FSC 60GP: Fiber Optic Materials, Components, Assemblies, and Accessories -- General
The following documents are a part of this series:- AS-5750 - Loss Budget Specification for Fiber Optic Links
- DOD-STD-1864 - Fiber Optic Symbols (Cancelled, 1991, Superseded by MIL-STD-1864)
- DOD-STD-347 - Product Assurance Program Requirements for Fiber Optic Components (Superseded, 1989, by MIL-STD-790)
- EIA-440 - Fiber Optic Terminology
- EIA-455-102 - FOTP-102, Water Pressure Cycling
- EIA-455-107 - FOTP-107, Determination of Component Reflectance or Link/System Return Loss Using a Lo
- EIA-455-127 - FOTP- 127-a Basic Spectral Characterization of Laser Diodes
- EIA-455-16 - FOTP-16 Salt Spray (Corrosion) Test for Fiber Optic Components
- EIA-455-165 - FOTP-165, Mode-Field Diameter Measurement by Near-Field Scanning Technique
- EIA-455-166 - Fiber, Single-Mode, Measurements of Mode Field Diameter by Transverse Offset
- EIA-455-169 - FOTP-169, Chromatic Dispersion Measurement of Single-Mode Optical Fibers by the Phase-
- EIA-455-170 - FOTP-170, Cable Cutoff Wavelength of Single-Mode Fiber by Transmitted Power
- EIA-455.170 - Cable Cutoff Wavelength of Single-Mode Fiber by Transmitted Power
- EIA-455-173 - FOTP-173, Coating Geometry Measurement for Optical Fiber Side-View Method (ANSI/EIA/Ti
- EIA-455.174 - Fiber Optical, Mode Field Diameter of Single-Mode, by Knife-Edge Scanning in the Far F
- EIA-455-176 - FOTP-176, IEC-60793-1-20, Optical Fibres - Part 1-20: Measurement Methods & Test Proce
- EIA-455-178 - FOTP-178, IEC-60793-1-32 Optical Fibres - Part 1-32: Measurement Methods & Test Proced
- EIA-455-18 - Optic Components and Assemblies, Fiber, Acceleration Testing of
- EIA-455-184 - FOTP-184: Coupling Proof Overload Test for Fiber Optic Interconnecting Devices (ANSI/T
- EIA-455-188 - FOTP-188, Low Temperature Testing of Fiber Optic Components
- EIA-455-2 - FOTP-2, Impact Test Measurements for Fibre Optic Devices (ANSI/TIA/EIA-455-2C-98)
- EIA-455-21 - Fotp 21, Mating Durability of Fiber Optic Interconnecting Devices
- EIA-455-22 - Fotp 22, Ambient Light Susceptibility of Fiber Optic Components
- EIA-455-23 - Fotp 23, Air Leakage Testing of Fiber Optics
- EIA-455.24 - Fibres, Single-Mode, Water Peak Attenuation, Measurement Of
- EIA-455-25 - FOTP-25 Impact Testing of Optical Fiber Cables
- EIA-455-26 - FOTP-26, Crush Resistance of Fiber Optic Cable Interconnection Devices (ANSI/EIA-455-2
- EIA-455-28 - FOTP-28, Measuring Dynamic Strength & Fatigue Parameters Ofoptical Fibers by Tension
- EIA-455-3 - FOTP-3: Procedure To Measure Temperature Cycling Effects on Optical Fiber Units, Optical Cable, and Other Passive Fiber Components
- EIA-455-30 - FOTP-30, Frequency Domain Measurement of Multimode Optical Fiber Information Transmiss
- EIA-455-31 - FOTP-31 Proof Testing Optical Fibers by Tension
- EIA-455-32 - FOTP-32, Fiber Optic Circuit Discontinuities (ANSI/EIA/TIA-455-32-A-90) (R95) (R99)
- EIA-455-33 - FOTP-33 Optical Fiber Cable Tensile Loading and Bending Test
- EIA-455-34 - FOTP-34 Interconnection Device Insertion Loss Test
- EIA-455-35 - FOTP-35, Fiber Optic Component Dust (Fine Sand) Test (ANSI/EIA/TIA-455-35-A-90) (R95)
- EIA-455-37 - FOTP-37 Low or High Temperature Bend Test for Fiber Optic Cable
- EIA-455-39 - FOTP-39 Optical Fiber Cable Water Wicking Test
- EIA-455-4 - FOTP-4 Fiber Optic Component Temperature Life Test
- EIA-455-41 - FOTP- 41 Compressive Loading Resistance of Optical Fiber Cables
- EIA-455-42 - FOTP-42, Optical Crosstalk in Fiber Optic Components
- EIA-455-43 - FOTP-43, Output Near-Field Radiation Pattern Measurement Ofoptical Waveguide Fibers
- EIA-455-45 - FOTP-45, Method for Measuring Optical Fiber Geometry Using Alaboratory Microscope
- EIA-455.46 - Fibers, Optical, Spectral Attenuation Measurement for Long Length, Graded-Index
- EIA-455-48 - FOTP- 48 Measurement of Optical Fiber Cladding Diameter Using Laser-Based Instructions
