ASTM-E1806 › Standard Practice for Sampling Steel and Iron for Determination of Chemical Composition
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 This practice covers the sampling of all grades of steel, both cast and wrought, and all types (grades) of cast irons and blast furnace iron for chemical and spectrochemical determination of composition. This practice is similar to ISO 14284.
1.2 This practice is divided into the following sections.
| Sections |
Requirements for Sampling and Sample Preparation | 6 |
General | 6.1 |
Sample | 6.2 |
Selection of a Sample | 6.3 |
Preparation of a Sample | 6.4 |
|
|
Liquid Iron for Steelmaking and Pig Iron Production | 7 |
General | 7.1 |
Spoon Sampling | 7.2 |
Probe Sampling | 7.3 |
Preparation of a Sample for Analysis | 7.4 |
|
|
Liquid Iron for Cast Iron Production | 8 |
General | 8.1 |
Spoon Sampling | 8.2 |
Probe Sampling | 8.3 |
Preparation of a Sample for Analysis | 8.4 |
Sampling and Sample Preparation for the Determination of | 8.5 |
Oxygen and Hydrogen |
|
|
|
Liquid Steel for Steel Production | 9 |
General | 9.1 |
Probe Sampling | 9.2 |
Spoon Sampling | 9.3 |
Preparation of a Sample for Analysis | 9.4 |
Sampling and Sample Preparation for the Determination | 9.5 |
of Oxygen |
|
Sampling and Sample Preparation for the Determination | 9.6 |
of Hydrogen |
|
|
|
Pig Irons | 10 |
General | 10.1 |
Increment Sampling | 10.2 |
Preparation of a Sample for Analysis | 10.3 |
|
|
Cast Iron Products | 11 |
General | 11.1 |
Sampling and Sample Preparation | 11.2 |
|
|
| Sections |
Steel Products | 12 |
General | 12.1 |
Selection of a Laboratory Sample or a Sample for | 12.2 |
Analysis from a Cast Product |
|
Selection of a Laboratory Sample or a Sample for | 12.3 |
Analysis from a Wrought Product |
|
Preparation of a Sample for Analysis | 12.4 |
Sampling of Leaded Steel | 12.5 |
Sampling and Sample Preparation for the Determination | 12.6 |
of Oxygen |
|
|
|
Sampling and Sample Preparation for the Determination | 12.7 |
of Hydrogen |
|
|
|
Keywords | 13 |
|
|
| Annexes |
Sampling Probes for Use with Liquid Iron and Steel | Annex A1 |
Sampling Probes for Use with Liquid Steel for the | Annex A2 |
Determination of Hydrogen |
|
1.3 The values stated in SI units are regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific statements, see 6.4.3.5, 9.4.4.3, 12.5.1, and Section 5.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Significance and Use
4.1 This practice covers all aspects of sampling and preparing steel and iron for chemical analysis as defined in Test Methods, Practices, and Definitions A751 and Specification A48/A48M. Such subjects as sampling location and the sampling of lots are defined.
4.2 This practice includes most requirements for sampling steel and iron for analysis. Standard test methods that reference this practice need contain only special modifications and exceptions.
4.3 All who use these procedures should be trained samplers capable of performing common sampling operations skillfully and safely. Only proper sampling equipment should be used.
Keywords
castings; iron sample; sample lot; steel sample ;
To find similar documents by ASTM Volume:
03.05 (Analytical Chemistry for Metals, Ores, and Related Materials: E 32 - latest)
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-E1316Standard Terminology for Nondestructive Examinations
ASTM-E18
Standard Test Methods for Rockwell Hardness of Metallic Materials
QPL-AMS-2644
Inspection Material, Penetrant
Document Number
ASTM-E1806-23
Revision Level
2023 EDITION
Status
Current
Modification Type
Revision
Publication Date
July 6, 2023
Document Type
Practice
Page Count
22 pages
Committee Number
E01.01