ASTM-A530 Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe

ASTM-A530 - 2018 EDITION - CURRENT -- See the following: ASTM-A530/A530M
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers a general requirements for specialized carbon and alloy steel pipe. Tensile tests, tension tests, flattening tests, hydrostatic tests and ultrasonic tests shall be made to conform to the requirements specified. If the mechanical results do not conform to the requirements specified, retests shall be made. Defects in seamless pipe shall be repaired by welding.

ORDER

Price:

$69.00        


Want this as a site license?

Scope

1.1 This specification2 covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail.

1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests.

1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters.

1.4 Section 14 is for information only.

1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied.

Title of Specification

ASTM DesignationA

Seamless Carbon Steel Pipe for High-Temperature Service

A106/A106M

Metal-Arc-Welded Steel Pipe for Use With High-Pressure
    Transmission Systems

A381

Seamless Carbon Steel Pipe for Atmospheric and Lower
    Temperatures

A524

Centrifugally Cast Carbon Steel Pipe for High-Temperature
    Service

A660/A660M

Electric-Fusion-Welded Steel Pipe for Atmospheric and
    Lower Temperatures

A671/A671M

Electric-Fusion-Welded Steel Pipe for High-Pressure Service
    at Moderate Temperatures

A672/A672M

Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for
    High-Pressure Service at High Temperatures

A691/A691M

1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.

Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

alloy steel pipe; carbon steel pipe; general delivery requirements; steel pipe;

To find similar documents by ASTM Volume:

01.01 (Steel--Piping, Tubing, Fittings)

To find similar documents by classification:

23.040.10 (Iron and steel pipes Steel pipes and tubes for specific use, see 77.140.75)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASME-B1.1
Unified Inch Screw Threads, (UN and UNR Thread Form)

MS-16199
Screws, Wood, Slotted, Flat Countersunk (82 Deg.) Head, Copper-Silicon Alloy, Nonmagnetic

ASTM-B633
Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel

Document Number

ASTM-A530/A530M-18

Revision Level

2018 EDITION

Status

Current

Modification Type

Revision

Publication Date

Sept. 1, 2018

Document Type

Specification

Page Count

9 pages

Committee Number

A01.09