- EIA-455-5 - FOTP-5, Humidity Test Procedure for Fiber Optic Components
- EIA-455-50 - FOTP-50, Light Launch Conditions for Long-Length Graded-Index Optical Fiber Spectral A
- EIA-455.51 - Multimode Glass Optical Fiber Information Transmission Capacity, Pulse Distortion Meas
- EIA-455.53 - Fibers, Optical, Attenuation by Substitution Measurement for Multimode Graded- Index O
- EIA-455-54 - Mode Scrambler Requirements for Overfilled Launching Conditions To Multimode Fibers
- EIA-455.55 - Fibers, Optical, Measuring Coating and Buffer Geometry of, End-View, Methods For
- EIA-455-56 - Test Method for Evaluating Fungus Resistance of Optical Fiber & Cable
- EIA-455-6 - Fotp 6, Cable Retension Test Procedure for Fiber Optic Cable Interconnecting Devices
- EIA-455-60 - FOTP-60 Measurement of Fiber of Cable Length Using and Otdr (TIA-455-60)
- EIA-455.63 - Fibers, Optical, Torsion Test For
- EIA-455-65 - FOTP-65, Optical Fiber Flexure Test
- EIA-455.65 - Optical Fiber Flexure Test
- EIA-455-66 - FOTP-66, Test Method for Measuring Relative Abrasion Resistance of Optical Waveguide C
- EIA-455-67 - FOTP- 67 IEC-60793-1-51 Optical Fibres- Part 1-51: Measurement Methods and Test Procedures- Dry Heat
- EIA-455-75 - Fluid Immersion Aging Procedure for Optical Fiber Mechanicalproperties (ANSI/TIA/EIA-4
- EIA-455-76 - Method for Measuring Dynamic Fatigue of Optical Fibers by Tension
- EIA-455.76 - Optical Fibers by Tension, Method for Measuring Dynamic Fatigue Of
- EIA-455.77 - Procedures To Qualify a Higher-Order Mode Filter for Measurements on Single-Mode Fiber
- EIA-455-81 - FOTP-81, Compound Flow (Drip) Test for Filled Fiber Optic Cable (ANSI/EIA/TIA-455-81-B
- EIA-455.83 - Cable To Interconnecting Device Axial Compressive Loading
- EIA-455-84 - FOTP-84 Jacket Self-Adhesion (Blocking) Test for Fiber Optic Cable
- EIA-455-85 - FOTP-85 Fiber Optic Cable Twist Test
- EIA-455.94 - Fiber Optic Cable Stupfing Tub Compression
- EIA-455-99 - FOTP-99, Gas Flame Test for Special Purpose Fiber Optic Cable
- EIA-526-10 - Systems, Dispersion Power Penalty in Digital Single-Mode, Measurement of
- EIA-526-4 - OFSTP-4, Optical Eye Pattern Measurement Procedure
- EIA-587 - Fiber Optic Graphic Symbols
- EIA-IS-46 - Test Procedure for Resistance To Soldering (Vapor Phase Technique) for Surface Mount D
- EIA-IS-50 - TP-45 Flame Test Procedure for Firewall Electrical Connectors
- EIA-RS46 - Fibers, Optical, Spectral Attenuation Measurement for Long Length, Graded-Index
- IEEE-812 - Standard Definitions of Terms Relating To Fiber Optics
- MIL-HDBK-277 - Fiber Optic Checkout Procedure for Military Applications (No Superseding Document)
- MIL-HDBK-278 - System Design Guide for Applying Fiber Optic Technology To Shipboard Systems (No Superseding Document)
- MIL-STD-1678/1 - Fiber Optic Cabling Systems Requirements and Measurements (Part 1: Design, Installation and Maintenance Requirements) (Part 1 of 6 Parts)
- MIL-STD-1678/2 - Fiber Optic Cabling Systems Requirements and Measurements (Part 2: Optical Measurements) (Part 2 of 6 Parts)
- MIL-STD-1678/3 - Fiber Optic Cabling Systems Requirements and Measurements Physical, Mechanical, Environmental and Material Measurements (Part 3 of 6 Parts)
- MIL-STD-1678/4 - Fiber Optic Cabling Systems Requirements and Measurements (Part 4: Test Sample Configuration and Fabrication Requirements)(Part 4 of 6 Parts)
- MIL-STD-1678/5 - Fiber Optic Cabling Systems Requirements and Measurements (Part 5: Design Phase, Supplemental and Legacy Measurements) (Part 5 of 6 Parts)
- MIL-STD-1678/6 - Fiber Optic Cabling Systems Requirements and Measurements (Part 6: Parts and Support Equipment Commonality and Standardization Requirements) (Part 6 of 6 Parts)
- MIL-STD-1864 - Fiber Optic Symbols (Superseded by EIA/TIA-587)
- MIL-STD-2052 - Fiber Optic Systems Design