Document Center List of Standards on Wood, Sawlogs And Sawn Timber
ICS Code 79.040
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-D1036 - Standard Test Methods of Static Tests of Wood Poles
- ASTM-D1037 - Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials
- ASTM-D1102 - Standard Test Method for Ash in Wood
- ASTM-D1105 - Standard Test Method for Preparation of Extractive-Free Wood
- ASTM-D1106 - Standard Test Method for Acid-Insoluble Lignin in Wood,
- ASTM-D1107 - Standard Test Method for Ethanol-Toluene Solubility of Wood,
- ASTM-D1108 - Standard Test Method for Dichloromethane Solubles in Wood,
- ASTM-D1109 - Standard Test Method for 1 % Sodium Hydroxide Solubility of Wood
- ASTM-D1110 - Standard Test Methods for Water Solubility of Wood
- ASTM-D1166 - Standard Test Method for Methoxyl Groups in Wood and Related Materials
- ASTM-D143 - Standard Test Methods for Small Clear Specimens of Timber
- ASTM-D1666 - Standard Test Methods for Conducting Machining Tests of Wood and Wood-Base Panel Materials
- ASTM-D1760 - Standard Specification for Pressure Treatment of Timber Products (Withdrawn 2006)
- ASTM-D1860 - Standard Test Method for Moisture and Creosote-Type Preservative in Wood (Withdrawn 2006)
- ASTM-D198 - Standard Test Methods of Static Tests of Lumber in Structural Sizes
- ASTM-D1990 - Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens
- ASTM-D2016 - Methods of Test for Moisture Content of Wood (Withdrawn 1987)
- ASTM-D2017 - Standard Test Method of Accelerated Laboratory Test of Natural Decay Resistance of Woods (Withdrawn 2014)
- ASTM-D2395 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
- ASTM-D245 - Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber
- ASTM-D2555 - Standard Practice for Establishing Clear Wood Strength Values
- ASTM-D2915 - Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products
- ASTM-D3200 - Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles
- ASTM-D3201 - Standard Test Method for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based Products
- ASTM-D4278 - Standard Practice for Wet Ashing Procedure for Preparing Wood Samples for Inorganic Chemical Analysis (Withdrawn 2006)
- ASTM-D4442 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
- ASTM-D4445 - Standard Test Method for Fungicides for Controlling Sapstain and Mold on Unseasoned Lumber (Laboratory Method)
- ASTM-D4446 - Standard Test Method for Anti-Swelling Effectiveness of Water-Repellent Formulations and Differential Swelling of Untreated Wood When Exposed to Liquid Water Environments (Withdrawn 2022)
- ASTM-D4761 - Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials
- ASTM-D5124 - Standard Practice for Testing and Use of a Random Number Generator in Lumber and Wood Products Simulation
- ASTM-D5401 - Standard Test Method for Evaluating Clear Water Repellent Coatings on Wood
- ASTM-D5536 - Standard Practice for Sampling Forest Trees for Determination of Clear Wood Properties
- ASTM-D5664 - Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber
- ASTM-D6763 - Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents
- ASTM-D6765 - Standard Practice for Live Staking
- ASTM-D6782 - Standard Test Methods for Standardization and Calibration of In-Line Dry Lumber Moisture Meters
- ASTM-D6841 - Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-Retardant-Treated Lumber
- ASTM-D7381 - Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material
- ASTM-D7438 - Standard Practice for Field Calibration and Application of Hand-Held Moisture Meters
- ASTM-D9 - Standard Terminology Relating to Wood and Wood-Based Products
- ASTM-E661 - Standard Test Method for Performance of Wood and Wood-Based Floor and Roof Sheathing Under Concentrated Static and Impact Loads
- ASTM-E69 - Standard Test Method for Combustible Properties of Treated Wood by the Fire-Tube Apparatus
- ASTM-F499 - Recommended Practice for Installation of Wood Underlayment and Preparation of the Surface to Receive Resilient Flooring (Withdrawn 1992)
BSI:
- BS-1455 - Specification for plywood manufactured from tropical hardwoods
- BS-373 - Methods of testing small clear specimens of timber
- BS-4978 - Visual strength grading of softwood. Specification
- BS-565 - Glossary of terms relating to timber and woodwork
- BS-5666-1 - Methods of analysis of wood preservatives and treated timber. Guide to sampling and preparation of wood preservatives and treated timber for analysis
