Document Center List of Standards on Limits And Fits
ICS Code 17.040.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
BSI:
- BS-1916-1 - Limits and fits for engineering
- BS-1916-2 - Limits and fits for engineering
- BS-1916-3 - Limits and fits for engineering
- BS-2856 - Precise conversion of inch and metric sizes on engineering drawings
- BS-4500 - Limits and fits. Guidance for system of cone (taper) fits and tolerances for cones from C = 1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm
- BS-4500-1 - ISO limits and fitsGeneral, tolerances and deviations
- BS-4500A - ISO limits and fits. Data sheet: selected ISO fits - hole basis
- BS-4500B - ISO limits and fits. Data sheet: selected ISO fits - shaft basis
- BS-969 - Specification for limits and tolerances on plain limit gauges
- BS-EN-20286-1 - ISO System of Limits & Fits, ISO System of Limits & Fits, Bases of Tolerances, Deviati
- BS-EN-20286-2 - ISO system of limits and fits
- BS-EN-ISO-1101 - Geometrical product specifications (GPS). Geometrical tolerancing. Tolerances of form, orientation, location and run-out
- BS-EN-ISO-14405-1 - Geometrical product specifications (GPS). Dimensional tolerancing
- BS-EN-ISO-14405-1-TC - Tracked Changes. Geometrical product specifications (GPS). Dimensional tolerancing
- BS-EN-ISO-14405-2 - Geometrical product specifications (GPS). Dimensional tolerancing
- BS-EN-ISO-14405-3 - Geometrical product specifications (GPS). Dimensional tolerancing
- BS-EN-ISO-1938-1 - Geometrical product specifications (GPS). Dimensional measuring equipment
- BS-EN-ISO-1938-2 - Geometrical product specifications (GPS). Dimensional measuring equipment
- BS-EN-ISO-286-1 - Geometrical product specifications (GPS). ISO code system for tolerances on linear sizes
- BS-EN-ISO-286-2 - Geometrical product specifications (GPS). ISO code system for tolerances on linear sizes
- BS-EN-ISO-5458-TC - Tracked Changes. Geometrical product specifications (GPS). Geometrical tolerancing. Pattern and combined geometrical specification
- BS-EN-ISO-5459 - Geometrical product specifications (GPS). Geometrical tolerancing. Datums and datum systems
- BS-EN-ISO-8062-1 - Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts
- BS-EN-ISO-8062-3 - Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts
- BS-ISO-5459 - Technical drawings. Geometrical tolerancing. Datums and datum-systems for geometrical tolerances
- BS-ISO-8062-4 - Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts
- BS-ISO-8062-4-TC - Tracked Changes. Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts
ISO:
- ISO-1101 - Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out
- ISO-13920 - Welding - General tolerances for welded constructions - Dimensions for lengths and angles, shape and position
- ISO-14405-1 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
- ISO-14405-2 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes
- ISO-14405-3 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 3: Angular sizes
- ISO-16570 - Geometrical Product Specifications (Gps) - Linear and Angular Dimensioning and Tolerancin
- ISO-1829 - Selection of tolerance zones for general purposes
- ISO-1938 - ISO system of limits and fits - Part II : Inspection of plain workpieces
- ISO-1938-1 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Plain limit gauges of linear size
- ISO-1938-2 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges
- ISO-2768-1 - General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- ISO-2768-2 - General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications
- ISO-286-1 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits
- ISO-286-2 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ISO-5458 - Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification
- ISO-5459 - Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems
- ISO-8062 - Castings - System of dimensional tolerances and machining allowances
- ISO-8062-1 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary
- ISO-8062-2 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 2: Rules
- ISO-8062-3 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions
- ISO-8062-4 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system
Other SDOs:
- EN-20286-1 - ISO System of Limits & Fits, ISO System of Limits & Fits, Bases of Tolerances, Deviati
- EN-ISO-1101 - Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out
- EN-ISO-14405-1 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
- EN-ISO-14405-2 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011)
- EN-ISO-1938-2 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges
- EN-ISO-286-1 - Part 1: Basis of Tolerances, Deviations & Fits, Geometrical Product Specification (Gp
- EN-ISO-286-2 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (ISO 286-2:2010)
- EN-ISO-5459 - Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems
- EN-ISO-8062-1 - Geometrical Product Specifications (Gps), Dimensional & Geometrical Tolerances for Mou
- EN-ISO-8062-3 - Geometrical Product Specifications (Gps), Dimensional & Geometrical Tolerances for Mou
- JIS-B-0021 - Geometrical product specification (GPS) -- Geometrical tolerancing -- Tolerancing of form, orientation, location and run-out
- JIS-B-0025 - Technical drawings -- Geometrical tolerancing -- Positional tolerancing
- JIS-B-0026 - Technical drawings -- Dimensioning and tolerancing -- Non-rigid parts
- JIS-B-0401-1 - ISO system of limits and fits - Part 1: Bases of tolerances, deviations and fits
- JIS-B-0401-2 - ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts
- JIS-B-0418 - Machining allowance for open die forgings
- SIS-ISO/TR-23605 - Technical product specification (TPS) - Application guidance - International model for national implementation
