ASTM-B150 › Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
The following bibliographic material is provided to assist you with your purchasing decision:
This specification establishes the requirements for rods, bars, and shapes of aluminum bronze with Copper Alloy UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210. Products shall be produced in tempers HR50, M10, M20, M30, O20, O25, O30, O32, TQ30, TQ50 and TQ55. Products shall be tested and shall conform to dimensional (mass, diameter, length, thickness, straightness, and edge contour), mechanical (tensile and yield strength, Rockwell hardness, and elongation), and chemical composition requirements. Products should also meet requirements under mercurous nitrate test, ammonia test, and piston finish.
Changes from the previous issue
A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.
Scope
1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210.
Note 1: Product intended for hot forging is described in Specification B124/B124M.
Note 2: Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
aluminum bronze bar; aluminum bronze rod; aluminum bronze shapes; UNS Alloy No. C61300; UNS Alloy No. C61400; UNS Alloy No. C61900; UNS Alloy No. C62300; UNS Alloy No. C62400; UNS Alloy No. C63000; UNS Alloy No. C63020; UNS Alloy No. C63200; UNS Alloy No. C64200; UNS Alloy No. C64210;; ICS Number Code 77.150.10 (Aluminium products)
To find similar documents by ASTM Volume:
02.01 (Copper and Copper Alloys)
To find similar documents by classification:
77.150.10 (Aluminium products)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A240Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASTM-E18
Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM-A276
Standard Specification for Stainless Steel Bars and Shapes
Document Number
ASTM-B150/B150M-19
Revision Level
2019 EDITION
Status
Current
Modification Type
Revision
Publication Date
April 1, 2019
Document Type
Specification
Page Count
7 pages
Committee Number
B05.02