- BS-5666-3 - Methods of analysis of wood preservatives and treated timber
- BS-5666-4 - Methods of analysis of wood preservatives and treated timber
- BS-5666-5 - Methods of analysis of wood preservatives and treated timber
- BS-5666-6 - Methods of analysis of wood preservatives and treated timber
- BS-5666-7 - Methods of analysis of wood preservatives and treated timber
- BS-5756 - Visual strength grading of temperate hardwood. Specification
- BS-5820 - Methods of test for determination of certain physical and mechanical properties of timber in structural sizes
- BS-6100-4.2 - Glossary of building and civil engineering terms. Forest products. Sizes and quantities of solid timber
- BS-6948 - Methods of test for mechanically fastened joints in timber and wood-based materials
- BS-EN-1001-1 - Durability of wood and wood-based products. Terminology
- BS-EN-120 - Wood based panels. Determination of formaldehyde content. Extraction method called the perforator method
- BS-EN-12490 - Durability of wood and wood-based products. Preservative-treated solid wood. Determination of the penetration and retention of creosote in treated wood
- BS-EN-1309-1 - Round and sawn timber. Method of measurement of dimensions
- BS-EN-1309-2 - Round and sawn timber. Method of measurement of dimensions
- BS-EN-1309-3 - Round and sawn timber. Methods of measurements
- BS-EN-1310 - Round and sawn timber. Method of measurement of features
- BS-EN-1311 - Round and sawn timber. Method of measurement of biological degrade
- BS-EN-1312 - Round and sawn timber. Determination of the batch volume of sawn timber
- BS-EN-1313-1 - Round and sawn timber. Permitted deviations and preferred sizes
- BS-EN-13145 - Railway applications. Track. Wood sleepers and bearers
- BS-EN-1315 - Dimensional classification of round timber
- BS-EN-1315-2 - Dimensional Classification, Softwood Round Timber
- BS-EN-1316-1 - Hardwood round timber. Qualitative classification
- BS-EN-1316-2 - Hardwood round timber. Qualitative classification
- BS-EN-13183-3 - Moisture content of a piece of sawn timber
- BS-EN-14081-1 - Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-1-TC - Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-2 - Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-2-TC - Tracked Changes. Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-3 - Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-3-TC - Tracked Changes. Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14081-4 - Timber structures. Strength graded structural timber with rectangular cross section
- BS-EN-14128 - Durability of wood and wood-based products. Efficacy criteria for curative wood preservatives as determined by biological tests
- BS-EN-14251 - Structural round timber. Test methods
- BS-EN-14298 - Sawn timber. Assessment of drying quality
- BS-EN-14298-TC - Tracked Changes. Sawn timber. Assessment of drying quality
- BS-EN-14358 - Timber structures. Calculation and verification of characteristic values
- BS-EN-14358-TC - Tracked Changes. Timber structures. Calculation and verification of characteristic values
- BS-EN-14734 - Durability of wood and wood-based products. Determination of treatability of timber species to be impregnated with wood preservatives. Laboratory method
- BS-EN-15228 - Structural timber. Structural timber preservative treated against biological attack
- BS-EN-15497 - Structural finger jointed solid timber. Performance requirements and minimum production requirements
- BS-EN-1611-1 - Sawn timber. Appearance grading of softwoods
- BS-EN-16449 - Wood and wood-based products. Calculation of the biogenic carbon content of wood and conversion to carbon dioxide
- BS-EN-16737 - Structural timber. Visual strength grading of tropical hardwood
- BS-EN-16873 - Conservation of cultural heritage. Guidelines for the management of waterlogged wood on archaeological terrestrial sites
- BS-EN-1912 - Structural Timber. Strength classes. Assignment of visual grades and species
- BS-EN-1912-TC - Tracked Changes. Structural Timber. Strength classes. Assignment of visual grades and species
- BS-EN-1927-1 - Qualitative classification of softwood round timber
- BS-EN-1927-2 - Qualitative classification of softwood round timber
- BS-EN-1927-3 - Qualitative classification of softwood round timber
- BS-EN-335 - Durability of wood and wood-based products. Use classes: definitions, application to solid wood and wood-based products
