Document Center List of Standards on Central Heating Systems Including Burners And Boilers For Central Heating Systems Heating Appliances, See 97.100
ICS Code 91.140.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-D8039 - Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems
- ASTM-E2618 - Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel-Fired Hydronic Heating Appliances
- ASTM-F2929 - Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig
- ASTM-F856 - Standard Practice for Mechanical Symbols, Shipboard—Heating, Ventilation, and Air Conditioning (HVAC)
BSI:
- BS-2767 - Specification for manually operated copper alloy valves for radiators
- BS-2879 - Specification for draining taps (screw-down pattern)
- BS-3377 - Specification for boilers for use with domestic solid mineral fuel appliances
- BS-3528 - Specification for convection type space heaters operating with steam or hot water
- BS-4433-1 - Domestic solid mineral fuel fired boilers with rated output up to 45 kW. Domestic solid mineral fuel fired boilers with rated output up to 45 kw. Specification for boilers with undergrate ash removal
- BS-4433-2 - Domestic solid mineral fuel fired boilers with rated output up to 45 kW. Specification for gravity feed boilers designed to burn small anthracite
- BS-5258-1 - Safety of domestic gas appliances. Specification for central heating boilers and circulators
- BS-5258-15 - Safety of domestic gas appliances. Specification for combination boilers
- BS-5258-1 SUP1 - Safety of domestic gas appliances
- BS-5376-2 - Code of practice for selection and installation of gas space heating (1st and 2nd family gases)
- BS-5449 - Specification for forced circulation hot water central heating systems for domestic premises
- BS-5449-1 - Code of practice for central heating for domestic premises.
- BS-5871-1 - Specification for the installation and maintenance of gas fires, convector heaters, fire/back boilers and decorative fuel effect gas appliances
- BS-5955-8 - Plastics pipework (thermoplastics materials)
- BS-6332-1 - Thermal performance of domestic gas appliances. Specification for thermal performance of central heating boilers and circulators
- BS-6798 - Specification for selection, installation, inspection, commissioning, servicing and maintenance of gas-fired boilers of rated input not exceeding 70 kW net
- BS-7074-1 - Application, selection and installation of expansion vessels and ancillary equipment for sealed water systems
- BS-7074-2 - Application, selection and installation of expansion vessels and ancillary equipment for sealed water systems
- BS-7074-3 - Application, selection and installation of expansion vessels and ancillary equipment for sealed water systems
- BS-7593-TC - Tracked Changes. Code of practice for the preparation, commissioning and maintenance of domestic central heating and cooling water systems
- BS-779 - Specification for cast iron boilers for central heating and indirect hot water supply (rated output 44 kW and above)
- BS-7977-2 - Specification for safety and rational use of energy of domestic gas appliances
- BS-853-1 - Specification for vessels for use in heating systems
- BS-855 - Specification for welded steel boilers for central heating and indirect hot water supply (rated output 44 kW to 3 MW)
- BS-8660-1 - Gas-fired micro-cogeneration appliances of rated thermal input not exceeding 70 kW net
- BS-EN-1148 - Heat exchangers. Water-to-water heat exchangers for district heating. Test procedures for establishing the performance data
- BS-EN-12098-1 - Energy performance of buildings. Controls for heating systems
- BS-EN-12098-1-TC - Tracked Changes. Energy Performance of Buildings. Controls for heating systems
- BS-EN-12098-2 - Controls for heating systemsOptimum start-stop control equipment for hot water heating systems
- BS-EN-12098-5 - Energy Performance of Buildings. Controls for heating systems
- BS-EN-12170 - Heating systems in buildings. Procedure for the preparation of documents for operation, maintenance and use. Heating systems requiring a trained operator
- BS-EN-12171 - Heating systems in buildings. Procedure for the preparation of documents for operation, maintenance and use. Heating systems not requiring a trained operator
- BS-EN-1264-1 - Water based surface embedded heating and cooling systems
- BS-EN-1264-1-TC - Tracked Changes. Water based surface embedded heating and cooling systems
- BS-EN-1264-2 - Water based surface embedded heating and cooling systems
- BS-EN-1264-3 - Water based surface embedded heating and cooling systems
- BS-EN-1264-3-TC - Tracked Changes. Water based surface embedded heating and cooling systems
- BS-EN-1264-4 - Water based surface embedded heating and cooling systems
- BS-EN-1264-4-TC - Tracked Changes. Water based surface embedded heating and cooling systems
- BS-EN-1264-5 - Water based surface embedded heating and cooling systems
- BS-EN-1264-5-TC - Tracked Changes. Water based surface embedded heating and cooling systems
- BS-EN-12809 - Residential independent boilers fired by solid fuel. Nominal heat output up to 50 kW. Requirements and test methods
- BS-EN-12828 - Heating systems in buildings. Design for water-based heating systems
- BS-EN-12831 - Heating systems in buildings. Method for calculation of the design heat load
- BS-EN-12831-1 - Energy performance of buildings. Method for calculation of the design heat load
- BS-EN-12831-1-TC - Tracked Changes. Energy performance of buildings. Method for calculation of the design heat load
- BS-EN-12831-3 - Energy performance of buildings. Method for calculation of the design heat load
- BS-EN-12831-3-TC - Tracked Changes. Energy performance of buildings. Method for calculation of the design heat load
- BS-EN-12977-2-TC - Tracked Changes. Thermal solar systems and components. Custom built systems
- BS-EN-12977-3-TC - Tracked Changes. Thermal solar systems and components. Custom built systems
- BS-EN-13831 - Closed expansion vessels with built-in diaphragm for installation in water
- BS-EN-13941 - Design and installation of preinsulated bonded pipe systems for district heating
- BS-EN-13941-1 - District heating pipes. Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks
- BS-EN-13941-2 - District heating pipes. Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks
- BS-EN-14037-1 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14037-1-TC - Tracked Changes. Free hanging heating and cooling surfaces for water with a temperature below 120°C
- BS-EN-14037-2 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14037-2-TC - Tracked Changes. Free hanging heating and cooling surfaces for water with a temperature below 120°C
- BS-EN-14037-3 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14037-3-TC - Tracked Changes. Free hanging heating and cooling surfaces for water with a temperature below 120°C
- BS-EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14037-5 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14336 - Heating systems in buildings. Installation and commissioning of water based heating systems
- BS-EN-14337 - Heating systems in buildings. Design and installation of direct electrical room heating systems
- BS-EN-14394 - Heating boilers. Heating boilers with forced draught Burners. Nominal heat output not exceeding 10 MW and maximum operating temperature of 110C
- BS-EN-15036-1 - Heating boilers. Test regulations for airborne noise emissions from heat generators
- BS-EN-15036-2 - Heating boilers. Test regulations for airborne noise emissions from heat generators
- BS-EN-15232 - Energy performance of buildings. Impact of Building Automation, Controls and Building Management
- BS-EN-15316-1 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-1-TC - Tracked Changes. Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-2 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-2-1 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Space heating emission systems
- BS-EN-15316-2-3 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Space heating distribution systems