- SIS-ISO/TS-8062-2 - Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 2: Rules (ISO/TS 8062-2:2013 Corrected version 2013-11-01, IDT)
- SMS-Rapport-37 - Form- och lägetoleranser - Mätning och mätdon (exklusive SS 2650)
- SMS-Rapport-41 - Form- och lägetoleranser - Toleransvärden och ritningsexempel
- SMS-Rapport-43 - Form- och lägetoleranser - Sammanfattning av utgivna och kommande publikationer
- SS-EN-10243-1 - Steel die forgings - Tolerances on dimensions - Part 1: Drop and vertical press forgings
- SS-EN-10243-2 - Steel die forgings - Tolerances on dimensions - Part 2: Upset forgings made on horizontal forging machines
- SS-EN-13001-2 - Crane safety - General design - Part 2: Load actions
- SS-EN-20286-1 - ISO system of limits and fits - Part 1: Bases of tolerances, deviations and fits (ISO 286-1:1988)
- SS-EN-20286-2 - ISO systems of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts (ISO 286-2:1988)
- SS-EN-22768-1 - General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)
- SS-EN-22768-2 - General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989)
- SS-EN-ISO-1101 - Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
- SS-EN-ISO-12180-1 - Geometrical product specifications (GPS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form (ISO 12180-1:2011)
- SS-EN-ISO-12180-2 - Geometrical product specifications (GPS) - Cylindricity - Part 2: Specification operators (ISO 12180-2:2011)
- SS-EN-ISO-12181-1 - Geometrical product specifications (GPS) - Roundness - Part 1: Vocabulary and parameters of roundness (ISO 12181-1:2011)
- SS-EN-ISO-12181-2 - Geometrical product specifications (GPS) - Roundness - Part 2: Specification operators (ISO 12181-2:2011)
- SS-EN-ISO-12780-1 - Geometrical product specifications (GPS) - Straightness - Part 1: Vocabulary and parameters of straightness (ISO 12780-1:2011)
- SS-EN-ISO-12780-2 - Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO 12780-2:2011)
- SS-EN-ISO-12781-1 - Geometrical product specifications (GPS) - Flatness - Part 1: Vocabulary and parameters of flatness (ISO 12781-1:2011)
- SS-EN-ISO-12781-2 - Geometrical product specifications (GPS) - Flatness - Part 2: Specification operators (ISO 12781-2:2011)
- SS-EN-ISO-13920 - Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:2023)
- SS-EN-ISO-14253-2 - Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification (ISO 14253-2:2011)
- SS-EN-ISO-14405-1 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)
- SS-EN-ISO-14405-2 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018)
- SS-EN-ISO-14405-3 - Geometrical product specifications (GPS) - Dimensional tolerancing - Part 3: Angular sizes (ISO 14405-3:2016)
- SS-EN-ISO-1660 - Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing (ISO 1660:2017)
- SS-EN-ISO-16610-1 - Geometrical product specifications (GPS) - Filtration - Part 1: Overview and basic concepts (ISO 16610-1:2015)
- SS-EN-ISO-17450-4 - Geometrical product specifications (GPS) - Basic concepts - Part 4: Geometrical characteristics for quantifying GPS deviations (ISO 17450-4:2017)
- SS-EN-ISO-1938-1 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Plain limit gauges of linear size (ISO 1938-1:2015)
- SS-EN-ISO-1938-2 - Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges (ISO 1938-2:2017)
- SS-EN-ISO-286-1 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Bases of tolerances, deviations and fits (ISO 286-1:2010)
- SS-EN-ISO-286-2 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (ISO 286-2:2010)
- SS-EN-ISO-5458 - Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)
- SS-EN-ISO-5459 - Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO 5459:2011)
- SS-EN-ISO-7083 - Technical product documentation - Symbols used in technical product documentation - Proportions and dimensions (ISO 7083:2021)
- SS-EN-ISO-8062-1 - Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary (ISO 8062-1:2007)
- SS-EN-ISO-8062-3 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023)
- SS-ISO-10578 - Technical drawings - Tolerancing of orientation and location - Projected tolerance zone (ISO 10578:1992, IDT)
- SS-ISO-1101 - Geometrical Product Specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out
- SS-ISO-1803-1 - Building construction - Tolerances - Vocabulary -Part 1: General terms
- SS-ISO-1803-2 - Tolerances for building - Vocabulary - Part 2: Derived terms
- SS-ISO-2768-1 - General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- SS-ISO-2768-2 - General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications
- SS-ISO-286-1 - ISO system of limits and fits - Part 1: Bases of tolerances, deviations and fits
- SS-ISO-3443-5 - Building construction - Tolerances for building -Part 5: Series or values to be used for specification of tolerances
- SS-ISO-4291 - Methods for the assessment of departure from roundness - Measurement of variations in radius
- SS-ISO-4292 - Methods for the assessment of departure from roundness - Measurement by two- and three-point methods
- SS-ISO-5459 - Technical drawings - Geometrical tolerancing - Datums and Datum-systems for geometrical tolerances
- SS-ISO-6318 - Measurements of roundness - Terms, definitions and parameters of roundness
- SS-ISO-7083 - Technical drawings - Symbols for geometrical tolerancing - Proportions and dimensions
- SS-ISO-7737 - Tolerances for building - Presentation of dimensional accuracy data
- SS-ISO-8062 - Castings - System of dimensional tolerances and machining allowances
- SS-ISO-8062-4 - Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 4: General tolerances for castings using profile tolerancing in a general datum system (ISO 8062-4:2017, IDT)
- SS-ISO-8788 - Aerospace - Nuts, metric - Tolerances of form and position