ASTM-B94 › Standard Specification for Magnesium-Alloy Die Castings

ASTM-B94 - 2018 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers magnesium-alloy die castings. The magnesium alloys used for the manufacture of die castings shall conform to the chemical composition requirements of this specification. The producer or supplier is responsible for the performance of all inspection and test requirements when specified in the contract or purchase order. Samples for chemical analysis shall be taken from the material by drilling, sawing, milling, turning, or clipping a representative piece or pieces to obtain a weight of prepared sample the soundness of die castings which shall conform to standards or requirements agreed upon between the producer or supplier and the purchaser. Die castings shall have uniform quality that is free from injurious discontinuities that will adversely affect their serviceability. All castings shall be properly marked for identification with the part number, name or brand of the producer, as agreed upon the contract.

ORDER

Price:

$69.00        


Want this as a site license?

Changes from the previous issue

A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.

Scope

1.1 This specification covers magnesium-alloy die castings. Current alloy compositions are specified under the designations shown in Table 1.2

(A) Analysis shall regularly be made only for the elements specifically mentioned in this table. If, however, the presence of other elements is suspected or indicated in the course of routine analysis, further analysis shall be made to determine that these other elements are not in excess of 0.3 %.
(B) The following applies to all specified limits in this table: For purposes of acceptance and rejection an observed value or a calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding procedure prescribed in Section 3 of Practice E29.
(C) Where single units are shown, these indicate the maximum amounts permitted.
(D) ASTM alloy designations were established in accordance with Practice B951, UNS designations were established in accordance with Practice E527.
(E) In alloys AS41B, AM50A, AJ52A, AM60B, AJ62A, and AZ91D, if either the minimum manganese limit or the maximum iron limit is not met, then the iron/manganese ratio shall not exceed 0.010, 0.015, 0.015, 0.021, 0.021, and 0.032, respectively.
(F) Alloys AJ52A, AJ62A, and AS21B are patented compositions for elevated temperature applications. Interested parties are invited to submit information regarding the identification of alternatives to these compositions to ASTM International. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

1.2 The values stated in inch-pound units are standard. The SI values in parentheses are provided for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

casting characteristics; composition; high pressure die cast alloy; magnesium; mechanical properties; performance characteristics;; ICS Number Code 77.120.20 (Magnesium and magnesium alloys)

To find similar documents by ASTM Volume:

02.02 (Aluminum and Magnesium Alloys)

To find similar documents by classification:

77.120.20 (Magnesium and magnesium alloys)

77.150.20 (Magnesium products)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

IPC-A-610
Acceptability of Electronic Assemblies (Hardcopy format)

IPC-A-600
Acceptability of Printed Boards

IPC-2221
Generic Standard on Printed Board Design

Document Number

ASTM-B94-18

Revision Level

2018 EDITION

Status

Current

Modification Type

Revision

Publication Date

May 1, 2018

Document Type

Specification

Page Count

6 pages

Committee Number

B07.04