- BS-EN-15316-3 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-3-1 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-3-2 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Domestic hot water systems, distribution
- BS-EN-15316-3-3 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Domestic hot water systems, generation
- BS-EN-15316-4-1 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-10 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-2 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-3 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-4 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-4-TC - Tracked Changes. Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-5 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-5-TC - Tracked Changes. Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-6 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Heat generation systems, photovoltaic systems
- BS-EN-15316-4-7 - Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Space heating generation systems, biomass combustion systems
- BS-EN-15316-4-8 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-8-TC - Tracked Changes. Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-5 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15377-1 - Heating systems in buildings. Design of embedded water based surface heating and cooling systems. Determination of the design heating and cooling capacity
- BS-EN-15377-2 - Heating Systems in Buildings, Design of Embedded Water Based Surface Heating & Cooling
- BS-EN-15377-3 - Heating systems in buildings. Design of embedded water based surface heating and cooling systems
- BS-EN-15378 - Heating systems in buildings. Inspection of boilers and heating systems
- BS-EN-15378-1 - Energy performance of buildings. Heating systems and DHW in buildings
- BS-EN-15378-1-TC - Tracked Changes. Energy performance of buildings. Heating systems and DHW in buildings
- BS-EN-15378-3 - Energy performance of buildings. Heating and DHW systems in buildings
- BS-EN-15417 - Gas-fired central heating boilers. Specific requirements for condensing boilers with a nominal heat input greater than 70 kW but not exceeding 1000 kW
- BS-EN-15420 - Gas-fired central heating boilers. Type C boilers of nominal heat input exceeding 70 kW, but not exceeding 1000 kW
- BS-EN-15450 - Heating systems in buildings. Design of heat pump heating systems
- BS-EN-15456 - Heating boilers. Electrical power consumption for heat generators. System boundaries. Measurements
- BS-EN-15459 - Energy performance of buildings. Economic evaluation procedure for energy systems in buildings
- BS-EN-15459-1 - Energy performance of buildings. Economic evaluation procedure for energy systems in buildings
- BS-EN-15459-1-TC - Tracked Changes. Energy performance of buildings. Economic evaluation procedure for energy systems in buildings
- BS-EN-15502-1 - Gas-fired heating boilers
- BS-EN-15502-1-TC - Tracked Changes. Gas-fired heating boilers
- BS-EN-15502-2-1 - Gas-fired central heating boilers
- BS-EN-15502-2-2 - Gas-fired central heating boilers
- BS-EN-16313 - Connections for heating and cooling appliances. Detachable connection with outside threaded pipe G A and inside cone
- BS-EN-16430-1 - Fan assisted radiators, convectors and trench convectors
- BS-EN-16430-2 - Fan assisted radiators, convectors and trench convectors
- BS-EN-16430-3 - Fan assisted radiators, convectors and trench convectors
- BS-EN-16510-1 - Residential solid fuel burning appliances
- BS-EN-17522 - Design and construction of backfilled and grouted borehole heat exchangers
- BS-EN-17690-1 - Components for BAC control loop. Sensors
- BS-EN-17956 - Energy efficiency classes for technical insulation systems. Calculation method and applications
- BS-EN-215 - Thermostatic radiator valves. Requirements and test methods
- BS-EN-26 - Gas-fired instantaneous water heaters for the production of domestic hot water
- BS-EN-297 - Gas-fired central heating boilers. Type B
- BS-EN-303-1 - Heating boilers
- BS-EN-303-1-TC - Tracked Changes. Heating boilers
- BS-EN-303-2 - Heating boilers
- BS-EN-303-3 - Heating boilers
- BS-EN-303-5 - Heating boilers
- BS-EN-303-5-TC - Tracked Changes. Heating boilers
- BS-EN-303-6 - Heating boilers
- BS-EN-303-7 - Heating boilers
- BS-EN-304 - Heating boilers. Test code for heating boilers for atomizing oil burners
- BS-EN-304-TC - Tracked Changes. Heating boilers. Test code for heating boilers for atomizing oil burners
- BS-EN-442-1 - Radiators and convectors
- BS-EN-442-2 - Radiators and convectors
- BS-EN-442-3 - Specification for radiators and convectors. Evaluation of conformity
- BS-EN-483 - Gas-fired central heating boilers. Type C boilers of nominal heat input not exceeding 70 kW
- BS-EN-50379-1 - Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances
- BS-EN-50379-2 - Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances
- BS-EN-50379-3 - Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances
- BS-EN-60335-2-51 - Household and similar electrical appliances. Safety
- BS-EN-625 - Gas-fired central heating boilers. Specific requirements for the domestic hot water operation of combination boilers of nominal heat input not exceeding 70 kW
- BS-EN-656 - Gas-fired central heating boilers. Type B boilers of nominal heat input exceeding 70 kW, but not exceeding 300 kW
- BS-EN-677 - Gas-fired central heating boilers. Specific requirements for condensing boilers with a nominal heat input not exceeding 70 kW
- BS-EN-832 - Thermal Performance of Buildings. Calculation of Energy Usefor Heating. Residential B
- BS-EN-834 - Heat cost allocators for the determination of the consumption of room heating radiators. Appliances with electrical energy supply
- BS-EN-IEC-60335-2-51 - Household and similar electrical appliances. Safety
- BS-EN-ISO-11855-1 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-1-TC - Tracked Changes. Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-2 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-3 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-4 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-4-TC - Tracked Changes. Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-5 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-5-TC - Tracked Changes. Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-13790 - Energy performance of buildings. Calculation of energy use for space heating and cooling
- BS-ISO-13675 - Heating systems in buildings. Method and design for calculation of the system energy performance. Combustion systems (boilers)
- BS-ISO-52031 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies. Space emission systems (heating and cooling)
- CP-1018 - Electric floorwarming systems for use with off-peak and similar supplies of electricity
- CP-341.300-307 - Central heating by low pressure hot water
- PAS-2030 - Installation of energy efficiency measures in existing dwellings. Specification
- PAS-2030 ONLINE 10 L - Improving the energy efficiency of existing buildings. Specification for installation process, process management and service provision
- PAS-2030 ONLINE 3 LI - Improving the energy efficiency of existing buildings. Specification for installation process, process management and service provision
- PAS-2030 ONLINE 5 LI - Improving the energy efficiency of existing buildings. Specification for installation process, process management and service provision
- PAS-2030 ONLINE SING - Improving the energy efficiency of existing buildings. Specification for installation process, process management and service provision
- PAS-2031 - Certification of energy efficiency measure installation in existing buildings and insulation in residential park homes
- PAS-2035 - Retrofitting dwellings for improved energy efficiency. Specification and guidance
- PAS-2035/2030 - Retrofitting dwellings for improved energy efficiency. Specification and guidance
- PAS-2035/2030-ONLINE - Retrofitting dwellings for improved energy efficiency. Specification and guidance.
