Document Center List of Standards on Non-Ferrous Alloys In General
ICS Code 49.025.15
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-E1558 - Standard Guide for Electrolytic Polishing of Metallographic Specimens
- ASTM-F482 - Standard Practice for Corrosion of Aircraft Metals by Total Immersion in Maintenance Chemicals
- ASTM-F483 - Standard Practice for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals
BSI:
- BS-2B-25 - Copper-nickel-silicon alloy rods, sections, forging stock, forgings and parts (heat treated)
- BS-2B-26 - Copper-nickel-silicon alloy rods, sections and parts (solution treated, cold worked and precipitation treated)
- BS-2B-28 - Copper-Beryllium Alloy Strip, Foil & Parts (Solution Treated, Cold Worked & Precipitat
- BS-2B-29 - Copper-Beryllium Alloy Strip, Foil & Parts (Solution Treated, Cold Rolled: Quarter Har
- BS-2B-30 - Copper-Beryllium Alloy Strip, Foil & Parts (Solution Treated, Cold Rolled: Half Hard &
- BS-2B-31 - Copper-Beryllium Alloy Strip, Foil & Parts (Solution Treated, Cold Rolled: Full Hard &
- BS-2B-32 - Copper-Beryllium Alloy Rods, Sections & Parts (Solution Treated & Precipitation Treate
- BS-2B-33 - Copper-beryllium alloy wire and springs (solution treated and precipitation treated)
- BS-3B-25 - Specification for copper-nickel-silicon alloy rods, bars, sections, forging stock and forgings (heat treated)
- BS-3B-26 - Specification for copper-nickel-silicon alloy rods, bars and sections (solution treated, cold worked and precipitation treated)
- BS-3B-28 - Specification for copper-beryllium alloy strip and foil (solution treated and precipitation treated)
- BS-3B-29 - Specification for copper-beryllium alloy strip and foil (solution treated, cold rolled: quarter hard and precipitation treated)
- BS-3B-30 - Specification for copper-beryllium alloy strip and foil (solution treated, cold rolled: half hard and precipitation treated)
- BS-3B-31 - Specification for copper-beryllium alloy strip and foil (solution treated, cold rolled: full hard and precipitation treated)
- BS-3B-32 - Specification for copper-beryllium alloy rods, bars and sections (solution treated and precipitation treated)
- BS-3B-33 - Specification for copper-beryllium alloy wire(solution treated and precipitation treated)
- BS-EN-2002-16 - Aerospace series. Metallic materials. Test methods
- BS-EN-2002-2 - Aerospace series. Metallic materials. Test methods
- BS-EN-2002-21 - Aerospace series. Metallic materials. Test methods
- BS-EN-2032-001 - Aerospace series. Metallic materials
- BS-EN-2032-1 - Metallic materials. Conventional designation
- BS-EN-2043 - Aerospace series. Metallic materials. General requirements for semi-finished product qualification (excluding forgings and castings)
- BS-EN-2078 - Aerospace series. Metallic materials. Manufacturing schedule, inspection schedule, inspection and test report. Definition, general principles, preparation and approval
- BS-EN-2306 - Aerospace series. Heat resisting. Nickel base alloy Ni-Cr20Co3Fe3. Annealed. Bars
- BS-EN-2400 - Aerospace series. Heat resisting nickel base alloy NI-P96-HT. Cold drawn and precipitation treated. Wire. D 10 mm
- BS-EN-2402 - Aerospace series. Heat resisting nickel base alloy NiCr20Co3Fe3. Annealed. Wire. D 10 mm
- BS-EN-2600 - Aerospace series. Designation of metallic semi-finished products. Rules
- BS-EN-2731 - Aerospace series. Magnesium alloy MG-C46001. T6. Sand casting
- BS-EN-2732 - Magnesium alloy MG-C46001-T6. Chill casting
- BS-EN-2959 - Aerospace series. Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al). Solution treated and cold worked. Bar for forged fasteners. 3 mm D 30 mm
- BS-EN-2960 - Aerospace series. Heat resisting nickel base alloy (NI- P101HT). Cold worked and solution treated. Bars for machining for fasteners. 3 mm D 50 mm
- BS-EN-3018 - Aerospace series. Heat resisting alloy NI-PH2801 (NiCr16Fe7Ti3Nb1Al1). Consumable electrode remelted. Cold drawn wire for the manufacture of thread inserts. D 3 mm
- BS-EN-3668 - Aerospace series. Heat resisting alloy NI-PH2301 (NiCr21Fe18Mo9). Non heat treated. Forging stock. a or D 250 mm
- BS-EN-3844-1 - Aerospace series. Flammability of non-metallic materials
- BS-EN-3844-3 - Aerospace series. Flammability of non-metallic materials
- BS-EN-3875 - Aerospace series. Metallic materials, Filler metal for brazing. Technical specification
- BS-EN-3879 - Aerospace series. Metallic materials. Filler metal for welding. Technical specification
- BS-EN-3882 - Aerospace series. Heat resisting alloy NI-WH1801 (NiCr20Co18Ti3Al2). Filler wire for welding
- BS-EN-3883 - Aerospace series. Heat resisting alloy NI-WH2301 (NiCr22Fe19Mo9Co2). Filler metal for welding
- BS-EN-3884 - Aerospace series. Heat resisting alloy NI-WH2601 (NiCr19Nb5Mo3Ti). Filler metal for welding
- BS-EN-3885 - Aerospace series. Heat resisting alloy NI-WH3601 (NiCr22Mo9Nb4). Filler metal for welding
- BS-EN-3886 - Aerospace series. Heat resisting alloy NI-WH1303 (NiCo20Cr20Mo5Ti2Al). Filler metal for welding
- BS-EN-3887 - Aerospace series. Heat resisting alloy CO-WH4101 (CoCr20W15Ni). Filler metal for welding
- BS-EN-3888 - Aerospace series. Heat resisting alloy CO-WH1402 (CoCr22Ni22W15). Filler metal for welding
- BS-EN-3894 - Aerospace series. Heat resisting alloy NI-WD3201 (NiMo25Fe6Cr5). Filler metal for welding
- BS-EN-3895 - Aerospace series. Heat resisting alloy NI-WH3901 (NiCr16Mo15). Filler metal for welding
- BS-EN-3920 - Aerospace series. Nickel base alloy NI-B41202 (NiCr14Fe5Si5B3). Filler metal for brazing. Powder or paste
- BS-EN-3921 - Aerospace series. Nickel base alloy NI-B41203 (NiCr7Si5B3). Filler metal for brazing. Amorphous foil
- BS-EN-3923 - Aerospace series. Nickel base alloy NI - B41203 (NiCr7Si5B3Fe3). Filler metal for brazing. Powder or paste
- BS-EN-3925 - Aerospace series. Nickel base alloy NI-B40001 (NiSi5B3). Filler metal for brazing. Amorphous foil
- BS-EN-3926 - Aerospace series. Nickel base alloy NI-B40001 (NiSi5B3). Filler metal for brazing. Borided foil
- BS-EN-3927 - Aerospace series. Nickel base alloy NI-B40001 (NiSi5B3). Filler metal for brazing. Powder or paste
- BS-EN-3930 - Aerospace series. Nickel base alloy NI-B31001 (NiCr19Si10). Filler metal for brazing. Powder or paste
- BS-EN-3932 - Aerospace series. Nickel base alloy NI-B13001 (NiP11). Filler metal for brazing. Amorphous foil
- BS-EN-3933 - Aerospace series. Nickel base alloy NI-B13001 (NiP11). Filler metal for brazing. Powder or paste
- BS-EN-3934 - Aerospace series. Nickel base alloy NI-B21001 (NiCr15B4). Filler metal for brazing. Amorphous foil
- BS-EN-3935 - Aerospace series. Nickel base alloy NI-B21001 (NiCr15B4). Filler metal for brazing. Borided foil
- BS-EN-3936 - Aerospace series. Nickel base alloy NI-B21001 (NiCr15B4). Filler metal for brazing. Powder or paste
- BS-EN-3937 - Aerospace series. Nickel base alloy NI-B44101 (NiW12Cr10Si4Fe3B3). Filler metal for brazing. Powder or paste
- BS-EN-3938 - Aerospace series. Nickel base alloy NI-B46001 (NiCo20Si5B3) Filler metal for brazing. Amorphous foil
- BS-EN-3939 - Aerospace series. Nickel base alloy NI-B46001 (NiCo20Si5B3). Filler metal for brazing. Powder or paste
- BS-EN-3941 - Aerospace series. Nickel base alloy NI-B41204 (NiCr13Si4B3). Filler metal for brazing. Amorphous foil
- BS-EN-3942 - Aerospace series. Nickel base alloy NI-B41204 (NiCr13Si4B3). Filler metal for brazing. Borided foil
- BS-EN-3943 - Aerospace series. Nickel base alloy NI-B41204 (NiCr13Fe4Si4B3). Filler metal for brazing. Powder or paste
- BS-EN-3945 - Aerospace series. Nickel base alloy NI-B48801 (NiMn19Si6Cu4B). Filler metal for brazing. Powder or paste
- BS-EN-3946 - Aerospace series. Nickel base alloy NI-B15701 (NiPd34Au30). Filler metal for brazing. Powder or paste
- BS-EN-3952 - Aerospace series. Silver base alloy AG-B10001 (AgCu28). Filler metal for brazing. Wire
- BS-EN-3953 - Aerospace series. Silver base alloy AG-B12401 (AgCu40Zn5Ni). Filler metal for brazing. Wire
- BS-EN-3954 - Aerospace series. Silver base alloy AG-B12401 (AgCu40Zn5Ni). Filler metal for brazing. Powder or paste
- BS-EN-3955 - Aerospace series. Silver base alloy AG-B12401 (AgCu40Zn5Ni). Filler metal for brazing. Rolled foil
- BS-EN-3956 - Aerospace series. Silver base alloy AG-B14001 (AgCu42Ni2). Filler metal for brazing. Wire
- BS-EN-3957 - Aerospace series. Silver base alloy AG-B14001 (AgCu42Ni2). Filler metal for brazing. Powder or paste
- BS-EN-3958 - Aerospace series. Silver base alloy AG-B14001 (AgCu42Ni2). Filler metal for brazing. Rolled foil
- BS-EN-3959 - Aerospace series. Cobalt base alloy CO-B41601 (CoCr19Ni17Si8W4). Filler metal for brazing. Powder or paste
- BS-EN-3961 - Aerospace series. Gold base alloy AU-B4000. Filler metal for brazing. Rolled foil
- BS-EN-3962 - Aerospace series. Gold base alloy AU-B40001. Filler metal for brazing. Wire
- BS-EN-3963 - Aerospace series. Copper CU-BU9001. Filler metal for brazing. Rolled foil
- BS-EN-3964 - Aerospace series. Copper CU-BU9001. Filler metal for brazing. Wire
- BS-EN-4000 - Aerospace series. Metallic materials. Rules for the drafting and presentation of dimensional standards for metallic semi-finished products
- BS-EN-4050-1 - Aerospace series. Test method for metallic materials. Ultrasonic inspection of bars, plates, forging stock and forgings
- BS-EN-4050-2 - Aerospace series. Test method for metallic materials. Ultrasonic inspection of bars, plates, forging stock and forgings
- BS-EN-4050-3 - Aerospace series. Test method for metallic materials. Ultrasonic inspection of bars, plates, forging stock and forgings
- BS-EN-4050-4 - Aerospace series. Test method for metallic materials. Ultrasonic inspection of bars, plates, forging stock and forgings
- BS-EN-4060 - Aerospace series. Filler rods and filler wires for welding in heat resisting alloys. Diameter 0,5 mm D 5,0 mm. Dimensions
- BS-EN-4085 - Aerospace series. Nickel base alloy NI-B40002 (NiSi4B2). Filler metal for brazing. Amorphous foil
- BS-EN-4103 - Aerospace series. Nickel base alloy NI-B40002 (NiSi4B2). Filler metal for brazing. Borided foil
- BS-EN-4250 - Aerospace series. Nickel base alloys NI-B41001 (NiCr19Si7B). Filler metal for brazing. Amorphous foil
- BS-EN-4259 - Aerospace series. Metallic materials. Definition of general terms
- BS-EN-4260 - Aerospace series. Metallic materials. Rules for drafting and presentation of technical specifications
- BS-EN-4261 - Aerospace series. Metallic materials. Rules for drafting and presentation of test method standards
- BS-EN-4268 - Aerospace series. Metallic materials. Heat treatment facilities. General requirements
- BS-EN-4325 - Aerospace series. Heat resisting alloy NI-WH1302 (NiCr20Co13Mo4Ti3AI). Filler metal for welding. Wire and rod
- BS-EN-4326 - Aerospace series. Heat resisting alloy CO-WH4102 (CoCr28W20Ni5V1). Filler metal for welding. Wire and rod
- BS-EN-4329 - Aerospace series. Heat resisting alloy NI-WH0001 (NiCr20). Filler metal for welding. Wire and rod
- BS-EN-4337 - Aerospace series. Heat resisting alloy NI-WH8901 (NiCr16Ti3Mn2). Filler metal for welding. Wire and rod
- BS-EN-4338 - Aerospace series. Heat resisting alloy. NI-WH3902 (NiCr25Mo10C). Filler metal for welding. Wire and rod
- BS-EN-4339 - Aerospace series. Heat resisting alloy CO-WH4001 (CoCr29W9). Filler metal for welding. Wire and rod
- BS-EN-4340 - Aerospace series. Magnesium alloy MG-W68001. Filler metal for welding. Wire and rod
- BS-EN-4372 - Aerospace series. Heat resisting nickel alloy with copper NI-PD9001 (NiCu31). Wire for solid rivets. D 10 mm
- BS-EN-4373 - Aerospace series. Heat resisting alloy NI-PD9001 (NiCu31). Annealed, seamless tube D ? 75 mm, a ? 3 mm
- BS-EN-4379 - Aerospace series. Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb).Solution treated, forging De 200 mm
- BS-EN-4500-001 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-002 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-003 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-003-TC - Tracked Changes. Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-004 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-005 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4500-006 - Aerospace series. Metallic materials. Rules for drafting and presentation of material standards
- BS-EN-4526 - Aerospace series. Metallic materials. Test methods. Sharp edge-notch tensile testing for sheet and strip
- BS-EN-4566 - Aerospace series. Heat resisting alloy CO-PH4101 (CoCr20W15N1) -Vacuum melted. Solution treated. Forgings. De < 100 mm
- BS-EN-4615 - Aerospace series. Magnesium alloy MG-C18002. T4. Sand casting
- BS-EN-4616 - Aerospace series. Magnesium alloy MG-C18002. T4. Chill casting
- BS-EN-4842 - Aerospace series. Steel X5CrNiCu15-5 (1.4545). Consumable electrode remelted (ESR or VAR). Solution treated and precipitation treated (H1025). Bars for machining. a or D 250 mm. 1 070 MPa Rm 1 200 MPa. Premium quality (pq)
- BS-EN-4842-TC - Tracked Changes. Aerospace series. Steel X5CrNiCu15-5 (1.4545). Consumable electrode remelted (ESR or VAR). Solution treated and precipitation treated (H1025). Bars for machining. a or D 250 mm. 1 070 MPa Rm 1 200 MPa. Premium quality (pq)
- BS-EN-6018 - Aerospace series. Test methods for metallic materials. Determination of density according to displacement method
- BS-M-93 - Protection of magnesium-rich alloys against corrosion. Specification
Other SDOs:
- EN-2032-001 - Aerospace series - Metallic materials - Part 001: Conventional designation
- EN-2043 - Aerospace series - Metallic materials - General requirements for semi-finished product qualification (excluding forgings and castings)
- EN-2306 - Aerospace series - Heat resisting - Nickel base alloy Ni-Cr20Co3Fe3 - Annealed - Bars
- EN-2402 - Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ? 10 mm
- EN-2732 - Magnesium Alloy mg-C46001-T6, Chill Casting
- EN-2959 - Aerospace series - Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked - Bar for forged fasteners - 3 mm
D 30 mm - EN-3668 - Aerospace Series - Heat Resisting Alloy NI-Ph2301 (Nicr21Fe18Mo9) - Non Heat Treated -
- EN-3844-1 - Aerospace series - Flammability of non metallic materials - Part 1: Small burner test, vertical - Determination of the vertical flame propagation
- EN-3844-2 - Aerospace series - Flammability of non metallic materials - Part 2: Small burner test, horizontal - Determination of the horizontal flame propagation
- EN-3844-3 - Aerospace series - Flammability of non metallic materials - Part 3: Small burner test, 45 Degrees - Determination of the resistance of material to flame and glow propagation and to flame penetration
- EN-3873 - Aerospace series - Test methods for metallic materials - Determination of fatigue crack growth rates using Corner-Cracked (CC) test pieces
- EN-3875 - Aerospace series - Metallic materials, Filler metal for brazing - Technical specification
- EN-3953 - Aerospace Series, Silver Base Alloy AG-B12401 (Agcu40Zn5NI), Filler Metal for Brazing,
- EN-4050-1 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 1: General requirements
- EN-4050-2 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 2: Performance of test
- EN-4050-3 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks
- EN-4050-4 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 4: Acceptance criteria
- EN-4268 - Aerospace series - Metallic materials - Heat treatment facilities - General requirements
- EN-4372 - Aerospace Series - Heat Resisting Nickel Alloy With Copper NI - Pd9001 Nicu31) - Wire
- EN-4379 - Aerospace Series - Heat Resisting Alloy NI-Ph3601 (Nicr22Mo9Nb) - Solution Treated, Fo
- EN-4500-001 - Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 001: General rules
- EN-4500-003 - Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 003: Specific rules for heat resisting alloys
- EN-4526 - Aerospace series - Metallic materials - Test methods - Sharp edge-notch tensile testing for sheet and strip
- EN-4842 - Aerospace series - X5CrNiCu15-5 (1.4545) - Consumable electrode remelted (ESR or VAR) - Solution treated and precipitation treated (H1025) - Bar for machining - a or D
250 mm - 1070 MPa R<(Index)m> 1200 MPa - Premium quality (pq) - EN-6018 - Aerospace series - Test methods for metallic materials - Determination of density according to displacement method
- EN-6072 - Aerospace series - Metallic materials - Test methods - Constant amplitude fatigue testing
- SS-EN-14902 - Ambient air quality - Standard method for the measurement of Pb, Cd, As and Ni in the PM10 fraction of suspended particulate matter
- SS-EN-2002-001 - Aerospace series - Metallic materials - Test methods - Part 1: Tensile testing at ambient temperature
- SS-EN-2002-002 - Aerospace series - Metallic materials - Test methods - Part 2: Tensile testing at elevated temperature
- SS-EN-2002-16 - Aerospace series - Metallic materials - Test methods - Part 16: Non-destructive testing - Penetrant testing
- SS-EN-2002-21 - Aerospace series - Metallic materials - Test methods - Part 21: Radiographic testing of castings
- SS-EN-2032-001 - Aerospace series - Metallic materials - Part 001: Conventional designation
- SS-EN-2032-1 - Aerospace series - Metallic materials - Part 1: Conventional designation
- SS-EN-2043 - Aerospace series - Metallic materials - General requirements for semi-finished product qualification (excluding forgings and castings)
- SS-EN-2078 - Aerospace series - Metallic materials - Manufacturing schedule, inspection schedule, inspection and test report - Definition, general principles, preparation and approval
- SS-EN-2302 - Aerospace series - Heat-resisting nickel base alloy NiCr20Co3Fe3 - Rm ≥ 650 MPa - Sheets and strips, cold rolled - 0,25 mm < a ≤ 3 mm
- SS-EN-2306 - Aerospace series - Heat resisting - Nickel base alloy Ni-Cr20Co3Fe3 - Annealed - Bars
- SS-EN-23878 - Hardmetals - Vickers hardness test (ISO 3878:1983)
- SS-EN-2400 - Aerospace series - Heat resisting nickel base alloy NI-P96-HT - Cold drawn and precipitation treated - Wire - D ≤ 10 mm
- SS-EN-2402 - Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm
- SS-EN-2731 - Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting
- SS-EN-2732 - Aerospace series - Magnesium alloy MG-C46001-T6 - Chill casting
- SS-EN-2959 - Aerospace series - Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked - Bar for forged fasteners - 3 mm = D = 30 mm
- SS-EN-2960 - Aerospace series - Heat resisting nickel base alloy (NI-P101HT) - Cold worked and solution treated - Bars for machining for fasteners - 3 mm = D = 50 mm
- SS-EN-3018 - Aerospace series - Heat resisting alloy NI-PH2801 (NiCr16Fe7Ti3Nb1Al1) - Consumable electrode remelted - Cold drawn wire for the manufacture of thread inserts - D = 3 mm
- SS-EN-3668 - Aerospace series - Heat resisting alloy NI-PH2301 (NiCr21Fe18Mo9) - Non heat treated - Forging stock - a or D ≤ 250 mm
- SS-EN-3844-1 - Aerospace series - Flammability of non-metallic materials - Part 1: Small burner test, vertical - Determination of the vertical flame propagation
- SS-EN-3844-2 - Aerospace series - Flammability of non-metallic materials - Part 2: Small burner test, horizontal - Determination of the horizontal flame propagation
- SS-EN-3844-3 - Aerospace series - Flammability of non-metallic materials - Part 3: Small burner test, 45° - Determination of the resistance of material to flame and glow propagation and to flame penetration
- SS-EN-3873 - Aerospace series - Test methods for metallic materials - Determination of fatigue crack growth rates using Corner-Cracked (CC) test pieces
- SS-EN-3875 - Aerospace series - Metallic materials, Filler metal for brazing - Technical specification
- SS-EN-3882 - Aerospace series - Heat resisting alloy NI-WH1801 (NiCr20Co18Ti3Al2) - Filler metal for welding
- SS-EN-3883 - Aerospace series - Heat resisting alloy NI-WH2301 (NiCr22Fe19Mo9Co2) - Filler metal for welding
- SS-EN-3884 - Aerospace series - Heat resisting alloy NI-WH2601 (NiCr19Nb5Mo3Ti) - Filler metal for welding
- SS-EN-3885 - Aerospace series - Heat resisting alloy NI-WH3601 (NiCr22Mo9Nb4) - Filler metal for welding
- SS-EN-3886 - Aerospace series - Heat resisting alloy NI-WH1303 (NiCo20Cr20Mo5Ti2Al) - Filler metal for welding
- SS-EN-3887 - Aerospace series - Heat resisting alloy Co-WH4101 (CoCr20W15Ni) - Filler metal for welding
- SS-EN-3888 - Aerospace series - Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) - Filler metal for welding
- SS-EN-3894 - Aerospace series - Heat resisting alloy NI-WD3201 (NiMo25Fe6Cr5) - Filler metal for welding
- SS-EN-3895 - Aerospace series - Heat resisting alloy Ni-WH3901 (NiCr16Mo15) - Filler metal for welding
- SS-EN-3927 - Aerospace series - Nickel base alloy NI-B40001 (NiSi5B3) - Filler metal for brazing - Powder or paste
- SS-EN-3930 - Aerospace series - Nickel base alloy NI-B31001 (NiCr19Si10) - Filler metal for brazing - Powder or paste
- SS-EN-3933 - Aerospace series - Nickel base alloy NI-B13001 (NiP11) - Filler metal for brazing - Powder or paste
- SS-EN-3936 - Aerospace series - Nickel base alloy NI-B21001 (NiCr15B4) - Filler metal for brazing - Powder or paste
- SS-EN-3937 - Aerospace series - Nickel base alloy NI-B44101 (NiW12Cr10Si4Fe3B3) - Filler metal for brazing - Powder or paste
- SS-EN-3952 - Aerospace series - Silver base alloy AG-B10001 (AgCu28) - Filler metal for brazing - Wire
- SS-EN-3953 - Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Wire
- SS-EN-3954 - Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Powder or paste
- SS-EN-3955 - Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Rolled foil
- SS-EN-3956 - Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Wire
- SS-EN-3957 - Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Powder or paste
- SS-EN-3958 - Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Rolled foil
- SS-EN-3959 - Aerospace series - Cobalt base alloy CO-B41601 (CoCr19Ni17Si8W4) - Filler metal for brazing - Powder or paste
- SS-EN-3960 - Aerospace series - Gold base alloy AU-B40001 (AuNi18) - Filler metal for brazing - Powder or paste
- SS-EN-3961 - Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Rolled foil
- SS-EN-3962 - Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire
- SS-EN-3963 - Aerospace series - Copper CU-BU9001 - Filler metal for brazing - Rolled foil
- SS-EN-3964 - Aerospace series - Copper CU-BU9001 - Filler metal for brazing - Wire
- SS-EN-4000 - Aerospace series - Metallic materials - Rules for the drafting and presentation of dimensional standards for metallic semi-finished products
- SS-EN-4050-1 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 1: General requirements
- SS-EN-4050-2 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 2: Performance of test
- SS-EN-4050-3 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks
- SS-EN-4050-4 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 4: Acceptance criteria
- SS-EN-4060 - Aerospace series - Filler rods and filler wires for welding in heat resisting alloys - Diameter 0,5 mm less than or equal to D less than or equal to 5,0 mm - Dimensions
- SS-EN-4104 - Aerospace series - Nickel base alloy NI-B40002 - Filler metal for brazing - Powder or paste
- SS-EN-4250 - Aerospace series - Nickel base alloys NI-B41001 (NiCr19Si7B) - Filler metal for brazing - Amorphous foil
- SS-EN-4259 - Aerospace series - Metallic materials - Definition of general terms
- SS-EN-4260 - Aerospace series - Metallic materials - Rules for drafting and presentation of technical specifications
- SS-EN-4261 - Aerospace series - Metallic materials - Rules for drafting and presentation of test method standards
- SS-EN-4268 - Aerospace series - Metallic materials - Heat treatment facilities - General requirements
- SS-EN-4325 - Aerospace series - Heat resisting alloy NI-WH1302 (NiCr20Co13Mo4Ti3Al) - Filler metal for welding - Wire and rod
- SS-EN-4326 - Aerospace series - Heat resisting alloy CO-WH4102 (CoCr28W20Ni5V1) - Filler metal for welding - Wire and rod
- SS-EN-4327 - Aerospace series - Heat resisting alloy CO-WH1401 (CoCr26Ni11W8) - Filler metal for welding - Wire and rod
- SS-EN-4329 - Aerospace series - Heat resisting alloy NI-WH0001 (NiCr20) - Filler metal for welding - Wire and rod
- SS-EN-4337 - Aerospace series - Heat resisting alloy NI-WH8901 (NiCr16Ti3Mn2) - Filler metal for welding - Wire and rod
- SS-EN-4338 - Aerospace series - Heat resisting alloy NI-WH3902 (NiCr25Mo10C) - Filler metal for welding - Wire and rod
- SS-EN-4339 - Aerospace series - Heat resisting alloy CO-WH4001 (CoCr29W9) - Filler metal for welding - Wire and rod
- SS-EN-4340 - Aerospace series - Magnesium alloy MG-W68001 - Filler metal for welding - Wire and rod
- SS-EN-4372 - Aerospace series - Heat resisting nickel alloy with copper NI-PD9001 (NiCu31) - Wire for solid rivets - D ≤ 10 mm
- SS-EN-4373 - Aerospace series - Heat resisting alloy NI-PD9001 (NiCu31) - Annealed, seamless tube D ≤ 75 mm, a ≤ 3 mm
- SS-EN-4379 - Aerospace series - Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) - Solution treated, forging De ≤ 200 mm
- SS-EN-4500-001 - Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 001: General rules
- SS-EN-4500-003 - Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 003: Specific rules for heat resisting alloys
- SS-EN-4526 - Aerospace series - Metallic materials - Test methods - Sharp edge-notch tensile testing for sheet and strip
- SS-EN-4566 - Aerospace series - Heat resisting alloy CO-PH4101 (CoCr20W15N1) -Vacuum melted - Solution treated - Forgings - De = 100 mm
- SS-EN-4615 - Aerospace series - Magnesium alloy MG-C18002 - T4 - Sand casting
- SS-EN-4616 - Aerospace series - Magnesium alloy MG-C18002 - T4 - Chill casting
- SS-EN-4842 - Aerospace series - Steel X5CrNiCu15-5 (1.4545) - Consumable electrode remelted (ESR or VAR) - Solution treated and precipitation treated (H1025) - Bars for machining - a or D = 250 mm - 1 070 MPa = Rm = 1 200 MPa - Premium quality (pq)
- SS-EN-6018 - Aerospace series - Test methods for metallic materials - Determination of density according to displacement method