ASTM-E354 › Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 These test methods cover the chemical analysis of high-temperature, electrical, magnetic, and other similar iron, nickel, and cobalt alloys having chemical compositions within the following limits:
| Element | Concentration Range, % | ||
| Aluminum | 0.005 | to | 18.00 |
| Beryllium | 0.001 | to | 0.05 |
| Boron | 0.001 | to | 1.00 |
| Calcium | 0.002 | to | 0.05 |
| Carbon | 0.001 | to | 1.10 |
| Chromium | 0.10 | to | 33.00 |
| Cobalt | 0.10 | to | 75.00 |
| Columbium (Niobium) | 0.01 | to | 6.0 |
| Copper | 0.01 | to | 10.00 |
| Iron | 0.01 | to | 85.00 |
| Magnesium | 0.001 | to | 0.05 |
| Manganese | 0.01 | to | 3.0 |
| Molybdenum | 0.01 | to | 30.0 |
| Nickel | 0.10 | to | 84.0 |
| Nitrogen | 0.001 | to | 0.20 |
| Phosphorus | 0.002 | to | 0.08 |
| Silicon | 0.01 | to | 5.00 |
| Sulfur | 0.002 | to | 0.10 |
| Tantalum | 0.005 | to | 10.0 |
| Titanium | 0.01 | to | 5.00 |
| Tungsten | 0.01 | to | 18.00 |
| Vanadium | 0.01 | to | 3.25 |
| Zirconium | 0.01 | to | 2.50 |
1.2 The test methods in this standard are contained in the sections indicated below:
| Sections | |
| Aluminum, Total, by the 8-Quinolinol Gravimetric Method (0.20 to7.00 %) | 100 |
| Carbon,Total, by the Combustion-Thermal Conductivity Method | 1a |
| Carbon, Total, by the Combustion Gravimetric Method (0.05 to1.10 %) | 79 |
| Chromium by the Atomic Absorption Method (0.006 to 1.00 %) | 165 |
| Chromium by the Peroxydisulfate Oxidation-Titration Method(0.10 to 33.00 %) | 175 |
| Chromium by the Peroxydisulfate-Oxidation Titrimetric Method | 1b |
| Cobalt by the Ion-Exchange-Potentiometric Titration Method (2 to75 %) | 53 |
| Cobalt by the Nitroso-R-Salt Photometric Method (0.10 to 5.0 %) | 61 |
| Copper by Neocuproine Photometric Method (0.01 to 10.00 %) | 90 |
| Copper by the Sulfide Precipitation-Electrodeposition GravimetricMethod (0.01 to 10.00 %) | 71 |
| Iron by the Silver ReductionTitrimetric Method (1.0 to 50.0 %) | 192 |
| Manganese by the Periodate Photometric Method (0.05 to 2.00 %) | |
| Molybdenum by the Ion Exchange-8-Hydroxyquinoline Gravi-metric Method (1.5 to 30 %) | 184 |
| Molybdenum by the Photometric Method (0.01 to 1.50 %) | 153 |
| Nickel by the Dimethylglyoxime Gravimetric Method (0.1 to84.0 %) | 135 |
| Phosphorus by the Molybdenum Blue Photometric Method (0.002to 0.08 %) | 18 |
| Silicon by the Gravimetric Method (0.05 to 5.00 %) | 46 |
| Sulfur by the Gravimetric Method | 1 c |
| Sulfur by the Combustion-Iodate Titration Method (0.005 to0.1 %) | 37 |
| Sulfur by the Chromatographic Gravimetric Method | 1b |
| Tin by the Solvent Extraction-Atomic Absorption Method (0.002to 0.10 %) | 143 |
1.3 Methods for the determination of several elements not included in this standard can be found in Test Methods E30 and Test Methods E1019.
1.4 Some of the concentration ranges given in 1.1 are too broad to be covered by a single method and therefore this standard contains multiple methods for some elements. The user must select the proper method by matching the information given in the Scope and Interference sections of each method with the composition of the alloy to be analyzed.
1.5 The values stated in SI units are to be regarded as standard. In some cases, exceptions allowed in Practice E380 are also used.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 5 and in special "Warning" paragraphs throughout these test methods.
Keywords
aluminum; chromium; cobalt; cobalt alloys; combustion analysis; copper; high temperature alloys; induction furnace; infrared absorption; iron; manganese; magnetic alloys; molybdenum; nickel; nickel alloys; phosphorus; silicon; sulfur; tin; total carbon; ICS Number Code 77.140.40 (Steels with special magnetic properties)
To find similar documents by ASTM Volume:
03.05 (Analytical Chemistry for Metals, Ores, and Related Materials: E 32 - latest)
To find similar documents by classification:
77.140.40 (Steels with special magnetic properties)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A240Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASTM-E1316
Standard Terminology for Nondestructive Examinations
ASTM-E18
Standard Test Methods for Rockwell Hardness of Metallic Materials
Document Number
ASTM-E0354-21E01
Revision Level
2021(E1) EDITION
Status
Current
Modification Type
Editorially changed
Publication Date
Feb. 23, 2022
Document Type
Test Method
Page Count
36 pages
Committee Number
E01.01