Document Center List of Standards on Pipelines And Its Parts For External Sewage Systems
ICS Code 23.040.05
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C118 - Standard Specification for Concrete Pipe for Irrigation or Drainage
- ASTM-C118M - Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric)
- ASTM-F1866 - Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
- ASTM-F628 - Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021)
BSI:
- BS-EN-12200-1-TC - Tracked Changes. Plastics rainwater piping systems for above ground external use. Unplasticized poly(vinyl chloride) (PVC-U)
- BS-EN-12201-1-TC - Tracked Changes. Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12889-TC - Tracked Changes. Trenchless construction and testing of drains and sewers
- BS-EN-1453-1 - Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U)
- BS-EN-476-TC - Tracked Changes. General requirements for components used in drains and sewers
- BS-EN-877-TC - Tracked Changes. Cast iron pipe systems and their components for the evacuation of water from works. characteristics and test methods
- DD-ENV-1453-2 - Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U)
- PD-CEN-12200-2 - Plastics rainwater piping systems for above ground external use. Unplasticized poly(vinyl chloride) (PVC-U)
- PD-CEN-12200-2-TC - Tracked Changes. Plastics rainwater piping systems for above ground external use. Unplasticized poly(vinyl chloride) (PVC-U)
- PD-CEN-13598-3-TC - Tracked Changes. Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
- PD-CEN-14632-TC - Tracked Changes. Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the assessment of conformity
- PD-CEN-17179 - Thermoplastics piping and ducting systems. Rainwater infiltration and storage attenuation systems. Practices for underground installation
Other SDOs:
- EN-1453-1 - Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
- SIS-CEN/TS-1046 - Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
- SIS-CEN/TS-13598-3 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity
- SIS-CEN/TS-1401-2 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
- SIS-CEN/TS-14632 - Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
- SIS-CEN/TS-1852-2 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
- SS-EN-1053 - Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methodfor watertightness
- SS-EN-1054 - Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints
- SS-EN-1055 - Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
- SS-EN-1123-1 - Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
- SS-EN-1123-1-AM1 - Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
- SS-EN-1123-2 - Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions
- SS-EN-1124-1 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
- SS-EN-1124-1-AM1 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
- SS-EN-1124-2 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 2: System S, forms and dimensions
- SS-EN-1124-3 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 3: System X - Dimensions
- SS-EN-1124-4 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems - Part 4: Components for vacuum drainage systems and for drainage systems on ships
- SS-EN-12200-1 - Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
- SS-EN-12201-1 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
- SS-EN-12201-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- SS-EN-12201-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
- SS-EN-12201-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
- SS-EN-12666-1 - Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
- SS-EN-12763 - Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery
- SS-EN-12889 - Trenchless construction and testing of drains and sewers
- SS-EN-13476-3 - Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B
- SS-EN-13598-1 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings and shallow chambers
- SS-EN-13598-2 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
- SS-EN-1401-1 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems
- SS-EN-1453-1 - Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
- SS-EN-14636-1 - Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
- SS-EN-14741 - Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure
- SS-EN-14758-1 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
- SS-EN-15030 - Chemicals used for treatment of water intended for human consumption - Silver salts for intermittent use
- SS-EN-16506 - Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
- SS-EN-1852-1 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
- SS-EN-1916 - Concrete pipes and fittings, unreinforced, steel fibre and reinforced
- SS-EN-295-1 - Vitrified clay pipe systems for drains and sewers - Part 1: Requirements for pipes, fittings and joints
- SS-EN-295-2 - Vitrified clay pipe systems for drains and sewers - Part 2: Evaluation of conformity and sampling
- SS-EN-295-4 - Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors, connectors and flexible couplings
- SS-EN-295-5 - Vitrified clay pipe systems for drains and sewers - Part 5: Requirements for perforated pipes and fittings
- SS-EN-295-6 - Vitrified clay pipes systems for drain and sewers - Part 6: Requirements for components of manholes and inspection chambers
- SS-EN-295-7 - Vitrified clay pipe systems for drains and sewers - Part 7: Requirements for pipes and joints for pipe jacking
- SS-EN-476 - General requirements for components used in drains and sewers
- SS-EN-512 - Fibre-cement products - Pressure pipes and joints
- SS-EN-512-AM1 - Fibre-cement products - Pressure pipes and joints
- SS-EN-588-1 - Fibre-cement pipes for sewers and drains - Part 1: Pipes, joints and fittings for gravity systems
- SS-EN-598 - Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
- SS-EN-681-1 - Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
- SS-EN-681-1-AM1 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
- SS-EN-681-1-AM2 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
- SS-EN-681-1-AM3 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
- SS-EN-681-2 - Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
- SS-EN-681-2-AM1 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
- SS-EN-681-2-AM2 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
- SS-EN-681-3 - Elastomeric seals - Materials requirements for pipe joints seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber
- SS-EN-681-3-AM1 - Elastomeric seals - Material requirements for joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber
- SS-EN-681-3-AM2 - Elastomeric seals - Materials requirements for pipe joints seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber
- SS-EN-681-4 - Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
- SS-EN-681-4-AM1 - Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
- SS-EN-681-4-AM2 - Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
- SS-EN-752 - Drain and sewer systems outside buildings - Sewer system management
- SS-EN-877 - Cast iron pipe systems and their components for the evacuation of water from works - characteristics and test methods
- SS-EN-877-AM1 - Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance
- SS-EN-ISO-13254 - Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254:2010)
- SS-EN-ISO-13255 - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for airtightness of joints (ISO 13255:2010)
- SS-EN-ISO-13257 - Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2018)
- SS-EN-ISO-9100-14 - Glass containers - Vacuum lug finishes - Part 14: 110 regular (ISO 9100-14:2005)
- SS-ENV-1452-7 - Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity