FSC 8030: Preservative and Sealing Compounds
The following documents are a part of this series:
ASTM:
US GOVERNMENT DOCUMENTS:
- A-A-1500 - Sealer, Surface (Latex Block Filler)
- A-A-1556 - Sealing Compound (Elastomeric Joint Sealants)
- A-A-2210 - Filler, Wood, Paste
- A-A-2542 - Sealer, Terrazo & Concrete Floors, Waterbased
- A-A-2702 - Sealing Compound (Liquid Protectant & 'Beautifier')
- A-A-272 - Caulking Compounds
- A-A-2817 - Tire Puncture Sealant & Inflator
- A-A-2884 - Neat'S-Foot Oil
- A-A-2982 - Coating Compound, Bituminous, Fillers, Solvent Type, Aluminum Pigmented
- A-A-2985 - Adhesive, Air-Cure, Silicone Rubber
- A-A-3110 - Plumbing Fixture Setting Compound
- A-A-3133 - Filler, Two-Component Type (for Dents, Cracks, Small Holes, & Blow Holes)
- A-A-373 - Glazing Compound, Sash (Metal) for Back Bedding and Face Glazing (Not for Channel or Stop Glazing) Replaced by ASTM-C669
- A-A-378 - Putty: Linseed Oil Type, (for Wood-Sash-Glazing)
- A-A-52408 - Preservative Coating, Rubber: for Rubber Surfaces
- A-A-52495 - Sealing Compound, Non-Curing, Polybutene
- A-A-56025 - Paste, Conductive
- A-A-58092 - Tape, Antiseize, Polytetrafluorethylene
- A-A-59258 - Tape, Aluminum Foil, Heat Reflective, Pressure Sensitive Adhesive
- A-A-59276 - Wood Preservatives: Waterborne or Water Reducible
- A-A-59293 - Sealing Compound, Adhesive: Curing (Polysulfide Base)
- A-A-59295 - Corrosion Preventive Compounds, Cold Application (for New and Fielded Motor Vehicles and Trailers)
- A-A-59313 - Thread Compound; Antiseize, Zinc Dust-Petroleum
- A-A-59464 - Plastic Plastisol (for Coating Metallic Objects)
- A-A-59491 - Sealing Compound, Thread and Gasket, Hydrocarbon Fluid and Water Resistant
- A-A-59719 - One Hundred Percent Polyurethane Sprayed on Linings
- A-A-59885 - Corrosion Prevention Compound
- AMS-3269 - Sealing Compound, Polysulfide (T) Synthetic Rubber, for Integral Fuel Tank and Fuel Cell Cavities, High Strength, for Intermittent Use to 360 Deg F (182 Deg C) (STABILIZED Sep 2011)
- AMS-3281 - Sealing Compound, Polysulfide (T) Synthetic Rubber For Integral Fuel Tank and Fuel Cell Cavities Low Density (1.20 to 1.35 sp gr), for Intermittent Use to 360°F (182°C)
- AMS-3284 - Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates
- AMS-5791 - Cobalt Alloy, Powder, Plasma Spray, 56.5Co - 25.5Cr - 10.5Ni- 7.5W
- AMS-C-27725 - Coating, Corrosion Preventative, for Aircraft Integral Fuel Tanks for Use to 250 °F (121 °C)
- AMS-S-4383 - Sealing Compound, Topcoat, Fuel Tank Buna-N Type
- AMS-S-7124 - Sealing Compound, Polysulfide, Accelerator Required, for Aircraft Structures (STABILIZED Sep 2011)
- AMS-S-7916 - Compound, Sealing, Thread and Gasket, Fuel, Oil, and Water Resistant
- AMS-S-83318 - Sealing Compound, Polysulfide Type, Low Temperature Curing, Quick Repair, Integral Fuel Tanks and Fuel Cell Cavities
- AMS-S-85420 - Sealing Compounds, Quick Repair, Low Temperature Curing Polysulfide, for Aircraft Structures (STABILIZED Sep 2011)
- AWPA-M4 - Standard for the Care of Preservative-Treated Wood Products
- AWPA-P11 - Creosote-Pentachcorophenol Wood Preservative Solution, Standard for
- AWPA-P7 - Standard for Field Cuts, Creosote for Brush or Spray Treatment
- BU-535 - Free Diisocyanate Test Method
- C-N-200 - Neats-Foot Oil
- DOD-C-24176 - Cement, Epoxy, Metal Repair and Hull Smoothing (Metric)
- DOD-C-2687 - Compound, Battery Sealing (Metric)
- DOD-R-18708 - Rust Arresting Coating, Shipboard Exterior, Gray, Navy Formulas #123g (Cancelled, 1990, No Superseding Document)
- DOD-S-82708 - Sealing Compound, Preformed (Metric) (Inactive for New Design)
- HH-C-536 - Compound, Plumbing-Fixture-Setting (Cancelled, 1977, No S/Sdocument)
- HH-T-30 - Tape, Pipe Coating, Coal Tar, Hot Applied, and Primer +Cancelled, 1977, No S/S Documen
- JAN-A-669 - Anti-Seize-Compound, White-Lead-Base, General-Purpose (for Threaded Fittings) (Use TT-A-580)
- JAN-C-168 - Compound, Calking (for Wooden Vessels) (Superseded by MIL-C-18969a)
- JAN-C-693 - Cement, Metallurgical, Air-Setting, High Temperature
- JAN-P-115 - Packaging and Packing for Overseas Shipment - Compound, Sealing, Dipcoating
- JAN-P-604 - Protective Coating System, Phonolic Resin Base, Heat-Hardening for the Interiors of Potable-Water Tanks
- L-T-1512 - Tape, Pressure Sensitive Adhesive, Pipe Wrapping
- L-T-80 - Tape, Pressure-Sensitive Adhesive (Aluminum-Backed)
- MIL-A-12352 - Antiseize Compound, Threads, for Steam and Water Lines (Use TT-S-1732)
- MIL-A-13881 - Anti-Seize Compound, Mica-Base (for Threaded Fittings) (No Superseding Document)
- MIL-A-38267 - Application of Polyurethane Fuel Tank Coatings (No Superseding Document)
- MIL-A-907 - Antiseize Thread Compound, High Temperature
- MIL-C-102 - Coating Compound, Bituminous, Solvent Cut Back, Box and Crate Topcoating
- MIL-C-10382 - Corrosion Preventive, Petrolatum, Spraying Application: for Food Handling Machinery and Equipment
- MIL-C-10506 - Coating, Exterior for Tinned Food Cans (Use TT-C-495)
- MIL-C-1068 - Compound, Water-Repellent, Textile Finish
- MIL-C-11080 - Coating, Corrosion-Resistant (No Superseding Document)
- MIL-C-11728 - Compound, Corrosion-Inhibiting and Lubricating, for Gas Cylinder Cap Threads
- MIL-C-11794 - Compound, Caulking
- MIL-C-11796 - Corrosion Preventive Compound, Petrolatum, Hot Application
- MIL-C-12178 - Corrosion-Preventive Compound, Trifluorovinyl Chloride, for Use With Oxygen Equipment
- MIL-C-1219 - Cement, Iron and Steel (Superseded by QQ-C-100)
- MIL-C-12599 - Coating, Clear, Acrylic (Pressurized Dispenser) (Use TT-L-50)
- MIL-C-13125 - Compound: Mounting for Optical Lens Blanks (No Superseding Document)
- MIL-C-13370 - Coating Material, Heat-Resistant, for Ferrous Surfaces (No Superseding Document)
- MIL-C-13388 - Compound, Asphaltic, Fire Retardant
- MIL-C-13704 - Cement, Sealing or Plugging
- MIL-C-13783 - Compound, Waterproofing (for Small Arms Ammunition) (No Superseding Document)
- MIL-C-13950 - Coating Compound, Bituminous, Solvent (for Railway Rolling Stock)
- MIL-C-15074 - Corrosion Preventive, Fingerprint Remover
- MIL-C-15203 - Coating Compound, Bituminous, Emulsion Type, Coal Tar Base (No Superseding Document)
- MIL-C-15705 - Calking Compound (Liquid Polymer Polysulfide Synthetic Rubber; Formula No. 112, for Metal Enclosures) (No Superseding Document)
- MIL-C-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application
- MIL-C-16555 - Coating Compound, Strippable, Sprayable
- MIL-C-16558 - Coating, Organic (for Covering Struts and Other Exposed Surfaces)
- MIL-C-18255 - Calking Compound, Synthetic Rubber Base, Wooden Deck Seam Application (See Notice 1 for Replacement Information)
- MIL-C-1828 - Compound, Spray, for Upper Leather
- MIL-C-1829 - Compound, Oil, Sole Treating
- MIL-C-18480 - Coating Compound, Bituminous, Solvent, Coal-Tar Base
- MIL-C-18487 - Compound, Gun Slushing
- MIL-C-18969 - Calking Compounds Metal Seam and Wood Seam (Use MIL-C-18255)
- MIL-C-19459 - Corrosion Inhibiting Compound (for Torpedo Mark 37 Mod 0 and Related Application) (Superseded by MIL-PRF-16173)
- MIL-C-19565 - Coating Compounds, Thermal Insulation, Fire - & Water-Resistant, Vapor-Barrier
- MIL-C-19993 - Coating Compound, Fibrous Glass Thermal Insulation Board, Water Vapor Barrier (Superseded by MIL-19565 Now MIL-PRF-19565)
- MIL-C-20551 - Compound, Luting
- MIL-C-21066 - Coating System, Plastisol (Superseded by MIL-P-20689a)
- MIL-C-21067 - Coating Compound, Synthetic Rubber, for Exposed Steel Surfaces
- MIL-C-22235 - Corrosion Preventive Oil, Nonstaining (No Superseding Document)
- MIL-C-22395 - Compound, End Sealing, Thermal Insulation Pipe Covering-Fire-, Water-, and Weather-Resistant
- MIL-C-22804 - Cement, Sealing, Double Planking (No Superseding Document)
- MIL-C-23050 - Compound, Rust Retarding, Spray on Type, Ballast Tank Preservative (No Superseding Document)
- MIL-C-23112 - Corrosion Preventive, Fire Resistant (Superseded by MIL-H-19457)
- MIL-C-23403 - Compound, Soft Film, Corrosion-Preventive, Non-Staining
- MIL-C-23411 - Corrosion Preventive Compounds, Clear (Superseded by MIL-C-81309)
- MIL-C-24205 - Calking Compound, Modified Epoxy Base, Wooden Deck Seam Application
- MIL-C-26703 - Coating, Interior, for Metal Containers (Supersedes 20029)
- MIL-C-27315 - Coating, Systems, Elastomeric Thermally Reflective and Rain Erosion Resistant (Superseded by MIL-C-83445)
- MIL-C-27725 - Coating, Corrosion Preventive, for Aircraft Integral Fuel Tanks (Superseded by SAE AMS-C-27725)
- MIL-C-3004 - Coating, Fire-Resistant, Adhesive (for Repairing Surface of Fibrous Glass Insulation Board) (Use MIL-A-3316)
- MIL-C-3254 - Coating-System, Bridging, Strippable Sprayable
- MIL-C-3301 - Compound, Asphaltic, Hot Melt (Cavity Lining)
- MIL-C-38713 - Coating Compound, Elastic, Polysulfide (Superseded by MIL-S-81733 Now MIL-PRF-81733)
- MIL-C-3923 - Calking Compound
- MIL-C-40084 - Corrosion Preventive Compound, Water-Emulsifiable, Oil Type
- MIL-C-43374 - Coating Compound (Touch Up, for Air Supported Radome)
- MIL-C-4484 - Coating Plastic (for Refinishing Leather) (Supersedes 14154)
- MIL-C-450 - Coating Compound, Bituminous Solvent Type, Black (for Ammunition)
- MIL-C-46095 - Compound, Sealing, Low Temperature, Rotation
- MIL-C-46157 - Coating Compound, Temporary Protective for Retrograde Materials (No Superseding Document)
- MIL-C-47016 - Compound, Modified Silicone Rubber, Heat Resistant (No Superseding Document)
- MIL-C-47069 - Coating, Electrically Conductive, Air-Drying (No Superseding Document)
- MIL-C-47070 - Compound, Urethane (No Superseding Document)
- MIL-C-47071 - Coating, Ablative, Phenolic-Epoxy Resin System (No Superseding Document)
- MIL-C-47072 - Curing Agent, Epoxy Resin (No Superseding Document)
- MIL-C-47121 - Compound, Sealing, Polysulfide Rubber (No Superseding Document)
- MIL-C-47161 - Coating, Corrosion Resistant (No Superseding Document)
- MIL-C-47163 - Compound, Rubber, Silicone, High Dielectric Properties, Room Temperature Vulcanizing (No Superseding Document)
- MIL-C-47164 - Compound, Plastic Polyurethane (No Superseding Document)
- MIL-C-47167 - Compound, Sealant Anti-Sieze (No Superseding Document)
- MIL-C-47168 - Coating, Ablative, Spray Type High Temperature Resistant
- MIL-C-47214 - Coating, Protective, for Insulation Sheet Cork (No Superseding Document)
- MIL-C-47244 - Coating, Ablative Resistant
- MIL-C-47246 - Coatings, Ablative, Application of
- MIL-C-47247 - Coating, Protective, Resin, Silicone (No Superseding Document)
- MIL-C-62218 - Corrosion Preventive Compounds, Cold Application (for New & Fielded Motor Vehicles & T
- MIL-C-6796 - Coatings, Protective (for Wood)
- MIL-C-6798 - Coating, Rust Inhibiting (for Metal Containers)
- MIL-C-6799 - Coatings, Sprayable, Strippable, Protective, Water Emulsion
- MIL-C-7439 - Coating System, Elastomeric, Rain Erosion Resistant & Rain Erosion Resistant With Anti-Static Treatment, for Exterior Aircraft & Missile Plastic Parts (Use MIL-C-83231)
- MIL-C-81309 - Corrosion Preventive Compounds, Water Displacing, Ultra-Thin Film
- MIL-C-81384 - Coating, Sprayable, Clear, Weatherproof, for Protection of Fibrous Containers
- MIL-C-82594 - Corrosion Preventive Compound and Surface Sealer for Nonferrous Metals
- MIL-C-82604 - Compound, Asphaltic, High Melting Hot-Melt (Cavity Lining)
- MIL-C-82633 - Compound, Polymeric Elastomer, Thermosetting (for Use as Bomb Tail Pad
- MIL-C-82644 - Compounds, Epoxy, Encapsulating (No Superseding Document)
- MIL-C-82811 - Compound, Mold Release, Liquid (No Superseding Document)
- MIL-C-83019 - Coating, Polyurethane, for Protection of Integral Fuel Tank Sealing Compound
- MIL-C-83466 - Coating, Polyurethane, Aliphatic Isocyanate, Thermal Flux Resistant for Aerospace Applications (Superseded by MIL-C-83286)
- MIL-C-83933 - Corrosion Preventive Compounds Cold Application (for Motor Vehicles (No Superseding Document)
- MIL-C-83982 - Compound, Sealing, Fluid Resistant (Superseded by MIL-S-81733)
- MIL-C-85054 - Corrosion Preventive Compound, Water Displacing, Clear (Aml Guard)
- MIL-C-8507 - Coating, Wash Primer (Pretreatment) for Metals, Application of (for Aeronautical Use)
- MIL-C-8514 - Coating Compound, Metal Pretreatment, Resin-Acid (Asg)
- MIL-C-87179 - Coating, Protective, Solvent Removable, for Microcircuits (Superseded by SAE AMS-2535)
- MIL-D-16651 - Deck Covering, Lightweight, Nonslip, Nonsparking, and Sealing Compound, Fabric Deck-Covering (Use MIL-D-17951)
- MIL-D-17419 - Drawing, Engineering and Associated Documentation Preparation and Microfilming of (for Electronic Equipment
- MIL-D-9063 - Desealant, Integral Fuel and Oil Tanks (Superseded by MIL-R-81294)
- MIL-DTL-3301 - Compound, Asphaltic, Hot-Melt (Cavity Lining)
- MIL-DTL-3688 - Wax Emulsion (Rust Inhibiting)
- MIL-DTL-450 - Coating Compound, Bituminous Solvent Type, Black (for Ammunition)
- MIL-DTL-82604 - Compound, Asphaltic, High Melting Hotmelt (Cavity Lining)
- MIL-DTL-82633 - Compound, Polymeric Elastomer, Thermosetting
- MIL-DTL-85054 - Corrosion Preventive Compound, Water-Displacing, Transparent (Formerly AMLGUARD)
- MIL-E-47166 - Epoxy Cement, Conductive, Room Temperature Curing (No Superseding Document)
- MIL-F-3622 - Flame-Resistant Compound, Fabric (Colorless, Emulsifiable)
- MIL-F-46032 - Fungus-Resistant Treatment for Sandbags; Copper Processes (No Superseding Document)
- MIL-F-9118 - Finish, for Glass Fabric
- MIL-G-12376 - Gasket Forming Compound, for Petroleum Products Pipe (See MIL-S-7916
- MIL-G-26138 - Glove Set, Protective, Fire-Fighting
- MIL-G-46884 - Glass, Metal Sealing (Superseded by ASTM-F105)
- MIL-HDBK-341 - Coating, Aluminum & Silicon Diffusion, Process for
- MIL-HDBK-506 - Process for Coating, Pack Cementation, Chrome Aluminide
- MIL-HDBK-696 - Plastic Coating Compound, Strippable, Hot and Cold Dip (No Superseding Document)
- MIL-I-6869 - Impregnants for Aluminum Alloy and Magnesium Alloy Castings (Superseded by MIL-I-17563)
- MIL-L-10095 - Leather Dressing, Preservative and Mildew Preventive
- MIL-L-52696 - Laminating Resin (No Superseding Document)
- MIL-L-8067 - Leather Dressing, Mildew-Preventative (Not Superseded)
- MIL-L-87177 - Lubricants, Corrosion Preventive Compound, Water Displacing, Synthetic
- MIL-M-13295 - Mildew Resistant Compound, Textile (for Field Retreatment ) (Use TT-P-595)
- MIL-M-17222 - Mildew Resistant Compound, 2, 2, Methylenebis (4-Chlorophenol)
- MIL-M-17231 - Mildew Resistant Compound, Copper Naphthenate
- MIL-M-5658 - Mildew Proofing of Fabrics, Threads and Cordages, Copper Processes for.
- MIL-M-81999 - Molding Compound, Reversion Resistant, Non-Carcinogen Curing Polyurethane, Aircraft Structure
- MIL-N-1056 - Neat S-Foot, Oil, Sulphomated
- MIL-P-11520 - Preservative Coating, Rubber: for Rubber Surfaces (Superseded by A-A-52408)
- MIL-P-12121 - Plastic, Coating Compound, Strippable (Sprayable)
- MIL-P-149 - Plastic Coating Compound, Strippable (Hot Dipping)
- MIL-P-18623 - Plastic Coating Compound, Electrical Cable Splice Sealing, Naval Shipboard
- MIL-P-19980 - Preservative Coating, Cotton Matting, Fire-Resistant
- MIL-P-20088 - Preservation Solution Concentrate, Sonar Sea Chest (No Superseding Document)
- MIL-P-20628 - Putty, Sealing (for Bolted Steel Storage Tanks) (No Superseding Document)
- MIL-P-22841 - Paper, Masking, Pressure-Sensitive, Adhesive-Edged
- MIL-P-23236 - Paint Coating Systems, Fuel & Salt Water Ballast Tanks (Metric) Now MIL-PRF-23236
- MIL-P-23242 - Plastic Coating Compound, Strippable - Electroplating
- MIL-P-3826 - Pitch, Burgundy
- MIL-P-3840 - Paint, Camouflage, Bituminous&Emulsion Adhesive
- MIL-P-38714 - Packaging and Packing of Two Component Materi (See MIL-S-38714 (S/S Rev Level...)
- MIL-P-45021 - Plastic Coating Compound, Strippable, Cold Dipping, 120 Deg F. (49 Deg. C) (Superseded by MIL-C-6799 Now MIL-PRF-6799, MIL-C-16173 Now MIL-PRF-16173, MIL-C-16555, MIL-C-23760)
- MIL-P-47215 - Primer, Ablative Resistant Coating
- MIL-P-8045 - Plastic, Self-Sealing and Non-Self-Sealing Tank Backing Material
- MIL-P-8116 - Putty, Zinc Chromate, General Purpose
- MIL-P-83455 - Potting Compound, Two Component, Rtv, Fluorosilicone (No Superseding Document)
- MIL-P-906 - Preservative, Wood, Water-Repellent (Superseded by TT-W-572)
- MIL-PRF-16173 - Corrosion Preventative Compound, Solvent Cutback, Cold-Application
- MIL-PRF-18487 - Compound, Gun Slushing
- MIL-PRF-19565 - Coating Compounds, Thermal Insulation, Fire and Water Resistant, Vapor Barrier
- MIL-PRF-23586 - Sealing Compound (With Accelerator), Silicone Rubber, Electrical
- MIL-PRF-24176 - Cement, Epoxy, Metal Repair and Hull Smoothing (Metric)
- MIL-PRF-3043 - Resin Coating, Permanent, for Engine Components and Metal Parts
- MIL-PRF-62218 - Corrosion Preventive Compounds, Cold Application (for New and Fielded Motor Vehicles and Trailers) (Replaced by A-A-59295)
- MIL-PRF-6799 - Coatings, Sprayable, Strippable, Protective, Water Emulsion
- MIL-PRF-8116 - Putty, General Purpose, Non-Hardening
- MIL-PRF-81309 - Corrosion Preventive Compounds, Water Displacing, Ultra-Thin Film
- MIL-PRF-81733 - Sealing and Coating Compound, Corrosion Inhibitive
- MIL-PRF-81904 - Coating Compound, Thermal-Insulation
- MIL-PRF-83483 - Antiseize Thread Compound, Molybdenum Disulfide-Petrolatum
- MIL-PRF-8516 - Sealing Compound, Synethetic Rubber, Electric Connectors and Electric Systems, Chemically Cured
- MIL-PRF-907 - Antiseize Thread Compound, High Temperature
- MIL-R-10036 - Rust Arresting Coating (for Treatment of Rusted Metal) (No Superseding Document)
- MIL-R-20091 - Rubber (Synthetic) and Cement for Lining Ferrous Pipe and Fittings (for Saltwater, Lines)
- MIL-R-21006 - Rust Retarding Compound, Flotation Type, Ballast Tank Protective (No Superseding Document)
- MIL-R-3043 - Resin Coating, Unpigmented, for Engine Components & Metal Parts
- MIL-R-46082 - Retaining Compounds, Single Component, Anaerobic
- MIL-R-47013 - Rubber, Butyl, Special Grade (No Superseding Document)
- MIL-R-47120 - Rubber, Butyl (Resin Cured), Short Term Resistant To Hydrazine Type Fuels and Irfna (No Superseding Document)
- MIL-R-53086 - Rust Converter, Metric (No Superseding Document)
- MIL-R-6800 - Resin Coating, Permanent, for Aircraft Engine Parts, Application of (No Superseding Document)
- MIL-R-82804 - Resin, Epoxy, Liquid (No Superseding Document)
- MIL-S-11030 - Sealing Compound, Single-Component, Non-Curing, Polysulfide Base
- MIL-S-11031 - Sealing Compound, Adhesive. Curing (Polysulfide Base) (Superseded by A-A-59293)
- MIL-S-11388 - Sealing Material for Metal Container Seams
- MIL-S-11515 - Sealing Tape, Wood-To-Metal and Metal-To-Metal Surfaces, Asphalt Base, Cotton Backed, Waterproof
- MIL-S-12158 - Sealing Compound, Non-Curing, Polybutene (Superseded by A-A-52495)
- MIL-S-12243 - Sealing Compound, for Waterproofing Welding Electrodes.
- MIL-S-14231 - Sealing Compound, Joint, Two Component, for Bolted Aluminum or Steel Petroleum-Storage Tanks (No Superseding Document)
- MIL-S-15204 - Sealing Compound, Joint and Thread, High Temperature
- MIL-S-17175 - Sealing Compound, Asphalt Base, for Ammunition
- MIL-S-17377 - Sealing Compound, Boiler Casting (Reinstated 09/06/88)
- MIL-S-19653 - Sealing Compound (Wood Bedding), Fortified
- MIL-S-22473 - Sealing, Locking, and Retaining Compounds: (Single Component) (Superseded by ASTM-D5363)
- MIL-S-23498 - Sealing Compound, Bearing Preservation, Synthetic Rubber Base (No Superseding Document)
- MIL-S-23586 - Sealing Compound, Electrical, Silicone Rubber, Accelerator Required
- MIL-S-24340 - Sealing Compound, Deck Polyurethane (Polyether Base)
- MIL-S-24522 - Sealer, Deck Covering (Superseded by TT-S-223)
- MIL-S-2869 - Sealing Compound, Synthetic Rubber, Hose Cover Repair (No Superseding Document)
- MIL-S-29574 - Sealing Compound, Polythioether, for Aircraft Structures, Fuel and High Temperature Resistant, Fast Curing at Ambient and Low Temperature (Superseded by SAE AMS-3277, See Notice 1 for Additional Information)
- MIL-S-3105 - Sealing Compound, Inert (for Use in Ammunition)
- MIL-S-3802 - Sealer for Automotive Application
- MIL-S-38228 - Sealing Compound, Environmental, for Aircraft Surfaces
- MIL-S-38249 - Sealing Compound, Firewall (Superseded by SAE AMS-3374)
- MIL-S-38714 - Sealing Cartridge for Two Component Materials
- MIL-S-3927 - Sealing Compound, Thread, Polymerizing Room Temperature (Superseded by MIL-S-46163 and MIL-S-22473
- MIL-S-40083 - Sealing and Retaining Compounds, Thread, Single Component
- MIL-S-4383 - Sealing Compound, Topcoat, Fuel Tank, BUNA-N Type (Superseded by SAE AMS-S-4383)
- MIL-S-45180 - Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant
- MIL-S-46163 - Sealing, Lubricating and Wicking Compounds: Thread-Locking, Anaerobic, Single-Component
- MIL-S-46897 - Sealing Compound, Polyurethane Foam (No Superseding Document)
- MIL-S-47015 - Sealer, Flexible Ablative (No Superseding Document)
- MIL-S-47122 - Sealing Compound (No Superseding Document)
- MIL-S-47123 - Sealant, Ablative, Silicone Base, Room Temperature Curing, and Primer (No Superseding Document)
- MIL-S-47162 - Sealant, Silicone Rubber Room Temperature Vulcanizing (No Superseding Document)
- MIL-S-47165 - Sealing Compound, High Tear Strength (No Superseding Document)
- MIL-S-47169 - Sealant, Filled Epoxy, for Gyroscopic Devices (No Superseding Document)
- MIL-S-47245 - Sealant, Electrically Conductive (No Superseding Document)
- MIL-S-47294 - Sealant, Silicone Rubber, Rtv, Non-Acetic Acid Evolving (No Superseding Document)
- MIL-S-48112 - Sealing Compound Butyl Rubber Sealant (for Use in Ammunition) (No Superseding Document)
- MIL-S-5817 - Sealant, Fuel Tank, Polysulfide Polymer, Solvent-Type
- MIL-S-7124 - Sealing Compound, Polysulfide, Accelerator Required, for Aircraft Structures (Superseded by SAE AMS-S-7124)
- MIL-S-7126 - Sealing Compounds, Synthetic Glass (Use MIL-S-11030 and MIL-S-7124)
- MIL-S-7502 - Sealing Compound, Integral Fuel Tanks and Fuel Cell Cavities, High Adhesion, Accelerator Required (Superseded BYMIL-S-8802)
- MIL-S-7916 - Sealing Compound, Thread and Gasket, Fuel, Oil, and Water Resistant (Superseded by SAE as-S-7916)
- MIL-S-81323 - Sealing Compound, Non-Curing, (-65 Deg F To 350 Deg F) Groove Injection (for Integral Fuel Tanks)
- MIL-S-8141 - Strippable Plastic Coating, Sprayable (Supersedes MIL-P-3038 for AF Use)
- MIL-S-81732 - Sealing Compound, Electrical, High Strength, Accelerator Required (No Superseding Document)
- MIL-S-81733 - SEALING and COATING COMPOUND, CORROSION INHIBITIVE
- MIL-S-82793 - Sealant, Uf 3195 (No Superseding Document)
- MIL-S-83315 - Sealing Compound, Aluminum Structure, Pressure and Weather Sealing, Low Density (No Superseding Document)
- MIL-S-83318 - Sealing Compound, Low Temperature Curing, Quick Repair Integral Fuel Tanks and Fuel Cell Cavities (Superseded by SAE AMS--S-83318)
- MIL-S-83384 - Silicone, Encapsulant, Room Temperature Curing, for Space Applications
- MIL-S-83430 - SEALING COMPOUND, INTEGRAL FUEL TANK and FUEL CELL
- MIL-S-83432 - Sealing Compounds, Adhesive Bonded Structure (No Superseding Document)
- MIL-S-8516 - Sealing Compound, Synethetic Rubber, Electric Connectors and Electric Systems, Chemically Cured
- MIL-S-85312 - Sealing Compound, Noncuring, Polysulfide, Groove Injection, for Integral Fuel Tanks (No Superseding Document)
- MIL-S-85318 - Sealing Compound, Non-Carcinogen Curing Polyurethane (Polyether-Based), Electric Connectors and Electric Systems
- MIL-S-85334 - Sealing Compound, Noncuring, Low Consistency, Silicone, Groove Injection, for Integral Fuel Tanks
- MIL-S-85420 - Sealing Compounds, Quick Repair, Low Temperature Curing Polysulfide, for Aircraft Structures
- MIL-S-8784 - Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates
- MIL-S-8802 - Sealing Compound, Temperature-Resistant, Integral Fuel Tanks and Fuel Cell Cavities, High-Adhesion (Superseded by SAE AMS-S-8802)
- MIL-STD-1371 - Inspection Procedure for Anaerobic Thread Locking Compounds
- MIL-STD-340 - Coating, Pack Cementation, Chrome Aluminide, Process for (Superseded by MIL-HDBK-506)
- MIL-STD-341 - Coating, Aluminum and Silicon Diffusion, Process for (Superseded by MIL-HDBK-341)
- MIL-T-11293 - Treatment, Mildew Resistant Copper Process (for Fabrics, Threads and Cordages).
- MIL-T-13867 - Treatment, Moisture and Fungus Resistant for Fire Control Electrical and Electronic Instruments and Equipment (No Superseding Document)
- MIL-T-22361 - Thread Compound, Antiseize, Zinc Dust-Petrolatum (Superseded by A-A-59313)
- MIL-T-27730 - Tape, Antiseize, Tetrafluoroethylene, With Dispenser (Superseded by A-A-58092)
- MIL-T-4053 - Tape, Pressure-Sensitive, Adhesive (Corrosion-Resistant)
- MIL-T-45035 - Treatment, Mildew Resistant, Non-Copper Processes for Cotten Duck, Webbing and Sewed Items (Superseded by CCC-D-950)
- MIL-T-47012 - Tape, Pressure-Sensitive Adhesive, Copper Foil (No Superseding Document)
- MIL-T-47014 - Tape, Aluminum Foil, Pressure-Sensitive, Heat Reflective (Superseded by A-A-59258)
- MIL-T-5542 - Thread Compound, Anti Seize Oxygen Systems (Superseded by MIL-G-27617, Now MIL-PRF-27617)
- MIL-T-5544 - Thread Compound, Antiseize, Graphite-Petrolatum (Superseded by SAE AMS-2518)
- MIL-T-81287 - Tape, Pressure-Sensitive Adhesive, Aluminum Foil Backed, for High Temperature Application (No Superseding Document)
- MIL-T-83483 - Antiseize Thread Compound, Molybdenum Disulfide-Petrolatum (SEE: MIL-PRF-83483)
- MIL-W-10427 - Water-Repellent Compound, Filter Material Finish
- MIL-W-13518 - Wood Preservative: Tetrachlorophenol and Pentachlorophenol Surface Sealing Compound (No Superseding Document)
- MIL-W-18142 - WOOD PRESERVATIVE SOLUTIONS, OIL SOLUBLE, SHIP and BOAT USE
- MIL-W-20298 - Waterproofing Compound
- MIL-W-3172 - Wax, Laboratory (Chattertons Compound)
- MIL-W-3354 - Water-Repellent Treatment (for Glass Fabric)
- MIL-W-3688 - Wax Emulsion (Rust Inhibiting)
- MIL-W-46101 - Wood Preservation, Water Repellent (for Wood To Be Painted)
- MIL-W-71125 - Wood Preservatives: Waterborne or Water Reducible (Superseded by A-A-59276)
- MS-18069 - Compounds, Adhesive, Aircraft Design and Use Limitations for Threaded Components Retained, Sealed or Locked By
- MS-35496 - Antiseize Compound
- MS-35498 - Calking Compound
- MS-35504 - Coating, Compound, Bituminous Emulsion
- MS-35505 - Coating, Compound, Bituminous Solvent
- MS-35506 - Coating, Exterior, Air-Drying, for 1 Ton Containers
- MS-35510 - Compound, Calking, Plastic
- MS-35516 - Corrosion Resistant Coating, Chemically Treated Aluminum.
- MS-35538 - Glazing Compound, Sash
- MS-35551 - Mildew Resistant Compound, Textile
- MS-35554 - Paint, Acid, Proof
- MS-35604 - Preservative Coating, Canvas
- MS-35615 - Putty
- MS-35620 - Sealing Compound
- MS-35621 - Sealing Compound
- MS-35639 - Wood Preservative, Copper Naphthenate
- MS-35640 - Wood Preservative, Pentachlorophenol Mixture
- MS-35641 - Wood Preservative, Pentachlorophenol Mixture
- MS-35694 - Coating Compound, Metal Pretreatment, Resin-Acid
- MS-35699 - Wood Preservative, Acid Copper Chromate, Colors, Container Sizes, and Use Characteristics Thereof (Use TT-W-546)
- MS-35700 - Wood Preservative, Ammonical Copper Arsenite (Use TT-W-549)
- MS-35701 - Wood Preservative, Chromated Zinc Chloride (Use TT-W-551)
- MS-35702 - Wood Preservative, Wolman Salt
- MS-35708 - Coating Compound, Bituminous Solvent Type (Use MIL-C-13950)
- MS-35710 - Corrosion Preventive Compound, Hot Application (Use MIL-C-15167)
- MS-35729 - Wood Preservative, Pentachlorophenal Mixture (Use MIL-W-18142)
- MS-35742 - Coating Compound, Bituminous Solvent, Colors, Container Sizes, and Use Characterisics Thereof (Use MIL-P-1227)
- O-B-160 - Belt Dressing, Leather +Cancelled, 1979, No S/S Document+
- O-G-93 - Galvanizing Repair Compound +Cancelled, 1967, No S/S Document+
- O-L-164 - Leather Dressing, Mildew-Preventive
- O-L-169 - Leather Dressing, Transmission-Belt +Cancelled, S/Sby O-B-160
- O-L-172 - Leather Dressing, Vesicant Gas Resistant
- QPL-10036 - Rust Arresting Coating (for Treatment of Rusted Metal) (No Superseding Document)
- QPL-10036-12 - Rust Arresting Coating (for Treatment of Rusted Metal)
- QPL-102 - Coating Compound, Bituminous, Solvent Cutback, Box and Crate Topcoating (No Superseding Document)
- QPL-11030 - Sealing Compound, Non-Curing, Polysulfide Base
- QPL-11031 - Sealing Compound Adhesive, Curing (Polysulfide)
- QPL-11520 - Preservative Coating, Rubber, for Rubber Surfaces (No Superseding Document)
- QPL-11796 - Corrosion Preventive Compound, Petrolatum Hot Application
- QPL-12158 - Sealing Compound, Non-Curing, Polybutene
- QPL-14201 - Corrosion Preventive, Soft Film, Cold Application (Use MIL-C-16173)
- QPL-14231 - Sealing Compound, Joint, Two & Component, for Bolted Aluminum or Steel Petroleum-Storage Tanks (No Superseding Document)
- QPL-149 - Plastic Coating Compound, Strippable (Hot Dipping)
- QPL-15074 - Corrosion Preventive, Fingerprint Remover
- QPL-15076 - Protective-Coating-Material, (Polymer-Powder ) Product of an Organic Dihalide and an Inorganic Polysulfide
- QPL-15143 - Protective-Coating (Heat-Hardening), Phenol-Formaldehyde
- QPL-15159 - Preservative Coating, Canvas (Use TT-P-595)
- QPL-15203 - Coating Compound, Bituminous, Emulsion Type
- QPL-15204 - Sealing Compound, Joint and Thread, High Temperature
- QPL-15205 - Metal Conditioning Compound
- QPL-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application (Replaced by the Qualified Products Database (QPD) see Notice 1 for Additional Information)
- QPL-16555 - Coating Compound, Strippable, Sprayable
- QPL-16558 - Coating, Organic (for Covering Shafts, Struts, and Other Exposed Surfaces)
- QPL-17377 - Sealing Compound, Boiler-Casing
- QPL-18255 - Calking compound, Synthetic Rubber Base, Wooden Deck Seam Application
- QPL-18487 - Compound, Gun Slushing
- QPL-18623 - Plastic Coating Compound, Electrical Cable Splice Sealing, Naval Shipboard
- QPL-18969 - Calking Compound, Metal Seam and Wood Seam
- QPL-19565 - Coating Compound, Thermal Insulation, Fire-and Water-Resistant, Vapor-Barrier
- QPL-19653 - Sealing Compound (Wood Bedding) Fortified (No Superseding Document)
- QPL-21066 - Coating System, Polyvinyl Chloride-Plasticizer Dispersion (Plastisol)
- QPL-21067 - Coating Compound, Synthetic Rubber, Exposed Steel Surfaces
- QPL-21595 - Tape, Pressure Sensitive Adhesive, Paper, Masking, Non-Staining
- QPL-23112 - Corrosion Preventive, Fire Resistant (See Notice for Replacement Information)
- QPL-23142 - Tape, Pressure-Sensitive Adhesive, for Dissimilar Metal Separation (No Superseding Document)
- QPL-23498 - Sealing Compound Bearing Preservation Synthetic Rubber Base (No Superseding Document)
- QPL-23586 - Sealing Compound, (With Accelerator), Silicone Rubber, Electrical
- QPL-24176 - Cement, Epoxy, Metal Repair and Hull Smoothing (Metric)
- QPL-24205 - Calkink Compound, Modified Epoxy Base, Wooden Deck Seam Application
- QPL-24340 - Sealing Compound, Deck Polyurethane (Polyether Base)
- QPL-25506 - Resin, Silicone, Low-Pressure Laminating (No Superseding Document)
- QPL-27315 - Coating Systems, Elastomeric, Thermally Reflective & Rain Erosion Resistant (See Notice for Replacement Information)
- QPL-27725 - Coating, Corrosion Preventive, for Aircraft Integral Fuel Tanks (Users May Refer To PRI-QPL-AMS-C-27725)
- QPL-2912 - Synthetic Rubber Compound, Acid and Oil Resistant (for Lining Battery Compartments on Submarines)
- QPL-3105 - Sealing Compound, Inert (For Use in Ammunition)
- QPL-3254 - Coating&System, Bridging, Strippable Sprayable
- QPL-3301 - Compound, Asphaltic, Hot-Melt (Cavity Lining)
- QPL-3927 - Thread Sealing Composition, Room Temperature Polymerizing
- QPL-40084 - Corrosion Preventive Compound, Water-Emulsifiable, Oil Type (No Superseding Document)
- QPL-4383 - Sealing Compound, Topcoat, Fuel Tank, BUNA-N Type (Superseded by QPL-AMS-S-4383)
- QPL-450 - Coating Compound, Bituminous Solvent Type, Black (For Ammunition)
- QPL-45021 - Plastic Coating Compound, Strippable, Cold Dipping 120 Deg., F. (49 Deg. C)
- QPL-5542 - Thread Compound, Anti Seize Oxygen System (No Superseding Document)
- QPL-62218 - Corrosion Preventive Compounds, Cold-Application (for New and Fielded Motor Vehicles and Trailers) (No Superseding Document)
- QPL-6799 - Coatings, Sprayable, Stripple, Protective Water Emulsion
- QPL-6869 - Impregnants for Aluminum Alloy and Magnesium Alloy Castings
- QPL-7124 - Sealing Compound, Polysulfide, Accelerator Required, for Aircraft Structures (No Superseding Document)
- QPL-7126 - Sealing Compound, Synthetic Glass
- QPL-7439 - Coating System, Elastomeric, Rain Erosion Resistant and Rain Erosion Resistant With Anti-Static Treatment, for Exterior Aircraft and Missile Plastic Parts (No Superseding Document)
- QPL-7502 - Sealing Compound, Integral Fuel Tanks and Fuel Cell Cavities High Adhesion, Accelerator Required
- QPL-7916 - Sealing Compound, Thread and Gasket, Fuel, Oil and Water Resistant
- QPL-8045 - Plastic, Self-Sealing Tank Backing Material
- QPL-8067 - Leather Dressing, Fungus-Preventative
- QPL-81287 - Tape, Pressure-Sensitive Adhesive, Aluminum Foil Backed, for High Temperature Application (No Superseding Document)
- QPL-81309 - Corrosion Preventive Compounds, Water Displacing, Ultra Thin Film
- QPL-8141 - Strippable Plastic Coating, Sprayable
- QPL-81732 - Sealing Compound, Electrical, High Strength, Accelerator Required (No Superseding Document)
- QPL-81733 - Sealing and Coating Compound, Corrosion Inhibitive
- QPL-82604 - Compound, Asphaltic, High Melting Hot-Melt (Cavity Lining)
- QPL-82633 - Compound, Polymeric Elastomer, Thermosetting (for Use as Bomb Tail Pad)
- QPL-83231 - Coating, Polyurethane, Rain Erosion Resistant for Exterior Aircraft and Missile Plastic Parts (Users May Refer To PRI-QPL-AMS-C-83231)
- QPL-83315 - Sealing Compound, Aluminum Structure, Pressure and Weather Sealing, Low Density (No Superseding Document)
- QPL-83318 - Sealing Compound, Low Temperature Curing, Quick Repair, Integral Fuel Tanks and Fuel Cell Cavities (No Superseding Document)
- QPL-83430 - Sealing Compound, Integral Fuel Tanks and Fuel Cell Cavities, Intermittent Use To 360 Deg. F (182 Deg. C) (Superseded by QPL-AMS-3276)
- QPL-83455 - Potting Compound, Two Component, Rtv, Fluorosilicone (No Superseding Document)
- QPL-83933 - Corrosion Preventive Compound, Cold Application (for Motor Vehicles)
- QPL-83982 - Compound, Sealing, Fluid Resistant (No Superseding Document)
- QPL-8516 - Sealing Compound, Synthetic Rubber, Electric Connectors and Electric Systems, Chemically Cured
- QPL-85334 - Sealing Compound, Noncuring, Low Consistency, Silicone, Groove Injection, for Integral Fuel Tanks
- QPL-8784 - Sealing Compound, Aluminum Integral Fuel Tanks and Fuel Cell Cavities, Low Adhesion, Accelerator Required
- QPL-8802 - Sealing Compound, Temperature-Resistant, Integral Fuel Tanks and Fuel Cell Cavities, High-Adhesion (No Superseding Document)
- QPL-9063 - Desealant, Integral Fuel and Oil Tanks (No Superseding Document)
- QPL-907 - Antiseize Thread Compound, High Temperature (Replaced by the Qualified Products Database (QPD) see Notice for Additional Information)
- QPL-9118 - Finish, for Glass Fabric
- QPL-AMS-3276 - Sealing Compound, Integral Fuel Tanks and General Purpose, Intermittent Use To 360 Deg. F (182 Deg. C) (Users May Refer To PRI-QPL-AMS3276)
- QPL-AMS-3277 - Sealing compound, polythioether integral fuel tanks and general purpose, fast curing intermittent use to 360 degrees F (182 degrees C)
- QPL-AMS-3281 - Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities Low Density (1.35 Sp Gr Max), for Intermittent Use To 360 Deg. F (182 Deg. C) (Users May Refer To PRI-Q
- QPL-AMS-S-4383 - Sealing Compound, Topcoat, fuel Tank, Buna-N-Type
- QPL-AMS-S-7124 - Sealing Compound, Polysulfide, Accelerator Required, for Aircraft Structures
- QPL-TT-C-520 - Coating Compound, Bituminous, Solvent Type, Underbody (for Motor Vehicles)
- QPL-TT-P-595 - Preservative Coating, Canvas (No Superseding Document)
- QQ-C-100 - Cement, Iron and Steel (Cancelled, 1978, No Superseding Document)
- R-T-111 - Tar, for Joint Filler +Cancelled, 7/1/68, No S/S Document+
- SS-C-560 - Coating-Material, Fatty Acid Pitch Base, (Nonbleeding) +Cancelled, 1982, No S/S Docume
- SS-C-608 - Compounds, Jointing, Sulfur(for Bell-&-SPIGOTCAST-Iron Pipe)+Cancelled, 1975, No S/S D
- SS-P-680 - Priming-Material, Fatty Acid Pitch Base, Brushing +Cancelled, 1975, No S/S Document+
- SS-S-1401 - Sealant, Joint, Non-Jet-Fuel-Resistant, Hot-Applied, for Portland Cement and Asphalt
- SS-S-1416 - Sealing Compound, Asphalt and Concrete Surfaces +Cancelled,1976, No S/S Document+
- SS-S-156 - Sealer, Cold Application, Emulsion Type, for Joints in Concrete +Cancelled, Use Ss-S-2
- SS-S-158 - Sealing Compound, Cold-Application Ready-Mixed Liquefier +Canc, 1974, Use Ss-S-156
- SS-S-159 - Sealing Compound, Cold-Application Mastic Multiple +Cancelled, 1974, No S/S Document+
- SS-S-1614 - Sealants, Joint, Jet-Fuel-Resistant, Hot-Applied, for Portland Cement and Tar Concre
- SS-S-164 - Sealer, Hot Poured Type, for Joints in Concrete +Cancelled,1975, Use S5-S-1401
- SS-S-167 - Sealing Compound, Jet-Fuel Resistant, Hot Applied, +Cancelled, 1975, Use Ss-S-1614
- SS-S-168 - Sealing Compound, Sewer, Bituminous Two Component, +Cancelled, 1979, See Ss-S-169
- SS-S-169 - Sealer, Joint, Sewer, Mineral-Filled, Hot-Pour
- SS-S-170 - Sealing Compound, Two Components, Jet Fuel Resistant, +Cancelled, 1969, Use Ss-S-200
- SS-S-171 - Sealer, Mineral-Filled Asphalt, for Joints Inconcrete +Cancelled, 1969, Use Ss-S-1041
- SS-S-195 - Sealing Compound, Two Component, Elastomeric, +Cancelled, 1976, Use Ss-S-200
- SS-S-1996 - Sealer, Water and Weather Resistant, for Asphalt, Concrete,and Masonry Surfaces
- SS-S-200 - Sealants, Joint, Two-Component, Jet-Blast-Resistant, Cold Applied, for Portland Cement
- SS-S-210 - Sealing Compound, Preformed Plastic, for Expansion Joints & Pipe Joints
- SS-W-110 - Water-Repellent, Colorless, Silicon Resin Base
- TT-A-580 - Antiseize Compound, White Lead Base General Purpose +Cancelled, 1971, Use TT-S-1732
- TT-C-1079 - Coating Compound, Bituminous, Solvent Type; Asbestos Filled,Aluminum Pigmented
- TT-C-1796 - Calking Compounds, Metal Seam & Wood Seam
- TT-C-493 - Coating Compound, Bituminous, Solvent Type, Asphalt Base +Cancelled, 1965,Superseded By TT-C-
- TT-C-494 - Coating Compound, Bituminous, Solvent Type, Acid Resistant
- TT-C-495 - Coating, Exterior, for Tinned Food Cans
- TT-C-498 - Coating Compound, Bituminous, Fillers, Solvent Type, Aluminum Pigmented
- TT-C-517 - Coating, Strippable Masking, (for Spray Booths & Glass)
- TT-C-520 - Coating Compound, Bituminous, Solvent Type, Underbody (for Motor Vehicles)
- TT-C-598 - Calking Compound, Oil & Resin Base Type (for Building Construction)
- TT-F-340 - Filler, Wood, Plastic
- TT-G-410 - Clazing Compound, Sash (Metal) for Back Bedding +Cancelled,1980, Use ASTM-C669
- TT-P-1536 - Plumbing Fixture Setting Compound
- TT-P-595 - Preservative Coating, Canvas
- TT-P-781 - Putty & Elastic-Compound (for) Metal-Sash-Glazing +Cancelled, 1969, Superseded By TT-G-410
- TT-P-791 - Putty: Linseed-Oil Type, (for Wood-Sash-Glazing)
- TT-S-1543 - Sealing Compound: Silicone Rubber Base (for Caulking, Sealing, & Glazing in Buildings
- TT-S-1657 - Sealing Compound Single Component, Butyl Rubber Based, Solvent Release Type (for Build
- TT-S-1732 - Sealing Compound; Pipe Joint & Thread, Lead Free General Purpose
- TT-S-222 - Sealing Compound: Asbestos
- TT-S-227 - Sealing Compound: Elastomeric Type, Multi-Component (for Calking, Sealing, & Glazing I
- TT-S-230 - Sealing Compound, Synthetic-Rubber Base, Single Component, Chemically Curing (for Caul
- TT-W-156 - Water-Repellent Compound, Textile Finish
- TT-W-535 - Wood Preservative; Fluoride-Chromate Aresenate-Phenol Mixture
- TT-W-538 - Wood Preservative, Chromated Zinc Arsenate Mixture +Cancelled, 1967, No S/S Document+
- TT-W-546 - Wood Preservative; Acid Copper Chromate Mixture
- TT-W-549 - Wood Preservative; Ammoniacal Copper Arsenite Mixture
- TT-W-550 - Wood Preservative; Chromated Copper Arsenate Mixture
- TT-W-551 - Wood Preservative; Chromated Zinc Chloride Mixture
- TT-W-562 - Wood Preservative, Copperized Chromated Zinc Chloride +Cancelled, 1967, No S/S Documen
- TT-W-566 - Wood-Preservative, Creosote-Coal-Tar Solution +Cancelled, 1961, No S/S Document+
- TT-W-568 - Wood Preservative; Creosote-Petroleum Solution
- TT-W-569 - Wood Preservative, Osmosar (Osmosalts) +Cancelled, 1964, Nos/S Document+
- TT-W-570 - Wood Preservative; Pentachlorophenol, Solid (Cancelled, 1979, use ASTM-D1272)
- TT-W-572 - Wood Preservative; Water Repellent
- VV-S-190 - Sealing Compound (Dipcoat)