ASTM-D1037 › Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 These test methods cover the determination of the properties of wood-base fiber and particle panel materials as follows:
Sections Size and Appearance of Boards (7-10 )
Strength Properties: Static Bending (11-20)
Tensile Strength Parallel to Surface (21-27)
Tensile Strength Perpendicular to Surface (28-33)
Compression Strength Parallel to Surface (34-40)
Fastener Holding Tests
Lateral Nail Resistance Test (41-46)
Nail Withdrawal Test (47-53)
Nail-Head Pull-Through Test (54-60)
Direct Screw Withdrawal Test (61-67)
Hardness Test (68-73)
Hardness Modulus Test (74-80)
Shear Strength in the Plane of the Board (81-86)
Glue-Line Shear Test (Block Type) (87-90)
Falling Ball Impact Test (91-95)
Abrasion Resistance by the U.S. Navy Wear Tester (96-99)
Moisture Tests:
Water Absorption and Thickness Swelling (100-107)
Linear Variation with Change in Moisture Content (108-111))
Accelerated Aging (112-118)
Cupping and Twisting (119)
Moisture Content and Specific Gravity (120-121)
Interlaminar Shear (122-129)
Edgewise Shear (130-136)
Compression-Shear Test (137-146)
1.2 There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards. The pertinent ones are listed in Table 1. A few of the test methods referenced are for construction where the wood-base materials often are used.
1.3 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keywords
Abrasion resistance; emwood; Accelerated aging/testing; emwood products; Appearance of materials; Bend testing; emwood products; Compression testing; emwood/wood products; Disk method; Falling ball test; Flexural strength; emwood products; Hardness tests; emwood products; Impact resistance; Interlaminar shear strength; Linear changes/linearity; Moisture analysis; emwood products; Nailhead pull-through; Nail pull resistance; Nails; Navy test; Particleboard; Particle panel materials; Screws; Shear testing; emwood products; Size; Specific gravity;emwood products; Swelling; Tension (tensile) properties/tests;emwood products; Twist; Water absorption;embuilding materials; Wood-based materials/applications; Wood products;emfiber/particle panel materials; evaluating properties of wood-base fiber particle panel materials-; selecting test procedures, methods,;
To find similar documents by ASTM Volume:
To find similar documents by classification:
79.040 (Wood, sawlogs and sawn timber)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A653Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM-A1008
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
ASTM-A568
Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Document Number
ASTM-D1037-12R20
Revision Level
2012 R20 EDITION
Status
Current
Modification Type
Revision
Publication Date
Nov. 12, 2020
Document Type
Test Method
Page Count
32 pages
Committee Number
D07.03