Document Center List of Standards on Control Components Including Valves
ICS Code 23.100.50
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
BSI:
- BS-4151 - Method of evaluating pneumatic valve positioners with input signal of 3 to 15 lbf/in2 (gauge)
- BS-5944-4 - Measurement of airborne noise from hydraulic fluid power systems and components
- BS-6494-5 - Hydraulic fluid power valve mounting surfaces. Specification for compensated flow-control valves
- BS-6494-6 - Hydraulic fluid power valve mounting surfaces. Specification for pressure-control valves (excluding pressure-relief valves), sequence valves, unloading valves, throttle valves and check valves
- BS-7296-1 - Cavities for hydraulic fluid power cartridge valves. Specification for two-port slip-in valves
- BS-ISO-10094-1-TC - Tracked Changes. Pneumatic fluid power. Electro-pneumatic pressure control valves
- BS-ISO-10770-1 - Hydraulic fluid power. Electrically modulated hydraulic control valves
- BS-ISO-10770-2 - Hydraulic fluid power. Electrically modulated hydraulic control valves
- BS-ISO-10770-3 - Hydraulic fluid power. Electrically modulated hydraulic control valves
- BS-ISO-10770-3-TC - Tracked Changes. Hydraulic fluid power. Electrically modulated hydraulic control valves
- BS-ISO-12238 - Pneumatic fluid power. Directional control valves. Measurement of shifting time
- BS-ISO-15218 - Pneumatic fluid power. 3/2 solenoid valves. Mounting interface surfaces
- BS-ISO-15407-1 - Pneumatic fluid power. Five-port directional control valves, sizes 18 mm and 26 mm
- BS-ISO-15524 - Pneumatic fluid power. Cylinders. Single-rod short-stroke cylinders, 1000 kPa (10 bar) series, bores from 20 mm to 100 mm
- BS-ISO-16873 - Hydraulic fluid power. Pressure switches. Mounting surfaces
- BS-ISO-16874 - Hydraulic fluid power. Identification of manifold assemblies and their components
- BS-ISO-17082 - Pneumatic fluid power. Valves. Data to be included in supplier literature
- BS-ISO-20401 - Pneumatic fluid power systems. Directional control valves. Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors
- BS-ISO-4401 - Hydraulic fluid power. Four-port directional control valves. Mounting surfaces
- BS-ISO-4411 - Hydraulic fluid power. Valves. Determination of differential pressure/flow rate characteristics
- BS-ISO-5599-1 - Pneumatic fluid power. Five-port directional control valves
- BS-ISO-5599-2 - Pneumatic fluid power. Five-port directional control valves
- BS-ISO-5781 - Hydraulic fluid power. Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves. Mounting surfaces
- BS-ISO-5783 - Hydraulic fluid power. Code for identification of valve mounting surfaces and cartridge valve cavities
- BS-ISO-6263 - Hydraulic fluid power. Compensated flow-control valves. Mounting surfaces
- BS-ISO-6953-1 - Pneumatic fluid power. Compressed air pressure regulators and filter-regulators
- BS-ISO-6953-1-TC - Tracked Changes. Pneumatic fluid power. Compressed air pressure regulators and filter-regulators
- BS-ISO-6953-2 - Pneumatic fluid power. Compressed air pressure regulators and filter-regulators
- BS-ISO-6953-2-TC - Tracked Changes. Pneumatic fluid power. Compressed air pressure regulators and filter-regulators
- BS-ISO-6953-3 - Pneumatic fluid power. Compressed air pressure regulators and filter-regulators
- BS-ISO-7368 - Hydraulic fluid power. Two-port slip-in cartridge valves. Cavities
- BS-ISO-7789 - Hydraulic fluid power. Two-, three- and four-port screw-in cartridge valves. Cavities
- BS-ISO-7790 - Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10. Clamping dimensions
- PAS-4443 - Assessment criteria: Ancillary valves, devices and components used in hydrogen gas installations. Specification
- PD-ISO-17209 - Hydraulic fluid power. Two-, three-and four-port screw-in cartridge valves. Cavities with ISO 725 (UN and UNF) threads
IEC:
ISO:
- ISO-10041-1 - Pneumatic fluid power - Electro-pneumatic continuous flow control valves - Part 1: Main characteristics to include in the suppliers literature
- ISO-10041-2 - Pneumatic fluid power - Electro-pneumatic continuous flow control valves - Part 2: Test methods to determine main characteristics to include in the suppliers literature
- ISO-10094-1 - Pneumatic fluid power - Electro-pneumatic pressure control valves - Part 1: Main characteristics to include in the suppliers literature
- ISO-10094-2 - Pneumatic fluid power - Electro-pneumatic pressure control valves - Part 2: Test methods to determine main characteristics to include in the suppliers literature
- ISO-10372 - Hydraulic fluid power - Four- and five-port servovalves - Mounting surfaces
- ISO-10770-1 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 1: Test methods for four-port directional flow-control valves
- ISO-10770-2 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 2: Test methods for three-port directional flow-control valves
- ISO-10770-3 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 3: Test methods for pressure control valves
- ISO-11727 - Pneumatic fluid power -- Identification of ports and control mechanisms of control valves and other components
- ISO-12238 - Pneumatic fluid power - Directional control valves - Measurement of shifting time
- ISO-15218 - Pneumatic fluid power - 3/2 solenoid valves - Mounting interface surfaces
- ISO-15407-1 - Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector
- ISO-15407-2 - Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2: Mounting interface surfaces with optional electrical connector
- ISO-15524 - Pneumatic fluid power - Cylinders - Single-rod short-stroke cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm
- ISO-16873 - Hydraulic fluid power - Pressure switches - Mounting surfaces
- ISO-16873-1 - Hydraulic fluid power - Pressure switches - Mounting surfacesAmendment 1
- ISO-16874 - Hydraulic fluid power - Identification of manifold assemblies and their components
- ISO-17082 - Pneumatic fluid power - Valves - Data to be included in supplier literature
- ISO-17209 - Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities with ISO 725 (UN and UNF) threads
- ISO-20401 - Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors
- ISO-4401 - Hydraulic fluid power - Four-port directional control valves - Mounting surfaces
- ISO-4411 - Hydraulic fluid power - Valves - Determination of differential pressure/flow rate characteristics
- ISO-5599-1 - Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector
- ISO-5599-2 - Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector
- ISO-5599-2-1 - Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector - Amendment 1
- ISO-5599-3 - Pneumatic fluid power - Five-port directional control valves - Part 3: Code system for communication of valve functions
- ISO-5781 - Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces
- ISO-5783 - Hydraulic fluid power - Code for identification of valve mounting surfaces and cartridge valve cavities
- ISO-6263 - Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces
- ISO-6264 - Hydraulic fluid power - Pressure-relief valves - Mounting surfaces
- ISO-6403 - Hydraulic fluid power - Valves controlling flow and pressure - Test methods
- ISO-6953-1 - Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to include in suppliers literature and product-marking requirements
- ISO-6953-2 - Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 2: Test methods to determine the main characteristics to include in supplier.s literature
- ISO-6953-3 - Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 3: Alternative test methods for measuring the flow-rate characteristics of pressure regulators
- ISO-7368 - Hydraulic fluid power - Two-port slip-in cartridge valves - Cavities
- ISO-7789 - Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities
- ISO-7790 - Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03, 05, 07, 08 and 10 - Clamping dimensions
- ISO-9461 - Hydraulic fluid power -- Identification of valve ports, subplates, control devices and solenoids
Other SDOs:
- DIN-ISO-12238 - Pneumatic Fluid Power - Directional Control Valves - Measurement of Shifting Time
- DIN-ISO-5599-1 - Part 1: Mounting Interface Surfaces Without Electrical Connector, Pneumatic Fluid Powe
- JIS-B-8347 - Hydraulic fluid power -- Identification of manifold assemblies and their components
- JIS-B-8372-1 - Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 1: Main characteristics to be included in literature from suppliers and product-making requirements
- JIS-B-8372-2 - Pneumatic fluid power -- Compressed air pressure regulators and filter-regulators -- Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
- SS-EN-14492-1 - Cranes - Power driven winches and hoists - Part 1: Power driven winches
- SS-ISO-10372 - Hydraulic fluid power - Four- and five-port servovalves - Mounting surfaces
- SS-ISO-10770-1 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 1: Test methods for four-port directional flow-control valves (ISO 10770-1:2009, IDT)
- SS-ISO-10770-2 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 2: Test methods for three-port directional flow control valves (ISO 10770-2:2012, IDT)
- SS-ISO-10770-3 - Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 3: Test methods for pressure control valves (ISO 10770-3:2007, IDT)
- SS-ISO-10791-3 - Test conditions for machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z axis)
- SS-ISO-11727 - Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components
- SS-ISO-12238 - Pneumatic fluid power - Directional control valves - Measurement of shifting time (ISO 12238:2023, IDT)
- SS-ISO-15218 - Pneumatic fluid power - 3/2 solenoid valves - Mounting interface surfaces
- SS-ISO-15407-1 - Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector
- SS-ISO-15407-2 - Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2: Mounting interface surfaces with optional electrical connector
- SS-ISO-16873 - Hydraulic fluid power - Pressures switches - Mounting surfaces
- SS-ISO-16874 - Hydraulic fluid power - Identification of manifold assemblies and their components (ISO 16874:2004, IDT)
- SS-ISO-17082 - Pneumatic fluid power - Valves - Data to be included in supplier literature (ISO 17082:2004, IDT)
- SS-ISO-20401 - Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm (ISO 20401:2005, IDT)
- SS-ISO-4401 - Hydraulic fluid power - Four-port directional control valves - Mounting surfaces (ISO 4401:2005, IDT)
- SS-ISO-4411 - Hydraulic fluid power - Valves - Determination of differential pressure/flow rate characteristics (ISO 4411:2019, IDT)
- SS-ISO-5599-1 - Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector
- SS-ISO-5599-2 - Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector
- SS-ISO-5599-2-AM1 - Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector (ISO 5599-2:2002/Amd 1:2004, IDT)
- SS-ISO-5781 - Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces (ISO 5781:2000, IDT)
- SS-ISO-5783 - Hydraulic fluid power - Code for identification of valve mounting surfaces and cartridge valve cavities (ISO 5783:2019, IDT)
- SS-ISO-6263 - Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces (ISO 6263:1997, IDT)
- SS-ISO-6264 - Hydraulic fluid power - Pressure-relief valves - Mounting surfaces
- SS-ISO-6403 - Hydraulic fluid power - Valves controlling flow and pressure - Test methods (ISO 6403:1988, IDT)
- SS-ISO-6953-1 - Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements (ISO 6953-1:2000/Cor 1:2006, IDT)
- SS-ISO-6953-2 - Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
- SS-ISO-7789 - Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities (ISO 7789:2007, IDT)
- SS-ISO-7790 - Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions
- SS-ISO-9461 - Hydraulic fluid power - Identification of valve ports, subplates, control devices and solenoids