FSC 5220: Inspection Gages and Precision Layout Tools
The following documents are a part of this series:- A-A-50685 - Level, Precision Master, Single Face
- A-A-50767 - Analyzer, Surface Finish
- A-A-58089 - Comparator, Bench Type, Electronically Amplified
- A-A-59120 - Gauge, Surface Plate Flatness Checking
- A-A-59572 - Gage, Comparator, Electric
- AS-22520/18 - Crimping Tools, Terminal, Hand, Wire Termination In-Service Inspection Gages for AS22520/17 Crimping Tools
- AS-22520/3 - Crimping Tools, Terminal, Hand, Wire Termination, Inspection Gage for Type I and Ii Tools
- AS-22520/35 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages for AS22520/34 Crimp Tools
- AS-22520/39 - Crimping Tool, Terminal, Hand, Actuated, Wire Termination, In-Service Inspection Gage for AS22520/5, /37, /38, and /44 Crimp Tools
- AS-22520/42 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage for AS22520/41 Crimp Tools
- AS-22520/43 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage for AS22520/40 Crimp Tools
- AS-22520/6 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages for Type III Tools (for AS22520/5 and /32 Crimp Tools)
- AS-22520/7 - Crimping Tools, Type 1, Terminal, Hand, Wire Termination for Wire Barrel Sizes 16, and Smaller
- AS-23003 - Gages - Inspection for MS23002 Crimping Dies (For Use With MS25036 Insulated Terminals) (STABILIZED Aug 2014)
- AS-25472 - Gage, In-Service-Inspection, for Use With MS25442 Crimping Dies (For Use With Aluminum Wire Terminals)
- AS-31971 - Gage Pin for Socket Contact Engagement Test
- DOD-STD-112 - Gage, Ring, Plain, Go
- GGG-B-121 - Bar, Sine, Plate Sine (and Fixtures)
- GGG-B-461 - Block, Step, Machinists
- GGG-G-61 - Gage, Plug and Ring, Plain and Thread
- GGG-P-441 - Plate, Angle, Adjustable and Solid
- GGG-P-453 - Plate, Surface, Cast Iron
- GGG-P-463 - Plate, Surface, (Granite) (Inch and Metric)
- GGG-P-61 - Parallels: Steel & Cast-Iron, Precision-Ground
- MIL-C-22520/18 - Crimping Tools, Terminal, Hand, Wire Termination In-Service Inspection Gage for MIL-C-22520/17 Crimping Tool
- MIL-C-22520/26 - Crimping Tool, Terminal, Hand or Power Actuated, Wire Termination, in Service Inspection Gages for MIL-C-22520/25 Crimping Tool (No Superseding Document)
- MIL-C-22520/3 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages
- MIL-C-22520/35 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gauges for MIL-C-22520/34 Crimp Tools
- MIL-C-22520/6 - Crimping Tools, Terminal, Hand, Wire Termination, In-Service Inspection Gages
- MIL-C-83988 - Comparator, Bench Type, Vertical Column, Electronically Amplified (Superseded by A-A-58089)
- MIL-C-83997 - Comparator Gage, Internal and External, Electronically Amplified (Superseded by A-A-58089)
- MIL-D-45608 - Designs and Drawings, Inspection Equipment (Superseded by DOD-D-1000)
- MIL-DTL-22520/39 - Crimping Tool, Terminal, Hand, Actuated, Wire Termination, In-Service Inspection Gage for
- MIL-DTL-22520/43 - Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage
- MIL-G-10944 - Gage, Dimensional Control
- MIL-G-22910/8 - Gage Inspection for m22910/7 Crimping Tool (Inactive 7-9-73)
- MIL-G-45653 - Gage, Cylindrical Plug and Ring, Plain
- MIL-G-45654 - Gage, Plug and Ring, Thread (No Superseding Document)
- MIL-G-46382 - Gage, Snap, Thread Roll
- MIL-G-83984 - Gage, Surface Plate Flatness Checking (Superseded by A-A-59120)
- MIL-G-87955 - Gage, Snap, Adjustable, Dial Indicating (No Superseding Document)
- MIL-G-87964 - Gage, Surface, Gage and Plate (No Superseding Document)
- MIL-HDBK-204 - Design of Inspection Equipment for Dimensional Characteristics
- MIL-I-45177 - Instrument, Tracer, Surface Roughness (No Superseding Document)
- MIL-I-83992 - Inspection Machine (Measuring, Digital Readout, and Automatic Data Processing), Electronically Operated (No Superseding Document)
- MIL-P-10310 - Packaging of Inspection Gages (Use MIL-G-10944)
- MIL-S-45176 - Specimen, Comparison, Surface Roughness (Flat) With Carrying Case (Superseded by ANSI-B46.1, Now ASME-B46.1)
- MIL-STD-110 - Gage, Plug, Plain Cylindrical Go (No Superseding Document)
- MIL-STD-111 - Gage, Plug, Plain Cylindrical, Not Go (No Superseding Document)
- MIL-STD-112 - Gage, Ring, Plain, Go (No Superseding Document)
- MIL-STD-113 - Gage, Ring, Plain, Not Go (No Superseding Document)
- MIL-STD-114 - Gage, Plug, Thread Go (Class X) for Unified American National Standard Internal Thread (No Superseding Document)
- MIL-STD-115 - Gage, Plug, Thread Not Go Unified- American National Standard Internal Thread (No Superseding Document)
- MIL-STD-116 - Gage, Ring, Thread Go (Class X) and Related Setting Plug Gages, Go and Not Go Plain Plug Minor Diameter Acceptance Check Gages for Unified and American National Standard External Threads (No Superseding Document)
- MIL-STD-117 - Gage, Ring, Thread, Lo (Not Go) and Related Thread Setting Plug Gages, Go and Not Go Plain Plug Minor Diameter Acceptance Check Gages for Unified and American National Standard External Threads (No Superseding Document)
- MIL-STD-118 - Gage, Snap, Plain Adjustable (No Superseding Document)
- MIL-STD-120 - Gage Inspection (Withdrawn, No Superseding Document)
- MIL-STD-133 - Cage, Plug, Plain Cylindrical, Go for Minor Diameter of Standard Class of Internal Thread (No Superseding Document)
- MIL-STD-134 - Gage, Plug, Plain Cylindrical, Not Go for Minor Diameters of Standard Classes 3F Internal Thread (No Superseding Document)
- MIL-STD-1452 - Gaging, General Principles of (No Superseding Document)
- MIL-STD-273 - Gage, Plug, Thread Setting, Class W, for Go Gages Unified Standard Classes 2a and 3a and American National Standard Class 3 External Threads (No Superseding Document)
- MIL-STD-274 - Gage, Plug, Thread, Setting, Class W, for Lo (Not Go), Gages, Unified Standard Classes 2a and 3a and American National Standard Class 3 External Threads (No Superseding Document)
- MIL-T-22910/4 - Tool, Gage-Inspection for m22910/2 Crimping Tool (Superseded by MIL-T-22910/8a)
- MIL-T-22910/5 - Tool, Hand, Gage-Inspection for m22910/3 Crimping Tool (Superseded by MIL-T-22910/8)
- MS-14038 - Gage, In-Service Inspection, for Ms14037 Contact Crimping Tool (Use MIL-C-22520/3)
- MS-23003 - Gages, Inspection for Ms23002 Crimping Dies (for Use With Ms25036 Insulated Terminals) (Superseded by SAE as-23003)
- MS-25316 - Gauges for Ms25312 Crimping Tool (No Superseding Document)
- MS-25340 - Gage,-Inspection, for Ms 25037 Crimping Tool, Electric Terminals
- MS-25472 - Gage-Inspection, for Ms 25442 Crimping Die (for Use With Aluminum Wire Terminal)
- MS-27832 - Gage - Inspection for Ms27828 Crimping Tool and Ms27831 Miniature Crimping Tool (Use MIL-C-22520/3)
- MS-3151 - Gage-In-Service Inspection, for Ms3150 Crimping Dies
- MS-3196 - Gage in Service Inspection, for Contact Crimping Tool
- MS-3197 - Gage Pin for Socket Contact Engagement Test (Superseded by SAE as-31971)
- MS-3199 - Gage - In-Service Inspection. for Ms3198 Contact Crimping Tool
- MS-3317 - Gage, In-Service Inspection, for Ms 3316 Terminal Crimping Tool
- MS-3434 - Test Gage, Contact Location and Retention Feature, MIL-C-0081511 Series 1 and 2 Connectors
- MS-3435 - Test Gage, Contact Location and Retention Feature, MIL-C-0081511 Series 3 and 4 Connectors
- MS-3460 - Test Gage, MIL-C-0026482 Series 1 or MIL-C-81703 Series 2 Contact Retention Feature
- MS-3461 - Test Gage, MIL-C-0026482 Series 2 or MIL-C-81703 Series 3 Contact Retention Feature
- MS-3462 - Test Gage, MIL-C-26482 Series 2 (Class N), MIL-C-81703 Series 3 (Class N) and MIL-C-0081511 Series 3 and 4 (Class l) Contact Retention Feature
- MS-75094 - Gages-Inspection for MIL-T-55619 Tool, Crimping, for Coaxial, Radio-Frequency, Connectors (No Superseding Document)
- MS-90406 - Gage, Ring, Spline (Go-No Go)
- MS-90414 - Gage, In-Service Inspection, for Ms90413 Terminal Crimping Tool (No Superseding Document)
- MS-90486 - Gage, in Service Inspection, for Use W1Th Ms90485 Crimping Dies, (for Use With Copper
- MS-90488 - Gage, in Service Inspection, for Ms 90487 Shielded Contact Crimping Tool (No Superseding Document)
- NAS-527 - Inspection Procedure for Flush Fasteners