ASTM-B313 › Standard Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Withdrawn 2018)

ASTM-B313 - 2009 EDITION - CANCELLED -- See the following: ASTM-B313M
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers aluminum and aluminum-alloy tubes made from formed sheet and seam welded by continuous methods. Chemical conformance shall be determined by analyzing samples taken at a time the ingots are poured, or samples taken from the finished or semi-finished product, following conditions set in the specification. The temper of the tubes shall be that of the sheet from which the tubes are formed, and the sheet shall conform to the specified tensile property requirements. The tube shall be subjected to tension, capability, and pressure tests.

ORDER

Want this as a site license?

Scope

1.1 This specification covers aluminum and aluminum-alloy tubes made from formed sheet and seam welded by continuous methods.

1.2 Alloy (Note 1) and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.

Note 1—Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.

Note 2—For the requirements for sheet see Specification B209.

1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see A1.2.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4.1 SI Units—The SI units are shown either in brackets or in separate tables.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

aluminum alloy; welded tubes; Aluminum alloys (tube)--specifications; Aluminum tube--specifications; UNS A91100 (Wr. alum. alloy)--tube; UNS A93003 (Wr. alum. alloy)--tube; UNS A93004 (Wr. alum. alloy)--tube; UNS A95050 (Wr. alum. alloy)--tube; UNS A95052 (Wr. alum. alloy)--tube; UNS A95086 (Wr. alum. alloy)--tube; UNS A95154 (Wr. alum. alloy)--tube; UNS A96061 (Wr. alum. alloy)--tube; UNS A97072 (Wr. alum. alloy)--tube; ICS Number Code 77.150.10 (Aluminium products)

To find similar documents by ASTM Volume:

02.02 (Aluminum and Magnesium Alloys)

To find similar documents by classification:

77.150.10 (Aluminium products)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

UL-1741
Standard for Inverters, Converters, Controllers and Interconnection System Equipment for Use With Distributed Energy Resources

UL-BULL-2264
UL Bulletin - Subject 2264: Results From the Task Group Formed at the Stp Meeting Held

IEEE-929
Utility Interface of Photovoltaic (Pv) Systems, IEEE Recommended Practice For

Document Number

ASTM-B313/B313M-09

Revision Level

2009 EDITION

Status

Cancelled

Modification Type

Withdrawn

Publication Date

Dec. 1, 2009

Document Type

Specification

Page Count

10 pages

Committee Number

B07.03