressure differential devices. Specification for square-edged orifice plates and nozzles (with drain holes, in pipes below 50 mm diameter, as inlet and outlet devices) and other orifice plates
- BS-1042-1.4 - Guide To the Use of Devices Specified in Sections 1.1 and 1.2,, Measurement of Fluid Flo
- BS-1042-2.1 - Measurement of fluid flow in closed conduits. Velocity area methods. Method using Pitot static tubes
- BS-1042-2.2 - Measurement of fluid flow in closed conduits. Velocity area methods. Method of measurement of velocity at one point of a conduit of circular cross section
- BS-1042-2.3 - Measurement of fluid flow in closed conduits. Velocity area methods
- BS-1042-2.4 - Measurement of fluid flow in closed conduits. Velocity area methods. Method of measurement of clean water flow using current meters in full conduits and under regular flow conditions
- BS-3680-11A - Methods of Measurement
- BS-3680-11B - Specification for Performance and Installation of Equipmentfor Measurement of Free Su
- BS-5728-2 - Part 2: Specification for Installation Requirements for Meters, Measurement of Flow of Col
- BS-5728-2-S-1 - Supplement 1: Parallel & Multiple Meter Operation, Part 2: Specification for Installation
- BS-5728-3 - Part 3: Methods for Determining Principal Characteristics Ofsingle Mechanical Water Meter
- BS-5728-4 - Measurement of flow of cold potable water in closed conduits
- BS-5728-5 - Part 5: Specification for Installation Requirements for Combination Meters, Measurement Of
- BS-5728-6 - Part 6: Test Methods for Combination Meters, Measurement of Flow of Cold Potable Wate
- BS-5728-7 - Part 7: Specification for Single Mechanical Type Meters
- BS-5857-1.1 - Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow. General
- BS-5857-1.2 - Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow. Constant rate injection method using non-radioactive tracers
- BS-5857-1.3 - Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow. Constant rate injection method using radioactive tracers
- BS-5857-1.4 - Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow. Transit time method using non-radioactive tracers
- BS-5857-1.5 - Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow. Transit time method using radioactive tracers
- BS-7405 - Guide to selection and application of flowmeters for the measurement of fluid flow in closed conduits
- BS-7965 - Guide to the selection, installation, operation and calibration of diagonal path transit time ultrasonic flowmeters for industrial gas applications
- BS-8452 - Use of clamp-on (externally mounted) ultrasonic flow-metering techniques for fluid applications. Guide
- BS-EN-12261 - Gas meters.Turbine gas meters
- BS-EN-13220 - Flow-metering devices for connection to terminal units of medical gas pipeline systems
- BS-EN-16211 - Ventilation for buildings. Measurement of air flows on site. Methods
- BS-EN-29104 - Measurement of fluid flow in closed conduits. Methods of evaluating the performance of electromagnetic flow-meters for liquids
- BS-EN-ISO-20456 - Measurement of fluid flow in closed conduits. Guidance for the use of electromagnetic flowmeters for conductive liquids
- BS-EN-ISO-5167-2 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- BS-EN-ISO-5167-3 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- BS-EN-ISO-5167-4 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- BS-EN-ISO-5167-5 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- BS-EN-ISO-5167-6 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- BS-EN-ISO-9300 - Measurement of gas flow by means of critical flow nozzles
- BS-ISO-10790 - Measurement of fluid flow in closed conduits. Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
- BS-ISO-12242 - Measurement of fluid flow in closed conduits. Ultrasonic transit-time meters for liquid
- BS-ISO-12764 - Measurement of fluid flow in closed conduits. Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full
- BS-ISO-12764-TC - Tracked Changes. Measurement of fluid flow in closed conduits. Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full
- BS-ISO-14511 - Measurement of fluid flow in closed conduits. Thermal mass flowmeters
- BS-ISO-15377 - Measurement of Fluid Flow by Means of Pressure Differential Devices, Guidelins for Sp
- BS-ISO-2186 - Fluid flow in closed conduits. Connections for pressure signal transmissions between primary and secondary elements
- BS-ISO-24062 - Measurement of fluid flow in closed conduits. Clamp-on ultrasonic transit-time meters for liquids and gases
- BS-ISO-24460 - Measurement of fluid flow rate in closed conduits. Radioactive tracer methods
- BS-ISO-3354 - Measurement of clean water flow in closed conduits. Velocity-area method using current-meters in full conduits and under regular flow conditions
- BS-ISO-3966 - Measurement of fluid flow in closed conduits. Velocity area method using Pitot static tubes
- BS-ISO-4064-2 - Measurement of water flow in closed conduits. Meters for cold potable water
- BS-ISO-5168 - Measurement of fluid flow. Procedures for the evaluation of uncertainties
- BS-ISO-7194 - Measurement of fluid flow in closed conduits. Velocity-area methods of flow measurement in swirling or asymmetric flow conditions in circular ducts by means of current-meters or Pitot statics tubes
- BS-ISO-7858-1 - Measurement of Water Flow in Closed Conduits, Combination Meters for Cold Potable Wate
- BS-ISO-7858-2 - Measurement of Water Flow in Closed Conduits, Combination Meters for Cold Potable Wate
- BS-ISO-9464 - Guide To the Use of ISO-5167-1
- PD-ISO-11583 - Measurement of wet gas flow by means of pressure differential devices inserted in circular cross-section conduits
- PD-ISO-12767 - Measurement of fluid flow by means of pressure differential devices. Guidelines on the effect of departure from the specifications and operating conditions given in ISO 5167
- PD-ISO-12767-TC - Tracked Changes. Measurement of fluid flow by means of pressure differential devices. Guidelines on the effect of departure from the specifications and operating conditions given in ISO 5167
- PD-ISO-15377 - Measurement of fluid flow by means of pressure-differential devices. Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167 series
- PD-ISO-15377-TC - Tracked Changes. Measurement of fluid flow by means of pressure-differential devices. Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167
- PD-ISO-3313 - Measurement of fluid flow in closed conduits. Guidelines on the effects of flow pulsations on flow-measurement instruments
- PD-ISO-3313-TC - Tracked Changes. Measurement of fluid flow in closed conduits. Guidelines on the effects of flow pulsations on flow-measurement instruments
- PD-ISO-9464 - Guidelines for the use of ISO 5167:2022
- PD-ISO-9464-TC - Tracked Changes. Guidelines for the use of ISO 5167:2022
- PD-ISO-9824 - Hydrometry. Measurement of free surface flow in closed conduits
- PD-ISO/IEC-30148 - Internet of things (IoT). Application of sensor network for wireless gas meters
IEC:
ISO:
- ISO-10790 - Measurement of fluid flow in closed conduits - Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
- ISO-10790-1 - Measurement of fluid flow in closed conduits - Coriolis mass flowmeters - Amendment 1: Guidelines for gas measurement
- ISO-11583 - Measurement of wet gas flow by means of pressure differential devices inserted in circular cross-section conduits
- ISO-11631 - Measurement of fluid flow - Methods of specifying flowmeter performance
- ISO-12242 - Measurement of fluid flow in closed conduits - Ultrasonic transit-time meters for liquid
- ISO-12764 - Measurement of fluid flow in closed conduits - Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full
- ISO-12765 - Measurement of fluid flow in closed conduits -- Methods using transit-time ultrasonic flowmeters
- ISO-12767 - Measurement of fluid flow by means of pressure differential devices - Guidelines on the effect of departure from the specifications and operating conditions given in ISO 5167
- ISO-13359 - Measurement of conductive liquid flow in closed conduits - Flanged electromagnetic flowmeters - Overall length
- ISO-14164 - Stationary source emissions -- Determination of the volume flowrate of gas streams in ducts -- Automated method
- ISO-14511 - Measurement of fluid flow in closed conduits - Thermal mass flowmeters
- ISO-15377 - Measurement of fluid flow by means of pressure-differential devices - Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167 series
- ISO-17089-1 - Measurement of fluid flow in closed conduits - Ultrasonic meters for gas - Part 1: Meters for custody transfer and allocation measurement
- ISO-17089-2 - Measurement of fluid flow in closed conduits - Ultrasonic meters for gas - Part 2: Meters for industrial applications
- ISO-20456 - Measurement of fluid flow in closed conduits - Guidance for the use of electromagnetic flowmeters for conductive liquids
- ISO-2186 - Fluid flow in closed conduits - Connections for pressure signal transmissions between primary and secondary elements
- ISO-24062 - Measurement of fluid flow in closed conduits - Clamp-on ultrasonic transit-time meters for liquids and gases
- ISO-24460 - Measurement of fluid flow rate in closed conduits - Radioactive tracer methods
- ISO-2975-1 - Measurement of water flow in closed conduits - Tracer methods - Part 1: General
- ISO-2975-2 - Measurement of water flow in closed conduits - Tracer methods - Part 2: Constant rate injection method using non-radioactive tracers
- ISO-2975-3 - Measurement of water flow in closed conduits - Tracer methods - Part 3: Constant rate injection method using radioactive tracers
- ISO-2975-6 - Measurement of water flow in closed conduits - Tracer methods - Part 6: Transit time method using non-radioactive tracers
- ISO-2975-7 - Measurement of water flow in closed conduits - Tracer methods - Part 7: Transit time method using radioactive tracers
- ISO-3313 - Measurement of fluid flow in closed conduits - Guidelines on the effects of flow pulsations on flow-measurement instruments
- ISO-3354 - Measurement of clean water flow in closed conduits - Velocity-area method using current-meters in full conduits and under regular flow conditions
- ISO-3966 - Measurement of fluid flow in closed conduits - Velocity area method using Pitot static tubes
- ISO-4006 - Measurement of fluid flow in closed conduits - Vocabulary and symbols
- ISO-4185 - Measurement of liquid flow in closed conduits - Weighing method
- ISO-5167-1 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements
- ISO-5167-2 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates
- ISO-5167-3 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles
- ISO-5167-4 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes
- ISO-5167-5 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 5: Cone meters
- ISO-5167-6 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 6: Wedge meters
- ISO-5168 - Measurement of fluid flow - Procedures for the evaluation of uncertainties
- ISO-6817 - Measurement of conductive liquid flow in closed conduits - Method using electromagnetic flowmeters
- ISO-7066-2 - Assessment of uncertainty in the calibration and use of flow measurement devices - Part 2 : Non-linear calibration relationships
- ISO-7194 - Measurement of fluid flow in closed conduits - Velocity-area methods of flow measurement in swirling or asymmetric flow conditions in circular ducts by means of current-meters or Pitot static tubes
- ISO-8316 - Measurement of liquid flow in closed conduits - Method by collection of the liquid in a volumetric tank
- ISO-9104 - Measurement of fluid flow in closed conduits - Methods of evaluating the performance of electromagnetic flow-meters for liquids
- ISO-9300 - Measurement of gas flow by means of critical flow nozzles
- ISO-9368-1 - Measurement of liquid flow in closed conduits by the weighing method - Procedures for checking installations - Part 1: Static weighing systems
- ISO-9464 - Guidelines for the use of ISO 5167:2022
- ISO-9824 - Hydrometry - Measurement of free surface flow in closed conduits
- ISO-9951 - Measurement of gas flow in closed conduits - Turbine meters
Other SDOs:
- DIN-EN-12261 - Gas Meters - Turbine Gas Meters
- DIN-EN-ISO-9300 - Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles
- EN-12261 - Gas Meters, Turbine Gas Meters
- EN-13220 - Flow Metering Devices for Connection To Terminal Units of Medical Gas Pipeline Systems
- EN-16211 - Ventilation for buildings - Measurement of air flows on site - Methods
- EN-ISO-5167-5 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 5: Cone meters
- EN-ISO-9300 - Measurement of Gas Flow by Means of Critical Flow, Venturi Nozzles
- JIS-B-7554 - Electromagnetic flowmeters
- JIS-B-7555 - Method of flow measurement by coriolis meters (mass flow, density and volume flow measurement)
- JIS-B-7556 - Procedures of calibration and testing for gas flowmeter
- SS-3471 - Measurement of water flow in closed conduits - Meters for cold potab water - Part 1: Specification
- SS-EN-12261 - Gas meters - Turbine gas meters
- SS-EN-12261-AM1 - Gas meters - Turbine gas meters
- SS-EN-13220 - Flow-metering devices for connection to terminal units of medical gas pipeline systems
- SS-EN-16211 - Ventilation for buildings - Measurement of air flows on site - Methods
- SS-EN-24006 - Measurement of fluid flow in closed conduits - Vocabulary and symbols (ISO 4006:1991)
- SS-EN-24185 - Measurement of liquid flow in closed conduits - Weighing method (ISO 4185:1980)
- SS-EN-29104 - Measurement of fluid flow in closed conduits - Methods of evaluating the performance of electromagnetic flow-meters (ISO 9104:1991)
- SS-EN-ISO-15002 - Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO 15002:2008)
- SS-EN-ISO-15002-AM1 - Flow-metering devices for connection to terminal units of medical gas pipeline systems - Amendment 1 (ISO 15002:2008/Amd 1:2018)
- SS-EN-ISO-20456 - Measurement of fluid flow in closed conduits - Guidance for the use of electromagnetic flowmeters for conductive liquids (ISO 20456:2017)
- SS-EN-ISO-5167-1 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2022)
- SS-EN-ISO-5167-1-AM1 - Measurement of fluid flow by means of pressure differential devices - Part 1: Orifice plates, nozles and Venturi tubes inserted in circular cross-section conduits running full (ISO 5167-1:1995/Amd 1:1998)
- SS-EN-ISO-5167-2 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2022)
- SS-EN-ISO-5167-3 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2022)
- SS-EN-ISO-5167-4 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes (ISO 5167-4:2022)
- SS-EN-ISO-5167-5 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 5: Cone meters (ISO 5167-5:2022)
- SS-EN-ISO-5167-6 - Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 6: Wedge meters (ISO 5167-6:2022)
- SS-EN-ISO-6817 - Measurement of conductive liquid flow in closed conduits - Method using electromagnetic flowmeters (ISO 6817:1995)
- SS-EN-ISO-8316 - Measurement of liquid flow in closed conduits - Method by collection of the liquid in a volumetric tank (ISO 8316:1987)
- SS-EN-ISO-9300 - Measurement of gas flow by means of critical flow nozzles (ISO 9300:2022)
- SS-ISO-14164 - Stationary source emissions - Determination of the volume flowrate of gas streams in ducts - Automated metho
- SS-ISO-4064-2 - Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 1: Specification for the loose-fill products before installation