- PAS-2038 - Retrofitting non-domestic buildings for improved energy efficiency. Specification
- PD-CEN-12098-6 - Energy performance of buildings. Controls for heating systems
- PD-CEN-12098-7 - Energy performance of buildings. Controls for heating systems
- PD-CEN-12098-7-TC - Tracked Changes. Energy performance of buildings. Controls for heating systems
- PD-CEN-12098-8 - Controls for heating systems
- PD-CEN-12831-2 - Energy performance of buildings. Method for calculation of the design heat load
- PD-CEN-12831-4 - Energy performance of buildings. Method for calculation of the design heat load
- PD-CEN-15316-6-1 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-10 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-2 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-3 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-4 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-5 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-6 - Energy performance of buildings. Method for calculation of system energy performance and system efficiencies
- PD-CEN-15316-6-7 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-8 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-9 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15378-2 - Energy performance of buildings. Heating systems and DHW in buildings
- PD-CEN-15378-4 - Energy performance of buildings. Heating systems and DHW in buildings
- PD-CEN-15459-2 - Energy performance of buildings. Economic evaluation procedure for energy systems in buildings
- PD-CEN-15502-3-1 - Gas-fired central heating boilers
- PD-CEN-16911 - Heat meters. Recommendations for circulation water in industrial and district heating systems and their operation
- PD-CLC-50612 - Portable electrical apparatus for the measurement of combustion flue gas parameters. Guide to their use in the process of commissioning, servicing and maintaining gas fired appliances
- PD-CLC-50612-TC - Tracked Changes. Portable electrical apparatus for the measurement of combustion flue gas parameters. Guide to their use in the process of commissioning, servicing and maintaining gas fired appliances
IEC:
- IEC-60335-2-51 - Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
- IEC-60335-2-51-1 - Amendment 1: Household & Similar Electrical Appliances - Safety - Part 2-51: Particula
- IEC-60335-2-51-AM2 - Amendment 2 - Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
- IEC-60335-2-51-RL - Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
ISO:
Other SDOs:
- BS-EN-15502-2-2-TC - Tracked Changes. Gas-fired central heating boilers
- DIN-EN-1148/A1 - Amendment 1 for Din-En-1148, Heat Exchangers - Water To Water Heat Exchangers for Dist
- DIN-EN-12098-5 - Part 5: Start-Stop Shcedulers for Heating Systems, Controls for Heating Systems
- DIN-EN-1264-2 - Water based surface embedded heating and cooling systems - Part 2: Floor heating: Prove methods for the determination of the thermal output using calculation and test methods; German version EN 1264-2:2008+A1:2012
- DIN-EN-1264-4 - Water based surface embedded heating and cooling systems - Part 4: Installation; German version EN 1264-4:2009
- DIN-EN-12809 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods; German version EN 12809:2001 + A1:2004
- DIN-EN-12828 - Heating systems in buildings - Design for water-based heating systems; German version EN 12828:2012+A1:2014
- DIN-EN-12831 - Heating Systems in Buildings, Method for Calculation of the Design Heat Load
- DIN-EN-13836 - Gas-Fired Central Heating Boilers - Type B Boilers of Nominal Heat Input Exceeding 300
- DIN-EN-13941 - Design & Installation of Preinsulated Bonded Pipe Systems for District Heating
- DIN-EN-14037-2 - Free hanging heating and cooling surfaces for water with a temperature below 120 °C - Part 2: Pre-fabricated ceiling mounted radiant panels for space heating - Test method for thermal output; German version EN 14037-2:2016
- DIN-EN-14037-3 - Free hanging heating and cooling surfaces for water with a temperature below 120 °C - Part 3: Prefabricated ceiling mounted radiant panels for space heating- Rating method and evaluation of radiant thermal output; German version EN 14037-3:2016
- DIN-EN-14336 - Heating Systems in Buildings, Installation & Commissioning of Water-Based Heating Syst
- DIN-EN-14337 - Heating Systems in Buildings - Design & Installation of Direct Electrical Room Heating
- DIN-EN-14394 - Heating Boilers - Heating Boilers With Forced Draught Burners - Nominal Heat Output No
- DIN-EN-15036-1 - Part 1: Airborne Noise Emissions From Heat Generators, Heating Boilers - Test Regulati
- DIN-EN-15036-2 - Part 2: Flue Gas Noise Emissions at the Outlet of the Heat Generator, Heating Boilers
- DIN-EN-15417 - Gas-fired central heating boilers - Specific requirements for condensing boilers with a nominal heat input greater than 70 kW but not exceeding 1000 kW; German version EN 15417:2006
- DIN-EN-215 - Thermostatic Radiator Valves - Requirements and Test Methods
- DIN-EN-303-7 - Part 7: Gas-Fired Central Heating Boilers Equipped With a Forced Draught Burner of Nom
- DIN-EN-442-2 - Radiators and convectors - Part 2: Test methods and rating; German version EN 442-2:2014
- DIN-EN-442-3 - Radiators and convectors - Part 3: Evaluation of conformity; German version EN 442-3:2003
- DIN-EN-483/A2 - Gas-Fired Central Heating Boilers - Type C Boilers of Nominal Heat Input Not Exceeding
- DIN-EN-656/A1 - Gas-Fired Central Heating Boilers - Type B Boilers of Nominal Heat Input Exceeding 70
- DIN-EN-832 - Thermal Performance of Buildings, Calculation of Energy Use for Heating - Residential
- DIN-EN-ISO-13790 - Thermal Performance of Buildings, Calculation of Energy Use for Space Heating
- DIN-EN-ISO-15927-4 - Part 4: Hourly Data for Assessing the Annual Energy Use for Heating & Cooling, Hygrot
- EN-1148/A1 - Heat Exchangers - Water To Water Heat Exchangers for District Heating - Test Procedure
- EN-12098-1 - Energy Performance of Buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8
- EN-12098-5 - Energy Performance of Buildings - Controls for heating systems - Part 5: Start-stop schedulers for heating systems - Modules M3-5,6,7,8
- EN-1264-1 - Water based surface embedded heating and cooling systems - Part 1: Definitions and symbols
- EN-1264-4 - Part 4: Installation, Water Based Surface Embedded Heating & Cooling Systems
- EN-1264-5 - Water Based Surface Embedded Heating & Cooling Systems, Heating & Cooling Surfaces Emb
- EN-12809 - Residential Independent Boilers Fired by Solid Fuel - Nominal Heat Output Up To 50 Kw,
- EN-12828 - Heating systems in buildings - Design for water-based heating systems
- EN-12831-1 - Energy performance of buildings - Method for calculation of the design heat load - Part 1: Space heating load, Module M3-3
- EN-12831-3 - Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3
- EN-13831 - Closed Expansion Vessels With Built in Diaphragm for Installation in Water
- EN-13941 - Design & Installation of Preinsulated Bonded Pipe Systems for District Heating
- EN-13941-1 - District heating pipes - Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks - Part 1: Design
- EN-13941-2 - District heating pipes - Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks - Part 2: Installation
- EN-14037-1 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 1: Pre-fabricated ceiling mounted radiant panels for space heating - Technical specifications and requirements
- EN-14037-2 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 2: Pre-fabricated ceiling mounted radiant panels for space heating - Test method for thermal output
- EN-14037-3 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 3: Prefabricated ceiling mounted radiant panels for space heating - Rating method and evaluation of radiant thermal output
- EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
- EN-14037-5 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output
- EN-14336 - Heating Systems in Buildings, Installation & Commissioning of Water-Based Heating Syst
- EN-14337 - Heating Systems in Buildings - Design & Installation of Direct Electrical Room Heating
- EN-14394 - Heating Boilers - Heating Boilers With Forced Draught Burners - Nominal Heat Output No
- EN-15036-1 - Part 1: Airborne Noise Emissions From Heat Generators, Heating Boilers - Test Regulati
- EN-15036-2 - Part 2: Flue Gas Noise Emissions at the Outlet of the Heat Generator, Heating Boilers
- EN-15316-1 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 1: General and Energy performance expression, Module M3-1, M3-4, M3-9, M8-1, M8-4
- EN-15316-2 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 2: Space emission systems (heating and cooling), Module M3-5, M4-5
- EN-15316-2-1 - Part 2-1: Space Heating Emission Systems, Heating Systems in Buildings - Method for Ca
- EN-15316-2-3 - Heating Systems in Buildings, Method for Calculation of System Energy Requirements & S
- EN-15316-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 3: Space distribution systems (DHW, heating and cooling), Module M3-6, M4-6, M8-6
- EN-15316-3-1 - Part 3-1: Domestic Hot Water Systems, Characterization of Needs (Tapping Requirements)
- EN-15316-3-2 - Part 3-2: Domestic Hot Water System, Distribution, Heating Systems in Buildings - Meth
- EN-15316-3-3 - Part 3-3: Domestic Hot Water Systems, Generation; Heating Systems in Buildings - Metho
- EN-15316-4-1 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-1: Space heating and DHW generation systems, combustion systems (boilers, biomass), Module M3-8-1, M8-8-1
- EN-15316-4-10 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-10: Wind power generation systems, Module M11-8-7
- EN-15316-4-2 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
- EN-15316-4-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-3: Heat generation systems, thermal solar and photovoltaic systems, Module M3-8-3, M8-8-3, M11-8-3
- EN-15316-4-4 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-4: Heat generation systems, building-integrated cogeneration systems, Module M8-3-4, M8-8-4, M8-11-4
- EN-15316-4-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-5: District heating and cooling, Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- EN-15316-4-6 - Part 4-6: Heat Generation Systems, Photovoltaic Systems, Heating Systems in Buildings
- EN-15316-4-7 - Part 4-7: Space Heating Generation Systems, Blomass Combustion Systems, Heating System
- EN-15316-4-8 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-8: Space heating generation systems, air heating and overhead radiant heating systems, including stoves (local), Module M3-8-8
- EN-15316-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 5: Space heating and DHW storage systems (not cooling), Module M3-7, M8-7
- EN-15377-1 - Part 1: Determination of the Design Heating & Cooling Capacity, Heating Systems in Bui
- EN-15377-2 - Part 2: Design, Dimensioning & Installation, Heating Systems in Buildings - Design Of
- EN-15377-3 - Heating Systems in Buildings, Design of Embedded Water Based Surface Heating & Cooling
- EN-15378 - Heating Systems in Buildings - Inspection of Boilers & Heating Systems
- EN-15378-1 - Energy performance of buildings - Heating systems and DHW in buildings - Part 1: Inspection of boilers, heating systems and DHW, Module M3-11, M8-11
- EN-15378-3 - Energy performance of buildings - Heating and DHW systems in buildings - Part 3: Measured energy performance, Module M3-10, M8-10
- EN-15417 - Gas-Fired Central Heating Boilers - Specific Requirements for Condensing Boilers With
- EN-15420 - Gas-fired central heating boilers - Type C boilers of nominal heat input exceeding 70 kW, but not exceeding 1 000 kW
- EN-15450 - Heating Systems in Buildings, Design of Heat Pump Heating Systems
- EN-15456 - Heating Boilers - Electrical Power Consumption for Heat Generators - System Boundaries
- EN-15459 - Energy Performance of Buildings - Economic Evaluation Procedure for Energy Systems In
- EN-15459-1 - Energy performance of buildings - Economic evaluation procedure for energy systems in buildings - Part 1: Calculation procedures, Module M1-14
- EN-15502-1 - Gas-fired heating boilers - Part 1: General requirements and tests
- EN-15502-2-1 - Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
- EN-15502-2-2 - Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
- EN-16313 - Connections for heating and cooling appliances - Detachable connection with outside threaded pipe G -+ A and inside cone
- EN-16430-1 - Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
- EN-16430-2 - Fan assisted radiators, convectors and trench convectors - Part 2: Test method and rating for thermal output
- EN-16430-3 - Fan assisted radiators, convectors and trench convectors - Part 3: Test method and rating for cooling capacity
- EN-16510-1 - Residential solid fuel burning appliances - Part 1: General requirements and test methods
- EN-215 - Thermostatic Radiator Valves - Requirements & Test Methods
- EN-26 - Gas-fired instantaneous water heaters for the production of domestic hot water
- EN-303-1 - Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking
- EN-303-2 - Heating boilers - Part 2: Heating boilers with forced draught burners - Special requirements for boilers with atomizing oil burners
- EN-303-3 - Gas-Fired Central Heating Boilers - Assembly Comprising a Boiler Body & a Forced Draug
- EN-303-5 - Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking
- EN-303-7 - Part 7: Gas-Fired Central Heating Boilers Equipped With a Forced Draught Burner of Nom
- EN-304 - Heating boilers - Test code for heating boilers for atomizing oil burners
- EN-442-1 - Radiators and convectors - Part 1: Technical specifications and requirements
- EN-442-2 - Radiators and convectors - Part 2: Test methods and rating
- EN-483 - Gas-Fired Central Heating Boilers, Type C Boilers of Nominal Heat Input Not Exceeding
- EN-60335-2-51 - Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
- EN-656 - Gas Fired Central Heating Boilers, Type B Boilers of Nominalheat Input Exceeding 70 Kw
- EN-656/A1 - Gas-Fired Central Heating Boilers - Type B Boilers of Nominal Heat Input Exceeding 70
- EN-832 - Thermal Performance of Buildings, Calculation of Energy Use for Heating - Residential
- EN-834 - Heat cost allocators for the determination of the consumption of room heating radiators - Appliances with electrical energy supply
- EN-ISO-11855-1 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 1: Definition, symbols, and comfort criteria
- EN-ISO-11855-2 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity
- EN-ISO-11855-3 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 3: Design and dimensioning
- EN-ISO-11855-4 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS)
- EN-ISO-11855-5 - Building environment design - Design , dimensioning, installation and control of embedded radiant heating and cooling systems - Part 5: Installation
- EN-ISO-13790 - Energy Performance of Buildings, Calculation of Energy Use for Space Heating & Cooling
- EN-ISO-15927-4 - Part 4: Hourly Data for Assessing the Annual Energy Use for Heating & Cooling, Hygrot
- EN-ISO-636 - Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification
- SIS-CEN/TR-12098-6 - Controls for heating systems - Part 6: Accompanying TR prEN 12098-1:2015 - Modules M3-5,6,7,8
- SIS-CEN/TR-12098-7 - Controls for heating systems - Part 7: Accompanying TR prEN 12098-3:2015 - Modules M3-5,6,7,8
- SIS-CEN/TR-12098-8 - Controls for heating systems - Part 8: Accompanying TR prEN 12098-5:2015 - Modules M3-5,6,7,8
- SIS-CEN/TR-12831-2 - Energy performance of buildings - Method for calculation of the design heat load - Part 2: Explanation and justification of EN 12831-1, Module M3-3
- SIS-CEN/TR-12831-4 - Energy performance of buildings - Method for calculation of the design heat load - Part 4: Explanation and justification of EN 12831-3, Module M8-2, M8-3
- SIS-CEN/TR-15316-6-1 - Energy performance of buildings- Method for calculation of system energy requirements and system efficiencies - Part 6-1: Explanation and justification of EN 15316-1, Module M3-1, M3-4, M3-9, M8-1, M8-4
- SIS-CEN/TR-15316-6-10 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-10: Explanation and justification of EN 15316-5, Module M3-7, M8-7
- SIS-CEN/TR-15316-6-2 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-2: Explanation and justification of EN 15316-2, Module M3-5, M4-5
- SIS-CEN/TR-15316-6-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-3: Explanation and justification of 15316-3, Module M3-6, M4-6, M8-6
- SIS-CEN/TR-15316-6-4 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-4: Explanation and justification of EN 15316-4-1, Module M3-8-1, M8-8-1
- SIS-CEN/TR-15316-6-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-5: Explanation and justification of EN 15316-4-2, Module M3-8
- SIS-CEN/TR-15316-6-6 - Energy performance of buildings - Method for calculation of system energy performance and system efficiencies - Part 6-6: Explanation and justification of EN 15316-4-3, Module M3-8-3, M8-8-3
- SIS-CEN/TR-15316-6-7 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-7: Explanation and justification of EN 15316-4-4, Module M8-3-4, M8-8-4, M8-11-4
- SIS-CEN/TR-15316-6-8 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-8: Explanation and justification of EN 15316-4-5 (District heating and cooling), Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- SIS-CEN/TR-15316-6-9 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-9: Explanation and justification of EN 15316-4-8, Module M3-8-8
- SIS-CEN/TR-15378-2 - Energy performance of buildings - Heating systems and DHW in buildings - Part 2: Explanation and justification of EN 15378-1, Module M3-11 and M8-11
- SIS-CEN/TR-15378-4 - Energy performance of buildings - Heating systems and DHW in buildings - Part 4: Explanation and justification of EN 15378-3, Module M3-10, M8-10
- SIS-CEN/TR-15459-2 - Energy performance of buildings - Economic evaluation procedure for energy systems in buildings - Part 2: Explanation and justification of EN 15459-1, Module M1-14
- SIS-CEN/TR-15760 - Heat meters - Checklist documenting the relationship between the Directive 2004/22/EC (MID) and EN 1434:2007
- SIS-CEN/TR-16911 - Heat meters - Recommendations for circulation water in industrial and district heating systems and their operation
- SIS-CWA-16975 - Eco-efficient Substations for District Heating
- SIS-TR-4 - Marking of gas appliances; contains extract from EN 437; CEN/CR 1472:1997, CEN/CR 1749:2001
- SS-EN-1148 - Heat exchangers - Water to water heat exchangers for district heating - Test procedures for establishing the performance
- SS-EN-1148-AM1 - Heat exchangers - Water to water heat exhangers for district heating - Test procedures for establishing the performance data
- SS-EN-1196 - Domestic and non-domestic gas-fired air heaters - Supplementary requirements for condensing air heaters
- SS-EN-12098-1 - Energy performance of buildings - Controls for heating systems - Part 1: Control equipment for hot water heating systems - Modules M3-5, 6, 7, 8
- SS-EN-12098-2 - Controls for heating systems - Part 2: Optimum start-stop control equipment for hot water heating systems
- SS-EN-12098-3 - Energy performance of buildings - Controls for heating systems - Part 3: Control equipment for electrical heating systems - Modules M3-5,6,7,8
- SS-EN-12098-5 - Energy Performance of Buildings - Controls for heating systems - Part 5: Start-stop schedulers for heating systems - Modules M3-5,6,7,8
- SS-EN-12170 - Heating systems in buildings - Procedure for the preparation of documents for operation, maintenance and use - Heating systems requiring a trained operator
- SS-EN-12171 - Heating systems in buildings - Procedure for the preparation of documents for operation, maintenance and use - Heating systems not requiring a trained operator
- SS-EN-12372 - Natural stone test methods - Determination of flexural strength under concentrated load
- SS-EN-1264-1 - Water based surface embedded heating and cooling systems - Part 1: Definitions and symbols
- SS-EN-1264-2 - Water based surface embedded heating and cooling systems - Part 2: Floor heating: Methods for the determination of the thermal output using calculations and experimental tests
- SS-EN-1264-3 - Water based surface embedded heating and cooling systems - Part 3: Dimensioning
- SS-EN-1264-4 - Water based surface embedded heating and cooling systems - Part 4: Installation
- SS-EN-1264-5 - Water based surface embedded heating and cooling systems - Part 5: Determination of the thermal output for wall and ceiling heating and for floor, wall and ceiling cooling
- SS-EN-12809 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods
- SS-EN-12809-AM1 - Residential independent boilers fired by solid fuel - Nominal heat output up to 50 kW - Requirements and test methods
- SS-EN-12828 - Heating systems in buildings - Design for water-based heating systems
- SS-EN-12831 - Heating systems in buildings - Method for calculation of the design heat load
- SS-EN-12831-1 - Energy performance of buildings - Method for calculation of the design heat load - Part 1: Space heating load, Module M3-3
- SS-EN-12831-3 - Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3
- SS-EN-12977-1 - Thermal solar systems and components - Custom built systems - Part 1: General requirements for solar water heaters and combisystems
- SS-EN-12977-2 - Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems
- SS-EN-12977-3 - Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores
- SS-EN-12977-4 - Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores
- SS-EN-12977-5 - Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment
- SS-EN-1302 - Chemicals used for treatment of water intended for human consumption - Aluminium-based coagulants - Analytical methods
- SS-EN-13229 - Inset appliances including open fires by solid fuels - Requirements and test methods
- SS-EN-13831 - Closed expansion vessels with built in diaphragm for installation in water
- SS-EN-13941 - Design and installation of preinsulated bonded pipe systems for district heating
- SS-EN-13941-1 - District heating pipes - Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks - Part 1: Design
- SS-EN-13941-2 - District heating pipes - Design and installation of thermal insulated bonded single and twin pipe systems for directly buried hot water networks - Part 2: Installation
- SS-EN-14037-1 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 1: Pre-fabricated ceiling mounted radiant panels for space heating - Technical specifications and requirements
- SS-EN-14037-2 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 2: Pre-fabricated ceiling mounted radiant panels for space heating - Test method for thermal output
- SS-EN-14037-3 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 3: Prefabricated ceiling mounted radiant panels for space heating - Rating method and evaluation of radiant thermal output
- SS-EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
- SS-EN-14037-5 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output
- SS-EN-14122 - Foodstuffs - Determination of vitamin B1 by high performance liquid chromatography
- SS-EN-14336 - Heating systems in buildings - Installation and commissioning of water based heating systems
- SS-EN-14337 - Heating Systems in buildings - Design and installation of direct electrical room heating systems
- SS-EN-1434-1 - Thermal energy meters - Part 1: General requirements
- SS-EN-1434-2 - Thermal energy meters - Part 2: Constructional requirements
- SS-EN-1434-4 - Thermal energy meters - Part 4: Pattern approval tests
- SS-EN-1434-5 - Thermal energy meters - Part 5: Initial verification tests
- SS-EN-1434-6 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
- SS-EN-14394 - Heating boilers - Heating boilers with forced draught burners - Nominal heat output not exceeding 10 MW and maximum operating temperature of 110 degrees Celsius
- SS-EN-14449 - Glass in building - Laminated glass and laminated safety glass - Evaluation of conformity/Product standard
- SS-EN-15036-1 - Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators
- SS-EN-15036-2 - Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 2: Flue gas noise emissions at the outlet of the heat generator
- SS-EN-15217 - Energy performance of buildings - Methods for expressing energy performance and for energy certification of buildings
- SS-EN-15232 - Energy performance of buildings - Impact of Building Automation, Controls and Building Management
- SS-EN-15232-1 - Energy performance of buildings - Part 1: Impact of Building Automation, Controls and Building Management - Modules M10-4,5,6,7,8,9,10
- SS-EN-15316-1 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 1: General and Energy performance expression, Module M3-1, M3-4, M3-9, M8-1, M8-4
