Document Center List of Standards on Heat. Calorimetry
ICS Code 17.200.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1043 - Standard Practice for Guarded-Hot-Plate Design Using Circular Line-Heat Sources
- ASTM-C1044 - Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode
- ASTM-C1045 - Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
- ASTM-C1114 - Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
- ASTM-C1130 - Standard Practice for Calibration of Thin Heat Flux Transducers
- ASTM-C1132 - Standard Practice for Calibration of the Heat Flow Meter Apparatus (Withdrawn 2002)
- ASTM-C1171 - Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories
- ASTM-C1371 - Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
- ASTM-C1702 - Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry
- ASTM-C177 - Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ASTM-C1784 - Standard Test Method for Using a Heat Flow Meter Apparatus for Measuring Thermal Storage Properties of Phase Change Materials and Products
- ASTM-C745 - Standard Test Method for Heat Flux Through Evacuated Insulations Using a Guarded Flat Plate Boiloff Calorimeter (Withdrawn 2008)
- ASTM-D1826 - Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter
- ASTM-D2717 - Standard Test Method for Thermal Conductivity of Liquids (Withdrawn 2018)
- ASTM-D2766 - Standard Test Method for Specific Heat of Liquids and Solids (Withdrawn 2018)
- ASTM-D6011 - Standard Test Method for Determining the Performance of a Sonic Anemometer/Thermometer
- ASTM-D7314 - Standard Practice for Determination of the Heating Value of Gaseous Fuels using Calorimetry and On-line/At-line Sampling
- ASTM-E1142 - Standard Terminology Relating to Thermophysical Properties
- ASTM-E1225 - Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique
- ASTM-E1269 - Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
- ASTM-E1354 - Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
- ASTM-E1356 - Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry
- ASTM-E144 - Standard Practice for Safe Use of Oxygen Combustion Vessels
- ASTM-E1461 - Standard Test Method for Thermal Diffusivity by the Flash Method
- ASTM-E1530 - Standard Test Method for Evaluating the Resistance to Thermal Transmission by the Guarded Heat Flow Meter Technique
- ASTM-E1782 - Standard Test Method for Determining Vapor Pressure by Thermal Analysis
- ASTM-E1824 - Standard Test Method for Assignment of a Glass Transition Temperature Using Thermomechanical Analysis: Tension Method
- ASTM-E1862 - Standard Practice for Measuring and Compensating for Reflected Temperature Using Infrared Imaging Radiometers
- ASTM-E1897 - Standard Practice for Measuring and Compensating for Transmittance of an Attenuating Medium Using Infrared Imaging Radiometers
- ASTM-E1933 - Standard Practice for Measuring and Compensating for Emissivity Using Infrared Imaging Radiometers
- ASTM-E1952 - Standard Test Method for Thermal Conductivity and Thermal Diffusivity by Modulated Temperature Differential Scanning Calorimetry
- ASTM-E1970 - Standard Practice for Statistical Treatment of Thermoanalytical Data
- ASTM-E1981 - Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
- ASTM-E2009 - Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry
- ASTM-E2038 - Standard Test Method for Temperature Calibration of Dielectric Analyzers (Withdrawn 2009)
- ASTM-E2041 - Standard Test Method for Estimating Kinetic Parameters by Differential Scanning Calorimeter Using the Borchardt and Daniels Method
- ASTM-E2069 - Standard Test Method for Temperature Calibration on Cooling of Differential Scanning Calorimeters
- ASTM-E2070 - Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods
- ASTM-E2253 - Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters
- ASTM-E2584 - Standard Practice for Thermal Conductivity of Materials Using a Thermal Capacitance (Slug) Calorimeter
- ASTM-E2585 - Standard Practice for Thermal Diffusivity by the Flash Method
- ASTM-E2602 - Standard Test Methods for Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry
- ASTM-E2603 - Standard Practice for Calibration of Fixed-Cell Differential Scanning Calorimeters
- ASTM-E2683 - Standard Test Method for Measuring Heat Flux Using Flush-Mounted Insert Temperature-Gradient Gages
- ASTM-E2684 - Standard Test Method for Measuring Heat Flux Using Surface-Mounted One-Dimensional Flat Gages
- ASTM-E2716 - Standard Test Method for Determining Specific Heat Capacity by Modulated Temperature Differential Scanning Calorimetry
- ASTM-E2781 - Standard Practice for Evaluation of Methods for Determination of Kinetic Parameters by Calorimetry and Differential Scanning Calorimetry
- ASTM-E2890 - Standard Test Method for Kinetic Parameters for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger Method
- ASTM-E3057 - Standard Test Method for Measuring Heat Flux Using Directional Flame Thermometers with Advanced Data Analysis Techniques
- ASTM-E3174 - Standard Practice for Determination of Kinetic Reaction Model Using Differential Scanning Calorimetry
- ASTM-E341 - Standard Practice for Measuring Plasma Arc Gas Enthalpy by Energy Balance
- ASTM-E422 - Standard Test Method for Measuring Heat Flux Using a Water-Cooled Calorimeter
- ASTM-E457 - Standard Test Method for Measuring Heat-Transfer Rate Using a Thermal Capacitance (Slug) Calorimeter
- ASTM-E458 - Standard Test Method for Heat of Ablation
- ASTM-E459 - Standard Test Method for Measuring Heat Transfer Rate Using a Thin-Skin Calorimeter
- ASTM-E473 - Standard Terminology Relating to Thermal Analysis and Rheology
- ASTM-E476 - Standard Test Method for Thermal Instability of Confined Condensed Phase Systems (Confinement Test) (Withdrawn 2008)
- ASTM-E511 - Standard Test Method for Measuring Heat Flux Using a Copper-Constantan Circular Foil, Heat-Flux Transducer
- ASTM-E598 - Standard Test Method for Measuring Extreme Heat-Transfer Rates from High-Energy Environments Using a Transient, Null-Point Calorimeter
- ASTM-E637 - Standard Test Method for Calculation of Stagnation Enthalpy from Heat Transfer Theory and Experimental Measurements of Stagnation-Point Heat Transfer and Pressure
- ASTM-E638 - Test Method for Calibration of Heat Transfer Rate Calorimeters Using a Narrow-Angle Blackbody Radiation Facility (Withdrawn 2001)
- ASTM-E771 - Standard Test Method for Spontaneous Heating Tendency of Materials (Withdrawn 2001)
- ASTM-E793 - Standard Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry
- ASTM-E794 - Standard Test Method for Melting And Crystallization Temperatures By Thermal Analysis
- ASTM-E928 - Standard Test Method for Purity by Differential Scanning Calorimetry
- ASTM-E967 - Standard Test Method for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers
- ASTM-E968 - Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters (Withdrawn 2023)
- ASTM-F1720 - Standard Test Method for Measuring Thermal Insulation of Sleeping Bags Using a Heated Manikin
- ASTM-F2625 - Standard Test Method for Measurement of Enthalpy of Fusion, Percent Crystallinity, and Melting Point of Ultra-High Molecular Weight Polyethylene by Means of Differential Scanning Calorimetry
- ASTM-F3340 - Standard Test Method for Thermal Resistance of Camping Mattresses Using a Guarded Hot Plate Apparatus
BSI:
- BS-4791 - Specification for calorimeter bombs
- BS-5775-4 - Specification for quantities, units and symbols. Heat
- BS-7234-1 - Heat meters. Specification: general requirements
- BS-7234-2 - Heat meters. Specification for installation
- BS-7234-3 - Heat meters. Methods of test for pattern approval and initial verification
- BS-EN-12697-13 - Bituminous mixtures. Test methods
- BS-EN-12697-13-TC - Tracked Changes. Bituminous mixtures. Test methods
- BS-EN-1434-1 - Thermal energy meters
- BS-EN-1434-2 - Thermal energy meters
- BS-EN-1434-2-TC - Tracked Changes. Thermal energy meters
- BS-EN-1434-3 - Heat meters
- BS-EN-1434-3-TC - Tracked Changes. Heat meters
- BS-EN-1434-4 - Thermal energy meters
- BS-EN-1434-5 - Thermal energy meters
- BS-EN-1434-5-TC - Tracked Changes. Thermal energy meters
- BS-EN-1434-6 - Heat meters
- BS-ISO-11357-6 - Plastics. Differential scanning calorimetry (DSC)
- BS-ISO-11357-7 - Part 7: Determination of Crystallization Kinetics
- DD-246 - Recommendations for the use of the cone calorimeter
- PD-CEN-13582 - Installation of thermal energy meters. Guidelines for the selection, installation and operation of thermal energy meters
- PD-CR-13582 - Heat meter installation. Some guidelines for selecting, installation and operation of heat meters
Other SDOs:
- AS/NZS-3837 - Method of test for heat and smoke release rates for materials and products using an oxygen consumption calorimeter
- DIN-EN-13741 - Thermal Performance Acceptance Testing of Mechanical Draughtseries Wet Cooling Towers
- DIN-EN-1434-1 - Heat meters - Part 1: General requirements; German version EN 1434-1:2015
- DIN-EN-1434-2 - Heat meters - Part 2: Constructional requirements; German version EN 1434-2:2015
- DIN-EN-1434-4 - Heat meters - Part 4: Pattern approval tests; German version EN 1434-4:2015
- DIN-EN-1434-5 - Heat meters - Part 5: Initial verification tests; German version EN 1434-5:2015
- DIN-EN-1434-6 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance; German version EN 1434-6:2015
- EN-1434-1 - Heat meters - Part 1: General requirements
- EN-1434-2 - Heat meters - Part 2: Constructional requirements
- EN-1434-3 - Heat meters - Part 3: Data exchange and interfaces
- EN-1434-4 - Heat meters - Part 4: Pattern approval tests
- EN-1434-5 - Heat meters - Part 5: Initial verification tests
- EN-1434-6 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance
- JIS-C-1604 - Platinum resistance thermometers
- SIS-CEN/TR-15760 - Heat meters - Checklist documenting the relationship between the Directive 2004/22/EC (MID) and EN 1434:2007
- SMS-RAPPORT-56 - Värmemätare
- SS-EN-12697-13 - Bituminous mixtures - Test methods - Part 13: Temperature measurement
- SS-EN-13757-5 - Communication systems for meters - Part 5: Wireless M-Bus relaying
- SS-EN-13757-6 - Communication systems for meters - Part 6: Local Bus
- SS-EN-14122 - Foodstuffs - Determination of vitamin B1 by high performance liquid chromatography
- SS-EN-1434-1 - Thermal energy meters - Part 1: General requirements
- SS-EN-1434-1-AM1 - Heat meters - Part 1: General requirements
- SS-EN-1434-2 - Thermal energy meters - Part 2: Constructional requirements
- SS-EN-1434-2-AM1 - Heat meters - Part 2: Constructional requirements
- SS-EN-1434-3 - Heat meters - Part 3: Data exchange and interfaces
- SS-EN-1434-4 - Thermal energy meters - Part 4: Pattern approval tests
- SS-EN-1434-4-AM1 - Heat meters - Part 4: Pattern approval tests
- SS-EN-1434-5 - Thermal energy meters - Part 5: Initial verification tests
- SS-EN-1434-5-AM1 - Heat meters - Part 5: Initial verification tests
- SS-EN-1434-6 - Thermal energy meters - Part 6: Installation, commissioning, operational monitoring and maintenance
- SS-EN-1434-6-AM1 - Heat meters - Part 6: Installation, commissioning, operational monitoring and maintenance
- SS-EN-ISO-10548 - Carbon fibre - Determination of size content (ISO 10548:2002)
- UNE-EN-1434-4 - Heat meters - Part 4: Pattern approval tests