- BS-EN-335-1 - Durabiltity of wood and wood-based products. Definitions of use classes. General
- BS-EN-335-2 - Durability of wood and wood-based products. Definition of use classes. Application to solid wood
- BS-EN-335-3 - Hazard classes of wood and wood-based products against biological attack. Application to wood-based panels
- BS-EN-336 - Structural timber. Sizes, permitted deviations
- BS-EN-338 - Structural timber. Strength classes
- BS-EN-350-1 - Durability of wood and wood-based products. Natural durability of solid wood. Guide to the principles of testing and classification of natural durability of wood
- BS-EN-350-2 - Durability of wood and wood-based products. Natural durability of solid wood. Guide to natural durability and treatability of selected wood species of importance in Europe
- BS-EN-351-1 - Durability of wood and wood-based products. Preservative-treated solid wood
- BS-EN-351-1-TC - Tracked Changes. Durability of wood and wood-based products. Preservative-treated solid wood
- BS-EN-351-2 - Durability of wood and wood-based products. Preservative-treated solid wood
- BS-EN-351-2-TC - Tracked Changes. Durability of wood and wood-based products. Preservative-treated solid wood
- BS-EN-384 - Structural timber. Determination of characteristic values of mechanical properties and density
- BS-EN-385 - Finger jointed structural timber. Performance requirements and minimum production requirements
- BS-EN-408 - Timber structures. Structural timber and glued laminated timber. Determination of some physical and mechanical properties
- BS-EN-518 - Structural timber. Grading. Requirements for visual strength grading standards
- BS-EN-519 - Structural timber. Grading. Requirements for machine strength graded timber and grading machines
- BS-EN-789 - Timber structures. Test methods. Determination of mechanical properties of wood based panels
- BS-EN-844 - Round and sawn timber. Terminology
- BS-EN-844-4 - Round and sawn timber. Terminology
- BS-EN-844-5 - Round and sawn timber. Terminology
- BS-EN-844-6 - Round and sawn timber. Terminology
- BS-EN-844-7 - Round and sawn timber. Terminology
- BS-EN-844-8 - Round and sawn timber. Terminology
- BS-EN-844-9 - Round and sawn timber. Terminology
- BS-EN-942 - Timber in joinery. General requirements
- BS-EN-975-1 - Sawn timber. Appearance grading of hardwoods
- BS-EN-975-2 - Sawn timber. Appearance grading of hardwoods
- BS-ISO-13061-18 - Physical and mechanical properties of wood. Test methods for small clear wood specimens
- BS-ISO-13061-5 - Physical and mechanical properties of wood. Test methods for small clear wood specimens
- BS-ISO-13061-8 - Physical and mechanical properties of wood. Test methods for small clear wood specimens.
- BS-ISO-22157 - Bamboo structures. Determination of physical and mechanical properties of bamboo culms. Test methods
- BS-ISO-24294 - Timber. Round and sawn timber. Vocabulary
- BS-ISO-3129 - Wood. Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens
- DD-257-1 - Methods of analysis of wood preservatives and treated timber. Quantitative analysis of wood preservative solutions and treated timber containing boron compounds. Determination of total boron
- DD-257-2 - Methods of analysis of wood preservatives and treated timber
- DD-257-3 - Methods of analysis of wood preservatives and treated timber
- DD-257-4 - Methods of analysis of wood preservatives and treated timber
- DD-257-5 - Methods of analysis of wood preservatives and treated timber
- DD-CEN-12169 - Criteria for the assessment of conformity of a lot of sawn timber
- DD-CEN-14464 - Sawn timber. Method for assessment of case-hardening
- DD-CEN-15083-1 - Durability of wood and wood-based products. Determination of the natural durability of solid wood against food-destroying fungi, test methods
- DD-CEN-15083-2 - Durability of wood and wood-based products. Determination of the natural durability of solid wood against wood-destroying fungi, test methods
- DD-CEN-15679 - Thermal modified timber. Definitions and characteristics
- DD-ENV-12169 - Criteria for the assessment of conformity of a lot of sawn timber
- DD-ENV-14464 - Sawn Timber, Method for Assessment of Case-Hardening
- DD-ENV-1927-3 - Part 3: Larches & Douglas Firs
- PAS-2021 - Exercising due diligence in establishing the legal origin of timber and timber products. Guide to Regulation (EU) No 995/2010
- PD-CEN-14734 - Durability of wood and wood-based products. Determination of treatability of timber species to be impregnated with wood preservatives. Laboratory method
- PD-CEN-14823 - Durability of wood and wood-based products. Quantitative determination of pentachlorophenol in wood. Gas chromatographic method
- PD-CEN-15003 - Durability of wood and wood-based products. Criteria for hot air processes for curative uses against wood destroying organisms
- PD-ISO-21141 - Timber structures. Timber connections and assemblies. Determination of yield and ultimate characteristics and ductility from test data
ISO:
- ISO-1029 - Coniferous sawn timber -- Defects -- Classification
- ISO-1030 - Coniferous sawn timber -- Defects -- Measurement
- ISO-1031 - Coniferous sawn timber -- Defects -- Terms and definitions
- ISO-1032 - Coniferous sawn timber -- Sizes -- Terms and definitions
- ISO-13059 - Round timber - Requirements for the measurement of dimensions and methods for the determination of volume
- ISO-13061-1 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 1: Determination of moisture content for physical and mechanical tests
- ISO-13061-10 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 10: Determination of impact bending strength
- ISO-13061-11 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 11: Determination of resistance to impact indentation
- ISO-13061-12 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 12: Determination of static hardness
- ISO-13061-13 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 13: Determination of radial and tangential shrinkage
- ISO-13061-14 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 14: Determination of volumetric shrinkage
- ISO-13061-15 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 15: Determination of radial and tangential swelling
- ISO-13061-16 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 16: Determination of volumetric swelling
- ISO-13061-17 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 17: Determination of ultimate stress in compression parallel to grain
- ISO-13061-18 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 18: Vocabulary
- ISO-13061-1-AM1 - - Amendment 1
- ISO-13061-2 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 2: Determination of density for physical and mechanical tests
- ISO-13061-2-AM1 - - Amendment 1
- ISO-13061-3 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 3: Determination of ultimate strength in static bending
- ISO-13061-3-AM1 - - Amendment 1
- ISO-13061-4 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 4: Determination of modulus of elasticity in static bending
- ISO-13061-4-AM1 - - Amendment 1
- ISO-13061-5 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 5: Determination of strength in compression perpendicular to grain
- ISO-13061-6 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 6: Determination of ultimate tensile stress parallel to grain
- ISO-13061-7 - Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 7: Determination of ultimate tensile stress perpendicular to grain
- ISO-13912 - Structural timber - Machine strength grading - Basic principles
- ISO-16415 - Non-structural timber grading requirements
- ISO-17959 - General requirements for solid wood flooring
- ISO-19474 - Round timber - Visual characteristics - Methods of determination
- ISO-21625 - Vocabulary related to bamboo and bamboo products
- ISO-21887 - Durability of wood and wood-based products - Use classes
- ISO-22157 - Bamboo structures - Determination of physical and mechanical properties of bamboo culms - Test methods
- ISO-22157-1 - Bamboo - Determination of physical and mechanical properties - Part 1: Requirements
- ISO-22157-2 - Bamboo - Determination of physical and mechanical properties - Part 2: Laboratory manual
- ISO-2299 - Sawn timber of broadleaved species -- Defects -- Classification
- ISO-2300 - Sawn timber of broadleaved species -- Defects -- Terms and definitions
- ISO-2301 - Sawn timber of broadleaved species -- Defects -- Measurement
- ISO-23066 - Vocabulary related to rattan materials and products
- ISO-23067 - Grading system for rattan: Requirements and classification
- ISO-24294 - Timber - Round and sawn timber - Vocabulary
- ISO-3129 - Wood - Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens
- ISO-3130 - Wood -- Determination of moisture content for physical and mechanical tests
- ISO-3131 - Wood -- Determination of density for physical and mechanical tests
- ISO-3132 - Wood -- Testing in compression perpendicular to grain
- ISO-3133 - Wood -- Determination of ultimate strength in static bending
- ISO-3179 - Coniferous sawn timber -- Nominal dimensions
- ISO-3345 - Wood -- Determination of ultimate tensile stress parallel to grain
- ISO-3346 - Wood -- Determination of ultimate tensile stress perpendicular to grain
- ISO-3347 - Wood -- Determination of ultimate shearing stress parallel to grain
- ISO-3348 - Wood -- Determination of impact bending strength
- ISO-3349 - Wood -- Determination of modulus of elasticity in static bending
- ISO-3350 - Wood -- Determination of static hardness
- ISO-3351 - Wood -- Determination of resistance to impact indentation
- ISO-4469 - Wood -- Determination of radial and tangential shrinkage
- ISO-4470 - Sawn timber -- Determination of the average moisture content of a lot
- ISO-4471 - Wood -- Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands
- ISO-4472 - Coniferous and broadleaved sawn timber -- Transportation packages
- ISO-4475 - Coniferous and broadleaved tree sawlogs -- Visible defects -- Measurement
- ISO-4858 - Wood -- Determination of volumetric shrinkage
- ISO-4859 - Wood -- Determination of radial and tangential swelling
- ISO-4860 - Wood -- Determination of volumetric swelling
- ISO-737 - Coniferous sawn timber -- Sizes -- Methods of measurement
- ISO-738 - Coniferous sawn timber - Sizes - Permissible deviations and shrinkage
- ISO-8903 - Broadleaved sawn timber - Nominal sizes
- ISO-8904 - Broadleaved sawn timber -- Sizes -- Methods of measurement
- ISO-8905 - Sawn timber -- Test methods -- Determination of ultimate strength in shearing parallel to grain
- ISO-8906 - Sawn timber -- Test methods -- Determination of resistance to local transverse compression
- ISO-9086-1 - Wood -- Methods of physical and mechanical testing -- Vocabulary -- Part 1 : General concepts and macrostructure
- ISO-9709 - Structural timber - Visual strength grading - Basic principles
- ISO/DIS-13912.2 - Structural Timber - Machine Strength Grading - Basic Principles
- ISO/DIS-9709.2 - Structural Timber - Visual Strength Grading - Basic Principles
Other SDOs:
- DIN-EN-1309-2 - Part 2: Round Timber - Requirements for Measurement & Volume Calculation Rules, Round
- DIN-EN-13183-3 - Part 3: Estimation by Capacitance Method, Moisture Content of a Piece of Sawn Timber
- DIN-EN-14081-1 - Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements; German version EN 14081-1:2016
- DIN-EN-14081-2 - Timber structures - Strength graded structural timber with rectangular cross section - Part 2: Machine grading; additional requirements for initial type testing; German version EN 14081-2:2010+A1:2012
- DIN-EN-14081-3 - Timber structures - Strength graded structural timber with rectangular cross section - Part 3: Machine grading; additional requirements for factory production control
- DIN-EN-14081-4 - Timber structures - Strength graded structural timber with rectangular cross section - Part 4: Machine grading - Grading machine settings for machine controlled systems; German version EN 14081-4:2009
- DIN-EN-14298 - Sawn Timber, Assessment of Drying Quality
- DIN-EN-14358 - Timber structures - Calculation and verification of characteristic values; German version EN 14358:2016
- DIN-EN-1912 - Structural timber - Strength classes - Assignment of visual grades and species; German version EN 1912:2012 + AC:2013
- DIN-EN-335-1 - Durability of wood and wood-based products - Definition of use classes - Part 1: General
- DIN-EN-335-2 - Durability of wood and wood-based products - Definition of use classes - Part 2: Application to solid wood; German version EN 335-2:2006
- DIN-EN-336 - Structural timber - Sizes, permitted deviations; German version EN 336:2013
- DIN-EN-338 - Structural timber - Strength classes; German version EN 338:2016
- DIN-EN-384 - Structural timber - Determination of characteristic values of mechanical properties and density; German version EN 384:2016
- DIN-EN-408 - Timber structures - Structural timber and glued laminated timber - Determination of some physical and mechanical properties; German version EN 408:2010+A1:2012
- DIN-EN-942 - Timber in Joinery - General Requirements
- DIN-EN-975-2 - Part 2: Poplars, Sawn Timber, Appearance Grading of Hardwoods
- DIN-ISO-15228 - Textile Machinery & Accessories - Profile Reeds for Air Jet Weaving Machines - Dimens
- EN-12490 - Durability of Wood & Wood-Based Products - Preservative-Treated Solid Wood - Determina