- SS-EN-15316-2 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 2: Space emission systems (heating and cooling), Module M3-5, M4-5
- SS-EN-15316-2-1 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 2-1: Space heating emission systems
- SS-EN-15316-2-3 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 2-3: Space heating distribution systems
- SS-EN-15316-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 3: Space distribution systems (DHW, heating and cooling), Module M3-6, M4-6, M8-6
- SS-EN-15316-3-1 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 3.1 Domestic hot water systems, characterisation of needs (tapping requirements)
- SS-EN-15316-3-2 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 3.2: Domestic hot water systems, distribution
- SS-EN-15316-3-3 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 3.3: Domestic hot water systems, generation
- SS-EN-15316-4-1 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-1: Space heating and DHW generation systems, combustion systems (boilers, biomass), Module M3-8-1, M8-8-1
- SS-EN-15316-4-10 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-10: Wind power generation systems, Module M11-8-7
- SS-EN-15316-4-2 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
- SS-EN-15316-4-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-3: Heat generation systems, thermal solar and photovoltaic systems, Module M3-8-3, M8-8-3, M11-8-3
- SS-EN-15316-4-4 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-4: Heat generation systems, building-integrated cogeneration systems, Module M8-3-4, M8-8-4, M8-11-4
- SS-EN-15316-4-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-5: District heating and cooling, Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- SS-EN-15316-4-6 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-6: Space heating generation systems, the performance of other renewables heat and electricity
- SS-EN-15316-4-7 - Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-7: Space heating generation systems, biomass combustion systems
- SS-EN-15316-4-8 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-8: Space heating generation systems, air heating and overhead radiant heating systems, including stoves (local), Module M3-8-8
- SS-EN-15316-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 5: Space heating and DHW storage systems (not cooling), Module M3-7, M8-7
- SS-EN-15377-1 - Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 1: Determination of the design heating and cooling capacity
- SS-EN-15377-2 - Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 2: Design, dimensioning and installation
- SS-EN-15377-3 - Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 3: Optimizing for use of renewable energy sources
- SS-EN-15378 - Heating systems in buildings - Inspection of boilers and heating systems
- SS-EN-15378-1 - Energy performance of buildings - Heating systems and DHW in buildings - Part 1: Inspection of boilers, heating systems and DHW, Module M3-11, M8-11
- SS-EN-15378-3 - Energy performance of buildings - Heating and DHW systems in buildings - Part 3: Measured energy performance, Module M3-10, M8-10
- SS-EN-15417 - Gas-fired central heating boilers - Specific requirements for condensing boilers with a nominal heat input greater than 70 kW but not exceeding 1000 kW
- SS-EN-15420 - Gas-fired central heating boilers - Type C boilers of nominal heat input exceeding 70 kW, but not exceeding 1000 kW
- SS-EN-15456 - Heating boilers - Electrical power consumption for heat generators - System boundaries - Measurements
- SS-EN-15459 - Energy performance of buildings - Economic evaluation procedure for energy systems in buildings
- SS-EN-15459-1 - Energy performance of buildings - Economic evaluation procedure for energy systems in buildings - Part 1: Calculation procedures, Module M1-14
- SS-EN-15502-1 - Gas-fired heating boilers - Part 1: General requirements and tests
- SS-EN-15502-2-1 - Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
- SS-EN-15502-2-2 - Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
- SS-EN-15502-2-3 - Gas-fired central heating boilers - Part 2-3: Specific standard for hybrid units combining a gas-fired boiler and an electrical heat pump in a product
- SS-EN-16313 - Connections for heating and cooling appliances - Detachable connection with outside threaded pipe G ¾ A and inside cone
- SS-EN-16430-1 - Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
- SS-EN-16430-2 - Fan assisted radiators, convectors and trench convectors - Part 2: Test method and rating for thermal output
- SS-EN-16430-3 - Fan assisted radiators, convectors and trench convectors - Part 3: Test method and rating for cooling capacity
- SS-EN-16510-1 - Residential solid fuel burning appliances - Part 1: General requirements and test methods
- SS-EN-16510-2-1 - Residential solid fuel burning appliances - Part 2-1: Roomheaters
- SS-EN-16510-2-2 - Residential solid fuel burning appliances - Part 2-2: Inset appliances including open fires
- SS-EN-16510-2-4 - Residential solid fuel burning appliances - Part 2-4: Independent boilers - Nominal heat output up to 50 kW
- SS-EN-17082 - Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW
- SS-EN-17522 - Design and construction of backfilled and grouted borehole heat exchangers
- SS-EN-1975 - Transportable gas cylinder - Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litre
- SS-EN-215 - Thermostatic radiator valves - Requirements and test methods
- SS-EN-215-1 - Thermostatic radiator valves - Part 1: Requirements and test methods
- SS-EN-215-AM1 - Thermostatic radiator valves - Requirements and test methods
- SS-EN-26 - Gas-fired instantaneous water heaters for the production of domestic hot water
- SS-EN-297 - Gas-fired central heating boilers - Type B11 and B11BS boilers fitted with atmospheric burners of nominal heat input not exceeding 70 kW
- SS-EN-297-AM2 - Gas-fired central heating boilers - Type B11 and BS11BS boilers fitted with atmospheric burners of nominal heat input not exceeding 70 kW
- SS-EN-297-AM3 - Gas-fired central heating boilers - Type B11 and B11BS boilers fitted with atmospheric burners of nominal heat input not exceeding 70 kW - Amendment A3
- SS-EN-297-AM4 - Gas-fired central heating boilers - Type B11 and B11BS boilers, fitted with atmospheric burners of nominal heat input not exceeding 70 kW
- SS-EN-297-AM5 - Gas-fired central heating boilers - Type B11 and B11BS boilers, fitted with atmospheric burners of nominal heat input not exceeding 70 kW
- SS-EN-297-AM6 - Gas-fired central heating boilers - Type B11 and B11BS boilers, fitted with atmospheric burners of nominal heat input not exceeding 70 kW
- SS-EN-303-1 - Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking
- SS-EN-303-2 - Heating boilers - Part 2: Heating boilers with forced draught burners - Special requirements for boilers with atomizing oil burners
- SS-EN-303-3 - Heating boilers - Part 3: Gas-fired central heating boilers - Assembly comprising a boiler body and a forced draught burner
- SS-EN-303-3-AM2 - Heating Boilers - Part 3: Gas-fired heating boilers - Assembly comprising a boiler body and a forced draught burner
- SS-EN-303-5 - Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking
- SS-EN-303-6 - Heating boilers - Part 6: Heating boilers with forced draught burners - Specific requirements for the domestic hot water operation and energy performance of water heaters and combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kW
- SS-EN-303-7 - Heating boilers - Part 7: Gas-fired central heating boilers equipped with a forced draught burner of nominal heat output not exceeding 1 000 kW
- SS-EN-304 - Heating boilers - Test code for heating boilers for atomizing oil burners
- SS-EN-304-AM1 - Heating boilers - Test code for heating boilers for atomizing oil burners
- SS-EN-304-AM2 - Heating boilers - Test code for heating boilers for atomizing oil burners
- SS-EN-442-1 - Radiators and convectors - Part 1: Technical specifications and requirements
- SS-EN-442-1-AM1 - Radiators and convectors - Part 1: Technical specifications and requirements
- SS-EN-442-2 - Radiators and convectors - Part 2: Test methods and rating
- SS-EN-442-2-AM1 - Radiators and convectors - Part 2: Test methods and rating
- SS-EN-442-2-AM2 - Radiators and convectors - Part 2: Test methods and rating
- SS-EN-442-3 - Radiators and convectors - Part 3: Evaluation of conformity
- SS-EN-449 - Specification for dedicated liquefied petroleum gas appliances - Domestic flueless space heaters (including diffusive catalytic combustion heaters)
- SS-EN-483 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
- SS-EN-483-AM2 - Gas-fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
- SS-EN-483-AM4 - Gas fired central heating boilers - Type C boilers of nominal heat input not exceeding 70 kW
- SS-EN-488 - District heating pipes - Bonded single pipe systems for directly buried hot water networks - Factory made steel valve assembly for steel service pipes, polyurethane thermal insulation and a casing of polyethylene
- SS-EN-489 - District heating pipes - Preinsulated bonded pipe systems for direcly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
- SS-EN-563 - Safety of machinery - Tempertures of touchable surfaces - Ergonomics data to establish temperature limit values for hot surfaces
- SS-EN-656 - Gas-fired central heating boilers - Type B boilers of nominal heat input exceeding 70 kW but not exceeding 300 kW
- SS-EN-656-AM1 - Gas-fired central heating boilers - Type B boilers of nominal heat input exceeding 70 kW, but not exceeding 300 kW
- SS-EN-677 - Gas-fired central heating boilers - Specic requirements for condensing boilers with a nominal heat input not exceeding 70 kW
- SS-EN-832 - Thermal performance of buildings - Calculation of energy use for heating - Residential buildings
- SS-EN-834 - Heat cost allocators for the determination of the consumption of room heating radiators - Appliances with electrical energy supply
- SS-EN-835 - Heat cost allocators for the determination of theconsumption of room heating radiators - Appliances without an electrical energy supply, based on the evaporation principle
- SS-EN-89 - Gas-fired storage water heaters for the production of domestic hot water
- SS-EN-ISO-10548 - Carbon fibre - Determination of size content (ISO 10548:2002)
- SS-EN-ISO-11855-1 - Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria (ISO 11855-1:2021)
- SS-EN-ISO-11855-1-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria - Amendment 1 (ISO 11855-1:2021/Amd 1:2023)
- SS-EN-ISO-11855-2 - Building environment design - Embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity (ISO 11855-2:2021)
- SS-EN-ISO-11855-2-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity - Amendment 1 (ISO 11855-2:2021/DAM 1:2023)
- SS-EN-ISO-11855-3 - Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning (ISO 11855-3:2021)
- SS-EN-ISO-11855-3-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning - Amendment 1 (ISO 11855-3:2021/Amd 1:2023)
- SS-EN-ISO-11855-4 - Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) (ISO 11855-4:2021)
- SS-EN-ISO-11855-4-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) - Amendment 1 (ISO 11855-4:2021/Amd 1:2023)
- SS-EN-ISO-11855-5 - Building environment design - Embedded radiant heating and cooling systems - Part 5: Installation (ISO 11855-5:2021)
- SS-EN-ISO-13790 - Energy performance of buildings - Calculation of energy use for space heating and cooling (ISO 13790:2008)
- SS-EN-ISO-14419 - Textiles - Oil repellency - Hydrocarbon resistance test (ISO 14419:2010)
- SS-EN-ISO-3691-5 - Industrial trucks - Safety requirements and verification - Part 5: Pedestrian-propelled trucks (ISO 3691-5:2014)
- SS-EN-ISO-4869-2 - Acoustics - Hearing protectors - Part 2: Estimation of effective A-weighted sound pressure levels when hearing protectors are worn (ISO 4869-2:2018)
- SS-EN-ISO-52120-1 - Energy performance of buildings - Contribution of building automation, controls and building management - Part 1: General framework and procedures (ISO 52120-1:2021)
- SS-ENV-1148 - Heat exchangers - Water to water heat exchangers for district heating - Test procedures for establishing the performance data
- UNE-EN-15502-1 - Gas-fired heating boilers - Part 1: General requirements and tests
- UNE-EN-26 - Gas-fired instantaneous water heaters for the production of domestic hot water
- UNE-EN-ISO-11855-2 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity