04.07: Building Seals and Sealants; Fire Standards; Dimension Stone
ASTM International (formerly the American Society for Testing and Materials) has published a complete collection of their standards for some time. This collection is divided into Sections and Volumes by subject classification for increased useability.
Return to Section Index
The following documents are a part of this series:
- ASTM-C1016 - Standard Test Method for Determination of Water Absorption of Sealant Backing
(Joint Filler) Material - ASTM-C1021 - Standard Practice for Laboratories Engaged in Testing of Building Sealants
- ASTM-C1083 - Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials
- ASTM-C1085 - Specification for Butyl Rubber Based Solvent-Release Sealants (Withdrawn 1997)
- ASTM-C1087 - Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
- ASTM-C1115 - Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
- ASTM-C1135 - Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
- ASTM-C1166 - Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories
- ASTM-C1173 - Standard Specification for Flexible Transition Couplings for Underground Piping Systems
- ASTM-C1183 - Standard Test Method for Extrusion Rate of Elastomeric Sealants
- ASTM-C1184 - Standard Specification for Structural Silicone Sealants
- ASTM-C119 - Standard Terminology Relating to Dimension Stone
- ASTM-C1193 - Standard Guide for Use of Joint Sealants
- ASTM-C120 - Standard Test Methods for Flexure Testing of Structural and Roofing Slate
- ASTM-C1201 - Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
- ASTM-C121 - Standard Test Method for Water Absorption of Slate
- ASTM-C1216 - Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants (Withdrawn 2022)
- ASTM-C1241 - Standard Test Method for Volume Shrinkage of Latex Sealants During Cure
- ASTM-C1242 - Standard Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems
- ASTM-C1246 - Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
- ASTM-C1247 - Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids
- ASTM-C1248 - Standard Test Method for Staining of Porous Substrate by Joint Sealants
- ASTM-C1249 - Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
- ASTM-C1253 - Standard Test Method for Determining the Outgassing Potential of Sealant Backing
- ASTM-C1257 - Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
- ASTM-C1265 - Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
- ASTM-C1266 - Standard Test Method for Flow Characteristics of Preformed Tape Sealants
- ASTM-C1277 - Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
- ASTM-C1281 - Standard Specification for Preformed Tape Sealants for Glazing Applications
- ASTM-C1294 - Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
- ASTM-C1299 - Standard Guide for Use in Selection of Liquid-Applied Sealants (Withdrawn 2012)
- ASTM-C1311 - Standard Specification for Solvent Release Sealants
- ASTM-C1330 - Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants
- ASTM-C1352 - Standard Test Method for Flexural Modulus of Elasticity of Dimension Stone
- ASTM-C1353 - Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
- ASTM-C1354 - Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone
- ASTM-C1367 - Standard Test Method for Dead Load Resistance of a Sealant in Elevated Temperatures
- ASTM-C1369 - Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
- ASTM-C1375 - Standard Guide for Substrates Used in Testing Building Seals and Sealants
- ASTM-C1382 - Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
- ASTM-C1392 - Standard Guide for Evaluating Failure of Structural Sealant Glazing
- ASTM-C1394 - Standard Guide for In-Situ Structural Silicone Glazing Evaluation
- ASTM-C1401 - Standard Guide for Structural Sealant Glazing
- ASTM-C1440 - Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems
- ASTM-C1442 - Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
- ASTM-C1460 - Standard Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground
- ASTM-C1461 - Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use
- ASTM-C1472 - Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
- ASTM-C1481 - Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- ASTM-C1487 - Standard Guide for Remedying Structural Silicone Glazing
- ASTM-C1496 - Standard Guide for Assessment and Maintenance of Exterior Dimension Stone Masonry Walls and Facades
- ASTM-C1501 - Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures
- ASTM-C1515 - Standard Guide for Cleaning of Exterior Dimension Stone, Vertical And Horizontal Surfaces, New or Existing
- ASTM-C1518 - Standard Specification for Precured Elastomeric Silicone Joint Sealants
- ASTM-C1519 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
- ASTM-C1520 - Standard Guide for Paintability of Latex Sealants
- ASTM-C1521 - Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
- ASTM-C1523 - Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants
- ASTM-C1526 - Standard Specification for Serpentine Dimension Stone
- ASTM-C1527 - Standard Specification for Travertine Dimension Stone
- ASTM-C1528 - Standard Guide for Selection of Dimension Stone
- ASTM-C1536 - Standard Test Method for Measuring the Yield for Aerosol Foam Sealants
- ASTM-C1540 - Standard Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
- ASTM-C1541 - Standard Specification for Shielded Transition Couplings Using Flexible Polyvinyl Chloride (PVC) Gaskets to Connect Dissimilar DWV Pipe and Fittings (Withdrawn 2022)
- ASTM-C1564 - Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
- ASTM-C1589 - Standard Practice for Outdoor Weathering of Construction Seals and Sealants
- ASTM-C1620 - Standard Specification for Aerosol Polyurethane and Aerosol Latex Foam Sealants
- ASTM-C1635 - Standard Test Method to Evaluate Adhesion/Cohesion Properties of a Sealant at Fixed Extension
- ASTM-C1642 - Standard Practice for Determining Air Leakage Rates of Aerosol Foam Sealants and Other Construction Joint Fill and Insulation Materials
- ASTM-C1643 - Standard Test Method to Measuring the Post Dispensing Volumetric Expansion of Aerosol Foam Sealants
- ASTM-C1681 - Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain
- ASTM-C170 - Standard Test Method for Compressive Strength of Dimension Stone
- ASTM-C1721 - Standard Guide for Petrographic Examination of Dimension Stone
- ASTM-C1722 - Standard Guide for Repair and Restoration of Dimension Stone
- ASTM-C1735 - Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation
- ASTM-C17353 - Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation
- ASTM-C1736 - Standard Practice for Non-Destructive Evaluation of Adhesion of Installed Weatherproofing Sealant Joints Using a Rolling Device (Withdrawn 2020)
- ASTM-C1737 - Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing
- ASTM-C1756 - Standard Guide for Comparing Seal or Sealant Behavior to Reference Photographs
- ASTM-C1799 - Standard Guide to Dimension Stone Test Specimen Sampling and Preparation
- ASTM-C1806 - Standard Test Method for Measuring the Flow Rate of Aerosol Foam Sealants
- ASTM-C1815 - Standard Practice for Periodically Measuring and Monitoring Sealant Dimensions to Stability Following a Period of Compression or Tension
- ASTM-C1850 - Standard Guide for Improved Laboratory Accelerated Tests to Predict the Weathering and for Use in Developing Protocols to Predict the Design Life of Building Sealant Systems
- ASTM-C1851 - Standard Practice for Determining the Extent of Cracking in a Sealant using the Difference between the Compressive and Tensile Modulus
- ASTM-C1852 - Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives
- ASTM-C217 - Standard Test Method for Weather Resistance of Slate
- ASTM-C241 - Standard Test Method for Abrasion Resistance of Stone Subjected to Foot Traffic
- ASTM-C406 - Standard Specification for Roofing Slate
- ASTM-C503 - Standard Specification for Marble Dimension Stone
- ASTM-C509 - Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing
Material - ASTM-C510 - Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
- ASTM-C542 - Standard Specification for Lock-Strip Gaskets
- ASTM-C543 - Specification for Slate Blackboards (Withdrawn 1987)
- ASTM-C564 - Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
- ASTM-C568 - Standard Specification for Limestone Dimension Stone
- ASTM-C570 - Standard Specification for Oil- and Resin-Base Caulking Compound for Building Construction (Withdrawn 2002)
- ASTM-C603 - Standard Test Method for Extrusion Rate and Application Life of Elastomeric Sealants
- ASTM-C615 - Standard Specification for Granite Dimension Stone
- ASTM-C616 - Standard Specification for Quartz-Based Dimension Stone
- ASTM-C629 - Standard Specification for Slate Dimension Stone
- ASTM-C639 - Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants
- ASTM-C661 - Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
- ASTM-C669 - Standard Specification for Glazing Compounds for Back Bedding and Face Glazing of Metal Sash (Withdrawn 2002)
- ASTM-C679 - Standard Test Method for Tack-Free Time of Elastomeric Sealants
- ASTM-C681 - Standard Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds
- ASTM-C711 - Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants
- ASTM-C712 - Standard Test Method for Bubbling of One-Part, Elastomeric, Solvent-Release Type Sealants
- ASTM-C713 - Standard Test Method for Slump of an Oil-Base Knife-Grade Channel Glazing Compound (Withdrawn 2002)
- ASTM-C716 - Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials
- ASTM-C717 - Standard Terminology of Building Seals and Sealants
- ASTM-C718 - Standard Test Method for Ultraviolet (UV)-Cold Box Exposure of One-Part, Elastomeric, Solvent-Release Type Sealants (Withdrawn 2002)
- ASTM-C719 - Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
- ASTM-C731 - Standard Test Method for Extrudability, After Package Aging, of Latex Sealants
- ASTM-C732 - Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
- ASTM-C733 - Standard Test Method for Volume Shrinkage of Latex Sealants (Withdrawn 2000)
- ASTM-C734 - Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering
- ASTM-C736 - Standard Test Method for Extension-Recovery and Adhesion of Latex Sealants
- ASTM-C741 - Standard Test Method for Accelerated Aging of Wood Sash Face Glazing Compound (Withdrawn 2002)
- ASTM-C742 - Standard Test Method for Degree of Set for Wood Sash Glazing Compound (Withdrawn 2002)
- ASTM-C765 - Standard Test Method for Low-Temperature Flexibility of Preformed Tape Sealants
- ASTM-C766 - Test Method for Adhesion After Impact of Preformed Tape Sealants (Withdrawn 1994)
- ASTM-C771 - Standard Test Method for Weight Loss After Heat Aging of Preformed Tape Sealants
- ASTM-C772 - Standard Test Method for Oil Migration or Plasticizer Bleed-Out of Preformed Tape Sealants
- ASTM-C782 - Standard Test Method for Softness of Preformed Tape Sealants
- ASTM-C790 - Guide for Use of Latex Sealants (Withdrawn 1992)
- ASTM-C792 - Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants
- ASTM-C793 - Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants
- ASTM-C794 - Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
- ASTM-C797 - Terminology for Use of Oil- and Resin-Based Putty and Glazing Compounds (Withdrawn 2002)
- ASTM-C804 - Practices for Use of Solvent-Release Type Sealants (Withdrawn 1992)
- ASTM-C834 - Standard Specification for Latex Sealants
- ASTM-C864 - Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers
- ASTM-C879 - Standard Test Methods for Release Papers Used with Preformed Tape Sealants
- ASTM-C880 - Standard Test Method for Flexural Strength of Dimension Stone
- ASTM-C883 - Standard Test Method for Effective Shrinkage of Epoxy-Resin Systems Used With Concrete (Withdrawn 1996)
- ASTM-C906 - Standard Test Method for T-Peel Strength of Hot Applied Sealants (Withdrawn 2006)
- ASTM-C907 - Standard Test Method for Tensile Adhesive Strength of Preformed Tape Sealants by Disk Method
- ASTM-C908 - Standard Test Method for Yield Strength of Preformed Tape Sealants
- ASTM-C910 - Standard Test Method for Bond and Cohesion of One-Part Elastomeric Solvent Release-Type Sealants
- ASTM-C919 - Standard Practice for Use of Sealants in Acoustical Applications
- ASTM-C920 - Standard Specification for Elastomeric Joint Sealants
- ASTM-C961 - Standard Test Method for Lap Shear Strength of Sealants
- ASTM-C962 - Guide for Use of Elastomeric Joint Sealants (Withdrawn 1992)
- ASTM-C963 - Standard Specification for Packaging, Identification, Shipment, and Storage of Lock-Strip Gaskets
- ASTM-C964 - Standard Guide for Lock-Strip Gasket Glazing
- ASTM-C97 - Standard Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone
- ASTM-C972 - Standard Test Method for Compression-Recovery of Tape Sealant
- ASTM-C99 - Standard Test Method for Modulus of Rupture of Dimension Stone
- ASTM-D2202 - Standard Test Method for Slump of Sealants
- ASTM-D2203 - Standard Test Method for Staining from Sealants
- ASTM-D2249 - Standard Test Method for Predicting the Effect of Weathering on Face Glazing and Bedding Compounds on Metal Sash (Withdrawn 2002)
- ASTM-D2376 - Standard Test Method for Slump of Face Glazing and Bedding Compounds on Metal Sash (Withdrawn 2002)
- ASTM-D2377 - Standard Test Method for Tack-Free Time of Caulking Compounds and Sealants
- ASTM-D2450 - Standard Test Method for Bond of Oil- and Resin-Base Caulking Compounds (Withdrawn 2002)
- ASTM-D2451 - Standard Test Method for Degree of Set for Glazing Compounds on Metal Sash (Withdrawn 2002)
- ASTM-D2452 - Standard Test Method for Extrudability of Oil- and Resin-Base Caulking Compounds
- ASTM-D2453 - Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds
- ASTM-D2859 - Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials
- ASTM-E108 - Standard Test Methods for Fire Tests of Roof Coverings
- ASTM-E119 - Standard Test Methods for Fire Tests of Building Construction and Materials
- ASTM-E1317 - Standard Test Method for Flammability of Surface Finishes
- ASTM-E1321 - Standard Test Method for Determining Material Ignition and Flame Spread Properties
- ASTM-E1352 - Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies (Withdrawn 2022)
- ASTM-E1353 - Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture (Withdrawn 2022)
- ASTM-E1354 - Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
- ASTM-E1355 - Standard Guide for Evaluating the Predictive Capability of Deterministic Fire Models
- ASTM-E136 - Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750°C
- ASTM-E1472 - Standard Guide for Documenting Computer Software for Fire Models (Withdrawn 2011)
- ASTM-E1474 - Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
- ASTM-E1529 - Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
- ASTM-E1537 - Standard Test Method for Fire Testing of Upholstered Furniture
- ASTM-E1546 - Standard Guide for Development of Fire-Hazard-Assessment Standards
- ASTM-E1590 - Standard Test Method for Fire Testing of Mattresses
- ASTM-E1591 - Standard Guide for Obtaining Data for Fire Growth Models
- ASTM-E162 - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
- ASTM-E1623 - Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)
- ASTM-E1678 - Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis
- ASTM-E1725 - Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components
- ASTM-E1740 - Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
- ASTM-E176 - Standard Terminology of Fire Standards
- ASTM-E1776 - Standard Guide for Development of Fire-Risk-Assessment Standards
- ASTM-E1822 - Standard Test Method for Fire Testing of Stacked Chairs
- ASTM-E1895 - Standard Guide for Determining Uses and Limitations of Deterministic Fire Models (Withdrawn 2011)
- ASTM-E1966 - Standard Test Method for Fire-Resistive Joint Systems
- ASTM-E1995 - Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally
- ASTM-E2010 - Standard Test Method for Positive Pressure Fire Tests of Window Assemblies (Withdrawn 2007)
- ASTM-E2032 - Standard Practice for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119
- ASTM-E2058 - Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA)
- ASTM-E2061 - Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles
- ASTM-E2067 - Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests
- ASTM-E2074 - Standard Test Method for Fire Tests of Door Assemblies, Including Positive Pressure Testing of Side-Hinged and Pivoted Swinging Door Assemblies (Withdrawn 2007)
- ASTM-E2102 - Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
- ASTM-E2187 - Standard Test Method for Measuring the Ignition Strength of Cigarettes
- ASTM-E2203 - Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
- ASTM-E2226 - Standard Practice for Application of Hose Stream
- ASTM-E2230 - Standard Practice for Thermal Qualification of Type B Packages for Radioactive Material
- ASTM-E2231 - Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
- ASTM-E2257 - Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
- ASTM-E2280 - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
- ASTM-E2307 - Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus
- ASTM-E2335 - Standard Guide for Laboratory Monitors
- ASTM-E2336 - Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
- ASTM-E2404 - Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) and Wood Wall or Ceiling Coverings, Facings and Veneers, to Assess Surface Burning Characteristics
- ASTM-E2405 - Standard Test Method for Determination of Fire and Thermal Parameters of Materials Using an Intermediate Scale Test with Vertically Oriented Specimen (Withdrawn 2011)
- ASTM-E2536 - Standard Guide for Assessment of Measurement Uncertainty in Fire Tests
- ASTM-E2573 - Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics
- ASTM-E2574 - Standard Test Method for Fire Testing of School Bus Seat Assemblies
- ASTM-E2579 - Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
- ASTM-E2599 - Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics
- ASTM-E2632 - Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials
- ASTM-E2652 - Standard Test Method for Assessing Combustibility of Materials Using a Tube Furnace with a Cone-shaped Airflow Stabilizer, at 750 °C
- ASTM-E2653 - Standard Practice for Conducting an Interlaboratory Study to Determine Precision Estimates for a Test Method with Fewer Than Six Participating Laboratories
- ASTM-E2688 - Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics
- ASTM-E2690 - Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics
- ASTM-E2707 - Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure
- ASTM-E2726 - Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands
- ASTM-E2748 - Standard Guide for Fire-Resistance Experiments
- ASTM-E2749 - Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- ASTM-E2750 - Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814
- ASTM-E2768 - Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)
- ASTM-E2816 - Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems
- ASTM-E2837 - Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies
- ASTM-E286 - Method of Test for Surface Flammability of Building Materials Using an 8-Ft. (2.44-M) Tunnel Furnace (Withdrawn 1991)
- ASTM-E2874 - Standard Test Method for Determining the Fire-Test Response Characteristics of a Building Spandrel-Panel Assembly Due to External Spread of Fire
- ASTM-E2886 - Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement
- ASTM-E2912 - Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction
- ASTM-E2957 - Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections
- ASTM-E2965 - Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter
- ASTM-E2988 - Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics
- ASTM-E2989 - Standard Guide for Assessment of Continued Applicability of Reaction to Fire Test Reports Used in Building Regulation
- ASTM-E3020 - Standard Practice for Ignition Sources
- ASTM-E3021 - Standard Guide for Evaluating the Relative Effectiveness of Building Systems to Resist the Passage of Products of Combustion Based on the Aggregation of Leakage Rates
- ASTM-E3048 - Standard Test Method for Determination of Time to Burn-Through Using the Intermediate Scale Calorimeter (ICAL) Radiant Panel
- ASTM-E3082 - Standard Test Methods for Determining the Effectiveness of Fire Retardant Treatments for Natural Christmas Trees
- ASTM-E3134 - Standard Specification for Transportation Tunnel Structural Components and Passive Fire Protection Systems
- ASTM-E3202 - Standard Practice for Specimen Preparation and Mounting of Plastic Composites for Use as Deck Boards, Stair Treads, Guards or Handrails to Assess Surface Burning Characteristics
- ASTM-E3287 - Practice for Specimen Preparation of Fenestration Profiles Intended to Support Non-Combustible In-Fill Materials to Assess Surface Burning Characteristics
- ASTM-E3367 - Standard Test Method for Determining the Combustion Behavior of Layered Assemblies using a Cone Calorimeter
- ASTM-E535 - Standard Practice for Preparation of Fire-Test-Response Standards
- ASTM-E603 - Standard Guide for Room Fire Experiments
- ASTM-E648 - Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source
- ASTM-E662 - Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials
- ASTM-E719 - Test Method for Indentation of Building Materials Surfaces Under Concentrated Loads as a Measure of Serviceability (Withdrawn 1987)
- ASTM-E800 - Standard Guide for Measurement of Gases Present or Generated During Fires
- ASTM-E814 - Standard Test Method for Fire Tests of Penetration Firestop Systems
- ASTM-E84 - Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM-E842 - Specification for Lawn Buildings (Withdrawn 1990)
- ASTM-E843 - Specification for Covers, Carports, and Canopies (Withdrawn 1990)
- ASTM-E906 - Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
- ASTM-E931 - Practice for Classification of Occupancies for Their Relative Fire Hazard (Withdrawn 1996)
- ASTM-E970 - Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
- ASTM-ES35 - Test Methods for the Analysis of Digested Samples for Lead by Inductively Coupled Plasma (ICP-AES) Flame Atomic Absorption (FAAS), or Graphite Furnace Atomic Absorption (GFAAS) Techniques (Withdrawn 1994)
- ASTM-ES36 - Practice for Hot Plate Digestion of Dust Wipe Samples for the Determination of Lead by Atomic Spectrometry (Withdrawn 1995)
- ASTM-F1103 - Test Method for Materials Response to Flame--45 Degree (For Aerospace Vehicles) (Withdrawn 1998)
- ASTM-F501 - Test Method for Aerospace Materials Response to Flame, with Vertical Test Specimen (For Aerospace Vehicles Standard Conditions) (Withdrawn 1998)
- ASTM-F814 - Test Method for Specific Optical Density of Smoke Generated by Solid Materials for Aerospace Applications (Withdrawn 1995)
- ASTM-F828 - Test Method for Radiant Heat Resistance of Aircraft Inflatable Evacuation Slide/Slide Raft Materials (Withdrawn 1995)