Document Center is acquired by Nimonik

Scope

1.1 Intent

1.1.1 This intent of this standard is to provide guidance for the design, fabrication, quality assurance, inspection, testing, packaging, shipping, installation and maintenance of radiation shielding window components. These window components include wall liner embedments, dry lead glass radiation shielding window assemblies, oil-filled lead glass radiation shielding window assemblies, shielding wall plugs, barrier shields, view ports, and the installation/extraction table/device required for the installation and removal of the window components.

1.2 Applicability

1.2.1 This standard is intended for those persons who are tasked with the planning, design, procurement, fabrication, installation, and operation of the radiation shielding window components that may be used in the operation of hot cells, high level caves, mini-cells, canyon facilities, and very high level radiation areas.

1.2.2 This standard applies to radiation shielding window assemblies used in normal concrete walls, high-density concrete walls, steel walls and lead walls.

1.2.3 The system of units employed in this standard is the metric unit, also known as SI Units, which are commonly used for International Systems, and defined, by ASTM/IEEE SI-10 Standard for Use of International System of Units. Common nomenclature for specifying some terms; specifically shielding, uses a combination of metric units and inch-pound units.

1.2.4 This standard identifies the special information required by the Manufacturer for the design of window components. A1.1 shows a sample list of the radiation source spectra and geometry information, typically required for shielding analysis. A2.1 shows a detailed sample list of specific data typically required to determine the physical size, glass types, and viewing characteristics of the shielding window, or view port. A3 shows general window configuration sketches. Blank copies of A1.2 and A2.2 are found in the respective Annexes for the Owner-Operator's use.

1.2.5 This standard is intended to be generic and to apply to a wide range of configurations and types of lead glass radiation shielding window components used in hot cells. It does not address glovebox, water, x-ray glass or zinc bromide windows.

1.3 Caveats

1.3.1 Consideration shall be given when preparing the shielding window designs for the safety related issues discussed in the Hazards Sources and Failure Modes, Section ; such as dielectric discharge, over-pressurization, radiation exposure, contamination, and overturning of the extraction table/device.

1.3.2 In many cases, the use of the word "shall" has been purposely used in lieu of "should" to stress the importance of the statements that have been made in this standard.

1.3.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Significance and Use

Radiation Shielding Window Components:

4.1.1 Radiation shielding window components operability and long-term integrity are concerns that originate during the design, and fabrication sequences. Such concerns can only be addressed, or are most efficiently addressed during one or the other of these stages. The operability and integrity can be compromised during handling and installation sequences. For this reason, the subject equipment should be handled and installed under closely controlled and supervised conditions.

4.1.2 This standard is intended as a supplement to other standards, and to federal and state regulations, codes, and criteria applicable to the design of radiation shielding window components.

Keywords

barrier shield; dielectric discharge; dry lead glass window; hot cell; installation/extraction table/device; installation and maintenance; oil-filled lead glass window; shielding glass; shielding oil; shielding plug; shielding window; view port; wall liner embedment; ICS Number Code 13.280 (Radiation protection)

To find similar documents by ASTM Volume:

12.01 (Nuclear Energy (I))

To find similar documents by classification:

13.280 (Radiation protection Including protection against radio-frequency radiation Radiation measurements, see 17.240)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.