- EN-1309-1 - Round & Sawn Timber, Method of Measurement of Dimensions, Sawn Timber
- EN-1309-2 - Part 2: Round Timber - Requirements for Measurement & Volume Calculation Rules, Round
- EN-1310 - Round & Sawn Timber, Method of Measurement of Features
- EN-1311 - Round & Sawn Timber, Method of Measurement of Biological Degrade
- EN-1312 - Round & Sawn Timber, Determination of the Batch Volume of Sawn Timber
- EN-1313-1 - Part 1: Softwood Sawn Timber, Round & Sawn Timber - Permitted Deviations & Preferred S
- EN-1315 - Dimensional Classification of Round Timber
- EN-1315-2 - Dimensional Classification, Softwood Round Timber
- EN-1316-1 - Hardwood round timber - Qualitative classification - Part 1: Oak and beech
- EN-1316-2 - Hardwood round timber - Qualitative classification - Part 2: Poplar
- EN-13183-3 - Part 3: Estimation by Capacitance Method, Moisture Content of a Piece of Sawn Timber
- EN-14081-1 - Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements
- EN-14081-2 - Timber structures - Strength graded structural timber with rectangular cross section - Part 2: Machine grading; additional requirements for initial type testing
- EN-14081-3 - Timber structures - Strength graded structural timber with rectangular cross section - Part 3: Machine grading; additional requirements for factory production control
- EN-14251 - Structural Round Timber, Test Methods
- EN-14298 - Sawn timber - Assessment of drying quality
- EN-14358 - Timber structures - Calculation and verification of characteristic values
- EN-15228 - Structural Timber, Structural Timber Preservative Treated Against Biological Attack
- EN-15497 - Structural finger jointed solid timber - Performance requirements and minimum production requirements
- EN-16449 - Wood and wood-based products - Calculation of the biogenic carbon content of wood and conversion to carbon dioxide
- EN-16737 - Structural timber - Visual strength grading of tropical hardwood
- EN-16873 - Conservation of cultural heritage - Guidelines for the management of waterlogged wood on archaeological terrestrial sites
- EN-1912 - Structural Timber - Strength classes - Assignment of visual grades and species
- EN-1927-1 - Qualitative Classification of Softwood Round Timber, Spruce & Firs
- EN-1927-2 - Part 2: Pines, Qualitative Classification of Softwood Round Timber
- EN-335 - Durability of wood and wood-based products - Use classes: definitions, application to solid wood and wood-based products
- EN-336 - Structural timber - Sizes, permitted deviations
- EN-338 - Structural timber - Strength classes
- EN-350 - Durability of wood and wood-based products - Testing and classification of the durability to biological agents of wood and wood-based materials
- EN-384 - Structural timber - Determination of characteristic values of mechanical properties and density
- EN-385 - Finger-Jointed Structural Timber, Performance Requirements & Minimum Production Requir
- EN-408 - Timber structures - Structural timber and glued laminated timber - Determination of some physical and mechanical properties
- EN-789 - Timber Structures - Test Methods, Determiantion of Mechanical Properties of Wood-Based
- EN-844-5 - Round & Sawn Timber, Terminology, Terms Relating To Dimensions of Round Timber
- EN-844-6 - Round & Sawn Timber, Terminology, Terms Relating To Dimensions of Sawn Timber
- EN-844-7 - Round & Sawn Timber, Terminology, Terms Relating To Anatomical Structure of Timber
- EN-844-8 - Round & Sawn Timber, Terminology, Terms Relating To Features of Round Timber
- EN-844-9 - Round & Sawn Timber, Terminology, Terms Relating To Features of Sawn Timber
- EN-942 - Timber in Joinery - General Requirements
- EN-975-1 - Sawn timber - Appearance grading of hardwoods - Part 1: Oak and beech
- EN-975-2 - Part 2: Poplars, Sawn Timber, Appearance Grading of Hardwoos
- SIS-232711 - Sawn timber - Dimensions
- SIS-CEN/TR-16420 - Analytical Method for the Analysis of Propiconazole in treated Wood Samples
- SIS-CEN/TR-17809 - Durability of wood and wood-based products - Remedial treatment of wood against insects by injection
- SIS-CEN/TR-17810 - Durability of wood and wood-based products - Interpretation document for standards related to efficacy requirements and specifications of wood preservatives
- SIS-CEN/TS-12169 - Criteria for the assessment of conformity of a lot of sawn timber
- SIS-CEN/TS-15679 - Thermal Modified Timber - Definitions and characteristics
- SS-232712 - Timber - Planed timber - Thickness and width
- SS-EN-1001-1 - Durability of wood and wood-based products - Terminology - Part 1: List of equivalent terms
- SS-EN-1058 - Wood-based panels - Determination of characteristic 5-percentile values and characteristic mean values
- SS-EN-1193 - Timber structures - Structural timber and glued laminated timber - Determination of shear strength and mechanical properties perpendicular to grain
- SS-EN-120 - Wood-based panels - Determination of formaldehydecontent - Extraction method called the perforatormethod
- SS-EN-12490 - Durability of wood and wood-based products - Preservative-treated solid wood - Determination of the penetration and retention of creosote in treated wood
- SS-EN-12639 - Liquid pumps and pump units - Noise test code - Grade 2 and grade 3 of accuracy
- SS-EN-13024-1 - Glass in building - Thermally toughened borosilicate safety glass - Part 1: Definition and description
- SS-EN-1309-2 - Round and sawn timber - Method of measurement of dimensions - Part 2: Round timber - Requirements for measurement and volume calculation rules
- SS-EN-1309-3 - Round and sawn timber - Methods of measurements - Part 3: Features and biological degradations
- SS-EN-1312 - Round and sawn timber - Determination of the batch volume of sawn timber
- SS-EN-1313-1 - Round and sawn timber - Permitted deviations and preferred sizes - Part 1: Softwood sawn timber
- SS-EN-1313-2 - Round and sawn timber - Permitted deviations and preferred sizes - Part 2: Hardwood sawn timber
- SS-EN-13145 - Railway applications - Track - Wood sleepers and bearers
- SS-EN-1315 - Dimensional classification of round timber
- SS-EN-1315-1 - Dimensional classification - Part 1: Hardwood round timber
- SS-EN-1315-2 - Dimensional classification - Part 2: Softwood round timber
- SS-EN-1316-1 - Hardwood round timber - Qualitative classification - Part 1: Oak and beech
- SS-EN-1316-2 - Hardwood round timber - Qualitative classification - Part 2: Poplar
- SS-EN-1316-3 - Hardwood round timber - Quality classification - Part 3: Ash and maples and sycamore
- SS-EN-13183-1 - Moisture content of a piece of sawn timber - Part 1: Determination by oven dry method
- SS-EN-13183-2 - Moisture content of a piece of sawn timber - Part 2: Estimation by electrical resistance method
- SS-EN-13183-3 - Moisture content of a piece of sawn timber - Part 3: Estimation by capacitance method
- SS-EN-13556 - Round and sawn timber - Nomenclature of timbers used in Europe
- SS-EN-13706-2 - Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements
- SS-EN-13706-3 - Reinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements
- SS-EN-13980 - Potentially explosive atmospheres - Application of quality systems
- SS-EN-14080 - Timber structures - Glued laminated timber and glued solid timber - Requirements
- SS-EN-14081-1 - Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements
- SS-EN-14081-2 - Timber structures - Strength graded structural timber with rectangular cross section - Part 2: Machine grading; additional requirements for type testing
- SS-EN-14081-3 - Timber structures - Strength graded structural timber with rectangular cross section - Part 3: Machine grading; additional requirements for factory production control
- SS-EN-14081-4 - Timber structures - Strength graded structural timber with rectangular cross section - Part 4: Machine grading - Grading machine settings for machine controlled systems
- SS-EN-14096-2 - Non-destructive testing - Qualification of radiographic film digitisation systems - Part 2: Minimum requirements
- SS-EN-14128 - Durability of wood and wood-based products - Efficacy criteria for curative wood preservatives as determined by biological tests
- SS-EN-14251 - Structural round timber - Test methods
- SS-EN-14298 - Sawn timber - Assessment of drying quality
- SS-EN-14358 - Timber structures - Calculation and verification of characteristic values
- SS-EN-1438 - Symbols for timber and wood-based products
- SS-EN-14734 - Durability of wood and wood-based products - Determination of treatability of timber species to be impregnated with wood preservatives - Laboratory method
- SS-EN-15228 - Structural timber - Structural timber preservative treated against biological attack
- SS-EN-15497 - Structural finger jointed solid timber - Performance requirements and minimum production requirements
- SS-EN-16449 - Wood and wood-based products - Calculation of the biogenic carbon content of wood and conversion to carbon dioxide
- SS-EN-16737 - Structural timber - Visual strength grading of tropical hardwood
- SS-EN-16873 - Conservation of cultural heritage - Guidelines for the management of waterlogged wood on archaeological terrestrial sites
- SS-EN-1912 - Structural Timber - Strength classes - Assignment of visual grades and species
- SS-EN-1927-1 - Qualitative classification of softwood round timber Part 1 : Spruces and firs
- SS-EN-1927-2 - Qualitative classification of softwood round timber - Part 2 : Pines
- SS-EN-1927-3 - Qualitative classification of softwood round timber - Part 3 : Larches and douglas firs
- SS-EN-310 - Wood-based panels - Determination of modulus of elasticity in bending and of bending strength
- SS-EN-325 - Wood-based panels - Determination of dimensions of test pieces
- SS-EN-335 - Durability of wood and wood-based products - Use classes: definitions, application to solid wood and wood-based products
- SS-EN-336 - Structural timber - Sizes, permitted deviations
- SS-EN-338 - Structural timber - Strength classes
- SS-EN-350 - Durability of wood and wood-based products - Testing and classification of the durability to biological agents of wood and wood-based materials
- SS-EN-350-1 - Durability of wood and wood-based products - Natural durability of solid wood - Part 1: Guide to the principles of testing and classification of the natural durability of wood
- SS-EN-350-2 - Durability of wood and wood-based products - Natural durability of solid wood - Part 2: Guide to natural durability and treatability of selected wood species of importance in Europe
- SS-EN-351-1 - Durability of wood and wood-based products - Preservative-treated solid wood- Part 1 Classification of preservative penetration and retention
- SS-EN-351-2 - Durability of wood and wood-based products-Preservative-treated solid wood- Part 2 Guidance on sampling for the analysis of preservative-treated wood
- SS-EN-384 - Structural timber - Determination of characteristic values of mechanical properties and density
- SS-EN-385 - Finger jointed structural timber - Performance requirements and minimum production requirements
- SS-EN-386 - Glued laminated timber - Performance requirements and minimum production requirements
- SS-EN-391 - Glued laminated timber - Delamination test of glue lines
- SS-EN-408 - Timber structures - Structural timber and glued laminated timber - Determination of some physical and mechanical properties
- SS-EN-460 - Durability of wood and wood-based products - Natural durability of solid wood - Guide to the durability requirements for wood to be used in hazard classes
- SS-EN-594 - Timber structures - Test methods - Racking strength and stiffness of timber frame wall panels
- SS-EN-595 - Timber structures - Test methods - Test of trusses for the determination of strength and deformation behavior
- SS-EN-596 - Timber structures - Test methods - Soft body impact test of timber framed walls
- SS-EN-789 - Timber structures - Test methods - Determination of mechanical properties of wood based panels
- SS-EN-844 - Round and sawn timber - Terminology
- SS-EN-942 - Timber in joinery - General requirements
- SS-EN-975-1 - Sawn timber - Appearance grading of hardwoods - Part 1: Oak and beech
- SS-EN-975-2 - Sawn timber - Appearance grading of hardwoods - Part 2: Poplars
- SS-EN-ISO-105-X16 - Textiles - Tests for colour fastness - Part X16: Colour fastness to rubbing - Small areas (ISO 105-X16:2016)
- SS-EN-ISO-1119 - Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011)
- SS-EN-ISO-12460-5 - Wood-based panels - Determination of formaldehyde release - Part 5: Extraction method (called the perforator method) (ISO 12460-5:2015)
- SS-EN-ISO-3715-2 - Ships and marine technology - Propulsion plants for ships - Part 2: Vocabulary for controllable-pitch propeller plants (ISO 3715-2:2001)
- SS-ENV-14464 - Sawn timber - Method for assessment of case-hardening
- SS-ENV-1995-1-2 - Eurocode 5: Design of timber structures - Part 1-2: General rules - Structural fire design
- SS-ISO-15873 - Irrigation equipment - Differential pressure Venturi-type liquid additive injectors
- SS-ISO-1746 - Rubber or plastics hoses and tubing - Bending tests - Technical Corrigendum 1
- SS-ISO-8903 - Broadleaved sawn timber - Nominal sizes (ISO 8903:2016, IDT)
- UNE-EN-14081-1 - Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements